Loading…
Loading…
| # | Company | Quoted % | Amount | Rank | Status |
|---|---|---|---|---|---|
| 1 | L1₹16.6 LAdmitted-Finance | -23.60% | ₹16.6 L | L1 | Admitted-Finance |
| 2 | L2₹18.5 LAdmitted-Finance | -15.00% | ₹18.5 L | L2 | Admitted-Finance |
| 3 | L3₹19.8 LAdmitted-Finance | -8.88% | ₹19.8 L | L3 | Admitted-Finance |
Tender Value
₹21.8 L
EMD Value
₹43,540
Closing Date
15 Jan 2026, 12:00 pmClosed
Ex Engineer JK SPORTS COUNCIL JAMMU
SPORT HOUSE M.A STADIUM JAMMU
Installation of water connection, electric connection and platform for boats at water sports centre basohli.2nd time
2026_SPORT_300276_1
enit no 66 of 2025-26 dated 09.01.2026
Open Tender
Civil Works
180 days
BILLAWAR
Please refer Tender documents.
3 documents required · 3 mandatory
₹600
Ex Engineer CDJ
₹43,540
SPORT HOUSE M.A STADIUM JAMMU
2 Feb 2026
9 Jan 2026
15 Jan 2026
9 Jan 2026
15 Jan 2026
9 Jan 2026
12 Jan 2026
Finishing walls with premium Acrylic smooth exterior paint with silicon additives of required shade: Old work (Two or more coats applied @ 1.43 liters/ 10 sqm) over existing cement paint surface.
Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6mm, with 40mm dia, steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer,
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete
Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in Cement mortar 1:4 ( 1 cement : 4 coarse sand)
Extra for half Brick masonry in superstructure above plinth level upto floor V level.
12mm Cement plaster of mix 1 : 6 ( 1 cement : 6 fine sand)
Finishing wall with premium acrylic smooth exterior paint with silicone additives of required shade on New work (two or more coats applied @ 1.43 liter/10sqm over and including priming coat of water exterior paint applied @ 2.20kg/10sqm)
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work
Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels (Area of slab upto 0.5 sqm)
Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. Single socketed pipes 75 mm diametre
Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. (external work) Medium 20 mm dia. nominal bore
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :610x460mm bowl depth 200mm
Providing and fixing unplasticised PVC connection pipe with brass unions: 45 cm length 15 mm nominal bore
Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931
Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg
Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding ,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete ,including fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Zsections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) Anodized aluminum (Anodized transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC 15)
Supplying and laying of PVC insulated and PVC sheathed/XLPE Aluminium power cable of 1.1 KV grade of following size on surface/direct in ground including excavation, sand cushioning, protecting covering and refilling the trench etc as required (armoured cable). 25 sq.mm 3.5 core
Installation, testing and commissioning of 200 mm sweep exhaust fan with robust motor, gravity shutters with speed rating of 1350 revolution per minute complete with all accessories etc. directly on ventilator , including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.
Wiring for circuit/ sub-main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in existing surface/ recessed PVC conduit as required.
Supply installation testing and commissioning of Ceiling Fan 3 Star Rated with Voltage Range 90 V to 300 V, 1200 mm dia, Min. Air Delivery 212 CMM, Service Value 5.3 Cu.m/min/watt, Aluminium Blades ,including wiring the down rods of standard length(Upto 45 cm)with 1.5 sq.mm FR PVC insulated,copper conductor,single core cable including providing and fixing phenolic laminated sheet cover on the Fan Box etc as Required.
Supplying and fixing of 400 mm sweep wall mounting fan (oscillating type) on wall with necessary connection as required.
Providing and fixing of 1 Hp pump with motor with necessary fitting & wire and connections complete as per direction of engineer incharge Havells or equivalent make
Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil
Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.All kinds of soil
Providing and laying of Gabion of mechanically woven, double twisted hexagonal wire mesh Gabion Type: Zinc coated mesh type 100 mm x 100mm, woven diagionally. Mesh wire dia 2.70, salvage wire dia 3.40 mm lacing wire dia 2.20 mm of GI wire including all leads lifts and carriages and cost of Stone and Gabion wire crates. The gabions shall have partions made of same material and each compartment shall be of size 1.2m x 1.00m
Carriage of material by M.T
Table with single drawer: Supplying & Placing executive table in completely knock down conditions with an overall size 1200mm X 600mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The table top shall be made up of 25mm thick particle board with approved laminate and finish as per approved shade. The profile shall be in rectangle shape with one side post forming edges. The top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 18mm thick particle board and profile shall be in linear shape. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It shall be 18mm thickparticle board with appropriate PVC edge banding connected with both end. There shall bebuffers provided at the base to avoid scratches on the floor. One hanging drawer shall beprovided with an overall size 400mm X 450mm X 150mm with key locking mechanism. Thedrawer shall be made up of Pre-laminated particle board of grade II of IS 12823. Drawerside, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The drawershall be operated with Al die cast handle and easily close & open with the assistance of ballbearing channel to enable smooth operation.
Revolving Chair: Supplying and placing ergonomically designed, comfortable & aesthetically appealing Low back chair. The seat shall be made of 15mm thick hot pressed plywoodupholstered withhigh resilience moulded polyurethane foam 40mm thick having density 45kg/m³ withmouse jute fabric tapestry 1mm thick and 300 GSM and the back shall be made of hot pressed plywood 12mm thick upholstered with high resilience moulded polyurethane foam 30mm thick having density 45kg/m³ with mouse jute fabric tapestry 1mm thick and 300 GSM with contoured lumbar support. The seat and back shall be individual with different plywood joint with HR steel sheet. The seat & back covered with polypropalene cover and the armrest shall be used PP arm completely joint with seat. The chair shall have push back360 degree revolving mechanism with upright position locking and tilt tension adjustment.The pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 120mm with BIFMA standard class-3 gaslift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal shall be made up of injection moulded black nylon having pitch circle Dia 650 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with BIFMAstandards. The Seat size shall be 445±10 mm(W)X430±10 mm(D) and back size shall be 465±10 mm(H) from seat & overall height = 800±10 mm.
Dinning Table MS Pipe Frame: Supplying & Placing cafeteria table with an overall size 1800mm X 900mm X 750mm. The top shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The top shall be supported on MS/CRCA rectangle pipe frame having cross-section area 70mm X 20mm with 1.6mm thick. The understructure shall consist of four legs made up of MS round pipe having dia. 38.1mm with 1.6mm thick. The Joints shall be made using TIG welding. The metal parts shall be powder coated to dry film thickness of 40-60μ. There shall be PPCP shoe provided at bottom to avoid scratches on the floor.
Dinning Chair MS Pipe Frame: Providing and supplying cafe chair. The seat and back shall be made up of injection moulded high impact strength polypropylene polymer. The understructure shall consist of MS/CRCA round pipe frame having dia. 22.2mm with 1.6mm thick and 35mm X 15mm capsule pipe with 1.6mm thick. It should be powder coated to the thickness of 40-60μ DFT. There shall be plastic show provided at the bottom. The overall size of the chair shall be 840mm(H) X 520mm(W) X 530mm(D).
3-SEATER SOFA: Supplying and placing a three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. The backrest of the sofa shall be supplied with traditional tufted buttons with decorative appealing. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall consist of SS 304 grade leg with shiny chrome finish having thickness 12mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 2000±10 mm(W) X 620±10 mm (D) X 430±10 mm (H). Overall width = 2600±10 mm, overall depth = 1000±10 mm & overall height = 740±10 mm.
2-SEATER SOFA: Supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 45Kg/m³ in seat and 32Kg/m³ in back. The backrest of the sofa shall be supplied with traditional tufted buttons with decorative appealing. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. The complete structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 571 GSM. The understructure shall consist of SS 304 grade leg with shiny chrome finish having thickness 12mm. There shall be buffers provided at the bottom to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 1330±10 mm(W) X 620±10 mm (D) X 430±10 mm (H). Overall width = 1930±10 mm, overall depth = 1000±10 mm & overall height = 740±10 mm.
CENTRE TABLE: Supplying & placing centre table with an overall size 1200mm X 600mm X 430mm. The top of the table shall be made up of 12mm thick toughened glass. The top profile shall be in rectangle shape and the edges shall be in chamfer shape. The under structure shall consistof MS Chrome plated pipe frame having cross-section area 30mm X 15mm X 1.5mm (T).There shall be shoe provided at the bottom to avoid scratches on the floor.
CORNER TABLE: Supplying & placing centre table with an overall size 600mm X 600mm X 450mm. The top of the table shall be made up of 12mm thick toughened glass. The top profile shall be in rectangle shape and the edges shall be in chamfer shape. The under structure shall consist of MS Chrome plated pipe frame having cross-section area 30mm X 15mm X 1.5mm (T).There shall be shoe provided at the bottom to avoid scratches on the floor.
Provision for supply and Installation of Pedestal for Inaguration made of MS Frame 40 x 40 x 2.6 mm with 4 mm thick ACP Sheet as base of size 4' x 6' and Acrylic Inaguration Plate Acrylic sheet cover as per direction of Engineer Incharge
Please Enable Macros to View BoQ information
stage.html
html • 0.03 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 1.89 MB
BOQ_974091.xls
BOQ • 0.32 MB
Download all tender documents and submit your bid