Construction of 50 beded Sheltter for Urban Homeless SUH at ITI Bus Stand under Ward No 33

Labour for cleaning the work site before and after work etc.

Dismantling pucca brick work including stacking serviceable material countable stacks within 15m lead …....do….E/I.

Dismantling P.C.C work including stacking serviceable material countable stacks within 15m lead …....do….E/I.

Dismantling R.C.C work including stacking serviceable material countable stacks within 15m lead …....do….E/I.

Taking down old door and window shutters including stacking serviceable material countable stacks within 15m lead …....do….E/I.

Taking down choukhats in doors including stacking serviceable materials in countable stacks within 15 m lead and disposal of unserviceable materials with all lead, all complete as per direction of E/I.

Providing, installing and fixing glow signboard of 20'x6'x6" size made with 4.0mm th HPL sheet and and framing of 35mmX35mm m.s. box section and 24" to 30" ht. aluminium channel box letter (all numbers and size, decided by engineer incharge/ Architect) with LED light including required electrical fittings and power supply system with all complete job and 5 years warranty..

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading,transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Earthwork in excavation in foundation trenches in ordinary soil (vide classfication of soil item - A) and disposal of excavated earth a obtained to a distance up to 50M including all lifts with leveling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design and per building specification and direction of E/I.

Extra for earth work in hard soil as per specification and direction of E/I (vide classification of soil Item B)

Providing coarse clean local sand in filling in foundation trenches or in plinth including ramming and watering in layer not exceeding 150mm thick with all leads and 1.5M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer Incharge (Mode of measurement compacted volume)

Filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume).

Filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume).

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cemen 2 Coarse sand) to match the existing floor:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4:8 (1 Cement: 4 coarse sand (zone-III): 8 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:3:6 (1 Cement: 3 coarse sand (zone-III): 6 graded stone aggregate 20mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:2:4 (1 cement: 2 coarse sand (zone-III): 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement: 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement:

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1cement: 1.5 coarse sand(zone-III): 3 graded stone aggregate 20 mm nominal size).

Making plinth protection50mm thick of cement concrete 1:3:6(1cement 3course sand6stone aggregate)….do…E/I.

Providing and laying damp proof course 50 mm thick with cement concrete M-150 with nominal mix of (1:2:4) ….do…..

centering and shuttering including strutting, propping etc. and removal of form for: Foundation.footing,bases of centering and shuttering including strutting, propping etc. and removal of form for:coloumn etc. for mass concrete.

centering and shuttering including strutting, propping etc. and removal of form for:Suspended floors,roofs,landings,balconies and acess platform

centering and shuttering including strutting, propping etc. and removal of form for:Shelves (Cast in situ)

centering and shuttering including strutting, propping etc. and removal of form for:Lintels,beams,plinth beams girders,bressumers and cantilevers

centering and shuttering including strutting, propping etc. and removal of form for:Columns,pillars,piers,abutments,post and struts

centering and shuttering including strutting, propping etc. and removal of form for:Stairs,(excluding landings) except spiral -stair cases.

centering and shuttering including strutting, propping etc. and removal of form for:Weather shades,Chajja,Corbels ec.,includingedges

Add for plaster drip course / groove in plastered surface or moulding to R.C.C projections.

Providing and mixing liquid integral water proofing compound in concrete of plaster as manufactureer specification and as per direction in charge .brand Sika plastrocrate plus,MYK proff WP 10 Fosroc -Conplastx4211C. Dr, Fixit,Pidiproff LW+or Equivalent.

Providing Tor steel reinforcement of 8mm dia rods as per approved -do- TMT Fe 500 (Only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd. Bokaro and Vizag (RINL)

10 mm dia

12 mm dia

16 mm dia

20/25 mm dia

Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I.

Extra for providing and placing in position 2Nos 6mm dia M.S.bars at every third coarse of half brick masonory

Extra for brick work for each consecutive floor above first floor including watering and scaffolding, all complete as per direction of E/I.

Providing 12mm cement plaster (1:6) with clean coarse sand of FM 1.5 with floating coat of neat cement in skirting Including rounding of Junctions with floor, curing, taxes and royalty all complete as per building specifications and direction of Engineer In Charge

Extra of plaster work over exterior surface for each consecutive floor above above first floor including cost of scaffolding etc. All complete as per direction of E/I.

Providing 6 mm thick cement plaster (1:4) in celling with clean coarse sand of F.M 1.5 Including screening, curing with all teads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/L

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface Including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding wahing of floors and taxes all complete as per building specifica tionand direction of E/I.

providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacture)with water absorption less than 0.08% and confirming to IS 15622/ISO 13006 of approved make,in all colour and shades,laid on 20mm thick cement mortat 1:4(1 cement:4 coarse sand),jointing with grey cement sulury @3.3kg/sqmincluding grouting the joints with wite cement and matching pigments etc.,complete size of tiles 600x600 mm.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS :15622 (thickness to be specified by manufacturer),of approved make,in all colours ,shades except burgundy,bottle green,black of any size as approved by engineer in charge ,in skirting ,riser of steps and dados ,over 12 mm thick bed of cement mortar 1:3(1cement:3 coarse sand)and jointing with grey cement sulury @3.3kg per sqm,including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Kota stone slab flooring over 20 mm thick base laid and jointed with grey cement slury mixed with pigment to match the shade of the slab inclding rubbing and polishing complete with base of cement mortar 1:4(1cement:4 coarse sand):25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting etc.laid on 12 mm (average) thick cement mortar 1:3.(1Cement:3 coarse sand) and jointed with grey cement slury mixed with pigment to match the shade of the slab inclding rubbing and polishing complete

Extra for pre finished nosing in treads of steps of kota stone/sand stone slab.

Providing and fixing at or near ground level factory made RCC pavement slab of M-30 grade of size 450x450x50 mm, including reinforcement with 6 mm dia M.S. bars 4 nos on each side, including setting in position in footpath to the required level and line over a bed of 20 mm average thick cement mortar 1:5 (1 cement : 5 coarse sand), having joint thickness not more than 5mm except on curve including filling of joints with same cement mortar and making grooves etc. complete as per direction of Engineer-in-charge

Providing and fixing pressed steel door frames conforming to IS:4351,manufactured from commercial mild steel of 1.60mm thickness including hinges,jamb,lock jamb,bead and if requires angle threshold of mild steel angle of section50x25 mm, or base f\tiles of 1.60mm pressed mild steel welded or rigidly fixed together by mechanical means,including M.S pressed butt hinges 2.5 mm thick with mortar guards,lock strikeplate and shock absorptio as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer -In- Charge.Prfile C fixing with adjustable lugs with spilit end to each jamb.

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one side teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinfoorced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Enginner-in-Charge.

30mm thick factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm . 19mm for styles and 15x15mm for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on eigher side forming styles: and 5 mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mmshall be tapered in 45 degree on the inner side to form top and bottom raiil and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail.

Supplying, fitting and fixing M.S. grill made of 20x6cmm M.S flat as per approved design and drawing, properly fabricated with Joints continuous fillet welded and finished smooth, carrlage of grill to work site, hoisting as per building specification and direction of E.I (where material is not supplied by the deptt.)

Steel work welded in built up sections/ framed work, including cutting hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.20 mm M.S. laths with 1.20 mm thick top cover

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be free, straight, mitred and jointed mechanically wherever required smooth, rust including cleat angle, Aluminium snap beading for glazing / paneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion or dyed to required shade according to IS: Anodised aluminium (anodised transparent 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the costof EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) or dyed to required shade according to IS: Anodised aluminium (anodised transparent1868, Minimum anodic coating of grade AC 15)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness

Providing and fixing aluminium tubular handle bar 3:2 mm outer dia,3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge Polyester powder coated minimum thickness 50 micron aluminium tubular handle bar

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete : Twin rubber stopper

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or deyed to required colour or shade with nuts and screws etc. complete 250X16mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm

Providing French spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed French polish including preparing the surface after cleaning removing dirt,scales grease including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Water proofing for Old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible

Covering of treated surface with PCC :- Providing 25 mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm

Providing and filling of 6 mm thickGroove between 25 mm PCC Panels with Polysulphide Sealant (Poring Grade)as per drawings and technical specifications and direction of E in Charge.(with 18% GST)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement will be allowed to air cure for 4 hours followed with water curing compound @ 0.126 kg/sqm. This layer for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110mm diameter (for rain water)

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler-110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend-110 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Shoe-110 mm

Providing and fixing on wall face unplasticised - PVC pipe clips of approved design to unplasticised -PVC rain water pipes by means of 50x50x50 mm hard wood plgs,screws of required length including cuttting brick work and fixing in cement mortar1:4 (1 cement :4 coarse sand) and making good the wall etc. complete

Providing 150 mm wide brick drain in cement mortar (1:6) with av. 150 mm clear depth and 125 mm apron Including cost of earth work Involved with 75 A, flat soling in proper grade and slope at the base, the drain duly plastered In C.M (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing

Sand (Lead Upto 42 km)

Local Sand (Lead 18 KM)

Stone Chips (Lead 15KM)

Bricks 08 KM

Flyash Bricks 08 KM

Stone Metal

Providing 12 mm thick water proofing cement plaster (1:3) with clean coarse sand of F.M 1.5 with floating coat of neat cement curing with all leads and lifts of water ,scaffolding taxes and royalty all complete as per building specification and direction of E/I

Supplying, assembling, lowering and fixing in vertical DSR position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to 15: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge 100mm dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. In Recharge Well (rh)

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. In Recharge Well

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750 mm deep, 600 x 450 internal dimension having 250 mm wall thickness in cement mortar ( 1:6 ) including 12 mm cement plaster ( 1:4 ) with punning on inside and cement plaster (1:6 ) with 600 x 475 mm G.I. cover with frame (Weight not less than 36 Kg.) in foundation and refilling all complete as per specification and direction of E/l.

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia Pipe

Supplying and fixing Cl. cover without frame for DSR manholes: 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg 15

Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dr brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. 'p' trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware footrest to be fixed in floor 15mm C.I. body brass spindle stop cock of weight not less than 50grms, 15mm P.V.C. connection pipe 450mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and dirction of E/I. 580mm long - With 12.5 Liter Low Level P.V.C. costern 580mm long - With 12.5 Liter Low Level P.V.C. costern

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthen ware urinal of Hindustan 'Parry' or any other approved I.S.S. make with 5 litres capacity C.i. automatic flusing cistern of reliance for any other I.S.S. approved make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grams, 15mm PVC/Alkthene pipe 450mm longwith brass coupling at both ends and doing plumber joints including priming coat of red oxide, cutting wall and floor making good the same etc. all complete as per specification and direction of E/I. Flat back or standard corner (600mm x 350mm)

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shad

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms:15 mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore approved brand C.P.Fittings.

Poviding and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 15 mm nominal bore, weighing not less than 32 gms

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Semi rigid pipe 32 mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the wall etc. 15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipe

40 mm nominal outer dia Pipe

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long,200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gm

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I. C.P. brass towel rail 20mmx600 mm with brackets container etc.

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required . 510x1040 mm bowl depth 178 mm

Providing and fixing Sink Cock with Swinging casted spout.

Providing and fixing PTMT swivelling shower, 15 mm nominal bore,weighing not less than 40 gms

Providing and laying on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. meter (for rain water)

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler-75 mm

Single pushfit Coupler-75 mm

Single pushfit Coupler-110 mm

Single tee with door-75x75x75 mm

Single tee with door-110x110x110 mm

Single tee without door -75x75x75 mm

Single tee without door -110x110x110 mm

Bend 87.5° -110mm bend

Shoe (Plain)-75mm shoe

Point Wiring in PVC Conduit, with Modular type Switch, Wiring for light point / fan point / exhaust fan point / call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc. as required.

Wiring for twin control light point with 1.5sqmm FRLS PVC insulted copper conducter single core cable in surface /recessed medium class PVC conduit ,2 way modular switch,modular plate ,suitable GI box and earthing the point with 1.5sqmm FRLS PVC insulated copper conducter single core cable

Supply and Fixing Light Plug Point with Modular Type Accessories : Supply and Fixing GI Box with modular plate and cover in front of surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc. as required.

Supply and Fixing Light Plug Point with Modular Type Accessories : Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connecting, painting etc. as required.

Power Plug Wiring in PVC conduit (2x4 sq mm): Wiring for light/power plug with 2x4 sq.mm FR PVC Insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 number 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required. Make-Havells/ Polycab KEI/Finolex/KEC

Circuit / Sub-main wiring in PVC Conduit : Wiring for circuit / Sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface / recessed PVC conduit as required. 2 × 1.5 sqmm + 1 × 1.5 sqmm Earth Wire

2 × 2.5 sqmm + 1 × 2.5 sqmm Earth Wire

S/F TP MCB DB : Supplying and fixing of following way, three pole and neutral, sheet steel, MCB distribution board, 415 Volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (without MCB / RCCB / ISOLATOR) (ALL TP MCB DB shall be as per IS:8623 4-Ways (4 + 12 Ways) Double Door

4-Ways (4 + 18Ways) Double Door

S/F ‘C’ Series MCB : Supplying and fixing 240 Volts, ‘C’ Series, Miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 6/32A Single Pole

40A TPN ,MCB

63A TPN ,MCB

S/F Modular type Switch/Socket: Supplying and fixing following modular type switch/socket on the existing modular plate and switch box including connections but excluding modular plate etc as required. Make-Havells/ Legrand/ Polycab/ C&S/ 5/6 Amps, one way switch

5/6 Amps, 3 pin socket outlet

S/F Electronic Call belt Supplying and fixing electronic musical call bell suitable for Each D.C/AC, single phase 230 volt complete as required

Supply and fixing of following size/modules, Gl box along with modular base & cover plate for modular switches in recess etc as required, Make-Havells/ Legrand/ Polycab/ C&S/ Hager/ABB 2 module (78 mm x 78 mmx45 mm)

84or 5 module(78mm x140mm)

8 or 9 module(78mm x230mm)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Bell push

S/F Batten / Angle Holder : Supplying and fixing batten / angle holder including connections etc. as required.

Supplying and fixing Modular type blanking plate-Supplying and fixing modular blanking plate on existing modular plate switch box excluding modular plate etc. as

ITC fluorescent fitting with down rods:- installation testing and commissioning of Prewired, fluorescent fitting/compact fluorescent fitting of all types, complete with all accessories and tube etc, including supplying and fixing ball and socket arrangement 2 nos down rods of 20cm diax1.6mm thick steel conduit/ Gl pipe upto 30cm length, painting and wiring the down rod and connection with 1.5 Sa. mm. FR PVC insulated.

ITC Exhaust Fan upto 450 min sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

Copper Earth Plate Elecrode: Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. (but with charcoal or cock and salt) complete etc. as required. Lightning Conductors-2 nos + Panels=1 no).

S/L 8 SWG copper wire in ground:- Supplying and laying 8SWG copper wire at 0.50 metre metere below ground level for conductor earth electrode, including soldering etc. as required.

Providing and Fixing Lightning Conductor Finial P/F of lighting conductor finial, made Nos. of 25mm dia 300mm long Gl tube, having single prong at top, with 85mm dia 6mm thick Gl base plate including holes etc. complete as required.

Gl lightning conductor tape in Vertical run Providing and fixing of Gl tape 20mm X3mm thick on parapet or surface of wall for lighting conductor etc complete as required. Metre

Gl lightning conductor tape in Vertical run Providing and fixing of Gl tape 20mm X3mm thick on parapet or surface of wall for lighting conductor etc complete as required. Metre

MV Cable:- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per 15:7098 armoured, served, sheathed, 1100V grade with Termination and Laying of cable. Make:- Finolex/Polycab/Havells/Mescab/KEI 4CX10 sq. mm armoured AL Cable. For JSEB supply

Supply of BLDC Ceiling Fan: Supplying and fitting of BLDC 5 Star, 32W, 1400 mm Sweep AC ceiling fan, including connection with 1.5 sq mm copper wire, down rod of standared length (upto 30cm) withall accessories as required. Make Polar/Bajaj/Crompton/Havells/GEC.

Supply of Exhaust metal Fan 230mm(9): Supply and fitting of 230mm(9"), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required(Make- Polar/ Havells/Crompton)

LED tube with Batten 20W: Supplying and fixing of wall mounted LED 20W tube Each light suitable for 230V, single phase supply voltage, with all accessorieslike batten and electronic driver and accessories as required. (Make -Bajaj Havells/ Philips/Jaquar)

Floodlights 80W Environmental friendly, new generation, aesthetically designed, ultra Each modern LED floodlight luminaire with high diecast housing and IP66 protection.( make: Jaquar/ Wipro/Havells/Bajaj/ Philips)

LED Surface mounting 6/7W (dress): Supplying and foxing of LED 6/7W surface mounting round down light and accessories as required. (Make -Bajaj / Havells/Philips/Wipro/Crompton)

LED Recess/Surface mounting 20W (Portico): Supplying and fixing of LED 20W surface mounting round down light and accessories as required. (Make -Bajaj Havells/ Philips/ Wipro/Jaquar)

LED Bulb 9W/10W: Supplying and fixing of LED 9W/10W bulb and accessories as required. (Make-Jaquar/Bajaj /Havells/ Philips)

Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. (a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to 150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supplying,fitting and fixing panel board with MCB Voltmeter main with starter having starting capacity and running capacity with indicator etc all complete as per specification RATE FROM ROTARY PARK

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable

Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

Mattress

Bed Sheet

Blanket

Pillow with Cover

Mosquito Net

Dinning Table

Chair

Wooden Chouki

Metal Drawer/steel almirah

CCTV Camera (13 Camera with all assessories)

Good & Service Tax (GST)

Labour Cess

Please Enable Macros to View BoQ information