PROVISION OF CERTAIN REVENUE WORKS, MINOR WORKS ETC UNDER GE AMRITSAR CANTT

Material and labour for excavation in trenches, n.exc. 1.5m wide and n.exc. 1.5m in depth; for foundations, etc. or shafts, wells, cesspits, manholes, pier holes, etc. n.exc. 10Square Metre on plan and n.exc. 1.5m in depth and getting out in hard/dense soil complete all as specified and as directed

Returnig, filling in, incl spreading, leveling watering and well ramming in layers not exc 25 cm thick above or below ground level complete all as specified and as directed

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed complete all as specified and as directed

Material and labour for cement concrete type D2 1:4:8 (40mm graded aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour for 50mm thick cement concrete type B-1,1:2:4 (20mm graded aggregate complete all as specified and as directed.

Material and labour for Brick work built in cement mortar 1:6 using old size sub class "B" bricks in wall straight or curved on plan exc 6m mean eadius complete all as specified and directed .

Material and labour for rendering 15 mm thick on fair faces of brick work or concrete surface finished even and smooth (without using extra cement) in CM 1:4 , complete all as specified and as directed

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of cement base paints complete all as specified and as directed.

Supply and fixing framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete FE -290 Gde E-165

Material and labour for preparation of new steel surface over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Material and labour 75 mm thick, plain cement concrete 1:3:6, type C-1 using 20 mm graded mechaically crused stone aggregates, laid in 1:20 slop as in Plinth protection/paving/shafts including making joints at 3.00 mtrs intervals and at each corner, the joint shall be filled with mastic filling to full depth) comprising of one partheated hot below bitumen 85/25, two parts heated sand (by volume), surface fininshed even and smoot witout using extra cement complete all as specified. Note : The concrete shall be laid at a strech not exceeding 3 mtr in legth and width of joint shall not more than 12mm.

Excavating in post holes (or similar holes) in soft and loose each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm Specified and directed.

Material and labour for PCC 1:3:6) Type C2 using 40 mm graded aggregate in foundations, filling and mass concrete etc complete all as specified and directed.

Material and labourSteel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confoRunning Metreing to I. S.11611979, Fe 410-W (Gde E- 250) quality A (Size (50x50x2.9mm hollow square pipe) complete all as specified and directed.

Material and labour 2 mm thick Fibre glass reinforced translucent corrugated/plain sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall including Holes for nails or screws, hand punched through iron or mild steel not exc 6mm thickness, complete all as specified and directed.

Material and labour for broken bricks Hardcore of gauge n exc. 63 mm, deposited , spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

Material and labour 75mm thick Cement concrete type C-2, 1:3:6 (40mm graded aggregate ) as in floor complete all as specified and directed.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws all as directed.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in view cutter, fixed with self tapping screws all as directed.

Supply and fixing mild steel bands, straps, hooks for fire points, hand made sliding bolt, clamp, hold fast and like confiRunning Metreing to Fe-290 and gde-E-165

Supply and fixing Welded steel wire fabric n exc 4 Kilogram /Square Metre complete to wood or steel members

Material and labour reinforcement cement concrete (nominal mix) (1:2:4) type B-1, using 20mm graded crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material and labour for flat FoRunning Metre work to sides and soffits of floor or roof beams, lintels, cantilevers, shelves & Slab including supports etc for fair finished surface complete all as specified.

Material and labour for TMT bars mild steel bars, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality confoRunning Metreing to Fe-500D.

Material and labour for TMT bars mild steel bars, 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with claps quality confoRunning Metreing to Fe-500D

Brickwork with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

Material and labour for rendering 12mm thick cement plaster in cement mortar (1:6) on concrete surfaces as in wall , finished even and smooth without extra cement complete all as specified.

Material and labour for rendering 5mm thick on fair faces of brick work or concrete surface finished even and smooth (without using extra cement) in CM 1:3 on ceiling complete all as specified and directed .

Supply only liquid water proofing compound to mixed with cement mortar etc, complete all as specified directed by EIC.

Material and labour for preparation of new plastered ceiling surfaces applying two coats of white wash complete all as specified and directed by EIC.

Material and labour preparing New plastered surfaces on walls one coat of primer paint, and applying two coat of oil bound distemper with 1 mm wall care putty complete all as specified directed by EIC. (Interior)

Material and labour preparing New plastered surfaces applying two or coats of 100%Premium acrylic emulsion paint having VOC less than 50 Gm/litre and UV resitance as per IS 15489: 2004, Alkali & fungal resisitance , dirt resitance extterior paint of required shade (Company Depot Tinted) withsilidon addiitives @ 1.43 litr/10 Square Metre over and including priming coats of exterior priomer applied @ 0.90 litrs/10 Square Metre over new surfaces all as specified .

Material and labour for 100mm thick Cement Concrete 1:4:8 type D2 using (40mm graded aggregate as in sub base, complete all as specified and directed .

Material and labour for 40mm thick Cement Concrete 1:2:4 type B1, (20 mm graded aggregate) as in flooring, complete all as specified and directed .

Material and labourfor non skid/matt finish ceramic tiles, 7 to 8 mm thick, (square/ rectangular), area of each tile exceeding g 0.11 Square Metre but not exceeding 0.18 Square Metre sq.m in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of 15 mm thick cement mortar (1:6) complete all as specified and directed.

Material and labour for Glazed ceramic coloured tiles in vertical surfaces 350 x 250x7 /450x350 x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match, & incl 10mm thick rendering in CM 1:4 complete all as specified directed by EIC

Supply and fixing solid PVC door frame of size 50X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification and directed.

Supply and fixing factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' chanel having a PVC sheet strip of 20mm width stuck in side with solvent cement for stiles and plain colour PVC sheeets for top rail lock rail and bottom rail in either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be foitted in the MS frame welded/sealed to the stiles and rails with solvent cement all as specified and shown on drg.

Material and labour for box type steel ventilator made of ERW tube P-section of size 600x250mm outer frame (Single rebateed) comprises glazed shutter, frame of ERW tube and F1 2mm thick welded/screwsd to frame for fixing of shetts glass including fixture and fitting like as stopper , cleat pintal hinges, holdfast etc all as shown on drg No CEJZ/TD1019/08 sheet 1/3 to 3/3 dt 01 May 2008 complete all as specified, Note: Sheet glass and painting shall be measured and paid separately.

Supply and fixing aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed

Supply and fixing stainless steel butt hinges of size 100mm complete all as specified and directed.

Supply and fixing, extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and directed.

Supply and fixing 4.00 mm sheet glass, ordinary quality and glazing with oil putty in square n. exc 0.5 sq.m in each pane.

Supply & fixed in repair vitrous china wash basin, white, flat back, size 550x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, PVC watse pipe 32 or 40mm bore 60 cm long complete all as specified directed by EIC.

Supply and fixing PVC Connections 15mm size with PTMT nuts of length 450mm, completed all as specified and directed EIC

Supply & Fixed in repair 15mm bore bib taps cast copper alloy with crutch or butterfly handle screwed down ,screwed for iron pipe or brass ferrule completed all as specified and directed EIC.

Supply and fixing in repair CP brass Health faucet (hand shower) including flexible pipe of required length fixing to 15m dia pipe with brass check nut complete all as specifed and directed.

Supply & Fixed in repair 15mm bore fancy type pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure, with or without lettered "Hot or Cold" with long screwed for iron pipe completed all as specified and directed EIC.

Supply and fixing 1000 Ltrs Rotatioal moulded polyethylene water storage tanks (Cylindrical vertical with closed top hoisted and fixed in postion, including Dismantling of existing water tank complete all as specified directed by EIC.

Supply and fixing in repairs 20 mm float valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe or brass ferrule complete all as specified and directed

Supply and fixing in repairs 20mm stop valves, cast copper alloy, screwed down, high pressure, fancy type chromium plated, screwed, both ends for iron pipe or for unions complete all as specified and directed.

Supply and fixing 110 mm dia bore PVC (SWR) pipe (Type 'B') single socketed in trenches/floors in any length with rubber ring joints complete all as specified and directed.

Supply and fixing PVC (SWR) bend/Door bend any radius for 110 mm bore pipe incl jointing material complete all as specified and directed.

Supply and fixingPVC (SWR) junction single, (Single T) equal or unequal for 110mm dia bore as specified and directed.

Supply and fixing in repair 110 mm dia PVC (SWR ) floor trap/ nahani trap with grating, plain with grating including jointing with solvent cement complete all as specified and directed

Supply and fixing for Glass shelf assembly complete all as specified and directed

Supply and fixing Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed

Supply and fixing Hat and coat hooks, solid body, 175mm to 250 mm including screws complete all as specified and directed

S & F PVC (SWR) vent cowl equal or unequal for 110mm dia bore as specified and directed.

Supply & Fixed in repair Galvanised steel water Tubes 15 mm Dia, medium grade', galvanised,with all fitting; and fixed, including taking down the existing pipe to wall and ceiling and laid to floor, complete all as specified directed by EIC.

Supply & Fixed in repair Galvanised steel water Tubes 20 mm Dia, medium grade', galvanised,with all fitting; and fixed including taking down the existing pipe to wall and ceiling and laid to floor, complete all as specified directed by EIC.

Supply and fixing fixed in repair aluminium androised tubular towel rail, 20 mm dia D type , 60 cm long between flanges, complete all as specified directed by EIC.

Material and labour for preparation of New steel surface of any description not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint, complete all as specified directed by EIC.

Material and labour for 20mm thick screed bed or bedding layer of mortar for laying floor finishes in CM 1:4 complete all as specified and directed by EIC.

Material and labour 100mm thick plain cment concrete 1:4:8 type B-2 using 40mm graded crushed stone aggregate) as in floor complete all as specified and directed by EIC.

Material and labour for chequered cement concrete tiles 20cmx20cmx25mm thick, set and jointed and pointed in neat cement slurry in floors with grey cement and no pigment, complete all as specified and directed by EIC.

Supply and fixing rotational moulded polyethylene water storage tank of 500 ltr capacity (cylinderical vertical with closed top) Triple layer Food grade hoisted and fixed in position, kept over the height of hot water tank of solar water heater on MS angle iron frame of size 35mm x 35mm x 5mm duly grouted in PCC 1:3:6, complete all as specified and directed Note: Cost of MS angle iron frame and PCC work shall be measured and paid separtely uder relvant item of the contract. Make Sintex/Polycon/Sheetal

Supply and fixing/ installation and testing industrial Desert cooler heavy duty of tank capacity 20-50 Ltrs, plastic material,three phase capacity 3 HP to cover area of 1500 to 3000 sqft complate all as specified and directed.

Material and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6.3 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised earth wire of size 4 mm dia by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 15 mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) including testing complete all as specified and as directed.

Supply and fixing galvanized iron steel tubing medium grade 20 mm bore with all fitting and fixed to walls, ceiling and laid in floor complete all as specified Note- Quoted rate will include the cost of making water connection from existing supply line and making good of the wall surface etc all as specified.

Material and labour for sub main wiring with 1100 volt grade four single core PVC insulated and unsheathed FRLS cable with stranded copper conductor 4 Square Metrem drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 1 Square Metrem multi - stranded copper conductor as earth wire in green colour complete all as specified and directed.Make of wire : Polycab/RR Kabel/Finolex

Supply and fabricate MS ladders Supports railings etc incl cutting welding grouting in PCC for Bldg P-12 A complete all as specified and directed.

Supply and fixing Triple pole and neutral enclosure with a thre pin and earth plug and socket complete with one Triple pole MCB complete all as specified and directed by E-in-Charge Make Legrand/Siemens/Schneider

Supply and fixing rotational moulded polyethylene water storage tank of 500 ltr capacity (cylinderical vertical with closed top) Triple layer Food grade hoisted and fixed in position, kept over the height of hot water tank of solar water heater on MS angle iron frame of size 35mm x 35mm x 5mm duly grouted in PCC 1:3:6, complete all as specified and directed Note: Cost of MS angle iron frame and PCC work shall be measured and paid separtely uder relvant item of the contract. Make Sintex/Polycon/Sheetal

Supply and fixing of Air Ducting and return Air Ducting both made out of commercial grade GI sheet of thickness 24 Gauge confiRunning Metreing to IS:277 with Zinc coating of not less than120 grade, site fabricated as per SMACNA-1995 standards and as per IS:655. Make : Sail/ Tata /Jindal

Supply and fixing of theRunning Metreal insulation of internal duct with Nitrile sheet class 'O' (FR) of size 13mm and covered with glasscloth and finished with starbond. Make of insulation : K Flex/ A flex/ ARunning Metreacell and all other equivalent makes specified in Appendix'B'

Material and labour for point wiring complete with 1.5 Square Metrem single core PVC insulated sheathed multi-stranded, copper conductor FRLS grade cable of 1100 volts grade confoRunning Metreing to IS:694 drawn through and including non metalic rigid PVC conduit, medium grade, ISI marked, not less than 20mm bore with conduit accessories concealed on wall and ceiling/roof etc, with provn for fixing modular metal flush boxes not less than 1.0 mm thick of suitable modules, concealed in walls with modular white plated cover as top cover fixed with screws for housing switches, socket outlets, fan regulators etc, including provn of 1.5 Square Metrem nominal cross sectional area, PVC insulated, FRLS, sheathed, 1100 volt grade,multistranded single core green colour copper conductor for earth continuity connected to earth dolly complete all as directed NOTE: (i) Modular metal flush boxes concealed in wall with suitable cover plate for mounting switch, sockets, regulator etc. and cost of cutting chases & making good as existing to disturbed surface with cement mortar, if required any shall be deemed to included in the quoted rates. (ii) Modular fittings/fixtures such as switch, socket, regulator, etc., shall be measured and paid separately as under relevant item.

(a) One light point controlled by one switch

(c) One 5 Amps outlet point on same board with other switches/sockets

(d) One 3 pin 5 Amps socket outlet on independent board.

All as per Item No78 here-in-before but with 2.5 Square Metrem (nominal area) PVC insulated and PVC sheathed FRLS cable stranded copper conductor for modular one 3 pin 15 Amps socket outlet independent with earth wire PVC insulated and unsheathed FRLS cable of size 1.5 Square Metrem as earth lead complete all as specified and directed

All as per ser item No.82 here in above but point wiring with 4.0 Square Metrem FRLS cable and 4.0 Square Metrem cable earth continuity wire for one 3 pin socket outlet,15 Amps on independent board.

Supply and fixing modular switch 1 way 6A, 240 volts, 1 module complete all as specified and directed

Supply and fixing modular switch 1 way 16A, 240 volts, 1 module complete all as specified and directed

Supply and fixing modular socket, 6A, 240 volts, 2/3 pin combined 2 module, flush type all as specified and directed

Supply and fixing modular socket, 6A/16A, 240 volts, 2/3 pin combined 2 module flush type all as specified and directed

Supply and fixing ceiling rose surface PVC/Polycarbonate, isolated body with face Bakelite 65x50 mm three teRunning Metreinal complete all as specified

Supply and fixing LED lights fitting 1x 20W, 220V, AC, 5700K, decorative box type with driver, double sided connection, CRI> 80, PF>95%, THD<10%, Lumen>2100 lm including LED tube light of make: Havells or equivalent in Philips/Crompton, connecting up with 3 core flexible copper conductor cable (1.0 mm² size/core) from ceiling rose complete all as specified and directed.

Supply and fixing PLUTO NEO LED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type of make: Havells or equivalent make of Philips/Crompton, with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases (1.0 mm² size/core) complete all as specified and directed.

Supply and fixing Dusk & dawn roadway luminaries 35 Watt, 230 V AC, 5700K outdoor type with epoxy black powder coated sheet of make: Havells or equivalent make of Philips/Crompton, high pressure die-cast aluminum hosing and heat resistant complete with impact and corrosion resistant including theRunning Metreal management in multiple optics, PF>95%, THD<10%, Lumen>4500 lm with IP 65/66 protection complete incl connecting wire with flexible PVC insulated copper cables from ceiling rose to fitting including driver, lamp bracket made of 32mm bore galvanised iron light grade pipe made to shape having overall length not exceeding 1.5 mtr, through mild steel clamp of 25mm width and four Nos. nuts, bolts & washers of 12mm dia, 100mm long fixed to wall with all other fittings complete and testing all as specified and directed.

Material and labour for distribution board made out of sheet metal enclosure (CRCA sheet) dust and veRunning Metrein proof, double door, SPN 12 way, 240 volts grade with 200 Amps insulated rated bus bar with nickel plated brass, isolated neutral bar and door earthing, earth bar IP- 43 protection with poly urithene (PU) gasketing, IK-08 Mechanical impact resistance, flush to wall, including testing suitable for fixing MCB SPN, SP etc, complete all as directed NOTE: (i) MCB DB & MCBs should be of same make as mentioned above. (ii) Necessary blank plates if required any to cover the blank MCB's place in DB and the rate shall be deemed to included in the quoted rates.

Supply and fixing MCB of SP 5 to 32 Amps current carrying capacity, 240V, 10KA 'C' curve, ISI marked, fixed in the MCB DB complete confoRunning Metreing to IS/IEC-60898-1 2002 with connection testing and commissioning including taking down old unsv one from the site complete all as directed

All as per ser item No. 93 above but for MCB SPN 32/40 Amps

Material and labour, Sub main wiring with two single core 4 Square Metrem (nominal area) stranded copper conductor FRLS PVC insulated and unsheathed cables drawn in and including non metalic PVC regid conduit medium grade of suitable size with all standard fittings, concealed including one run of continous PVC insulated stranded copper conductor FRLS cable 4.0 Square Metrem (nominal area) for earth continuity, including taking out and removal of old sub main wiring complete all as specified and directed Note:- 1 Two runs of 4 Square Metrem main cable one run of 4.0 Square Metrem for earth cable & condut shall be measured as one unit/ one running meter.2. rate quoted shall be deemed to include cutting chases for concealing condut and making good in cement cortar 91:4) or PCC (1:2:4) as required.

Supply and fixing Wall mounted fan of 400mm sweep plastic body and blade including pull cords for speed regulation & wide oscillation control, with 1300 RPM, 60 air delivery, 50 Watt, colour as per the direction of Engr-in-Charge complete all as specified and directed

Supply and fixing exhaust fan, heavy duty, steel body AC single Phase, 230V of size 300mm sweep, with blades and frame and louvers complete of make Havells/Crompton/Orient, fixed/grouted to wall with suitable bolts, nuts etc., and connecting up with & including 3 core flexible copper conductor cable from ceiling rose to exhaust fan including cutting hole suitable for fixing exhaust fan complete all as specified and directed

Sheet metal single pole and neutral enclosure, 240 volts with a two pin and earth plug and socket complete with one single pole MCB capacity 20 amps as specified and directed (for AC and geyser).

Supply and fixing Lamp holder battan type, PVC/Polycarbonate type with back plate suitable for batten fittings including presto plastic board for resting to holder complete all as directed

Supply and fix of security light fitting LED 45 Watt with aluminum pressure dia cast housing protection Including suitable size GI Bracket and accessories complete mounted including connection with 3 core PVC insulated overall sheathed flexible cable with muyltistranded copper conductor of size not less than 1.5 sq mm from celing rose to fitting teRunning Metreinal including taking down old security light fitting all as specified and as directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply & fixing exhaust fan, heavy duty, steel body AC single Phase, 230V of size 300mm sweep, with blades and frame and louvers complete fixed to wall with suitable MS bolts, grouted to wall including connecting up with & including 3 core flexible copper conductor cable from ceiling rose to exhaust fan complete all as specified and directed.

Suuply and fixing MCB SPN, 240 volts, 40 to 63 Amp, rupturing capacity 10 kA, ‘C’ curve type complete with connection testing and commissioning complete all as specified and directed.

Supply,fixing, testing and commissioning of electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, theRunning Metreostate, NRV, with hot and cold connection pipes complete all as specified and directed.

Supply and Laying in trenches/drawn through pipes or in road crossings/paths/drains/ ducts/floors/along poles/equipments etc., of LT cable under ground, heavy duty, aRunning Metreoured, XLPE insulated with multi-stranded aluminium conductor cable confoRunning Metreing to IS-7098 Part-I (1998), 1100 Volts grade of 10 Square Metrem 4 core nominal cross sectional area including necessary double compression copper gland and connecting up using suitable size aluminium lugs testing, incl taking down old unsv one from site complete all as specified and directed NOTE: Excavation & earthwork will be measured and paid separately

Supply and laying double 40mm bore, High density polyethylene pipes (HDPE), wall corrugated (DWC) of pressure rating 6 Kilogramf/cm2 laid in trenches for protection of LT XLPE aRunning Metreoured cable laid in trenches all as spcified and directed

Supply and fixing LED flood light 70 watt 230 V AC outdoor/Indoor type with theRunning Metreal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp.

Material and labour One light point or one fan point controlled by one switch with cables 1.5 sq. mm size PVC insuated unsheathed 1100 volt grade single core multistranded copper conductor cable FRLS drawn into and including PVC casing capping/PVC Conduit of suitable size with all its neccessary fittings and accessories on wooden/stone/brick masonry wall surface and sunk cast iro on pressed steel teRunning Metreinals boxes for mounting fittings like switches,sockets,lamp holders, sketch fittings and coverd with 3 mm thickplastic laminated bakelite sheet cover fixed with brass screws and cup washers including one continous run of pvc insulated (green colour) 1.5 Square Metrem size multi stranded copper conductor cable as in earth wire and connected to common earth dolly complete all as specified and directed