COMPREHENSIVE MAINT ( B/R ITEMS ) OTM ACCN OF MAJOR UNITS OF BHALUKMARA AREA UNDER GE JORHAT

Amount

NOTES :The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Dismantling plain or corrugated steel sheeting, any gauge, any thickness, including Nainital or similar pattern roof coverings complete all as directed.

Supply and fixing of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Supply and fixing of pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.

Dismantling of wrought iron or mild steel work any description and fixed in any position complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats and similar works .conforming to Fe- 290 (Gde E- 165) etc complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness including cover fillets and removing unserviceable materials from site of work complete all as specified and directed.

S&F Anodised aluminium snap grid with Tee section 35mm x 25mm x 1.40mm, , cross Tee section 23.5mm x 23.5mm x 1.40mm and wall cleat of aluminium angle 25mm x 25mm x 1.40mm on side / edge frame work of size 605x605mm with hangers 4mm dia GI wire adusting label fixed to roof trusses by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fastener 12.5mm dia, 40mm long complete all as specified and as directed.

S&F 4mm thick high pressure steam cured non asbestos fibre cement designer board as per IS 14862 with applying of two coats of acrylic distemper over a coat of primer complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) of area not exceeding 1.50 Sqm each including all building hardwares etc complete all as specified and as directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frame) of area exceeding 1.50 Sqm but n.exc 4 sqm each including all building hardwares etc complete all as specified and as directed.

Taking down shutter of any description area exceeding 1 sqm but not exceeding 2 sqm each and removing from site of work complete all as specified and as directed.

S&F Pressed steel frames of size 105mm x 60mm and thickness of MS sheet 16 gauge for doors with double rebate , including necessary fixing lugs, hinges, lock strike plate,as per IS 4351 & IS 513 etc complete all as specified and as directed.

S&F Pressed steel frames of size 125mm x 60mm and thickness of MS sheet 16 gauge for doors with double rebate , including necessary fixing lugs, hinges, lock strike plate, etc as per IS 4351 & IS 513 complete all as specified and as directed.

S&F 35 mm thick IInd class hardwood, Glazed and skeleton shutters, factory made , open rebated and prepared to receive glass, gauze, etc. (with any Nos of sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F Flush shutters, 30 mm thick ,solid core construction, with block board core and plywood face panels, commercial type on both sides, conforming to IS 2202 (Part-I) complete all as specified and directed.

S&F Well seasoned IInd class hard wood, well seasoned , plain, solid, straight chowkhat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

M&L for block board 18/19 mm thick grade 2 quality, interior grade with decorative type with decorative face veneer on both faces, fixed with screw to timber frame work framed work as in cupboard.incl. leaping all aroundm etc complete all as specified and as directed.

Material and labour for Solid PVC door frame of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with Mild Steel square tube, suppling & fixing in opening as per drawing complete all as specified and directed.

Material and labour for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawingcomplete all as specified and directed.

S&F 100 mm size butt hinges "medium weight" cold rolled mild steel complete all as specified and directed.

S&F 75 mm long butt hinges, "medium weight" cold rolled mild steel complete all as specified and directed.

S&F 125 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 100 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 250 mm long aluminum alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of steel, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloy complete all as specified and as directed.

S&F 125 mm extruded aluminum alloy handles, cast type, anodized complete all as specified and as directed.

S&F 100 mm extruded aluminum alloy handles, cast type, anodized complete all as specified and as directed.

S&F 300mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F continuous (Piano) hinge mild steel 40 mm wide flap when open, bright finish or electrogalvanised complete all as specified and directed.

S&F 75 mm Hasp and staple, safety type, aluminium with mild steel hinge pin including bolt to hinge plate and fixed with screws aluminium anodised complete all as specified and as directed.

S&F in repair 25 mm Harrison rails, mild steel, chromium plated with fixing ornamental brackets, stops, rollers etc. complete as specified and as directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors,windows, ventilators andpartitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top,bottom and sides withrequired EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitredand jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainlesssteel screws, all complete as per relevant TD drawings , specified and as directed.by the Engineer-in-Charge. Note :- Weight of Aluminium Sec shall not be less than 0.55 Kg / RM and shall be approved before incorporation at site.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gapsat junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall besmooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snapbeading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per relevant TD drawings , specified and as directed.by the Engineer-in-Charge. Note :- Weight of Aluminium Sec shall not be less than 0.55 Kg / RM and shall be approved before incorporation at site.

Supply and fix 4mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50sqm in each pane complete all as directed.

Supply and fix 4mm thick sheet glass, ordinary quality and glazing with oil putty in squares exceeding 0.50sqm in each pane complete all as directed.

S&F in repair Aluminiun (extruded section body) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg , ISI marked complete all as specified and directed.

S&F in repair factory made steel window with side hung shutter including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovatailed or welded as per IS.1038 etc complete all as specified and as directed.

S&F in repair factory made steel window with side hung shutter including projecting type hinges with steel handle and steel peg stay complete without glazing bars dovatailed or welded as per IS.1038etc complete all as specified and as directed.

S&F Chimney bars (straight or camber) tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 etc complete all as specified and directed.

S&F in repairs factory made Steel ventilator with top hung shutter incl. box type hinges with steel handle and steel peg stays complete with glazing bars welded as per IS.1038 etc complete all as specified and as directed.

Hacking out old broken glass (any thickness, size,quality or description) from steel/wooden frames or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads complete all as specified and directed.

S & F stainless steel wire cloth, 0.36mm nominal dia. of wire and average width of aperture 1.40mm fixed with tinned tacks, or stainless steel wire staples including all cuttings, wastage, etc complete all as specified and directed.

S & F in repair stainless steel wire cloth , 0.36mm nominal dia. of wire and average width of aperture 1.40mm fixed with tinned tacks, or stainless steel wire staples including all cuttings, wastage, etc complete all as specified and directed.

S&F mild steel flat iron 25 x 3 mm as in band, straps, hold fasts etc and similar small articles conforming to Fe-410-0 or Fe-310-0 complete all as specified and as directed.

Demolition of cement concrete ( un-reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing debris to a distance n.exc. 50 m etc complete all as specified and as directed.

Material and labour for 75 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in floor / path / plinth protection , finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for providing 40 mm thick plain cement concrete M-15 using 20mm graded aggregate laid in alternate panels in floor, finished even and smooth without using extra cement etc complete all as specfied and directed

Material and labour for providing Plain cement concrete M-15 using 20mm graded aggregate as in roof kerbs or mud stops, filling around hold fast etc. to rounded or chamfered on edges etc complete all as specfied and directed

S&F Plastic dividing strips 38mm wide and 1.5mm thick inserted in position conforming to design in PCC floor etc complete all as specified and directed

Material and labour for Plain cement concrete M-10 using 40mm graded aggregate as in surface channels and drains etc complete all as specfied and directed

M&L for forming extra fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc. complete all as specified and directed

Demolition of Reinforced cement concrete in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and removing debris to a distance n.exc. 50 m etc complete all as specified and as directed.

Material and labour for TMT Bars Fe 500D 10mm dia & over cut to length bent to shape required inculding cranking bending spirally hooping for columns etc and binding with MS wire ennealed less than 0.9mm dia or securing with clip complete all as specified and directed.

Material and labour fo TMT bars Fe 500D of 6 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel (annealed) wire not less than 0.90 mm dia or securing with clip complete all as specified and directed.

M&L for Precast Reinforced Cement concrete M-15( Nominal Mix) using 20mm graded stone aggregate as in cover slabs of drains set in cement sand mortar (1:4) including necessary form work complete all as specified and as directed by the Engr in Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to stores and rubbish off the MOD premises complete all as specified and as directed.

S&F 18-20 mm thick Granite of any type work table rubbed and polished in steps, jambs,pillars,cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed in cement mortar (1:6) etc complete all as specifed and as directed.

Material & Labour Glazed ceramic tiles 450 x 300 x 7 mm(Coloured) on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete over 10mm thick screed bed vertical layer in CM (1:4)all as specified and as directed.

M&L for vitrified ceramic tiles 10 mm thick dark shade square / rectangular shape,ISI marked area of each tiles not excedding 0.36 sqm in floor set and jointed in neat cement slurry and pointed in cement mixed with colour pigment to match over 15 mm thick screed bed or bedding layer in cement mortar(1:6) as in floors for receiving tiles complete all as specified and as directed.

Taking down wall panelling and similar work of any description etc complete all as specified and as directed

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing etc complete all as specified and as dikrected.

S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specification and drawing etc complete all as specified and as dikrected.

M&L for preparation of new or previously un-treated wood and wood base surfaces of any description, not otherwise described exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new or previously un-treated steel surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement sand mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles of any description or any position etc complete all as specified and as directed.

M&L for Brickwork with subclass ‘B’ bricks, old size ,straight or curved on plan exc 6m mean radius built in cement sand mortar 1:6 etc complete all as specified and as directed.

Taking up or down steel tubing and connections, 15mm bore and removal of unserviceable pipe from site of work complete all directed.

Supply and fix 15mm bore galvanized steel tubing "medium grade" with all GI fittings and fixed complete to walls and ceiling or laid in floor complete all as specified and as directed.

Taking up or down steel tubing and connections, 20mm bore and removal of unserviceable pipe from site of work complete all directed.

Supply and fix 20mm bore galvanized steel tubing "medium grade" with all GI fittings and fixed complete to walls and ceiling or laid in floor complete all as specified and as directed.

S & F in repair of 15 mm bore bib taps, cast copper alloy fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repair 15 mm bore ball brass valves, high pressure, with olythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repair 15mm dia stop valve fancy type chromium plated concealed type, screwed down high pressur, with crutch or butterfly handle, screwed both hands for iron pipe or for union etc complete all as specified and directed.

S&F in repair 15mm dia Angle cock fancy type chromium plated screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions. etc complete all as specified and directed.

S&F in repair 500 ltrs rotational moulded polythytene water storage tanks , double layered (cylindrical vertical with closed top) hoisted and fixed in position as specified in SSR Part I including 20 mm ball brass valves high pressure with polythene float and nut complete including dismantling of old one all as specified and as directed.

S&F 1000 ltrs rotational moulded polythytene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position as specified in SSR Part I including 20 mm ball brass valves high pressure with polythene float and nut complete including dismantling of old one all as specified and as directed.

S&F 10 ltr capacity PVC valveless syphone action dual flush type (5/10 Ltrs), flushing cistern, low level, white with inlet, ball valve float and handle incl brackets with PVC high flush pipe including dismantling old unserviceable one complete all as specified and directed.

S&F in repair Vitreous china squating pan orissa pattern size 580X 440 mm white with intregal foot rest complete including lime concrete (excluding flushing cistern and flush pipe) but connecting to flushing pipe, anti-symphonage pipe including provn of cement concrete bed 1:2:4 using 20 mm graded stone aggregate etc. complete all as specified and directed.

S&F in repair Vitreous china wash hand basin 550mm x 400mm (flat ball type) any size including cutting for and pinning in ends of brackets 20 mm GI tubing medium grade including waste coupling, waste water pipe complete all as specified and directed.

Supply and fixing in repair Vitreous china urinal bowl, flat back of size 465x355x265mm (minimum) white with grating and union for discharge pipe (excluding flushing cistern,flush pipe and waste pipe) complete all as specified and directed.

Supply and fixed in repair Vitreous china wash down water closet pan (Pedestal pattern), 'P' or 'S' trap white, including fixing bolts nut & plastic water closet seat back excld flushing cistern and flush pipe, etc complete all as specified and directed.

S&F in repair Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915 mm x 460 mm and bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F PVC waste pipe 32 mm dia and 900 mm long complete all as specified and directed.

S & F in repair of 15 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S & F in repair of 20 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Taking down eaves gutters and rain water pipes (any ize or patterns) including all heads,shoes,bends,swan-necks etc. complete all as specified and directed.

S&F PVC (SWR) soil or waste pipe 110 mm bore single socket in any length type 'B' with rubber ring joints laid in trenches or floor / wall complete all as specified and directed.

S&F PVC ( SWR) soil or waste pipe 75 mm bore single socket in any length type 'B' with rubber ring joints laid in trenches or floor / wall complete all as specified and directed.

M & L for PVC (SWR) Floor trap of 75 mm outlet plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) bend in any radius 110 mm dia bore with access dore complete all as specified and directed.

S&F PVC (SWR) bend in any radius 75 mm dia bore with access dore complete all as specified and directed.

S&F PVC (SWR) junction single (single T) equal or unequal 110 mm dia bore with access dore complete all as specified and directed.

S&F PVC (SWR) junction single (single T) equal or unequal 75 mm dia bore with access dore complete all as specified and directed.

Taking down existing roof treatment / tarfelt complete of any description over roof surface with wire brush and cleaning the surface with clean potable water and M&L for provn of PP modified polymeric water proofing treatment to approchable/Unapprochable RCC roof as per description below including necessary testing such as pond testing etc as after completion as per relevant IS:- ( a) 25mm thick PCC M-15 using 12.5 mm stone aggregate as in roof padding, weathered or chamfered , finished even and fair without extra cement . (b) Preparation of RCC roof surfaces and providing 15mm thick screed bed of cement plaster in cement sand mortar 1:4 mixed with water proofing compound as per manufactures instruction and applying bitumenous based primer conforming to IS-3384 @ 0.50 Kgs per Sqm on prepared surface till the surface is properly impregnated. (c) Applying one coat hot air blown bitumen of 85/25 grade @ 1.2 Kg per sqm. (d) M&L for laying of APP modified Polymeric Membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application consisting of centre core of minimum 90 micron HM HDPE processes on both sides with a high quality polymeric asphaltic mix with further protected with thermofusible HM HDPE film with a over lap of 100mm on both sides and ends all as specified. (e) Applying one coat of hot bitumen of 85/25 grade @ 1.2 Kg/sqm. (f) Applying one coat of heat resistant aluminium paint over bituminous surfaces @ 0.15 litre / Sqm or as per manufacturer's instruction .

Supply and fix Anodised aluminium frame powder coated for partition (minimum thickness of powder coating 50 micron) with one or more rebates including and joining cleat for fixing , glazing clips, rubber packing screws etc.all as specified and as directed by Engr-in-Charge.

S&F 12 mm Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame/aluninium frame work etc complete all as specified and as directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

M&L for Rendering 15 mm in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

M&L for Rendering 5 mm in Cement Mortar 1:3 on fair faces of on concrete surface ceiling finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for Rendering 5mm thick cement plaster in Cement sand Mortar (1:4) mixed with water proofing liquid compound @ 3% of cement used or as per manufacturer's instruction over and including 10 mm thick cement plaster (1:4) ,on other than fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement etc complete all as specifed and as directed. Note:- Water proofing compound shall be measured and paid separately

Supply only Liquid water proofing compound ISI marked etc complete all as specified and directed.

Material and labour for Preparation of newly plastered ceiling surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade over and including a coat of primer and 1 mm thick cement based wall care pujtty as per manufacturer’s specification complete all as specified and directed.

Material and labour for Preparation of newly plastered wall surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade over and including a coat of primer and 1 mm thick cement based wall care pujtty as per manufacturer’s specification complete all as specified and directed.

M & L for preparation of newly plastered surfaces of walls, finishing walls with textured exterior paint of required shade : two coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm and applying plaster of paris putty of 1 mm thickness to prepare the surface even and smooth complete all as specified and as directed by Engineer in charge.

M&L for applying three coats of white washing over newly plastered surfaces of wall including necessary preparation etc complete all as directed.

Material and labour for complete removal of existing treatment over old or previously treated wall surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade over and including a coat of primer and 1 mm thick cement based wall care pujtty as per manufacturer’s specification complete all as specified and directed.

M&L for applying one coat of white washing over old or previously treated surfaces of wall including necessary preparation by washing with water and rubbing down etc complete all as directed.

M&L for applying one coat of white washing over old or previously treated surfaces of ceiling including necessary preparation by washing with water and rubbing down etc complete all as directed.

M & L for complete removal of existing treating over wall surfaces & applying two coats of acrylic base weather shield paint ( Exterior emulsion ) (1st quality) @ 1.67 Litre / 10 SQM over and including one coat of exterior grade primer @ 2.2KG / 10Sqm including 1 mm thick wall care putty cement based etc complete all as specified and as directed.

Materials and labour for complete removal of smoke shoot, moulds, mos and efflorescent salts and trading oil and greasy spots,removal of vegetation from old decorated surfaces of wall and applying two coats of cement base paint including preparation of surfaces all as specified and directed by the Engr-in-Charge

Materials and labour for removal of smoke shoot, moulds, mos and efflorescent salts and trading oil and greasy spots,removal of vegetation from old decorated surfaces of wall and applying a coat of cement base paint including preparation of surfaces all as specified and directed by the Engr-in-Charge

M&L for preparation of old painted wooden surfaces of any description, not otherwise described for, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

M&L for preparation of old painted steel surfaces of any description over 10cm width or girth, not otherwise described for and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted CGI / PGI roof sheet ssurfaces of any description over 10cm width or girth, not otherwise described for and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for oblitering of old figures (stops, Commas, Short Lines,Dashes,Hyphens,Brackets etc). and rewritting with synthetic enamel paint to match with existing letters complete all as specified and as directed.

M&L for oblitering of old writting letters or figures(block,Roman,Italic or Indian) n.exc 30 cm height for writting Bldg Nos,Block Nos and Quarter Nos etc. and rewritting with synthetic enamel paint to match with existing letters with existing painted background complete all as specified and as directed.

Supply and fixing in repair Door closer hydraulically regulated,designation No. 3,universal type aluminium die cast body, suitablefor door shutters of 851to 1000 mm in width and of weight between 61 to 80 kg , ISI marked and fixed complete all as specified and directed.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

RAJGURU & CO (BID ID -3068049)

SHRI RAJEN PASWAN (BID ID -3068197)

THE SUPPLY AGENCY (BID ID -3068711)

Chief Builders &Consultants (BID ID -3068911)

M/S BARUAH ELECTRICALS (BID ID -3068185)

NIHAR ENTERPRISE (BID ID -3067664)

A M CHOUDHURY AND CO (BID ID -3068254)

SUBHAS CONSTRUCTIONS (BID ID -3068120)