Tankage Works@Sangrur Depot

F&E TK BTTM & ANNULAR — AS PER DETAILED SCOPE OF JOB ATTACHED.

F&E TK SHELL & W G — AS PER DETAILED SCOPE OF JOB ATTACHED.

F&E TK ROOF FOR CRVT — AS PER DETAILED SCOPE OF JOB ATTACHED.

D,S,F&E STRUCTURE — SUPPLY AND FABRICATION TANK STRUCTURAL STEEL, STRUCTURAL WORKS: DESIGN, SUPPLY, FABRICATION, ERECTION, PAINTING OF STRUCTURAL SUCH AS SUPPORT ANGLE, RIM ANGLE, TRUSS PLATES, STRUCTURES FOR CONE ROOF/INTERNAL FLOATING ROOF, RAFTERS, CURB ANGLE, SPIRAL STAIRWAY, MS SQUARE RODS, PLATFORMS, RAFTERS, WIND GIRDER SUPPORTS, ANCHOR CHAIR, FASTENERS, BRACINGS AND SUPPORTS, STIFFENERS, GUSSETS, EARTHING BOSS, LADDER ARRANGEMENT BETWEEN TWO 200 NB GAUGE WELLS, SUPPORT BRACKET FOR LIGHTENING ARRESTOR ETC. THE WORK SHALL BE COMPLETED IN ALL RESPECT AS PER DRAWINGS AND TECHNICAL SPECIFICATION AND DIRECTION OF THE ENGINEER-IN- CHARGE. THE COST OF MS BOLTS (PERMANENT AND SERVICE), WASHERS, ELECTRODES, PUTTY, GASES, SHIMS, PACKS, COST OF STRAIGHTENING THE RAW MATERIALS, CUTTING OF FLATS FROM PLATES AND PROVIDING SPLICES, TOOLS, PLANTS, TESTING OF MATERIALS, ETC. AND ALL OTHER CONSUMABLES AS REQUIRED FOR THE WORK SHALL BE DEEMED TO BE INCLUDED IN THE QUOTED RATES. ALL HANDLING AND TRANSPORT CHARGES OF RAW MATERIALS AND FABRICATED STRUCTURES INCLUDING DOUBLE HANDLING, AS REQUIRED, FOR COMPLETION OF WORK IN ACCORDANCE WITH TIME SCHEDULE, ARE DEEMED BE INCLUDED IN THE QUOTED RATES. THE SCHEDULE OF RATES SHALL BE READ IN CONJUNCTION (NOT IN ISOLATION) WITH THE TENDER DOCUMENT SUCH AS SCOPE OF WORKS. TENDER DRAWINGS, TECHNICAL SPECIFICATION, APPROVED MAKES AS PER CONTRACT AGREEMENT. RATE INCLUDES SURFACE PREPARATION BY CU SLAG BLASTING, ZN-PH PRIMER PAINTING (DFT-75 MICRON), MIO (100 MICRON DFT) AND EPOXY FINISH PAINT (DFT 2 X 40 MICRON). PREPARATION OF DESIGN, PREPARATION OF DRAWING FOR ALL STRUCTURAL IS IN SCOPE OF VENDOR. VENDOR TO TAKE PRIOR APPROVAL OF THE DESIGN AND DRAWING FROM HPCL/MECON. THE JOB TO BE EXECUTED AS PER ATTACHED TECHNICAL SPECIFICATIONS, JOB PROCEDURES ETC. COMPLETE AND AS DIRECTED BY EIC. NOTE: A. ALL STRUCTURAL WORKS FOR ABOVE GROUND TANKS SHALL BE PAID UNDER THIS ITEM EXCEPT HANDRAIL AND GRATING. B. HAND RAILS WILL BE PIPE HAND RAILS AND WILL BE PAID THROUGH SEPARATE ITEM. C. GRATING SHALL BE GALVANIZED TYPE AND WILL BE PAID THROUGH SEPARATE ITEM.

D,S,F&E GI GRATING — GRATING: DESIGN, SUPPLY, FABRICATION, ERECTION, AND PAINTING OF HONEY COMB PATTERN GALVANIZED GRATINGS. PREPARATION OF FABRICATION DRAWINGS INCLUDING BILL OF MATERIALS AS PER APPROVED TANK GA DRAWINGS, GETTING APPROVAL FROM CONSULTANT INCLUDING SUPPLY OF RAW MATERIALS, FABRICATION OF MILD STEEL GRATING IN PANEL SIZE AS PER APPROVED DRAWINGS, FABRICATED OUT OF 25 X 6 MS FLAT (OUTER FRAME AND STRAIGHT FLATS) AND ONLY THE BEND FLAT THAT IS HONEYCOMB SHALL BE DONE FROM 25 X 3 MS FLAT. SCOPE INCLUDES SUPPLY INCLUDING LOADING, TRANSPORTATION TO SITE, UNLOADING, STORAGE AND HANDLING AT SITE ,ERECTION AT APPROPRIATE LOCATION, LEVEL INCLUDING ALL NECESSARY CUTOUT IN GRATING SHALL BE MADE IF REQUIRED, INCLUDING ALIGNMENT WELDING OF GRATING ON SUPPORTING BEAMS/STRUCTURES IN TRUE TO LINE, LEVEL AND DIMENSION, TOUCH UP PAINTING WHEREVER REQUIRED. THE WORK SHALL BE COMPLETED IN ALL RESPECT AS PER DRAWINGS AND TECHNICAL SPECIFICATION AND DIRECTION OF THE ENGINEER-IN-CHARGE. THIS ITEM ENVISAGE SUPPLY AND FIXING OF GALVANIZED GRATING. THE MINIMUM GALVANIZED THICKNESS SHALL BE 80 MICRON. THE JOB TO BE EXECUTED AS PER ATTACHED TECHNICAL SPECIFICATIONS, JOB PROCEDURES ETC. COMPLETE AND AS DIRECTED BY ENGINEER-IN-CHARGE.

Shell man hole 600mm diameter — SUPPLY, FABRICATION AND ERECTION OF SHELL MANHOLE 600 MM: SHELL MANHOLE 600 MM SUPPLY, FABRICATION, ERECTION AND WELDING OF MANHOLE OF 600 MM DIAMETER WITH REINFORCEMENT PAD PLATES AS PER API 650 WITH ALL FLANGE, NUT, BOLT, COVER PLATE, HANDLE, NECK RING, GASKET ETC. FABRICATION OF MANHOLE COVER PLATE FROM FREE ISSUE PLATES. DESIGN, SUPPLY, FABRICATION, WELDING, ERECTION, TESTING OF THE ABOVE MENTIONED SHELL AND ROOF APPURTENANCES. RATE SHALL INCLUDE SUPPLY, FABRICATION AND WELDING OF NECK RINGS, SEAMLESS PIPES, BOLTING SLIP-ON FLANGES WITH BOLT, NUT, GASKET, TROUGH ETC. AS PER DRAWING COMPLETE AS PER SPECIFICATION. SCOPE OF SUPPLY OF HPCL SHALL BE LIMITED TO PLATES FOR RF PADS ONLY. THE SCOPE OF VENDOR INCLUDES PREPARATION OF DRAWING, GETTING APPROVAL FROM HPCL/MECON, SUPPLY, CUTTING, FABRICATION, WELDING, TESTING OF APPURTENANCES INCLUDING PIPE, FLANGE, RF PAD, MATCHING/COMPANION BLIND FLANGES. NO SEPARATE PAYMENT FOR RF PADS SHALL BE DONE. NOZZLE OF SIZE UP TO 300 MM DIAMETER SHALL BE FABRICATED THROUGH SEAMLESS PIPE CONFIRMING TO ASTM A 106 GRADE B SCH XS. NOZZLE OF SIZE 350 MM DIAMETER AND ABOVE CAN BE FABRICATED BY PLATE OF MIN THICKNESS OF 14 MM. THE JOB SHALL ALSO INCLUDE DP TESTING OF THE ROOT AND RADIOGRAPHY OF THE SEAM JOINT IN CASE OF NOZZLE BEING FABRICATED FROM PLATES. ONLY PLATES FOR REINFORCEMENT PAD WILL BE SUPPLIED BY HPCL. NOZZLE NECK LENGTH SHALL BE AS PER DRAWINGS/ DATA SHEETS/SPECIFICATIONS. THE JOB TO BE EXECUTED AS PER ATTACHED TECHNICAL SPECIFICATIONS, JOB PROCEDURES ETC. COMPLETE AND AS DIRECTED BY ENGINEER IN CHARGE.

I/O/R NOZZLE DN 650 — DETAIL SPECIFICATION AS GIVEN IN TENDER DOCUMENT

I/O/R NOZZLE DN 600 — SUPPLY AND FABRICATION OF SHELL NOZZLE 600 MM: TANK SHELL INLET/OUTLET/RETURN NOZZLE SUPPLY, FABRICATION, ERECTION AND WELDING OF NOZZLE OF 600 MM DIAMETER WITH REINFORCEMENT PAD PLATE, SEAMLESS PIPE/PLATE FABRICATED PIPE, TROUGH, ASA CLASS 150 SLIP ON FLANGES WITH DRILLED HOLE AS PER ANSI-B-16.5, GASKET, NUT, BOLT, WASHER, TROUGH INCLUDING INSTALLATION OF OWNER SUPPLIED VALVE COMPLETE AS PER SPECIFICATION. REINFORCEMENT PAD SHALL BE TESTED WITH SOAP SOLUTION BY APPLYING PNEUMATIC PRESSURE OF 1.05 KG/SQ.CM BEFORE HYDRO TESTING. CONTRACTOR TO SUPPLY ALL MATERIAL REQUIRED FOR THE NOZZLE. DESIGN, SUPPLY, FABRICATION, WELDING, ERECTION, TESTING OF THE ABOVE MENTIONED SHELL AND ROOF APPURTENANCES. RATE SHALL INCLUDE SUPPLY, FABRICATION AND WELDING OF NECK RINGS, SEAMLESS PIPE, BOLTING SLIP-ON FLANGES WITH BOLT, NUT, GASKET, TROUGH ETC. AS PER DRAWING COMPLETE AS PER SPECIFICATION. SCOPE OF SUPPLY OF HPCL SHALL BE LIMITED TO PLATES FOR RF PAD ONLY. THE SCOPE OF VENDOR INCLUDES PREPARATION OF DRAWING, GETTING APPROVAL FROM HPCL/MECON, SUPPLY, CUTTING, FABRICATION, WELDING, TESTING OF APPURTENANCES INCLUDING PIPE, FLANGE, RF PAD, MATCHING/COMPANION BLIND FLANGES. NO SEPARATE PAYMENT FOR RF PAD SHALL BE DONE. NOZZLE OF SIZE UP TO 300 MM DIAMETER. SHALL BE FABRICATED THROUGH SEAMLESS PIPE CONFIRMING TO ASTM A 106 GRADE B SCH XS. NOZZLE OF SIZE 350 MM DIAMETER. AND ABOVE CAN BE FABRICATED BY PLATE OF MIN THICKNESS OF 14 MM. THE JOB SHALL ALSO INCLUDE DP TESTING OF THE ROOT AND RADIOGRAPHY OF THE SEAM JOINT IN CASE OF NOZZLE BEING FABRICATED FROM PLATES. ONLY PLATES FOR REINFORCEMENT PAD WILL BE SUPPLIED BY HPCL. NOZZLE NECK LENGTH SHALL BE AS PER DRAWING/ DATA SHEETS/SPECIFICATIONS. THE JOB TO BE EXECUTED AS PER ATTACHED TECHNICAL SPECIFICATIONS, JOB PROCEDURES ETC. COMPLETE AND AS DIRECTED BY ENGINEER IN CHARGE.

I/O/R NOZZLE DN 300 — SUPPLY AND FABRICATION OF SHELL NOZZLE 300 MM: TANK INLET/OUTLET/RETURN NOZZLE: SUPPLY, FABRICATION, ERECTION AND WELDING OF NOZZLE OF 300 MM DIAMETER WITH REINFORCEMENT PAD PLATE, SEAMLESS PIPE, ASA CLASS 150 SLIP ON FLANGES WITH DRILLED HOLE AS PER ANSI-B-16.5, GASKET, NUT, BOLT, WASHER, TROUGH, INCLUDING INSTALLATION OF OWNER SUPPLIED VALVE COMPLETE AS PER SPECIFICATION. REINFORCEMENT PAD SHALL BE TESTED WITH SOAP SOLUTION BY APPLYING PNEUMATIC PRESSURE OF 1.05 KG/SQ.CM BEFORE HYDRO TESTING. CONTRACTOR TO SUPPLY ALL MATERIAL REQUIRED FOR THE NOZZLE. DESIGN, SUPPLY, FABRICATION, WELDING, ERECTION, TESTING OF THE ABOVE MENTIONED SHELL AND ROOF APPURTENANCES. RATE SHALL INCLUDE SUPPLY, FABRICATION AND WELDING OF NECK RINGS, SEAMLESS PIPE, BOLTING SLIP-ON FLANGES WITH BOLT, NUT, GASKET, TROUGH ETC. AS PER DRAWING COMPLETE AS PER SPECIFICATION. SCOPE OF SUPPLY OF HPCL SHALL BE LIMITED TO PLATES FOR RF PAD ONLY. THE SCOPE OF VENDOR INCLUDES PREPARATION OF DRAWING, GETTING APPROVAL FROM HPCL/MECON, SUPPLY, CUTTING, FABRICATION, WELDING, TESTING OF APPURTENANCES INCLUDING PIPE, FLANGE, RF PAD, MATCHING/COMPANION BLIND FLANGES. NO SEPARATE PAYMENT FOR RF PAD SHALL BE DONE. NOZZLE OF SIZE UP TO 300 MM DIAMETER. SHALL BE FABRICATED THROUGH SEAMLESS PIPE CONFIRMING TO ASTM A 106 GRADE B SCH XS. NOZZLE OF SIZE 350 MM DIAMETER. AND ABOVE CAN BE FABRICATED BY PLATE OF MIN THICKNESS OF 14 MM. THE JOB SHALL ALSO INCLUDE DP TESTING OF THE ROOT AND RADIOGRAPHY OF THE SEAM JOINT IN CASE OF NOZZLE BEING FABRICATED FROM PLATES. ONLY PLATES FOR REINFORCEMENT PAD WILL BE SUPPLIED BY HPCL. NOZZLE NECK LENGTH SHALL BE AS PER DRAWING/ DATA SHEETS/SPECIFICATIONS. THE JOB TO BE EXECUTED AS PER ATTACHED TECHNICAL SPECIFICATIONS, JOB PROCEDURES ETC. COMPLETE AND AS DIRECTED BY ENGINEER IN CHARGE.

I/O/R NOZZLE DN 250 — SUPPLY AND FABRICATION OF SHELL NOZZLE 250 MM: TANK INLET/OUTLET/RETURN NOZZLE: SUPPLY, FABRICATION, ERECTION AND WELDING OF NOZZLE OF 250 MM DIAMETER WITH REINFORCEMENT PAD PLATE, SEAMLESS PIPE, ASA CLASS 150 SLIP ON FLANGES WITH DRILLED HOLE AS PER ANSI-B-16.5, GASKET, NUT, BOLT, WASHER, TROUGH INCLUDING INSTALLATION OF OWNER SUPPLIED VALVE COMPLETE AS PER SPECIFICATION. REINFORCEMENT PAD SHALL BE TESTED WITH SOAP SOLUTION BY APPLYING PNEUMATIC PRESSURE OF 1.05 KG/SQ.CM BEFORE HYDRO TESTING. CONTRACTOR TO SUPPLY ALL MATERIAL REQUIRED FOR THE NOZZLE. DESIGN, SUPPLY, FABRICATION, WELDING, ERECTION, TESTING OF THE ABOVE MENTIONED SHELL AND ROOF APPURTENANCES. RATE SHALL INCLUDE SUPPLY, FABRICATION AND WELDING OF NECK RINGS, SEAMLESS PIPE, BOLTING SLIP-ON FLANGES WITH BOLT, NUT, GASKET, TROUGH ETC. AS PER DRAWING COMPLETE AS PER SPECIFICATION. SCOPE OF SUPPLY OF HPCL SHALL BE LIMITED TO PLATES FOR RF PAD ONLY. THE SCOPE OF VENDOR INCLUDES PREPARATION OF DRAWING, GETTING APPROVAL FROM HPCL/MECON, SUPPLY, CUTTING, FABRICATION, WELDING, TESTING OF APPURTENANCES INCLUDING PIPE, FLANGE, RF PAD, MATCHING/COMPANION BLIND FLANGES. NO SEPARATE PAYMENT FOR RF PAD SHALL BE DONE. NOZZLE OF SIZE UP TO 300 MM DIAMETER. SHALL BE FABRICATED THROUGH SEAMLESS PIPE CONFIRMING TO ASTM A 106 GRADE B SCH XS. NOZZLE OF SIZE 350 MM DIAMETER. AND ABOVE CAN BE FABRICATED BY PLATE OF MIN THICKNESS OF 14 MM. THE JOB SHALL ALSO INCLUDE DP TESTING OF THE ROOT AND RADIOGRAPHY OF THE SEAM JOINT IN CASE OF NOZZLE BEING FABRICATED FROM PLATES. ONLY PLATES FOR REINFORCEMENT PAD WILL BE SUPPLIED BY HPCL. NOZZLE NECK LENGTH SHALL BE AS PER DRAWING/ DATA SHEETS/SPECIFICATIONS. THE JOB TO BE EXECUTED AS PER ATTACHED TECHNICAL SPECIFICATIONS, JOB PROCEDURES ETC. COMPLETE AND AS DIRECTED BY ENGINEER IN CHARGE.