SPL REPAIR TO BLDG NO JP-15, JP-24, ML-05 (JCO MD ACCN) AND PROVN OF HARD STANDING WITH INTERLOCKING TILES IN JP LINE OF CITY AREA UNDER AGE B/R-I AT ALWAR

Amount

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified & directed.

M&L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (Old size bricks) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with FLY ASH brick straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified& directed.

Demolition of cement concrete (un-renforced) in ground floor and paving not exc. 15 cm thickness (below or above ground level) & removal of rubbish material complete all as specified & directed.

Demolition of cement concrete (un-renforced) in ground floor and paving exc. 15 cm thickness (below or above ground level) & removal of rubbish material complete all as specified & directed.

M&L PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate), 25mm thick, as in Sub base complete all as specified & directed.

M&L vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over with and including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

M&L vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade as approved), area of each tile not exceeding 0.36 sqm, in wall, dado, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over 10 mm thick rendring in cm 1:4 complete all as specified & directed.

M&L coloured non skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over with and including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed.

M&L non skid ceramic tiles colored 300x300x7mm thick in floor set and jointed in neat cement slurry and pointed in white or coloured cement laid over with and including 15mm thick screed bed in CM 1:6 complete all as specified & directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) , removing serviceable tiles to store and rubbish off the premises.

M&L glazed ceramic coloured tiles in vertical surface 450mm x 300mm x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles with and including 10 mm thick rendering in CM 1:4 complete all as specified & directed.

M&L machine cut kota stone slab flooring 18-20mm thick laid over with and including 20 mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified& directed.

M&L machine cut kota stone slab 18-20mm thick in steps for riser, dado, skirting, wall etc over 15 mm thick rendering in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified & directed.

M&L for cutting polishing of old kota stone surface complete all as specified and directed.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and over screed bed 20 mm thick CM 1:6 cement concrete complete all as specified.

M&L 50 mm thick PCC(1:3:6) type C1 (using 20mm graded stone aggregate ) as in plinth protection finished fair and even complete all as specified & directed.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc all as directed.

M&L rendering 10mm thick in cement mortar 1:6 on fair faces of stone/brick masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified.

M&L rendering 15mm thick in CM 1:4 on stone/brick wall surfaces or other than fair faces of brick work & surfaces finished even and smooth without using extra cement with water proof compound all as specified. (Water proofing compound shall be paid separately)

Supply only integral water proofing compound.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified.

M&L preparation of new plastered surfaces of walls and applying two coats of Oil bound distemper over a coat of 1 mm thick wall care putty of approved tint complete all as specified & directed.

M&L preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified & directed.

M&L preparation of new plastered surfaces of walls and applying two coat of cement base paint over one coat of primer of approved shade/tint complete all as specified & as directed.

M&L preparation of newly plastered surfaces & applying three coat of white wash on ceiling complete all as specified& directed.

M&L preparation of old decorated plastered surfaces of walls and applying one coat of cement base paint of approved shade/tint complete all as specified& directed.

M&L complete removal of existing treatment on walls applying two coats of oil bound distemper over a coat of 1mm thick wall care putty complete all as directed.

M&L preparation of old plastered surfaces of wall and applying one coat of white wash complete all as specified& directed.

M&L preparation of old plastered surfaces & applying one coat of white wash on ceiling complete all as specified& directed.

Preparation of old steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as directed.

Demolition of mud in roofs, any thicknes, including plastering , existing tretement and cleaning (whether full thickness removed or only or part there of) etc in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified & directed.

M&L Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 complete all as specified& directed.

M&L PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified& directed.

M&L rendering 15mm thick in CM 1:4 with water proofing compound over green concrete surface(WPC will be measured and paid seperately) surface finished even and smooth (without using extra lime or cement) complete all as specified& directed.

Preparation of roof top surface, providing and applying heat reflective UV stable single component smart care damp proof ultra is a fibre reinforced elastomeric liquid applied water water proofing membrane formulated with PU hybrid polymers and reinforcing acrylics fibre and having SRI of 106 on top of concrete roof surface in three coats incl self primer at ratio of damp proof and water 3:1 and coverage @ 1 Ltr/10 Sqm with a thickness of 650 micron. Note :- 6 Hrs interval between two coats will be maintain & the work will be carried out through company applicator duly get approved from Accepting officer in writing before incorpotion and paid only after receiving of the warrenty certificate from the company. Make:- Dr Fixit, Asian paint or equivalent as approved by GE.

Cutting openings through walls for door, window and other openings or enlarging existing openings, etc., or cutting out defective masonry for underpinning including providing, fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises.

Forming jambs, etc to openings (to foregoing item), with stone including cutting, toothings and properly bonding into old work built in CM 1:6, including facing and pointing (if necessary) to match existing work, complete all as specified& directed.

M&L 50mm thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in cement mortar 1:4,complete all as specified& directed.

Cutting holes in stone walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 exc half brick wall complete all as specified & directed.

Taking down Chowkatts or frames with shutters ( without taking off shutters from the frame) n exc 1.5 sq.each & removing to store.

Taking down Chowkatts or frames with shutters ( without taking off shutters from the frame exc 1.5 sq. m but n exc 4 sq m each & removing to store.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification.

M&L framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete & making good the floor in PCC 1:2:4 type B-0 to match the existing floor.Fe-410 (Gde-E250 quality A).

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintel hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps,plate washers and similar small articles conforming to Fe410-0 or Fe 310-0 complete all as specified & directed.

S&F 35mm thick 2nd class hard wood factory made panelled door shutter with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete all as specified & directed.

S&F 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified & directed.

M&L factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified & directed.

M&L preparation of new wooden surfaces over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified & directed.

S&F butt hinges 100mm long medium weight, colled rolled mild steel complete all as specified& directed.

S&F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified & directed.

S&F 150mm aluminium handles, cast type, anodised complete all as specified & directed.

S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified & directed.

S&F 300mm helical/rat tail door Spring 300mm size with MS sheet wing pattern including roller plate complete as directed.

S&F in repair stainless steel drapery rod 25mm dia (in lengths directed) of approved colour with and including decorative bowel at both ends and pair of power coated stainless steel brackets fixed at both ends with PVC rawl plug and steel screwed on walls/beam complete all as specified & directed.

S & F stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanized wire staples complete all as specified and directed.

S&F anodized aluminium frame and other sections for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed.

S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc. complete all as specified & as directed.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified & as directed.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium grill of approved pattern for windows/ ventilators/doors complete all as specified and directed.

S&F sheet glass ordinary quality, in squares n. exc 0.5 sqm each 4.80 mm thick complete as directed.

S&F door closer hydraulically regulated, designation No. 3, aluminium (Die cast) body, universal type (ISI marked) complete all as specified & as directed.

S&F in repair kitchen sink without draining board made out of stainless steel 1mm thick with plugs, washers and waste pipe including bedding in cement mortar to dwarf wall or including and fixing cast iron cantilever brackets and connecting union to pipe over all size 495 x 420mm bowl size 410x330x160 mm including flush pipe of polyethylene of low or high density or PVC 32mm bore with long screwed shanks and fly nuts complete all as specified & directed.

S&F in repair stainless steel plate rack, 1.00mm thick for kitchen size 600mm x 900mm x 230mm complete all as specified & directed.

S&F in repair PVC connection pipe, 15mm dia & 600mm long with adopter and washer at both end complete all as specified & directed.

S&F in repair Rotational moulded polyethylene water storage tanks of 500 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling water tanks complete all as specified& directed

S&F in repair ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 20 mm dia complete all as specified & directed.

S&F in repair brass Gun-metal, globe or gate valves 20mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking up or down 15mm steel tubing and connections, complete all as specified& directed.

Taking up or down 20mm steel tubing and connections, complete all as specified& directed.

S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed.

S&F steel tubing medium grade 20mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified & directed.

S&F in repair fancy type bib tap, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed omplete all as specified & directed.

S&F in repair white vitreous china wash hand basin 'Flat back' of size 550x400mm fixed on and including new brackets CP waste coupling and PVC Waste pipe complete all as directed.

S&F in repair 15mm dia CP pillar tap fancy type cast copper alloy, CP with capstan head, screwed down high pressure, with or without lettered 'HOT' or 'COLD' with long screwed shank and fly nuts screwed for iron pipe and fixed complete all as directed.

S&F in repair Stop/angle valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified & directed.

S&F in repair stop valves, fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia long sunk concealed type complete all as specified & directed.

S&F in repair towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as directed.

Cutting holes into or through brick but in brick walls built, in cement mortar or cement lime mortar and stone walls built in lime mortar or walls of lime exe 150 sqcm but n. exc 400 sqcm (not excluding 25CM depth) for cooler stand complete all as specified & directed.

S&F in repair vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe etc & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified & as directed.

S&F in repair vitreous China Squatting pan, Orissa pattern, size 580mm x 440mm white with integral foot rests connection to trap and to flushing pipe, etc. complete including making good to floor complete all as specified & directed.

S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe ) with PVC waste pipe complete all as specified.

S&F in repair PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC make Dolfine/Commander Champion complete all as specified.

S&F in repair PVC (SWR) pipes 110 mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors/wall complete all as specified & directed.

S&F in repair PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints laid in floor or fixed to walls complete all as specified & directed

S&F in repair PVC (SWR) bends any radius 110 mm bore complete all as specified & directed

S&F in repairs MS grating CP 100mm dia, with or without hole for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as directed.

S&F PVC (SWR) vent cowl 110mm complete all as specified & directed.

S&F in repair 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified & directed

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified & directed.

S&F in repair PVC (SWR),110mm junction single, (Single T) equal or unequal complete all as specified & directed.

M&L writing letters or figures (Block, Roman, Italic or Indian letter n.exc 30cm high) complete as directed.

S&F in repair brass chromium plated shower rose 125mm size with swivel joint type including fixing to steel pipe of 15mm bore or union complete all as specified.

Dismantling framed timber scantlings 40 sq. cm and over in section, in any position complete all as specified.

M&L plates (plain or chequered) channels. Square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe 410 W (Gde E-250) Quality B ,complete all as specified & directed.

S&F mild steel screw bolts dia of Neck 5mm to 10mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,exc 5cm but n exc 10cm long compleete all as directed.

M&L roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. Fe 410 W (Gde E-250) Quality B ,complete all as specified & directed.

Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed.

Dismantling asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified & directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws etc complete all as specified & directed.

M&L PCC Type D2 1:4:8 (40mm graded stone aggregate) Cement concrete in foundations, filling and mass-concrete complete all as specified & directed.

M&L PCC 1:3:6 type C1 using 20mm graded stone aggragate as in bed blocks, coping etc including weathering slightly rounded or chamfered angles and throating making grovves for fixing of man hole cover including necessary form work complete all as specified & directed.

M&L PCC (1:3:6) type C1 (using 20mm graded stone aggregates) in benching to manhole complete all as specified.

S&F 50mm thick steel fibre reinforced (SFRC) manhole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 3 ton /Sqm in square rectangular or Circular shape complete all as specified and directed.

M&L 75 mm thick PCC 1:4:8 type D -2 using 40 mm graded aggregate as in sub base of path/hardstanding complete all as specified & directed.

M&L chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with gray pigment cement and pigment with and including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) of any thickness, including cover fillets complete all as specified and directed.

M&L false ceiling with ArmGyp-FB ceiling tiles of 595mm x 595mm (as approved by GE) fixed with and including galvanised iron powder coated inverted "T" or "L" section (concealed GI frame work) of mettalic or equivalent suspended from ceiling with provn of galvanised wire 4 mm dia and wall taping screw including butterfly clip, hold down clips for fixing the board to frame complete all as per manufacurers instructions all as directed and specified. (a) size of main tee 39 x 24.4 x 0.8 mm (b) size of wall angle 22.2 x 22.2 x 0.65 mm (c) size of grid 0.61 x 0.61 mm complete all as specified & directed.

M&L preparation of old wooden surfaces over 10cm width or girth and applying one coat of synthetic enamal paint (of approved shade) complete all as specified & directed.

Excavation in post holes in soft loose soil (similar holes) each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers not exc 25cm, watering and removing surplus soil to a distance n exc 50m and making good surface complete all as directed.

M&L PCC type C2 1:3:6 (40 mm graded stone aggregate) cement concrete in foundations, filling and mass-concrete complete all as specified & directed.

M&L 60mm thick machine pressed precast conctete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006, M-35 Grade laid over with and including 25mm thick sand complete all as specified and as directed.

M&L sand for cushioning, interlocking tiles joint to be filled with sand, including spreading and levelling in layers n exc 25 mm thick complete all as specified and as directed.

M&L precast cement concrete solid block factory made kerb stone in PCC 1:2:4 type B-1 using (20 mm graded stone aggregates) set in CM 1:6 (size of precast concrete block complete all as specified & directed.

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep and getting out in soft/loose soil complete all as specified & directed.

Returning filling in incl spreading levelling watering and well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified & directed.

Removal of excavated material (soil) to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above or below the starting point complete all as specified & directed.

M&L reinforced concrete pipes, class NP2, laid and jointed complete with collars bore in pipe in 300mm complete all as specified and directed.

M&L hard core of broken stone or boulders of gauge n.exc. 63mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rolled/ rammed to a true surface complete all as specified and directed.

M&L 100mm thick PCC 1:4:8 type D -2 using 40mm graded aggregate as in sub base of path/hardstanding complete all as specified & directed.

M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-35 Grade with grey cement and no pigment complete all as specified and as directed.

M&L cement concrete (1:2:4) type B-1 using 20 mm graded aggregate as in coping over bricks works, water troughs and the like including weathering, slighty rounded all as spcecified & directed.

M&L for providing cement concrete 1:2:4 type B-2 concrete, using 40mm graded stone aggregate as in water throughs, surface channels and drains and benching including finishing the top of benching even and smooth using extra cement complete all as directed.

Taking down carefully copper/aluminium point wiring for one light /socket/power point and taking down of teak wood batten/ PVC casing caping and making good disturbed surfaces of walls/ ceiling/ floors etc including dismentling of fittings complete all as specified.

M&L point wiring for one light point controlled by one, one way switch with multistrand 1.5 Sqmm unsheathed copper conductor PVC insulated FRLS cable including continuous earth wire 1.5 Sqmm in green colour unsheathed copper conductor PVC insulated FRLS cable connected to common earth dolly in concealed PVC conduit 25 mm with accessories by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS in on New wooden boards fixed on wall for mounting switch, socket, regulators etc with and including 3mm thick phenolic laminated sheet top cover complete all as specified.

All as per serial item No 127.00 here-in-before but for one fan point controlled by one switch and regulator.

All as per serial item No 127.00 here-in-before but for one exhaust fan point controlled by one switch and regulator.

All as per serial item No 127.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board.

All as per serial item No 127.00 here-in-before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on independent board.

All as per serial item No 127.00 here-in-before but for one bell/buzzer point controlled by one bell push.

All as per serial item No 127.00 here-in-before but for one 3 pin socket outlet 15/16 Amps controlledby one 15/16 Amps switch on independent board with 2.50 Sqmm two single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour.

S&F switch piano flush type, single pole, one way, 5/6 Amp, 230 Volts complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 15 Amp, 230 Volts complete all as specified and directed.

S&F bell push flush type, 5 Amp, 240 Volts complete all as specified and directed.

S&F bell / buzzer AC 230 Volts, single pole complete all as specified and directed.

S&F socket outlet for 3 pin (with 2 pin outlet also), 5/6 Amp, flush type 240 Volt complete all as specified and directed.

S&F socket outlet for 2 in 1, 3 pin 5 & 15 Amp, flush type 240 Volt complete all as specified and directed.

S&F ceiling rose surface bakelite 65 x 50mm two or three terminals complete all as specified and directed.

S&F stepped type electronic fan regulator, flush type and connecting up ISI marked 240 volts complete all as specified & directed.

S&F decorative ultra slim liner LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient suitable for 16 Watt to 20 Watt with LED tube of model E-LITE LED Pride Plus and connecting up with and including three core, PVC insulated, sheathed copper conductore cable of required size and length from ceiling rose to fitting complete all as specified & directed.

S&F LED type street DRACO Series light luminaire 20 watt 230 V 50 Hz including all necessary fitting accessories and LED complete all as specified & directed.

S&F LED bulb 10/11 watt complete all as specified and directed.

S&F lamp holder PVC/Polycarbonatetype with back plate suitable forbatten fittings complete all as specified.

S&F sheet metal enclosures, double door type, suitable for fixing MCB SPN with 200 Amps rated bus bar, 8 way, 240 volts complete all as specified and directed.

S&F MCB 32/40 Amps, single pole & neutral, 240 Volts complete all as specified and directed.

S&F MCB 6-40 Amps, single pole, 240 Volts 'C' curve, 10KA ISI marked as per IS/IEC 60898-1 2002 complete all as specified and directed.

S&F 2nd class hard wood rectangular block open recessed of size 30 x 25 x 5cm depth with 3mm thick phenolic laminated sheet top cover fixed with suitable steel screws & PVC rawl plug (4 Nos), complete all as specified and directed.

Supply, laying, jointing and testing XLPE insulated, armoured, heavy duty LT underground electric cable with stranded aluminium conductor 1100 volts grade cross sectional area 10 sqmm 2 core laid in trenches, along poles through pipes etc complete all as specified & as directed. (i) Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately including taking down old unserviceable XLPE cable. (ii) Road cutting/floor cutting /cutting holes etc in walls required for laying/fixing of cable etc shall be made good as per existing. Nothing extra shall be admissible on this account. Quoted rates shall be inclusive of the above provisions.

Excavation in trenches n.exc 1.5M wide and n.exc 1.5M in depth for foundation and getting out in soft/loose soil all as specified and directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers n.exc. 25cm deep as in soft/loose soil copletete all as specified.

Removing excavated material n exc 50m and depositing where directed at a level n exc. 1.5 m above the starting point.

M&L brick work with fly ash bricks {As per IS-13757 (1993) burnt clay fly ash building bricks}, (Old size bricks) with width equal to the length of the brick laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection complete all as specified & directed.

M&L dry sand (tibba sand) and punning for cushioning to under ground cable all as directed. Note : For the purpose of payment only punned thickness shall be measured.

S&F sub main wiring on including passing throuh PVC conduit pipe 1100 volts grade with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 Sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 sqmm of green colour confirming to IS 694/1990 including taking down existing unserviceable sub main wiring. (Note : Two runs of cable with one run of earth wire and one run of PVC casing caping should measured as one length).

M&L 40mm grade GI pipe (light grade) for protection of LT cable fixed to wall /pole /road crossing including clamps complete all as directed.

Disconnecting from elect connection and taking down carefully the existing electric energy meter of any capacity, any make, any size and depositing the same in AGE E/M Store Yard all as specified and directed by the Engineer-in-Charge. Refixing the same inside the old meter inside box carefully including necessary electric connections complete all as directed.

Disconnecting from elect connection and taking down carefully the existing ceiling fan/exhaust fan/geyser of any capacity any make, any size and depositing the same in AGE E/M Store Yard all as specified and directed by the Engineer-in-Charge. Refixing the same ceiling fan/exhaust fan/geyser carefully including necessary electric connections complete all as directed.

M&L earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of plate not less than 1.5 m deep below normal ground level and connected to and including galvanized iron earth wire 4 mm dia by means of GI nuts, bolts, check nuts, washers thimbles, etc as shown in electrical plate No 3 of SSR Part-I and connection to main switch board/Test point/panel/ equipment and testing on including excavation and earth work in any type of soil, returning filling in, and removal of surplus spoil to a distance not exc 50 metre, charcoal and salt in alternate layer 15 cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe medium grade 20 mm bore for watering and 15 mm bore 3.00 metre long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25 mmx3mm, bolts, nuts and washers, PCC chamber (1:3:6) type C1, 40mm thick precast RCC cover 1:2:4 type B1 shall be provided on CI frame etc complete all as specified & as directed.

M/S JINDAL ENTERPRISES

shiva construction

Hitesh Construction

M/s KUNTAL ASSOCIATES

M/s Laxmi Enterprises

GAR CONSTRUCTIONS

KARTIK ENTERPRISES