ADDN ALTN TO BLDG NO. P-183 AT AFSR IMPROVEMENT TO GUARD REST ROOM AT CAMP AREA PROVN OF WALL AT MAIN ENTRANCE GATE AND PROVN OF METAL CHANNEL SHEET BETWEEN IGLOO HUT NO. 2 3 AT AF STN PALAM UNDER GE (AF) PALAM DELHI CANTT - 10

Taking down cement plaster or cement lime plaster on brick or stone walls etc including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area n. exc 1.5 Sqm each and removing from site and making good the disturbed portion in CM (1:3) or PCC (1:2:4) type B1 (using 20mm graded stone aggregates) complete all as specified and as directed. Note:- The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface without any extra cost.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exc 1.5 Sqm but n. exc. 4 sqm each and removing from site and making good the disturbed portion in CM (1:3) or PCC (1:2:4) type B1 (using 20mm graded stone aggregates) complete all as specified and as directed. Note:- The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface without any extra cost.

Taking down shutter of any description exc 1.0 sqm and not exc 2 sqm each complete all as specified and as directed.

Demolition of brick work built in cement mortar, including all quoins, arches, pillars etc of any description including removing debrish from site complete all as specified and as directed.

M&L for 10 mm thick rendering using polymer modified ready-mix cement based mortar (conforming to IS- 1661- 1972, IS-2250-1965, IS:2402-1963) applied in ratio (1:3) as per manufacturer's instruction on brick work or concrete surfaces as on ceilings including finishing surface even and fair without using extra cement complete all as specified and as directed. Make:- Ultratech / Dr. Fixit / Fosroc

M&L for 15 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar (1:6), surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick rendering using polymer modified ready-mix cement based mortar conforming to (IS- 1661- 1972, IS-2250-1965, IS:2402-1963) applied in ratio (1:4) as per manufacturer's instruction on brick work or concrete surfaces of walls /damaged irregular surface of chajjas, roof projections, ceiling, fascia etc including finishing surface even and fair without using extra cement complete all as specified and as directed. Make:- Ultratech / Dr. Fixit / Fosroc. Note:- The cost of necessary scaffolding up to (G+2 storey) shall be deemed to be included in unit cost.

M&L for 15mm (average) thick rendering dubbing coat over damaged irregular surface of chajjas, roof projections, ceiling, fascia etc in CM (1:4) over cement slurry coat @3 Kg /sqm, making the surface even followed by 5 mm thick rendering in CM (1:3), surface finished even and smooth including making of drip course as required complete all as specified and as directed. Note:- (i) Rate for form work if required shall be deemed to be included in the rate quoted by the contractor. (ii) Rate for roughening surface of RCC/PCC by picking, sweeping, cleaning and washing down with water etc. shall be deemed to be included in unit rates.

M&L for washed stone grit plaster (of any colour/ pattern) on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15 mm cement plaster (1:1/2:2) (1 cement: 1/2 coarse sand : 2 coloured stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings and incuding taking down existing cement plaster or cement lime plaster on brick or stone walls etc complete all as specified and as directed by Engr-in-Charge. Note:- Payment for providing grooves shall be measured and paid separately.

Forming groove of uniform size 5-10mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using PVC battens/ strips, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete complete all as specified and as directed.

M&L for brick work with sub class `B' bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Description all as per ser item No. 12 above but except brick complete all as specified and as directed.

M&L for brickwork with old size sub class 'B' bricks, straight or curved on plan exc 6m mean radius, in half brick thick wall built in CM (1:4) complete all as specified and as directed.

Demolition of reinforced concrete roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed.

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole etc not exc 10 sqm on plan and not exc 1.5 metre in depth including getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25 cm in soft/loose soil complete all as specified and as directed.

Removing excavated surplus soil/material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed

M&L for PCC (1:4:8) type D2 (using 40mm graded stone aggregates) as in foundations, filling and mass concrete etc, complete all as specified and as directed.

M&L for providing RCC (1:2:4) (nominal mix) type B1 (using 20mm graded stone aggregate) as in footing, slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc and the like complete all as specified and as directed.

Use and waste for rough finished surfaces of concrete form work to sides and soffits of floor or roof beams, beam haunchings, columns, girders, bressummers, lintels, and simillar work complete all as specified and as directed.

M&L for providing RCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span concrete etc complete all as specified and as directed.

Use and waste for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exc 200mm thick (horizontal or sloping) complete all as specified and as directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide complete all as specified and as directed.

M&L for TMT or deformed bar 10mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

S&F mild steel TMT bars 8 to 10 mm dia as in stirrups, spacers and binders complete all as specified and as directed.

Demolition of concrete in ground floor and pavings n.exc 15 cm thickness below or above ground level complete all as specified and as directed.

Demolition of stone slabs and tiles laid, beded and pointed in any mortar of any description or any thicknes as in floors, aprons etc complete all as specified and as directed.

M&L for dark coloured / printed /highlighter ceramic tiles (digital first quality) of size (300 x 600)mm x 7 to 8mm thick as on vertical surfaces such as skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 10mm thick ready-mix cement based mortar adhesive for fixing tiles complete all as specified and as directed.

M&L for joint free coloured glazed ceramic tiles in vertical surfaces of size (300 x 200)mm x 7mm thick/ (450 x 300)mm x 7mm thick, set and jointed in cement slurry and pointed in white or coloured cement to match laid over & including 10mm thick ready-mix cement based mortar adhesive for fixing tiles complete all as specified and as directed.

M&L for joint free non skid coloured ceramic tiles, 7 to 8mm thick (squre or rectangular) area of each tile n. exc. 0.11sqm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the tile, laid over & including 10mm thick ready-mix cement based mortar adhesive for fixing tiles complete all as specified and as directed.

M&L for vitrified printed digital tiles dark shade, joint free, first quality in different colours pattern as in floors of 8 to 10mm thick (square / rectangular) polished, area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm as in floor etc including 10mm thick ready-mix cement based mortar adhesive for fixing tiles, set and jointed in neat cement slurry and pointed with coloured cement to match the colour of tiles complete all as specified and as directed.

M&L for vitrified ceramic tiles dark /printed shade tiles 20 mm thick (square/rectanglar) polished, area of each tile exceeding 2.6 sqm but not exceeding 3.0 sqm as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 10mm thick ready-mix cement based mortar adhesive for fixing tiles complete all as specified and as directed.

S&F vitrified ceramic tiles dark /printed shade tiles 18 mm to 20 mm thick (square/rectanglar) polished area of each tile in staircase riser & traider (one pice) ,vertical surfaces/skirting etc ,set and jointed with grey cement slurry mixed with pigment to match the shade of slab, size of slab exceeding 0.11 sqm but n.exc. 0.36 sqm including provision of screed bed 15 mm thick in cement mortar 1: 4 and a coat of cement slurry @ 3 kg/sqm including rubbing and polishing etc complete all specified.

M&L for granite (of any type) tiles 18mm to 20mm thick as in floor, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 10mm thick ready-mix cement based mortar adhesive for fixing tiles, cutting and polishing complete all as specified and as directed.

M&L for 18mm to 20mm thick granite single piece (of any type) work (table rubbed and polished) as in steps, jambs, pillars, walls, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 10mm thick screed bed or bedding layer ready-mix cement based mortar adhesive for fixing tiles and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for 18mm to 20mm thick Italian marble single piece (of any type) work (table rubbed and polished) as in steps, jambs, pillars, walls, window cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 10mm thick screed bed or bedding layer of morar including 10mm thick ready-mix cement based mortar adhesive for fixing tiles complete all as specified and as directed.

M&L for Durastone heavy duty tiles of size (600 x 600)mm x 10mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with pigments to match the colour of the tiles, over and including 15mm thick cement mortar screed bed in CM (1:6) complete all as specified and as directed.

M&L for precast cement concrete designer tiles 22 to 25mm thick glossy finish, heavy duty of approved brand and manufacturer and required shape and size as approved by GE over and including 15mm thick screed bed in CM (1:6) including pointing with coloured cement to match the shade of tiles complete all as specified and as directed.

M&L for 60mm thick glossy finish ultra interlocking designer tiles medium duty of any colour, shape or pattern as in floor, paving laid over 25mm thick sand cushioning set and jointed complete all as specified and as directed.

M&L fgor grinding and bees wax polishing as in floors, skirting, dado etc, with admixture of pigment to match the shade including repair work of existing Kota stone as same specification complete all as specified and as directed by Engr-in-Charge. Note: (i) Rates also including in this item for necessary replacement of terrazzo topping tiles and Kota stone slab etc which are required for repair of existing floor and no extra payment for utizied matarial in repair work in floor. (ii) Mode of measurement:- Actual area grinding with bees wax polishing with repair (floor and adjoining walls) shall be measured and paid.

M&L for stainless steel railing 110cm high including details as given below (not less then 1.6mm wall thickness) :- (a) Vertical post (baluster) 50 mm outer dia 96 cm high jointed with 20 mm dia 7.5 cm high alongwith base plate 100 mm dia x 15 mm and 16 gauge height as per sample fixed for each steps (treads) (b) 65mm dia hand rails & newal post including 100mm dia ball at top of newal post. (c) 4 Nos 25m dia bracing along the stair case 16 gauge all as per sample.

(I) Carefully dismantling of existing wall panelling (PVC / laminated / MDF / gypsum/wooden etc as existing) including removal of fixtures, screws, nails, etc., without damage and stacking the usable material within site. (II) Shifting and safe storage of dismantled panels for reuse as directed by Engineer-in-Charge. (III) Refixing of existing wall panelling at the same or other required location after completion of electrical conduit/wiring work, including necessary fixing arrangements, screws, adhesive, and alignment finishing. (IV) Providing and fixing new wall panelling (if damaged or missing) of same material, thickness, and finish as existing, including fixing accessories complete. (V) Touch-up, finishing, and cleaning after completion of all refixing work to match existing finish. Note: (a) All work to be executed as per the direction of Engineer-in-Charge. (b) Rate includes all labour, material (as applicable), tools and consumables items. (c) Measurement shall be taken for the actual area refixed and replaced only .

S&F in repair 12mm thick HDHMR (High Density High-Mosture Resistance ) boards, grade 1 quality, interior grade, commercial type, fixed with screws on timber frame-work as in Kitchen drawers, Cupboard shutters etc, complete all as specified and as directed by Engineer-in-Charge.

S&F 0.90mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed.

Dismantling ceiling, wall board, any size or description, fixed in any position or in any thickness, including cover fillets with nails complete all as specified and as directed.

Providing & fixing false ceiling at all heights with semi perforated 12mm thick micro tegular edged GRG (Glass Fibre Reinforced Gypsum false ceiling tiles of size (595 x 595)mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRCO.50 to 0.75 as per IS 8225:1987, noncombustible as per BS 476 (PART 4) -1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size (15 x 32)mm of length 3000mm, cross-T of size (15 x 32)mm of length 1200 mm and secondary intermediate cross -T of size (15 x 32)mm of length 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size (85 x 25 x 2)mm, Galvanised iron perimeter wall angle of size (24 x 24 x 0.40)mm of length 3000mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws complete all as specified and as directed.

Supply and fixing 10mm thicknees of PVC insulation panel with EPS stuck to 1mm printed PVC sheet suitable placed in false celling grid of GI frame for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20mm & 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre / intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc. 1.2metre length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre, provision of hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long, complete all as specified and directed.

Complete repair work only in existing ceiling board /frame, any size or description, refixing in frame and ceiling tiles in any position or in any thickness, including cover fillets with nails complete all as specified and as directed by Engr-in-Charge. Note:- The cost of tiles, T-Grid, suspended galvanized mild steel items, level adjuster of any size etc as required at site shall be deemed to be included in unit rate.

M&L for PCC (1:2:4), type B-1 (using 20 mm graded stone aggregate) as in copings, bed plates, with and including necessary form work in kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed

M&L for precast cement concrete PCC (1:2:4) type B-1 (using 20mm graded stone aggregates) as in landing cover slab, drain cover, shelves troughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and as directed

M&L for preparing plastered or unplastered new surfaces on ceilings including brooming down or steel wire brushing, scraping down and applying two coats of white wash complete all as specified and as directed

M&L for preparing old surfaces on ceilings including brooming down or steel wire brushing, scraping down and applying two coats of distemper oil emulsion complete all as specified and as directed

M&L for preparing plastered or unplastered new surfaces on walls including brooming down or steel wire brushing, scraping down, minimum 2mm thick cement base wall care putty and one coat of alkalic resistant primer and applying two coats of plastic emulsion paint complete all as specified and as directed

M&L for complete removal of existing treatment from external surfaces of walls by mechanicaly and washing, rubbing down and stopping of surface holes and cracks using necessary filling compound of white cement and fine sand in the ratio of (1:3) to obtain smooth regular/even finish using sand paper and applying cement base wall care putty minimum 2 mm thick and one coat of alkalic resistant primer and applying two coats of plastic emulsion paint complete all as specified and as directed.

M&L for preparing plastered or unplastered new surfaces on walls including brooming down or steel wire brushing, scraping down, minimum 2 mm thick cement base wall care putty over a coat of alkalic resistant primer and applying two coats of distemper oil emulsion complete all as specified and as directed.

M&L for complete removal of existing treatment from external surfaces of walls & ceilings by mechanicaly and washing, rubbing down and stopping of surface holes and cracks using necessary filling compound of white cement and fine sand in the ratio of (1:3) to obtain smooth regular/even finish using sand paper and providing cement base wall putty (minimum 2mm thick) over a coat of alkalic resistant primer and two coats of oil bound distemper complete all as specified and as directed by Engineer-in-Charge.

M&L for preparing plastered or unplastered old surfaces on walls including brooming down or steel wire brushing, scraping down, 3mm average thickness cement base wall care putty and applying two coats of texture paint over one coat of alkalic resistant primer complete all as specified and as directed.

M&L for preparation of new plastered surface of walls, chajjas, soffits & beam including necessary scaffolding and applying two coats of acrylic smooth exterior paint of required shade 1.43 ltr/10sqm over a coat of exterior primer 2.20kg/sqm over a coat of 2mm average thickness cement base wall care putty complete all as specified and as directed.

M&L for complete removal of existing treatment from external surfaces of walls, chajjas, soffits & beam including necessary scaffolding by mechanicaly and washing, rubbing down and stopping of surface holes and cracks using necessary filling compound of white cement and fine sand in the ratio of (1:3) to obtain smooth regular / even finish using sand paper and applying two coats of acrylic smooth exterior paint of required shade 1.43ltr/10sqm over a coat of exterior primer 2.20 kg/sqm over 2mm thick cement base wall care putty complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of steel of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old painted surfaces of wood and wood based material of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of old painted steel surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Dismantling structural steel work including door, gate but excluding framed truss etc. complete all as specified and as directed.

S&F MS steel work in tubular trusses and tubular posts and bracing including special shaped washers etc., complete using butt welded tubes confirming to IS 1161- 1979 graded St 240 complete all as specified and as directed.

S&F plates (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and as directed.

S&F PPGI pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding and fixed with self taping screws complete all as specified and as directed.

S&F 1 mm thick plain black mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified and as directed.

S&F framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed.

S&F collapsible steel gates top hung consisting of channel pickets, pivoted flat bars, box and bottom runners brass hadles etc as specified erected in position and securing runners with hold fasts and brackets complete all as specified and as directed.

M&L for 12 mm thick toughened glass automatic sliding door of Customizable / tentative size 2.50 M x 2.40 M systems (minimum opening 1.20 M) premium grade, high strength, perfect finish with microprocessor based control panel in out voltage 250V AC/50Hz having teth type transmission built with both ways sensor system, opening & closing speed 100-430mm/s (adustabale), door leaf weight better than 250 Kg, Power AC 200-250 Volt, 50-60 Hz, response time not exc 2 second, operating range 0.5 to 2 RM (adustabale) operating temperature -5 CTO 55 C motor type -DC Brushless motor heavy duty, safety features as auto -reverse on obstruction detection and Including locking arrangement on leafs, solar control film 50 micron reflective type sticked to glass panes complete all as specified and as directed. Make:- Godrej /saint Gobain / Modi /Indo Asain /ATUL or equivalent as approved by GE. Note:- Minimum two years comperhensive warranty on system and components shall be given by the contractor.

M&L for 12mm thick toughened glass door including rounding the edges and all necessary fittings such as locking arrangement, suitable handle 2 Nos each leaf, floor machine, pivot etc of suitable size floor spring (make:- Ozone or equivalent) patch fittings (matt black powder coated of make ozone or equivalent), door handles size 1200mm x 40mm x 2mm, locking arrangement on leafs (Make Godrej) fixed at site complete all as specified and as directed.

S&F toughened glass of 12 mm thick as in partition including all necessary fittings such as framer, clamps /bracket/ channels beadings etc of suitable size and make fixed at site complete all as specified and as directed.

M&L for solar control film 50 micron reflective type sticked to glass panes as per manufacturers instructions complete all as specified and as directed.

S&F unit insignia embossed (unit symbol) on glass as per sample approved by user unit door at alley way with one way visibility, and fixtured complete and glass partition above shutter to roof level complete all as specified and directed

S&F powder coated aluminum anodised grill DG-102 (10mm x 5.2mm) of decorative grill or equivalent fixed with 'F' Section size not less than 20.60mm x 15.20mm x 1.5mm thick of approved make complete all as specified and as directed. Note:- Minimum thickness of anodizing shall be 15 microns.

S&F door closer hydraulically regulated designation No 3 universal type suitable for door shutter of 851 to 1000mm in width of aluminum body (die cast) weight between 61 to 80kg complete all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of apertupre 1.40mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other party made of mild steel heavy duty complete all as specified and as directed.

S&F 100 mm long brass Mortice lock, 4 levers vertical type complete all as specified and as directed.

S&F sheet glass 4mm thick ordinary quality fixing to wooden door/aluminium window shutters in any position with new beads/ steel section as required for securing complete all as specified and as directed.

Taking down carefully existing aluminium sliding/openable window shutters, taking down of existing broken glass of any thickness from aluminium window shutters including existing rubber gasket complete, supply and fixing 4mm thick plain sheet glass with and including provision of new rubber gasket and re-fixing the shutters in existing position, complete all as specified and as directed. Note:- Shutter shall be of any description and size upto 2 sqm each leaf.

Taking down carefully aluminium sliding window shutters from the frames or chowkhat and supply and fixing new locking arrangement in place of old one and re-fixing the same shuters in existing position etc, complete all as specified and as directed. Note:- Shutter of any description and size upto 1.5 sqm each leaf.

S&F 30mm thick factory made single extruded WPC (Wood Polymer Composite) solid molded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless screws, complete all as specified and as directed. Note:- (a) Stainless steel butt hinges and necessary stainless screws shall be measured and paid separately (b) The unit rate shall deemed to be included of stainless steel 3 Nos hinges 100mm, 2 Nos aluminium Handle 150 mm, 2 Nos aluminium tower bolt 150 mm etc each leaf.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other frames/ chowkhat of size (45x85)mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed stainless steel screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs / stainless steel dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note:- (a) MS hold fast/ lugs or SS dash fasteners shall be measured and paid seperately. (b) WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified & directed.

S&F 0.5mm thick vertical venetian blinds Polyester Roller Zebra Blind for windows dual layer Zebra Roller shades, vertical type complete with hanging arrangement and rollers and chain etc complete all as specified and as directed by Engineer- in -charge. Make : Vista or equivalent.

S&F 25 mm dia, 1mm thick stainless steel Drapery rod, fancy type brackets & end knob as required complete all as specified and as directed. Note:- Minimum 2 Nos brackets and 02 Nos End knob in each door/ window to be provided without any extra cost.

M&L for 32mm bore low density polyethylene pipes (LDPE) of pressure rating 6Kg/Sqcm, fixed to wall, ceiling or in floor etc complete all as specified and as directed. (concealed type).

M & L for special treatment for sunken portion of WCs/Bath & toilet etc executed in following stages:- Stage 1: Providing 15mm thick plaster in CM (1:3) mixed with water proofing chemical of Dr.Fixit or Shalicrete 'R' of STP Ltd in the proportion/quantity all as per manufacturer's instructions. State 2 : Primer-Mix Tarfelt LM of STP Ltd (diluted with water in ratio 1:1) @ 250 gms/sqm and apply the primer on the plastered surfaces. Stage 3 : Application of 1st coat of Tarfelt LM of STP Ltd (without dilution with water) @ 1Kg/Sqm by brush all as per manufactuer's instructions. Stage 4: Laying fiber glass cloth (weight not less than 50gram/ Sqm) over the 1st coat while the coated surface is still sticky. Stage 5: After 6 to 7 hours interval, apply second coat i.e. final coat of Tarfet LM of STP Ltd (without Dilution with water) @ 1kg/ Sqm by brush as per manufacturer's instructions. Stage 6: Providing 10mm thick protective plaster in CM (1:3) mixed with STP No. 1 @ 250ml/50 Kg cement all as per manufacturer's instructions. Stage 7: Carryout ponding test for 48 hours to ensure water tightness of repaired sunken portion. NOTES :(i) Mode of measurement:- Actual area treated (floor and adjoining walls) will be measured and paid.

M&L for PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in roof kerbs, benching etc including weathering, slightly, rounded or chamfered angle and throughting complete all as specified and as directed.

M&L for plain cement concrete tiles (30cm x 30cm) x 20mm thick machine pressed, set & pointed in neat cement slurry in floor with grey cement and no pigment and cut and polished on roof over and including 10 mm thick screed bed in CM (1:4) complete all as specified and directed.

M&L for preparation of plastered/concrete surfaces of roof and applying the under mentioned course of roof treatement complete all as specified and directed by Engineer-in-Charge.:- (a) Plastering 10mm thick in cement mortar (1:4) on concrete surfaces using WPC @3% by weight of cement, finished even and smooth (b) Surface shall be thoroughly wire brushed, cleaned, washed, dried up properly and apply evenly a bituminous primer coat conforming to IS @0.4 ltr /Sqm over concrete / plastered roof surface. (c) Laying of 3mm thick APP membrane sheet (min weight 3 Kg/Sqm) consisting of a core of 160 gms/Sqm polyster non woven fabric mat protected on both sides with a high quality polymeric asphaltic mix again protected with thermo fusible HMHDPE FILM on dried primed surface by torch application method. APP membrane will normally be laid in length at right angle to the direction of slope. The over lap shall be minimum 100mm on longitudinal direction and 150mm on the transverse direction including cuttings, grooves etc. (d) Membrane bonded completely to the substrate & the overlaps are then scaled/fused by flame.

S&F vitreous china wash hand basin coloured of oval tiffany shape minimum of size 550mm x 400mm, bottle trap chromium plated heavy duty 32 mm dia, PVC connection of 15mm dia & 450mm long with PTMT nuts, 15mm bore basin mixer long swan neck chromium plated high pressure with high pressure and 32mm dia brass waste fitting complete all as specified and as directed.

S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size (580 x 440)mm white with integral foot rests, including connection to drain or outgoing pipe and to flushing pipe, anti syphonage pipe joint and to socket or stopper, including flush pipe with all fittings etc complete all as specified and as directed.

S&F vitreous china coloured wash down water closet pan cristy one piece EWC, including ‘P’ or ‘S’ trap and connection to drain & to flushing pipe, coloured seat cover, coloured 10 litres capacity low level flushing cistern super water saver dual including cast iron brackets and brass CP flush pipe long band, and mild steel chromium plated or aluminized hinging devices and 15mm dia Jet spray straight with CP tube 1 mtr long etc complete set and provision of concrete bedding complete all as speicified and and as directed by Engr-in-charge.

S&F in repairs low level flushing cistern 10 ltrs capacity, and connections to pipes and fixing of chain and pull, or lever, if any PVC valveless, syphonic action type, low level, white with inlet, including cast iron brackets complete all as specified and as directed.

S&F Plantex Ceramic Premium Wall Mount Large Urinal Pot (White, Loki) white or coloured with grating and union for discharge through bottle trap chromium plated heavy duty 32 mm dia, PVC connection pipe of 15mm dia & 450mm long with steel nuts, 15 mm dia angular stop cock long lever brass chromium plated with high pressure and 32mm dia brass waste fitting and including chromium plated spreader etc complete all as specified and as directed.

S&F curved shaped urinal partition size 900 mm x 450 mm of frosted glass 12 mm thick wall mounted fixed with steel bracket min 3 Nos complete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and as directed by Engineer-in-Charge.

S&F brass CP towel rail 600 mm long, fixed with and including chromium plated screws on walls, complete all as specified and directed. Make:- Prayag Cat No BA-01 or equivalent as per list of makes.

Taking up or down 15mm bore steel tubing and connections in walls, ceilings, floors, etc including cleaning for refixing or removal to store complete all as specified and as directed.

M&L for GI tubing, 15mm bore `medium grade` with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.

Taking up or down 20mm bore steel tubing and connections in walls, ceilings, floors, etc including cleaning for refixing or removal to store complete all as specified and as directed.

M&L for GI tubing, 20mm bore `medium grade` with all fittings and fixed complete to walls and ceilings or laid in floors etc complete all as specified and as directed.

Taking down CI pipes of 100/110mm dia of any description including all fittings complete all as specified and as directed.

Taking down CI pipes of 75/ 80mm dia of any description including all fittings complete all as specified and as directed.

S&F 75mm bore cast iron waste and vent pipe in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and as directed.

S&F 75mm bore cast iron waste and vent pipe in any length with or without ears fixed to walls including suitable iron clamps after every one metre of interval with cement joints fixed to wall complete all as specified and as directed.

S&F 100mm bore cast iron waste and vent pipe in any length with or without ears with cement joints laid in trenches or in floors complete all as specified and as directed.

S&F 100mm bore cast iron waste and vent pipe in any length with or without ears fixed to walls with cement joints fixed to wall including suitable iron clamps after every one metre of interval complete all as specified and as directed.

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls with and including suitable iron clamps at one meter of interval complete all as specified and as directed.

S&F CI 100mm bends complete all as specified and as directed.

S&F CI 100mm bends with door complete all as specified and as directed.

S&F CI 100mm single branch piece with door complete all as specified and as directed.

S&F CI 75mm bends with door complete all as specified and as directed.

S&F cast iron cowls 100 mm size complete all as specified and as directed.

M&L in repairs for cast iron Nahani trap/floor trap with CP grating including jointing with cement joint to waste pipe of 75mm dia fixed in cement concrete type B-1(1:2:4) complete all as specified

S&F in repairs for cast Iron 'P' or 'S' trap 100mm bore complete all as specified and as directed.

M&L for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed.

M&L Anti termite Treatment of wood work such as chowkhat or shutters by points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with putting complete all as specified and as directed by Engineer-in-Charge.

Rooting out trees, flora & fauna and foliage as grown on RCC roof surfaces and brick/stone walls by cutting hole into slabs/walls for digging out roots and using chemical to burn deep rooted tree roots etc and making good disturbed portion of wall/roof with cement concrete (1:2:4) type B1 (using 20mm graded stone aggregates) complete all as specified and as directed.

S&F 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling water tanks and removing from site with and including 20 mm ball brass valves, high pressure, with polythene float and flynut complete all as specified and as directed.

S&F ball brass valves, 20 mm bore, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

Disconnecting existing water tank exc 500 litres but n. exc 1000 litres capacity in any position, setting aside for repairs, cleaning and removing all scales, dirts etc from tank and mouth of circulating pipes etc and re-fixing in position complete all as specified and as directed by Engineer-in-charge.

S&F Kitchen plate rack made of stainless steel 1mm thick with plugs, washers as overall size (90cm x 90 cm) including fixing to wall and all accessories complete all as specified and as directed by Engineer-in-Charge.

S&F 5mm thick glass mirror of size exceeding 0.60 sqm but n. exc 2.0 sqm with making edges/ border moulding complete all as specified and as directed.

S&F in repairs 15 mm bore bib tap long body chromium plated, fancy type, cast copper alloy with capstan head screwed down, screwed for iron pipe or for brass ferrule fancy type complete all as specified and as directed.

S&F in repair 15 mm dia stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle fancy type screwed both side for iron pipe oe for union and fixed complete all as specified and as directed.

S&F in repair chromium plated bib taps fancy type of 15mm bore, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F in repair pillar tap 15 mm dia, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure with or without lettered Hot or Cold with screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and as directed.

S&F 15mm dia angular stop cock cast copper alloy screwed down, high pressure, screwed both side for iron pipe or for union and fixed complete all as specified and as directed. Make:- Jaquar code FLR-CHR-5053N or equivalent of make MARC or KOHLER as approved by the GE.

S&F Hand Shower (Health faucet) with 1.00 metre long Easy flex tube in chrome finish & wall Hook, complete all as specified and as directed. Cat No ALD-CHR-565 of JAQUAR or equivalent of make MARC or KOHLER as approved by the GE.

Demolition and breaking up 150mm dia drain pipes (slat glazed ware, AC or reinforced concrete) set in cement mortar complete all as specified and as directed.

M&L 100 mm thick concrete bed to drain pipes in cement concrete (1:4:8) type D-2 (using 40mm graded stone aggregate) including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and as directed.

M&L for unplasticisted PVC drainage pipe 160mm dia type 'B' with wall thickness 4mm (min) of pressure rating 6KN/Sqm laid in trenches and jointed with cement solvent including testing complete all as specified and as directed. Make:- Jain Pipes / Ajay flowgaurd / Astra pipes

M&L for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in surface channel, drain and manholes complete all as specified and as directed.

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in benching, coping including necessary use and waste of form work complete all as specified and as directed.

M&L for 75 mm thick PCC (1:3:6) type C1, (using 20mm graded stone aggregate) as in plinth protections, surface finished even and smooth without using extra cement complete including use and waste of necessary form work complete all as specified and as directed.

S&F stainless steel letters of metal 50mm width and height minimum 20cm to 30cm fitted on walls complete all as specified and as directed.

S&F 2mm thick stainless steel necessery unit insignia (logo/symbol ) area exc 0.25 sqm and not exc 0.50sqm complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Demolition of cement concrete or lime concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing the debries outside of defence land from the site complete all as specified and as directed.

M&L for 75mm thick cement concrete (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base including preparation, cleaning of existing surface to receive sub base complete all as specified and as directed.

M&L for cement concrete (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in floor levelling course and in similar situations 25mm thick complete all as specified and as directed.

M&L for rendering 15mm thick in two layers, 5mm thick using WPC @3% by weight of cement over 10mm thick on cement concrete block masonry/concrete surfaces in cement mortar (1:4), surface finished even and smooth without using extra cement complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

M&L for two coats of oil bound distemper over a coat of primer on old surfaces of ceiling complete all as specified and as directed.

S&F solid PVC coloured door frame of size (50 x 47)mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening as per specification and drawing complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter 28 to 30mm thick (sysles), with 2, 4 or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet polyeurethane painted on front face and 2mm plain colour PVC sheet on back face with particle board core complete all as specified and as directed.

S&F 100mm butt hinges medium weight cold rolled mild steel complete all as specified and as directed.

S&F 200mm long aluminium anodised barrel tower bolt complete all as specified and as directed.

S&F 200mm size aluminium anodised door handles complete all as specified and as directed.

M&L for pressed steel frames of size 105X60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including PCC (1:3:6) type C-0 (using 12.5mm graded aggregate) as in filling in frame complete all as specified and as directed.

M&L for 35mm thick flush shutters with lipping all around of solid core construction with block board core and ply wood face panels commercial type on both side complete all as specified and as directed.

M&L for brass sliding door bolt with sand or die cast brass hasp, staple (bolt type) length 300mm fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and as directed.

S&F 200mm long extruded brass handles, fabricated type polished complete all as specified and as directed.

S&F 200mm long brass barrel tower bolts, with cast or sheet barrel and rolled and cast bolts fixed complete all as specified and as directed.

M&L for 150mm decorative floor door stopper of brass fixed to door complete all as specified and as directed.

M&L for 0.9mm thick decorative laminate type1 of surface finish, colour and pattern as approved by Engr-in-charge, fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed.

S&F in repair vitreous china Orrisa pan squatting pattern of size (580x440)mm with integral foot rests including P or S trap, with and including PVC low level flushing cistern 10 ltr capacity complete all as specified and as directed by Engr-in-Charge.

S&F wash hand basin, vitreous china, coloured flat back of size (550 x 400)mm including cutting for and pinning in ends of brackets or erecting stand with and including brass CP grating, brass waste coupling, PTMT waste pipe, 15mm dia bore CP swan neck pillar taps cast copper alloy chromium plated fancy type complete all as specified and as directed by Engr-in-Charge.

S&F urinal, half stall type, white including CP waste coupling, fixed to 15mm dia pipe complete all as specified and as directed.

S&F chromium plated push type, auto closing concealed urinal flush valve with wall flange complete all as specified and as directed.

S&F stainless steel grating doom 125mm dia complete all as specified and as directed.

S&F 15mm dia bore, two way bib tap, long body, fancy type, brass chromium plated, with crutch handle, screwed down for iron Pipe complete all as specified and as directed.

M&L for 100mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F gun metal globe or gate valve with iron wheel head screwed both ends size 20mm for iron pipe, fixed complete all as specified and as directed.

M&L for cutting chases, pinning in brick, stone, concrete block walls, making good to facings where required and pointing in cement mortar (1:3) to concealed water tubing and making good complete all as specified and as directed.

S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls with and including suitable iron clamps at one meter of interval complete all as specified and as directed.

S&F PVC (SWR) bends of any radius 110mm bore complete all as specified and as directed.

S&F PVC (SWR) bends of any radius 75mm bore complete all as specified and as directed.

S&F 110mm dia PVC (SWR) vent cowl complete complete all as specified and as directed.

S&F brass CP wall mixer 15mm bore including connection pipes for mixing hot or cold water screwed down for GI pipe and fixed complete all as specified and as directed.

S&F in repair 125mm chromium plated shower roses with arm with or without swivel joints, any size including fixing to GI pipe complete all as specified and as directed.

S&F anodised powder coated (thickness of powder coating not less than 50micron) aluminim window and ventilator shutters, fixed type without sash bar, aluminium section weight not less than 0.55kg/mtr including necessary joining cleats, glazing clips, rubber packing, screws etc. complete all as specified and as directed.

Demolition of stone slabs and tiles laid beded and pointed in any mortar of any description or thicknes in floors, aprons etc complete all as specified and as directed.

M&L for Dholpur Elevation tiles as in vertical surfaces, 10 to 15mm thick (square or rectangular) area of each tile exc 0.11 Sqm and n exc. 0.18 Sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick ready-mix cement based mortar adhesive for fixing tiles & stone approved brand etc and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Surface dressing n exc 15cm deep and getting out in soft and loose soil complete all as specified and as directed.

M&L for broken stone or boulder hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface for plinth protection/path etc complete all as specified and as directed.

M&L for mild steel black sheet 1.60mm thick as in water troughs, ducts and similar work cut to size, bend to shape as required, holes punched, including round headed screws, cut nails or revets and fixed to steel framing with plain 40mm lap joints with reveted or welded seams including or turning up as per Engr-in-Charge including taking down of old sheet complete all as specified and as directed.

M&L for mild steel framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary gusset plates, riveting etc. complete conforming to Fe-290.(Gde E-165) complete all as specified and as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. and removing materials for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. any type complete all as specified and as directed.

Taking down ceiling/exhaust fan of any sweep after through cleaning of blades with a brush then by damp cloth dipped in soapy water to remove the remaining sticky stains and drying the same including lubricating by pouring oil, tightening all screws, ceiling plate and light fixture and refixing to its original position including provision of flexible cable, connector and connection from connector to fan complete painting of ceiling fans with synthetic enamel paint by spraying complete, including filling cavities with filler, one coat after cleaning all dust etc. complete all as specified and as directed.

Hanging/ refixing only ceiling/exhaust fan to its original position including provision of flexible cable, connector and connection from connector to fan complete all as specified and as directed.

Taking down unservesiable sub main wiring with conduits/battens etc complete all as specified and as directed.

M&L for point wiring with single core PVC insulated unsheathed 1.5 Sqmm FRLSH multistranded copper conductor cable 1100 volts grade IS-694 marked drawn in and including rigid non metallic PVC conduit medium grade not less than 20mm dia ISI marked with all conduit fittings and fixing accessories suitable for mounting modular switches including modular metal flush box and modular face plate with frame for mounting switches, sockets, fan regulators, etc and earth wire single core PVC insulated but unsheathed multistranded copper conductor cable 1100 volts grade IS-694 marked 1.5 Sqmm FRLS cable as continuous earth wire connecting to common earth dolly in concealed wiring system includes cutting of chases and making good disturbed surfaces complete all as specified and as directed for the following :- (a) One light/fan point controlled by one switch one way

(b) One 3 pin 5 Amps socket out let point on the same board controlled by one switch complete all as specified and as directed.

(c) One socket outlet 5 Amp controlled by one switch on independent board complete all as specified and as directed.

All as per Srl item No 197.00 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 sqmm stranded copper conductor cable PVC insulated including earth wire 2.5 sqmm copper conductor cable connected to earth dolly complete all as specified and as directed.

M&L modular switch 1 way 6 Amps 1 module complete all as specified and as directed.

M&L modular switch 1 way 16 Amps 1 module complete all as specified and as directed.

M&L modular socket outlet 6A, 2/3 pin combined 2 module complete all as specified and as directed.

M&L modular socket outlet 6A/16A, 2/3 pin combined 2 module complete all as specified and as directed.

Supply and fixing ceiling rose, surface type, 65mm x 50mm, 2 to 3 terminal complete all as specified and as directed.

S&F lamp holder, PVC/polycarbonate type with with back plate suitable for batten fittings complete all as specified.

S&F lamp LED 9 watt fixed in pendent holder/bulk head fittings complete all as specified and directed.

M&L for stepped type electronic fan regulator 230 -250 Volts, 2 module suitable for ceiling fan of size 1200 /1400 mm sweep complete all as specified and as directed.

Supply and fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 250mm complete all as specified and as directed.

Supply and fixing enviroment friendly indoor decorative 20 watt LED for wall mounted 20 Watt LED batten, extruded aluminium heat shrink provided for heat dissipation and integrated electronic driver back plate suitable for batten fittings complete all as directed. Make:- Havells Cat LHEWEBP7IN1W020 or equivalant

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Supply and fixing enviroment friendly indoor decorative mirror LED light fitting 1x10 watt with opal diffuser including all accessories suitable for batten fittings complete all as specified and as directed.

M&L for sheet metal enclosure for DBs 8 way double door type with 200 amps rated busbar SPN including necessary connection complete all as specified and as directed.

Supply and fixing for replacement vertical type load line distribution board, double door, 6 way, AC, 3 Phase, 415 volts, TPN, bus bar 200 Amps rating and earth bus & din rail suitable for MCCB as incomer complete all as specified and as directed.

Supply and fixing MCCB 160 Amps 4 pole 36 kA 415 Volts 50 Hz with thermal adjustable magnetic settings, necessary conection including taking out old existing unserviceable MCCB from panels/VTPN etc complete all as specified and as directed.

Supply and fixing for MCB, SPN, 40-63 Amp, 10kA complete all as specified and as directed.

Supply and fixing for MCB, SP, 5-32 Amp 10 kA complete all as specified and as directed.

Material and labour for submain wiring with two single core 4.00 sq mm PVC insulated FRLSH multistranded copper conductor cable drawing into and including rigid non metallic PVC conduit, medium grade ISI marked with all conduit fittings & fixing accessories and one single core 4.00 sqmm multistranded copper conductor cable as continuous earth wire complete all as sepcified and as directed.

Description all as per srl item No. 218.00 here in above but for 6.00 sqmm main wire and 6.0 sqmm earth wire complete all as specified and as directed. Note for ser No 218 & 219:- Two main wire, one earth wire, PVC conduit and cutting chases shall be deemed to be included in unit rate of one run.

S&F in replacement of LED street light fittings 60 Watt 230 Volt AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, GI pipe light grade 32/40 mm dia bracket to make L type & MS flat clamp of size 30mm x 5mm thick including nuts, bolts and washer suitable for bldg light fitting with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete all as specified and as directed.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB SP 20-32 Amps 'C' series complete all as specified and as directed.

M&L for earthing complete with galvanised earth plate electrode (600 x 600)mm x 6mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 meter below normal ground level, the earth plate surrounded by a mixture of charcoal dust and salt to a packed thickness of 150 mm on all sides with and including necessary excavation, earth work, returning filling in and removal of surplus spoil up to 50 mtr including GI wire 4 mm dia bolted and riveted to earth plate at one end in and connected to continuous GI earth wire encased in and including 15 mm GI light grade pipe with all fittings from top edge of earth plate complete as specified and as shown in electrical plate no 3 including testing on completion.

Supply and laying XLPE LT 1100 Volt grade, armoured under ground cable of size 95 sqmm 4 core with stranded aluminium conductor in trenches /passing through pipes/ on poles etc with and including necessary excavation, earth work and protection of cable complele all as specified and as directed. Note:- Excavation, earthwork and protection of cable shall be measured and paid seperately.

M&L for dry sand cushioning to underground cables with 8cm thick before laying of cables and 15cm thick after laying and stretching of cable complete all as specified and as directed.

M&L for old size sub class ‘B’ bricks, laid in trenches as cable covers complete all as specified and as directed.

M&L for rigid non-metallic PVC conduit exclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc. complete all as specified and as directed.

M&L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, cutting exceeding 20 cm girth complete all as specified and as directed.

Supply and fixing in replacement TV socket outlet modular type ISI marked with valid CML No. complete with sunken boxes, cover plates etc complete all as specified and as directed. Make:- Legrand Model-675546 or equivalent of approved make.

Supply and fixing in replacement Telephone socket outlet modular type ISI marked with valid CML No. complete with sunken boxes, cover plates etc complete all as specified and as directed. Make:- Legrand Model- 572322 or equivalent of approved make.

Please Enable Macros to View BoQ information