SPPWNIT 22 AAREY

Amount

Civil Work

Providing and fixing double scaffolding system (cup lock type) on the exterior

Providing, Erecting double scaffolding for external plaster and other repair

Raising of scafolding to reach the entire surface area of bridge. upto 10m

Providing and erecting supports to the structurally distressed floor/roof with

Providing and laying high density plastic sheet on the roof and other areas for

Plaster of Paris covering of 30mm thickness over the historic floor area with a

Careful Packing of sculpture details/ decorative grill work/ delicate tracery and

Removing R.S. girders of any size and span, lowering the same and stacking

Removing G.I.or A.C. sheet roofing including purlins, principal rafter etc.

Dismantling the R.C.C. work 1:2:4 and sorting out the materials such as steel

Removing cement tiles, or marble or polished shahabad floor or dado without

Removing lime or lean cement concrete including stacking the spoils as

Dismantling the existing timber sections like joists, rafters, posts, purlins,

Providing and fixing well seasoned Burma Teak Wood full length new

Fixing only Seasoned Teak wood common rafters, purlins and purlin cleats, hip

Providing and laying Cast insitu / Ready Mix cement concrete M-30 of trap /

Providing and laying Cast insitu / Ready Mix cement concrete M-30 of trap /

Providing and applying “high strength, non shrink free flow grout

Providing and fabricating structural steel work in rolled sections like joists,

Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel) bar

Providing and fixing SS stitch grouting for masonry repairs and cracks as

Providing injecting and grouting in stone masonry walls, vault & dome, lime

Repairing of honey combed or spilling area by chipping out the damaged

Providing & applying structural grade epoxy approved bond coat prior to

Providing and applying well mixed polymer cement slurry in ratio 1:2 over well

Providing and applying anti corrosive treatment with epoxy zinc rich primer to

Providing and applying Anti corrosive treatment to reinforcement as per

Providing Polymer modified cement Mortar treatment after removing of

Removing Manglore tiled roof and ridge tiles with battens, ridge and

Removing planking from roof or ceiling and stacking them same directed with

Removing the tar or coba and disposing of the material as directed etc.

Providing and fixing Burma Teak wood planking of 25 mm thk for

Providing and fixing Well Seasoned Burma Teakwood Eaves Board of design

Providing anti termite treatment to joints of wooden beam/joists used for the

Providing and fixing colour coated Zincalume(R) AZ150 (min 150gms/sq.mt.

Providing and applying two coats of bitumen to roof on new dungaree cloth

Providing and fixing Mangalore tiled roofing with class "AA" tiles including

Providing and fixing Mangalore type ridge & hip tiles class "AA" tiles including

Providing and laying lead flashing of best quality of 400 mm or more width as

Disconnecting, shifting, turning and removing Water Tank for repairs and

Removing brick bat coba including stacking the spoils as directed with all

Waterproofing the terrace slabs with average 100 mm thick, brick bats laid in

Providing and applying water proofing treatment using acrylic polymer

Providing and laying jointless Polydee-LM, a highly flexible elastometric

Supplying and Fixing 100 mm internal dia. 4.0 mm thk. (weight approx.10.0

Providing and fixing H.D.P. container one piece moulded water tabk made out

Providing sills of polished Kadappa stone 25mm to 30mm thick, on a bed of

Dismantling brick masonry in lime or cement mortar and stacking the

Removing the existing cement/lime plaster of any thickness without causing

Removing ventilators and small windows with frame the materials with all

Removing wooden or A.C. partition including frame work and stacking the

Lowering down the debris obtained from breaking and removing the cement

Dismantling flat wooden or A.C. Sheet ceiling with frame work including

Removing teakwood trellies work with frame including stacking the materials

Removing urinal pans or wash hand basins with frame including disconnecting

Removing W.C.pans including disconnecting the sanitary and water supply

Removing cast iron or wrought iron or A.C.pipe and stacking them as directed

Dismantling / Shifting and relocating the existing furniture including storage

Dismantling and removing existing plumbing fittings for all the wet areas and

Gently cleaning the surface of stone masonry and piers with specialized water

Extra over above item for additional treatment of poulticing for desalination

Specialised removal of layers of paint and other impervious coatings and

Removal of plant/ficus growth by pulling out root system embedded in

Dutchman Repair of stone sections that are severely distressed, re-installation

Dutchman Repair of stone sections that are severely distressed, re-installation

Lime Plastic repair and restoration of profile of weathered or damaged

Raking out cement pointing or any other hard material used and careful re-

Providing and applying an impregnating sealer such as SS–ProtectoSeal SB or

Providing and applying water proof coating to the concrete surface to resist

Providing and fixing weathershade of well seasoned good quality teak wood

Providing and fixing lightening conductor system comprising of erecting Air

Providing and fixing copper strip 25mm wide and 3mm thick for lightening

Providing lime plaster 45mm. Thk in two coats having backing coat of 20 mm.

Providing lime plaster 30mm. thk in two coats having backing coat of 20 mm.

Providing lime plaster 20 mm. Thk in two coats having backing coat of 20 mm.

Providing autoclaved aerated concrete block masonary of conforming to

Providing autoclaved aerated concrete block masonary of conforming to

Providing internal cement plaster 12mm thick in single coat in cement mortar

Providing internal cement plaster 20mm. Thick in Single coats in cement

Drilling and boring through 600mm thick masonry walls (horizontal/ angular)

Cleaning and polishing of existing Black Basalt stone flooring as indicated by

Replacing damaged, broken or missing Black Basalt flooring with 25-30mm thk

Cleaning and polishing of existing white marble found on existing rooms as

Replacing damaged, broken or missing flooring with 20-25mm thk Indian

Providing wax polishing to floors and dado, preparing the surface, scaffolding

Careful dismantling of the existing timber railing with the timber parapet upto

Providing and fixing or replacing damaged teak wood with well seasoned

Providing and fixing well seasoned Burma Teakwood balusters of size upto

Providing and fixing well seasoned Burma Teakwood handrail 100 - 150mm

Providing and fixing or restoring well seasoned Burma Teakwood Newel Post

Providing and applying plaster/wall punning with plaster of paris (with Plaster

Providing and applying one priming coat on concrete/masonry/Asbestos

Providing and applying interior wall finish luster of approved make on internal

Removing old paint from steel and other metal surface and making the

Careful painting of cast iron brackets, railings and balusters after cleaning,

Providing and applying melamine polish of required finish to the wood work

Polyurethene wood coating matt finish of Sirca make after preparing the

Providing and applying priming coat over new/old steel and other metal

Providing and applying two coats of synthetic enamel paint of approved

Providing and fixing unfinished ply partition arched / rectangular with an

Over and above Item , Providing and fixing panelling in well seasoned

Over and above Item Providing & fixing on one side 3mm thk. veneer on an

Providing and assembling 4" thick partition arched / rectangular Framework to

Providing & fixing on one side 19mm thk. Commercial Ply whereever required

Providing and fixing 12mm Gypsum board cladding to walls, plywood etc.

Providing & fixing 9mm thk. gypboard sheet on unfinished ply partition. The

Providing and fixing full height gyp partition with necessary cutouts as

Providing & fixing 10mm thk toughened clear float glass as partition (upto

Providing and fixing 10 mm thick toughened float Glass over a back surface of

Providing and fixing vinyl prints of high resolution images and to be pasted or

Providing and fixing flex prints of high resolution images , text , graphics and

Providing & fixing 12mm thick toughened clear float glass partition as per

Providing & fixing 12mm thick toughened frosted float glass partition as per

Providing and fixing well seasoned Burma teak wood skirting 20 mm thick in

Providing and fixing well seasoned Burma Teakwood Top Rail out of 105 mm x

Providing and fixing well seasoned Burma Teakwood chair rail out of 60 mm x

Providing and erecting free standing vertical partitions of existing historic

Providing and fixing well seasoned BTC wainscoting 38 mm thick with wooden

Providing leak proof treatment by Injection grouting method to old floor

Providing water proof bedding for flooring of Bath and WC 25 mm thick in

Providing water proof plaster in W.C. and bath 12mm thick for dado in cement

Providing water proofing in W.C. and bath including brick bat coba in all

Providng and Fixing 150mm x 150mm porcelain wall / dado & flooring tiles for

Providng and Fixing wall / dado rectangular tiles of 40mm wide plain colour in

Providing and fixing Stainless Steel 1.5mm (SS304) in the form sheets,

Providing & fixing lacquered glass 12mm thk. urinal partitions of 600 mm wide

Providing sills of polished Kadappa stone 25 mm to 30 mm thick, on a bed of

Providing and fixing Granite Counter size shown on architect's drawing,

Providing and fixing white glazed urinal of size 710 x 460 x 300 mm with

Providing and fixing wall hung white wash basin of size 550 x 400 x 195 mm

Providing and fixing white european type wall hung pan, of size 350mm x

Providing and Fixing toilet set for differently Abled persons consist of Floor

Providing and fixing concealed flush tank of approved make as directed by the

Providing and fixing bathroom accessories of Kohler or approved make

Providing and fixing Chromium Plated Toilet Paper Holder of Kohler or

Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and

Providing and fixing 15 mm diameter PVC Aqua kraft type of approved make

Providing and fixing C.P. 2 Way BIB cock with wall flange of approved make

Providing and fixing CP fittings of approved make including all plumbing

Providing and fixing antique bevelled edge mirror 15mm thick panels with a

Providing and fixing faucet jet spray of "Jaquar" or equivalent with 1m long

Providing and fixing Chrome Finish Concealed Stop Cock of "Jaquar" or

Removing doors and windows with frames and stacking the materials as

Providing and fixing or replacing damaged teak wood with well seasoned

Providing / fixing / restoring damaged teak wood with well seasoned BTC

Providing and fixing or replacing damaged teak wood with well seasoned

Providing and fixing or replacing damaged teak wood with well seasoned

Provision and fixing of new well seasoned glazed BTC timber fanlights in

Provision and fixing of new well seasoned BTC fanlights in pointed arches with

Existing doors to be removed and repaired and refitted as and when

Providing and fixing glazing of clear glass of Asahi, Modi, Saint Gobain or

Providing and fixing heavy duty decorative type brass hardware as per existing

Refurbishing existing heritage storage cabinets of from 450-460mm of depth

Refurbishing existing heritage storage cabinets of 300mm of depth and

Refurbishing existing heritage catalouge cabinets of 1140x690x1320mm

Refurbishing existing heritage catalouge cabinets of 900x340x770mm of width

Refurbishing existing heritage Glazed Display cabinets / of 450mm of width

Refurbishing existing heritage decorative Glazed Library Display cabinets of

Refurbishing existing heritage decorative mirror Vitrine / stand of 330mm

Refurbishing the existing wooden chairs / bench without arm rests as

Refurbishing the existing semi-circular wooden chairs / bench with arm rests

Refurbishing the existing wooden chairs with arm rests and leather cushioned

Refurbishing the existing wooden chairs / bench with arm rests and jute

Refurbishing the existing wooden chairs / bench with arm rests and jute

Refurbishing the existing wooden chairs / bench with arm rests as indicated as

Refurbishing the existing 1st floor lecture room wooden bench 355mm wide

Refurbishing the existing Dean's wooden desk with drawers / shutters as

Refurbishing the existing Department Head's wooden desk with drawers /

Refurbishing the existing Labratory wooden table with shutters as indicated

Refurbishing the existing Labratory wooden table with shutters as indicated

Refurbishing the existing Labratory wooden table with shutters as indicated

Refurbishing the existing Labratory wooden table with shutters as indicated

Refurbishing the existing wooden desk with drawers and above with Pigeon

Refurbishing the existing wooden desk with one side 3 drawers and other side

Refurbishing the existing wooden desk having one drawer on either side as

Refurbishing the existing Lecture hall wooden desk as indicated by architect,

Restoration of existing Podium and other platforms in teak wood of required

Providing and fixing 2400mm long 3-seater sofa having an upholstered seat

Providing and fixing 1800mm long 2-seater sofa/chaise lounge having a fully

Providing and fixing upto 700mm long single seater sofa having an

Providing Executive Swivel Chairs for Dean / College head or equivalent having

Providing & Arrangemnt of High Back Chair-TILT MECHANISM WITH

Providing & Arrangemnt of Mid Back, Normal Syncro Mechanism, Fixed

Providing & Arrangemnt of MidBack, ECOCTS Mechanism, Fixed Armrest,

Providing single chair with arms for conference / visitor of size 500mm x

Providing single chair with arms for conference / visitor of size 500mm x

Providing single chair with arms for conference / visitor of size 500mm x

Providing single chair semicircular with arms for visitor / reading of size

Providing single chair with arms for visitor / reading of size 490mm x 460mm x

Providing swivel bar stool of size 400mm x 750mm high which shall be

Providing and fixing rectangular executive workstations 800 mm height to be

Providing and fixing rectangular workstations 750 mm height to be made in

Providing and fixing rectangular workstations 750 mm height to be made in

Providing and placing the side tables/teepoy's of 15"x 15" upto a height of 18"

Providing and fixing a Console table of size 1500mm X 750mm X450mm with

Providing and fixing well seasoned Burma Teak Wood Storage Credenza 450

Providing and fixing BTC large discussion table of 1250mm x 2500mm x

Providing & fixing a 'U'- shaped conference table to be used in Halls in

Providing and fixing well seasoned B.T.C. Storage of size 450mm deep as per

Providing and fixing well seasoned B.T.C. Storage of 450mm deep as per

Providing and fixing well seasoned B.T.C. Book Shelf of 310mm deep as per

Providing and fixing overhead cabinet 450 mm deep to be made using 19mm

Godrej make compactor set PUSH PULL with ventilating façade including

Providing & fixing roller blinds of Vista Levelor make (Shade SN -301) or an

Providing & fixing black out roller blinds of Vista Levelor make (EP - 001) or an

Providing & fixing Vista levelor or equivalent make Motors & Remotes for

Providing and laying Carpet, of required width, design and colour as directed,

Providing & fixing 12mm thk. Soft board panelling with fabric on 12mm thk

Providing & Fixing in position, Acoustical Panelling made from Wood-wool

Providing and fixing wall fabric of silk damask range as approved by the

Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick

Providing and fixing TW 38mm X 12mm decorative beading with polish

Providing and fixing 12mm X 12mm beading with polish

Provision and fixing of well seasoned Burma teakwood Signage plaque to be

Providing and fixing clear 12 mm thk toughened glass 2 panels of size 750 mm

Provision and fixing of new C.P Teak wood notice boards and display boards

Providing and fixing 40mm - 75 mm Individual cut brass letters around upto 5

Providing and fixing Sunboard laminated signage panels of necessary size and

Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with

Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with

Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with

Supplying & erecting gun metal gate valve of size 15 mm dia complete as per

Supplying & erecting gun metal gate valve of size 20 mm dia complete as per

Supplying & erecting gun metal gate valve of size 25 mm dia complete as per

Providing and laying cast iron pipes of B class of 100mm diameter with

C.I.100*75*300 long arm (wt. 6kg)nahani trap

Providing and layingin trenches 50mm dai. uPVC pipe including necessary

P.V.C. 75 mm Soil Pipe 6 Kg/cm2 Pressure

Providing, laying and fixing, jointing Eco-drain 110mm SN8Nu-Drain Upvc

Dismantling / Shifting and relocating the existing furniture including storage

Providing sand faced plaster externally in cement mortar using approved

Cleaning and polishing of existing natural stone flooring like shahabad/

Providing and laying handcut polished Kotah Stone flooring 25mm to 30mm

Providing and laying Polished Shahabad Stone flooring 25mm to 30mm thick

Providing and applying French polish for required finish on previously polished

Dismantling RCC, Brickwork, Doors/windows, Steel, trusses, plinths, Timber,

Dismantling / Shifting and relocating the existing furniture including storage

Providing and laying machine cut machine Polished Kota stone flooring 25mm

Providing leather finished polishing to Kota/Marble/Shahabad/Kadappa Stone

Providing 25mm to 30mm thick partition of polished black kadappa stone slab

Providing and laying vitrified matt finish tiles having size 590mm to 605mm x

Providing and fixing wall mixer with overhead shower, shower arm, hand

Providing and fixing Chromium Plated wall mounted robe hooks of "Jaquar" or

Providing and fixing in vertical position telescopic M.S.prop under deflected

Crack stitching 6mm Helibar: Providing and fixing of Helifix Hi-fin

Crack stitching 8mm Helibar: Providing and fixing of Helifix Hi-fin

Crack stitching 10mm Helibar: Providing and fixing of Helifix Hi-fin

Creating HeliBeam with twin 6mm Helibars: Providing and fixing of Helifix Hi-

Pinning with CemTie 8mm (SS 304) : Providing and fixing of Helifix Hi-Fin

CrackBond TE 250ml : Providing & fixing of CrackBond TE 250ml an injectable

Polyplus SF: Providing and filling of general purpose styrene free resin with

Waterproofing the terrace slabs with average 100 mm thick, brick bats laid in

Dismantling / Shifting and relocating the existing furniture including storage

Providing and laying Historic Porcelain Tile of size 100mm high for border tiles

Removal of all existing paint and/or polish layers from handrail, newel post,

Removing doors and windows of any size and type, without frame mild

Providing and fixing or replacing damaged teak wood with well seasoned

Providing and Fixing MS Safety grill of weight 20 to 25 kg / sqm for windows

Solid Core Flush door Single leaf Providing and fixing factory made solid core

Providing waterproof plaster in W.C. and bath 20mm thick for dado in cement

Supplying and fixing - Linear WORKSTATION of Featherlite or equivalent make-

Providing solid wood " READING TABLE " of size 1200mm x 3000mm, 750mm

Fixing only Old B.T.C wood plank ceiling 25 mm thick planed on the underside,

Providing and fixing Mangalore tiled roofing with class 'AA' tiles including

Electrical Work

Supplying and laying HMS PVC Conduit FRLS grade 25 mm dia with necessary accessories in RCC work /false ceiling /false flooring as per specificationNo. WG-MA/CC.

Supplying and laying HMS PVC conduit FRLS grade 32 mm dia. With necessary accessories in RCC work/false ceiling/ false flooring as per specification No. WG-MA/CC.

Supplying and erecting 20mm dia. corrugated flexible polypropylene conduit

Supplying and erecting 25 mm dia. corrugated flexible polypropylene conduit

Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. With PVC accessories on wall /ceiling as per specification No: WG-MA/CON.

Supplying and erecting HMS PVC conduit FRLS grade 32 mm dia. With PVC accessories on wall / ceiling as per specification No: WG-MA/CON.

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 20 mm with accessories on wall/ceiling as per specification No: WG-MA/CON.

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25 mm with accessories on wall/ceiling as per specification No: WG-MA/CON.

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 32 mm with accessories on wall/ceiling as per specification No: WG-MA/CON.

Supplying and erecting PVC box trunking of size 50x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying and erecting PVC box trunking of size 75x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying and erecting PVC box trunking of size 100x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX

Supplying and erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 1x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW (Earthing)

Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 3x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting PVC insulated PVC round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Supplying and erecting PVC insulated PVC round sheathed 2.5sq.mm (30no.x 0.25mmdia.)3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Supplying 16 amp. 3 pin plug Top bakelite type of 230 V. A.C. supply.

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16A duly erected on provided plate and box with wiring connections complete

Supplying and erecting modular type bell-push 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16 / 20 A with indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type D.P. switch 32A with indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type T.V. socket single outlet, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type computer Jack RJ45 with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type bell indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type buzzer 220 / 250V, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete

Supplying and erecting modular type blanking plate one module, duly erected on provided plate & box.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 1 module complete duly erected.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 2 module duly erected.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 module duly erected.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 module duly erected.

Supplying and erecting PVC Surface modular switch box with doublemounting plate for 6 module duly erected.

Supplying and erecting PVC Surface modular switch box with double mounting & front plate for 8 module complete duly connected.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 12 module duly erected.

Supplying and erecting modular pop up Box 8 module erected with provided AV/ HDMI , RJ 45,6 A electrical sockets and switch on provided table.

Point wiring for light/bell/exhaust fan in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WGPW/ SW.

Point wiring for ceiling fan in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW (10 mtr long point)

Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW (12 mtr long point)

Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW (14 mtr long point)

Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW (16 mtr long point)

Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW (18 mtr long point)

Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW(8 mtr long point)

Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW(12 MTR LONG POINT)

Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW(14 MTR LONG POINT)

Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW(16 MTR LONG POINT)

Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW(18 MTR LONG POINT)

Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW(20 MTR LONG POINT)

Secondary point wiring for additional light/ bell point, concealed type in min 20 mm FRLS grade PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires with required accessories as per specification No: WG-PW/CW

Secondary point wiring for additional light/ bell point in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire with required accessories as per specification No: WG-PW/SW

Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification No: WGPW/ CW

Supplying & erecting 4 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforming to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW

Supplying & erecting 50 pair, 0.5mm dia, jelly filled unarmoured telephone copper cable with poly-al laminate moisture barrier, laid in provided PVC casing capping/conduit as per specification No. WG-TW

Supplying & erecting 100 pair, 0.5mm dia, jelly filled unarmoured telephone copper cable with poly-al laminate moisture barrier, laid in provided PVC casing capping/conduit as per specification No. WG-TW

Supplying & erecting 10 pair, 0.5 mm dia. jelly filled armoured telephone copper cable with poly-al laminate moisture barrier, polythene sheathed, G.S.Tape armoured polythene jacketed having laid in provided trench as per specification No. WG-TW

Supplying & erecting 20 pair, 0.5 mm dia. jelly filled armoured telephone copper cable with poly-al laminate moisture barrier, polythene sheathed, G.S.Tape armoured polythene jacketed having laid in provided trench as per specification No. WG-TW

Supplying & erecting co-axial copper cable low voltage grade tri-shielded RG- 6 as per specification No. WG-TW

Supplying and erecting 10m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete.

Supplying and erecting 15m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete.

Supplying, erecting & commissioning MDF Box 50x50 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW

Supplying, erecting & commissioning MDF Box 100x100 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW

Supplying, erecting & commissioning 10 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW

Supplying, erecting & commissioning 30 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW

Supplying, erecting & commissioning 100 pairs M.S. junction box made from min. 1.5mm thick MS sheet as per specification no. WG-TW

Supplying, erecting & commissioning 10 pair module for connection & disconnection of telephone cable as per specification no. WG-TW

Supplying, installing, testing & commissioning digital (hybrid) type EPABX of 6 x 16 extension complete.

Supplying and installing, testing & commissioning of digital (hybrid) type EPABX of 6 x 32 extensions suitable upto 96 extensions complete.

Supplying, installing, testing & commissioning push button telephone instrument desk top unit as per specification complete

Supplying, installing, testing & commissioning IP telephone instrument as per specification complete.

Supplying and installing cat-6 cable suitable for networking as per specification no. WG-COC/NC

Supplying and erecting LSZH armoured multimode optical fibre cable with 6 fibres, core dia 50/125 μm (OM3), suitable upto 10 GBPS, ethernet distance at 850 nm of wavelength, on wall/ceiling or laid in provided pipe/trench as per specification no. WG-COC/OFC LSZH

Supplying and fixing 2 m UTP patch cord of cat 6 type in position as per specification No. WG-COC/PC

Supplying, fixing, and configuring 8-ports managed gigabit, Layer-2 switch, 10/100/1000 base-T, POE smart switch plus 2 SFP erected in provided rack complete

Supplying, fixing, and configuring 24 ports, POE switch in provided rack as per specification No. WG-NWC/ENS

Supplying, fixing, and configuring 24 ports with 4 (SFP+) port, ethernet managed switch with web view/CLI, 6KV surge protection on ethernet port and console port for management in provided rack as per specification no. WGNWC/ GBS

Supplying, fixing, and configuring broadband ADSL router with all accessories, on provided rack as per specification No. WG-NWC/ADSL

Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP

Supplying and fixing SC/LC type multimode pigtails (OM3) for LIU to terminate OFC in LIU as per specification No. WG-NAS/LIU2

Supplying and fixing 6U wall mount rack (Dimension-DxWxH – 500x600x367 mm) as per specification No. WG-NAS/RAK

Supplying and fixing 12U wall mount rack (Dimension-DxWxH – 500x600x635 mm) as per specification No. WG-NAS/RAK

Supply, erection of Waterproof 3-Module Plastic Gang Box with 6 Amp Switch & Socket Shockproof IP55 Enclosure

Dismantling and removing existing electrical fitting and wires, exhaust fans and related electrical items as directed by the architect / engineer in-charge. All the original fixtures to be dismantled carefully from their location and stacking the same carefully so as to not cause any damage to the fitting and to be reused as required and indicated by the architect / engineer in-charge. Mode of Measurement: To be paid per room.

Supplying and erecting LED square / circular Max. 25 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2750 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED Strip light 5m Length Max. 45 W IP65 class having minimum lumens output of 800 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, p.f. >0.95, operating range of 230-270V, Life class of 30,000 Hrs. at L70B50, including driver with 1 year warranty

Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying and erecting regular/ standard model ceiling fan of 600mm. Sweep complete erected in position as per specification no. FG-FN/CF

Supplying and erecting regular/ standard model ceiling fan of 900 /1050 mm. sweep complete erected in position as per specification no. FG-FN/CF

Supplying and erecting exhaust fan heavy duty 230 V A.C. 50 cycles 375/380 mm. 1400 RPM complete erected in position as per specification no. FGFN/ EXF

Supplying and erecting energy saving ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Supplying and erecting fan clamp of 30 x 5 mm. M.S. flat of required length and 10 mm. M.S. bolt and nuts erected with necessary hook of 10 mm. M.S. round bar and painted.

Supplying and erecting ‘B’ class G.I .pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire.

Supplying and erecting 6W Reading Light with driver as per approved by architect / engineer in-charge

SITC of high-quality Mono Color Neon Flexible light, Protection Rating: IP65, Mounting Structure: Adjustable wall mount SS clips for fixing the lights. Power consumption:10W, CCT:3000k, (as per the design approval) BeamAngle:120º ,Power Input: DC 24V with external driver, Surge Protection: Inbuilt surge protection 2KV-4KV (Additional if required will be added as per the requirement),Fixture will be suitable to operate in a temperature range of 0°C to 50°C,LED life time should be at least 50,000 burning hours at L70 at 25 degree centigrade .Luminaire is inclusive of Integralmale /female water proof connectors with structures in prewired conditions as per IS standard. Engineer or 3rd party testing laboratory approval.

SITC of Aluminium Profile for Neon flex

Supply and erection of Track mounted LED Spot light of 15W luminous flux of luminaire 1500lm with Driver as per architect / engineer in-charge approved complete.

Supply and erection of 1 meter length of 35 mm x 15 mm size suitable for track light upto 20 W LED Luminary Diecast aluminium body IP67 Protection and suitable to operate on single phase 50Hz,230Volts AC supply

Supply and erection of 36W LED Linear hanging light length of 1200mm with CCT up to 6500K fixture including driver and required accessories complete.

Supply and erection of 50W LED Linear hanging light length of 1200mm with CCT up to 6500K fixture including driver and required accessories complete.

SITC of Chandelier Having antique Brass finish size of max 1 M dia. erarrangement of 8 Lights LED bulb Suitable of E12/E17/B22/E27 as per approved by architect / engineer in-charge.

SITC of Chandelier Having antique Brass finish size max 1.8 M dia. arrangement of 12 Lights LED bulb Suitable of E12/E17/B22/E27 with 2 rings as per approved by architect / engineer in-charge.

SITC of high-quality long throw mono color wash light, Protection Rating: IP66, complying to BIS standard " IS10322 (Part5/Sec1):2012 "and having CE certification against standard "Low Voltage Directive &Protective Equipment-EN60598- 1:2015 ", and " Electromagnetic Compatibility Directive-EN61547:2009", Mounting Structure: Adjustable surface mount yoke arrangements for fixing the light shaving the rotation degree embossed in the die cast. Power consumption: 100 W, CCT:1800K/3000K/4000K/6000K, (as per the design approval), Optics: PMMA with holder, Beam Angle: 15º/25º/45º/60º, Control: ON/OFF, Body: Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution: Optics Designed to minimize hot spots & fringing indifferent applications. Power Input: Constant DC24V with external driver, Surge Protection: Inbuilt surge protection in the driver 2KV-4KV (Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK07, Painting: Chemical3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°Cto 50°C,The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integralmale /female water proof connectors with structures in prewired conditions as per IS standard. PCB thickness must be 1.6mm, 35-micron Copper,2 WTC with Black or White masking, Copper /OSP finish. LM 79, IK07, IP66, HV Certificates from NABLA credited laboratory. Engineer or 3rd party testing laboratory approval. Power Loop In/Out along with IP67 connector having the length>300mm.

SITC of high quality long through mono color wash light, Protection Rating: IP66, complying to BIS standard"IS10322 (Part5/Sec1):2012" and having CE certification against standard" Low Voltage Directive & Protective Equipment-EN60598-1:2015", and" Electromagnetic Compatibility Directive-EN61547:2009", Mounting Structure: Adjustable surface mount yoke arrangements for fixing the light shaving the rotation degrees embossed in the diecast. Power consumption:50W, CCT:1800K/3000K/4000K/6000K, (as per the design approval), Optics: PMMA withholder, Beam Angle:15º/25º/45º/60º, Control: ON/OFF, Body: Die casted / extruded aluminium with embossed manufacture logo, Hotspot and light distribution: Optics Designed to minimize hotspots & fringing in different applications. Power Input: Constant DC24V with external driver, Surge Protection: Inbuilt surge protection in the driver 2KV-4KV (Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection upto IK07, Painting: Chemical 3/7 tank processed treatment before the powder coat black/ash /approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, the light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connect or swith structure sin pre wired condition s as per IS standard. PCB thickness must be 1.6mm, 35micron Copper,2WTCwithBlackor White masking, Copper/OSP finish. LM79, IK07, IP66, HV Certificates from NABLA credited laboratory. Engineer or 3rd party testing laboratory approval. Power Loop In /Out along with IP67 connector having the length>300mm.

SITC of 17 W Mono color Projector Spot light, Protection Rating: IP66, complying to BIS standard"IS10322(Part5/Sec1):2012"and having CE certification against standard " Low Voltage Directive & Protective Equipment-EN60598-1:2015 ", and " Electromagnetic Compatibility Directive-EN61547:2009", Mounting Structure: Adjustable wall mount yoke arrangements for fixing the lights. Power consumption:17W, CCT:1800/3000/ 4000/ 6000K, (as per the design approval) Optics: PMMA with holder, Beam Angle:15º/25º/45º/60º, Control: ON/ OFF, Body: Die casted/ extruded aluminium with embossed manufacturer logo, Hotspot and light distribution: Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input: DC24V (External Driver) or AC110-230V,50Hz. Surge Protection: Inbuilt surge protection 2KV-4KV (Additional if required will be added as per the requirement), Glare: Specially designed glare free round shape 360 deg/3 unit. Focus sing area /LED will be kept 90 Deg perpendicular below the glare free optic. Size of the LED optic& glare unit must be equal or +/-2% higher to achieve the maximum intensity and less glare. This additional arrangement can be fixed or removed on the application. Glare free optical design for human viewing angle from a distance within 2-3Mtr. Toughened transparent glass having the IK protection up to IK05 sealed above the glare free unit. Painting: Chemical 3/7 tank processed treatment before the powder coat black/ ash/ approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, LED life should be at least 50,000 burning hours at L70 at 25 degree centigrade. Luminaire is inclusive of Integral male/female water proof connectors with structure sin prewired conditions as per IS standard. PCB thickness must be 1.6mm, 35-micron Copper,2WTCwithBlackor White masking, Copper /OSP finish. LM79, IK05, IP66, HV Certificates from NABLA accredited laboratory. Engineer or 3rd party testing laboratory approval.

SITC of GI Cage for light protection, GI Cage made of mesh with back openable door and suitable hinges, light fixing provision with bolting option, base concrete foundation.

SITC of DC power driver for the above Lights, Power: 200W, Input: AC 110-240V AC, 50Hz, Output: DC 12/24V, Protection rating, IP67, Surge protection: LL 4KV, LE 6KV

SITC of IP65 "I" power connectors having 3/4 pole cable connector, chuck type strain relief, Current rating 20 A rms continuous, Easy and extremely precise locking system "Quick Lock" High impact materials - long-lasting and reliable

SITC of IP driver box made up of PVC / UPVC and ivory connectors for the internal terminations and external outgoing connecting points, fiber / brass glands of suitable size fitted MCB control for outgoing circuits.

Supply and fixing of 300 mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall.

Supplying and erecting midget type 3.0 litres instant type water heater of rustproof & shockproof ABS plastic body, high grade SS inner tank & 3kW heating element with corrosion & hard water protection, with minimum 3 safety protections (i.e. thermostat & thermal cut-out, function valve) complete with 6.5 bar pressure withstanding capacity 230/250V, 50Hz, A.C. supply with inlet and outlet, with 3 core PVC flexible copper wire leads duly tested and marking sr. no. and date of erection complete

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.0TR to 1.2TR capacity having ISEER minimum 5.00 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation&temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. APAC/ WAC

Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 12mm complete.

Supplying & erecting seamless outside & inside, smooth, dry and cleancopper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 16mm complete.

Supplying and erecting ultra violet storage type water purifier (RO+UV+UF) with softener for safe drinking water consisting of UV germicidal tube of 8W capacity choke made of copper wire and two indicator lamps with output of purified water minimum 0.33 litre/min with activated carbon filter and softener operating on 230V, single phase A.C. supply with UV fail & filter change indication system .(for TDS more than 200)

Supplying, erecting, testing and commissioning of 16HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete.

Supplying, erecting, testing and commissioning of 18HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/ digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete.

Supply, installation, testing and commissioning of VRF/VRV based Hi-wall type indoor unit (IDU) of nominal cooling capacity 0.6TR- 0.8TR ( 229 to 358 cfm) having EER as per BEE standards and specifications with multiple speed evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control with necessary controls, with 3-core copper flexible cord of required length and electrical terminal to receive power supply, etc. IDU shall have anti-corrosive coating suitable for coastal area. Unit shall be suitable for indoor wall mounting, having an electronic control console, provided with suitable mounting brackets with any additional refrigerant and oil charge as per the requirement during installation, connected to the system complete.

Supply, installation, testing and commissioning of VRF/VRV based Hi-wall type room/indoor unit (IDU) of nominal cooling capacity 1.0TR (358 cfm) to 1.25TR (417 cfm) having EER as per BEE standards and specifications with multiple speed evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, in built drain pump, expansion device, cordless remote control with necessary controls and electrical terminal to receive power supply, etc. IDU shall have anti-corrosive coating suitable for coastal area. Unit shall be of decorative slim dimension suitable indoor wall mounting. The indoor unit shall also have an electronic control console. The unit shall be suitable for wall mounting and provided with suitable mounting brackets with any additional refrigerant and oil charge as per requirement during installation complete.

Supply, installation, testing and commissioning of VRF/VRV based Hi-wall type indoor unit (IDU) of nominal cooling capacity 1.3TR (421 cfm) to 1.7TR (586 cfm) having EER as per BEE standards and specifications with multiple speed evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control with necessary controls, with 3-core copper flexible cord of required length and electrical terminal to receive power supply, etc. IDU shall have anticorrosive coating suitable for coastal area. Unit shall be suitable for indoor wall mounting, having an electronic control console, provided with suitable mounting brackets with any additional refrigerant and oil charge as per the requirement during installation, connected to the system complete.

Supply, installation, testing and commissioning of VRF/VRV based Hi-wall type indoor unit (IDU) of nominal cooling capacity 1.8TR (594 cfm) to2.2TR (655 cfm) having EER as per BEE standards and specifications withmultiple speed evaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control with necessary controls, with 3-core copper flexible cord of required length and electrical terminal to receive power supply, etc. IDU shall have anticorrosive coating suitable for coastal area. Unit shall be suitable for indoor wall mounting, having an electronic control console, provided with suitablemounting brackets with any additional refrigerant and oil charge as per the requirement during installation, connected to the system complete.

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact / standard size) of nominal cooling capacity 3.0TR (1100 cfm) to 3.2TR (1165 cfm) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact / standard size) of nominal cooling capacity 3.3TR (1165 cfm) to 4.0TR (1218 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation.

Supplying and erecting an air flow regulating valves/dampers in provided flexible or rigid duct/pipe of 100 mm size with an alteration for existing flexible PVC pipe duct and necessary joints, sealing, couplings at position complete.

Supplying and erecting an air flow regulating valves/dampers in provided flexible or rigid duct/pipe of 150 mm size with an alteration for existing flexible PVC pipe duct and necessary joints, sealing, couplings at position complete.

Supplying and erecting an air flow regulating valves/dampers in provided flexible or rigid duct / pipe of 200 mm size with an alteration for existing flexible PVC pipe duct and necessary joints, sealing, couplings at position complete.

Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.

Supply, installation, testing and commissioning wireless remote control having colour LCD panel, real time clock, temperature limitation (16 to 30° C, functions like filter clean reminder timer suitable to communicate with wired controller complete.

Supplying, erecting, testing and commissioning centralised programmable remote control panel (HMI) touch manager controls minimum 16 system of 64 ODU's can be controlled and up to 992 IDU's can be individually mounted and controlled indoor units having colour min 200mm size LCD touch panel, yearly schedule, power proportional distribution function, temperature limitation, history function complete erected on wall integrated with provided fire alarm system.

Supplying and installation of high pressure grade required size copper connection Y or T- Joints/refnet complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV/VRF air conditioning system.

Supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 41.3mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete.

Supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 34.9mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete.

supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 28.6mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations with OEM standards of VRV/VRF air conditioning system complete.

supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 22.2mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultraviolet radiation with OEM standards of VRV/VRF air conditioning system complete.

supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 19.1mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV/VRF air conditioning system complete.

supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 15.9 mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV/VRF air conditioning system complete.

supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 12.7mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV/VRF air conditioning system complete.

supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 9.5 mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV/VRF air conditioning system complete.

supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 6.4mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV/VRF air conditioning system complete.

Supply, Installation, Testing & Commissioning of charges along with topping-up of Eco Friendly with manufacturer recommended refrigerant.

Supply, Installation, Testing & Commissioning of Mini Aqua Condensate Drain Pump for hi-wall unit.

VENTILATION - Supply, Installation, Testing & Commissioning of ceilling Mounted circular inline Fan - 200 CFM

VENTILATION - Supply, Installation, Testing & Commissioning of ceilling Mounted circular inline Fan - 300 CFM

Supply, installation, testing and balancing of supply air and return Disc Valve in accordance with the approved shop drawings and specifications

ANTI CORROSION COATING Supply and application of the anticorrosive coating (condenser coil, refrigerant piping connections etc.) a. Anti corrosive chemical treatment with oil & Chemical mix to be coated in 3 coats. b. Evaporator coil should be completely coated with chemical and to be fixed again in Indoor unit. c. For outdoor unit, condenser coil and piping connections from coil to compressor should be coated with chemical and oil mix

LOADING AND UNLOADING CHARGES

Removal of existing Split AC units mounted on the walls as directed by the architect / engineer in-charges including all connections, copper piping, drains etc., from the site and stocking the same as directed by the client and as approved by Engineer in charge.

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 9 mm for AC system.

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 12 ways /phase (36 poles), with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 4 ways /12 Poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 8 ways /24 poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/4 pole MCCB as incomer & outgoing SP MCB (24 poles) or TP MCB of 8 ways (24 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Providing & erecting 4 Pole MCCB, 415 V, 63A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Providing & erecting 4 Pole MCCB 415V, 250A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB

Supplying, fixing and commissioning 2 pole, RCBO 6/10/16/20/25A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Supplying, fixing and commissioning 2 pole RCBO 32/40A, with overcurrent,rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Supplying, fixing and commissioning 4 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Providing & erecting floor/wall mounting, MCCB panel board, with door, suitable for four pole incoming 250A, 12 ways four pole outgoing, up to 100 A MCCBs on iron frame, as per specification no. SW-SWR/MCCBPB. (Excluding MCCBs)

Providing & erecting incoming and outgoing cable alleys suitable for MCCB panel board with door, 250A incoming and 12 way outgoing or 400A incoming and 6/8 way outgoing made from CRCA sheet 1.6 mm thick duly powder coated and having vertical insulated partition for shielding between the shared face of cableway and DB

Providing & erecting prewired meter module suitable for MCCB panel board with CTs and emfs VIF meter

Supplying and erecting terminal spreaders suitable for 4 pole, up to 100A MCCB (Set of 8)

Supplying and erecting terminal spreaders suitable for 4 pole, above 100A up to 250A MCCB (Set of 8)

Supplying and erecting extended rotary handle for MCCB with adjustable telescopic rod suitable for up to 250A MCCB.

SITC of Main Panel LT ,The panel shall be comprising of following & IEC 61439, Panel should be fully compartmentalized, floor mounted with M.S. Channel dully painted, fabricated of 14/16swg CRCA sheets completely derusted, chemically treated and powder coated with approved shade, ON - Off Indicating LED lamp, locking arrangements with dual source intelligent flush mounted panel meter three phase four wire (IPM) 415V CT/ PT site programmable class I flush mounted (96 x 96mm) meter with voltage, current, frequency, power factor, kWh .The material and the spacing of the Busbar supports should be same as per the type tested assembly. as per SLD having following items:- Main I/O 315 Amp 36kA FP MCCB with Rotary Handel including terminal spreaders Bus bar chamber TPN & E with aluminium bars 315A 36KA Outgoing- 160A TPN MCCB- 1 N0s. (for APFC Feeder) 100A TPN MCCB - 2 Nos. with Rotary Handel including terminal spreaders, 63A TPN MCB C series - 3 Nos. 40A TPN MCB C series - 8 Nos. 32A TPN MCB C-Series-7 Nos With 80 KVAR Rating APFC Panel as per SLD Approved.

SITC of Main Panel LT ,The panel shall be comprising of following & IEC 61439, Panel should be fully compartmentalized, floor mounted with M.S. Channel dully painted, fabricated of 14/16swg CRCA sheets completely derusted, chemically treated and powder coated with approved shade, ON - Off Indicating LED lamp, locking arrangements with dual source intelligent flush mounted panel meter three phase four wire (IPM) 415V CT/ PT site programmable class I flush mounted (96 x 96mm) meter with voltage, current, frequency, power factor, kWh .The material and the spacing of the Busbar supports should be same as per the type tested assembly. as per SLD having following items: Main I/O 160 Amp 36kA FP MCCB with Rotary Handel including terminal spreaders. Bus bar chamber TPN & E with aluminium bars 160A 36KA Outgoing- 100A TPN MCCB- 1 N0s. (for APFC Feeder) 100A TPN MCCB - 1 Nos. with Rotary Handel including terminal spreaders, 63A TPN MCB C series - 4 Nos. 40A TPN MCB C series - 4 Nos. 32A TPN MCB C-Series-7 Nos With 30 KVAR Rating APFC Panel as per SLD Approved.

Supply, erection of IP 65 waterproof 8-way PVC Enclosure with cover for AC Outdoor Unit.

SITC of Power Distribution Board made up of MS Sheet metal fabricated housing black powder coated and ivery connectors for the internal terminations and external outgoing connecting points, fibre / brass glands of suitable size fitted MCB control for outgoing circuits. - 12 Nos of 6/10A SP Outgoing MCB's. - 1No of 32A TPN Incoming MCB.

Supplying & erecting triple pole and neutral PPI distribution board (TPNDB), with 2P RCBO per Phase Isolation and SPMCB of 4 ways/phase (12 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral PPI distribution board (TPNDB), with 2P RCBO per Phase Isolation and SPMCB of 6 ways/phase (18 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral PPI distribution board (TPNDB), with 2P RCBO per Phase Isolation and SPMCB of 8 ways/phase (24 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral PPI distribution board (TPNDB), with 2P RCBO per Phase Isolation and SPMCB of 12 ways/phase (36 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority

Supplying and erecting bus bar chamber triple pole with neutral with four aluminium bars, 500V 300A having 40mm (Width) X 5 mm (Thickness), with 99.9 % aluminium purity as per E91E Grade & Current Density 0.8 A per sq. mm. compliance to IS 5082 and enclosure fabricated with 16 SWG CRCA sheet and epoxy paint, with suitable number of ways and with SMC/DMC Insulators and accessories of suitable rating complete as per specification no. CPBB

Supplying & erecting LED type indicating pilot lamp with LED colours red / yellow / green, 230 / 250V on provided box / panel with necessary material, wiring & connections etc.

Supplying & erecting LED type indicating pilot lamp with LED colour blue, 230 / 250 V on provided box / panel with necessary material, wiring & connections etc.

Supplying, erecting & terminating XLPE insulated unarmoured cable 1100 V 1 core 120 sq. mm. aluminium conductor complete erected with lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 50 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 70 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 120 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½core 240 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 300 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AT

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 90 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete

Providing & erecting hot dipped galvanised cover suitable for perforated type Cable tray manufactured from 18 SWG (1.2 mm thick) GI sheet of 150 mm width & 20 mm height complete with necessary hardware

Providing & erecting hot dipped galvanised cover suitable for perforated type Cable tray manufactured from 18 SWG (1.2 mm thick) GI sheet of 300 mm width & 20 mm height complete with necessary hardware.

Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting copper strip of high purity required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint with joints required. As per specification no. EAEP.

Supplying & erecting gun metal gate valve of size 15 mm dia complete as per specification no. FF-VL/GV

Supplying & erecting gun metal gate valve of size 20 mm dia complete as per specification no. FF-VL/GV

Supplying & erecting gun metal gate valve of size 25 mm dia complete as per specification no. FF-VL/GV

Supplying, installing, testing and commissioning FRLS, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU(Fire Cable)

Supplying, installing, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 1 loop capacity and capable of supporting upto 250 devices and detectors per loop, with on-board LCD display with min 16 lines of text, operating at 230 V 50 HZ - AC with inbuilt Battery Backup of a minimum 24 hours in normal conditionm and 30 min in alarm condition, suitable provision for network connectivity, interfacing with third party equipment via a MODBUS/ OPC/ L-ON interface etc. conforming to IS 15908:2021, IS 2189: 2008, EN 54 & VDS / FM/ UL 864 (10th edition) with 3 years replacement warranty FF-AFAS/CP.

Supplying, installing, testing and commissioning of addressable optical smoke detector, single/twin LED’s with 360 degree view, suitable for low voltage 15 to 32 V DC two wires supply, in-built locking mechanism to check the removal and pilferage of the detector, in built isolation mode, start up current 300μA and alarm condition current shall be maximum 6.5 mA, operating temperature 0°C to 50°C, humidity 0-95% RH, IP 41, conforming to IS 2189: 2008, 11360_1985_Reff2020 EN 54 or UL Approved with 3 years equipment replacement warranty FFAFAS/ SD .

Supplying, installing, testing and commissioning of addressable manual call points ( break glass type/pull station type), made of addressable break glass plastic square in shape surface/flush mounted with "Break Glass" massage embedded on the glass, complete erected with mounting base and required accessories conforming to EN 54 or UL listed with 3 years equipment replacement warranty FF-AFAS/MCP.

Supplying, installing, testing and commissioning of addressable fire isolator module complete as required. EN 54 /FM or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/ISM

Supplying, installing, testing and commissioning of addressable horn cumstrobe sound/ hooter, output frequency 500 to 1000 Hz with dB as per Chart given in IS 15908:2021, with flashing at 1 Hz over the strobe’s entire operating voltage range EN 54, conforming to IS 2189: 2008, IS 15908:2021 standards with 3 years equipment replacement warranty FF-AFAS/SSH.

Supplying, erecting, testing and commissioning 15 to 30 Watts sound column or ceiling mounted complete as per specification no. FF-PA/SOC(Tap to 10W)

Supplying, erecting, testing and commissioning of 1.5 sq. mm speaker wire complete

S u p p l y i n g & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

Supply & Erection ABC Type Powder type fire extinguisher as per IS 2878/15683 complete erected with necessary clamp made from 50x6 mm M.S flat nut & Bolts grouted in wall complete.

Supplying, erecting, testing and commissioning Public address and emergency sound system controller complying to international standard of emergency sound system with Built in 500W Amplifier (with following feature) a. Expandable up to 128 speaker lines; b. 10 contact trigger input; c. Dual channel audio capability; d. Auxiliary 2 channel Input

Supplying, erecting, testing and commissioning Call Station with built-in monitoring speaker and programmable buttons, Temporary recording function for instant message recording and broadcasting.

Making trench in hard murum/Tar road having 0.9 m depth and minimum 0.3mtr width for laying provided cables of voltage range 3.3 kV to 11 kV complete as per specification No. CW-EXN-CTR

Suppl, Installation, testing, commissioning of 2 MP Motorized Varifocal IP Based Dome Camera with Built in Microphone with having following feature Max 2M (1920x 1080) Resolution (IR LED On)

Supply, Installation, testing, commissioning of 2 MP Motorized Varifocal IP Based Bullet Camera with Built in with external Microphone with having following feature. Max 2M (1920x 1080) Resolution (IR LED On)

Supply, Installation, testing, commissioning of 32 Channel NVR with 4 SATA HDD without redundant Power Supply, record up to 32 video streamers, record up to 30 fps at full HD 1 resolution.

Supply, Installation testing, commissioning of 32 Channel NVR with 2 SATA HDD without redundant Power Supply, record up to 32 video streamers, record up to 30 fps at full HD 1 resolution.

Supply & Installation, Testing and Commissioning of 24x7 40-inch LED Display full HD 1920x1080 pixel display Wi-Fi & Internet accessible with 2USB and 2 HDMI Port with wiring interface

Savani Heritage Conservation Pvt Ltd (BID ID -6480699)