PROVN OF TRG SHED WITH OVERHEAD COVER FOR PHYSICAL TRG OF AGNIVEER AT SIKH LI INFANTRY REGIMENTAL CENTRE

Amount

M & L for surface dressing n.exc. 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Excavating over areas, n exc 1.5 m deep ; for foundation and getting out in soft/loose soil complete all as specified and as directed.

Excavation over areas, exc 1.50m but not exc. 3 mt depth. For Footing in soft/loose soil etc complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing Excavated material n. Exc. 50m and depositing where directed at a level n. Exc. 1.5m above the starting point etc complete all as specified and as directed.

M&L PCC (1:4:8) type D-2 (using 40 mm graded stone aggt) as in foundations, filling and mass-concrete etc complete all as specified and as directed.

M & L RCC M-25 design mix (using 20 mm graded stone aggt) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete etc complete all as specified and as directed..

M & L RCC M-25 design mix (using 20 mm graded stone aggt) in chajjas and the like etc complete all as specified and as directed.

M & L RCC M-25 design mix (using 20 mm graded stone aggt) as in Columns, pillars, piers, posts and struts etc complete all as specified and as directed.

M & L RCC M-25 design mix (using 20 mm graded stone aggt) as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed.

S & F for roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections,ractangular/sqaure hallow section ) including distance pieces, cleats etc conforming to Fe 410-W (Gde E-250) quality B complete all as specified and as directed.

S & F for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc conforming to Fe 410-W (Gde E-250) quality B complete all as specified and as directed.

S & F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa (not less than AZ 150) as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in ridge/valley gutter roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed.

M & L for preparation of new or previous untreated steel and iron surfaces of any description over 10 cm in width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M & L for rendering 15 mm thick in cement Mortar (1:4) on brick or concrete surfaces fair finished even and smooth w/o using extra cement complete all as specified and as directed.

M & L for rendering 15 mm thick in cement Mortar (1:6) on brick or concrete surfaces fair finished even and smooth w/o using extra cement complete all as specified and as directed.

M & L for preparation of new plastered surfaces of walls and applying two coats of OBD over a coat of 1 mm thick wall care putty complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over one coat of alkali resistant priming paint complete all as specified and as directed.

M & L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering etc complete all as specified and as directed.

M&L for 75 mm thick cement concrete (1:3:6) type C-2 (using 40 mm graded stone agg) as in plinth protection and path laid in panels, not more than 3.0 mtr in length, laid to slope 1:30 incl forming joints 10mm wide and duly filled with mastic bitumen (01 part bitumen mixed with 03 parts of sand) surface, complete all as specified and as directed. (Note : The quoted rates are deemed to be inclusive of material against form work and joint fillings.)

M&L Hardcore of Broken stones / boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M & L for 75 mm thick Cement concrete type D-2, 1:4:8 (40mm graded aggregate) complete all as specified and as directed.

M & L for 40mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) for flooring finished even and smooth without using extra cement including laid in alterntive bays etccomplete all as specified and as directed.

M & L for Glass dividing strips, 3 mm thick, 38mm of width and inserted in position, conform to design etc complete all as specified and as directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified and as directed.

M & L for form work as in sides of columns etc complete all as specified and as directed.

M & L for form work as in roof beams etc complete all as specified and as directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc complete all as specified and as directed.

M & L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and as directed.

M & L Mild steel TMT bars but 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and as directed.

M & L for MS TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as specified and as directed.

M & L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) etc complete all as specified and as directed.

M&L for Eco 4000 Series Windows fabricated from roll formed sections made of Galvanized Steel Colour Coated/Powder Coated (Base Steel as per IS 513 “D” quality, Galvanized as per IS 277 with Zinc of 120 grams/Sq. Mtr.) with total coated thickness of 0.60 mm. Coated Sections shall be with Primer Coat of Epoxy Primer of 5-7microns thick, finish painted with Polyester Paint of 12-16 microns thick and back coated with Alkyd backer of 5-7 microns, or Powder Coated with pure Polyester Powder up to 50-60 microns thick. Section for frame shall be 48mm x 50mm, Section for Mullion shall be of 48mm x 50mm, Section for Glazed Shutter Frame shall be of 47mm x 20mm, and Section for Fixed Glass Bead shall be of 12mm x 12mm. Frame and Shutter Frame Sections shall be cut to length and metre joined with Polypropylene Corner Brackets. Mullion Section shall be joined with Frame/Mullion using Nylon Mullion Cap. Ethyl Propylene Diamine Monomer (EPDM) Gasket shall be used all around glass in shutter. Each Glazed Shutter shall be provided with S.S. Pivot Hinges-1set, Seccolor Handle & Seccolor Stay. Window Frame shall be fixed to brick/concrete masonry by using Nylon self expanding caps and driving MS electroplated 80mm long screws into the caps through frames. Glass shutter & Fixed Glass portions shall be provided with a glass of 5 MM Plain Float Glass. Windows shall be provided with Grill made of 10mm sq. MS Bars welded to at 150mm center-to-center, 6mm x 12mm MS flat. Total grill unit shall be powder coated and fixed to window frame with screws Mesh Shutter shall be provided with a Stainless Steel 32 gauge Fly mesh of 304 grades with 144 holes per square Inch complete all as specified and directed. Note: Quoted rate shall deemed to be included rates of Glass and wire mesh, nothing extra shall be admissible on this account.

S&F factory made pressed steel frames for doors/windows of size size 125x60 mm (1.25mm thick MS sheet) with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, duly filling of cement concrete 1:3:6 type C-0 (using 12.50 mm graded crushed stone aggregate) to back of chowkhats, painted with a shop coat of red oxide primer complete all as specified and directed.

S&F factory made 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F mild steel sliding door bolt 300mm long clip type, stove enamelled black with bright bolt not less than 16mm diacomplete all as specified and as directed.

S & F mild steel barrel tower bolt 200mm long, stove enameled black with bright bolts complete all as specified and as directed.

S & F mild steel pressed handle oval type stove enameled black of size 150mm complete all as specified and as directed.

S&F mild steel butt hinges cold rolled of size 100mm medium weight complete all as specified and as directed.

M&L for preparation of new plastered surfaces and applying two coats of synthetic enamel paint, complete all as specified and as directed.

M&L for preparation of new plastered surfaces and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand etc complete all as specified and as directed..

M & L PCC 1:2:4 type B-1 (using 20mm graded stone aggt) as in kerb stone etc complete all as specified and as directed.

M&L for point wiring with 1100 volt grade PVC insulated and unsheathed 1.5 Sq mm (FRLS) multistranded copper conductor cable with continuous earth wire of 1.5 Sq mm (FRLS) multistranded copper conductor cable PVC insulated and unsheathed, drawn in & including concealed PVC rigid conduit medium grade with fittings (ISI marked) not less than 20 mm dia & 1.6 mm thick sunken pressed steel galvanised terminal boxes with top cover ISI marked plastic laminated hylam sheet for housing/ fixing switches etc for One light/fan/exhaust controlled by one switch complete all as specified and directed for the following- Note- (i) The quoted rete is deemed to be included for the chases cutting. (ii) Cutting chases for concealed shall be made good using CM 1:4 and surface finished to match the existing surface & colour.

Ditto as above but for One 5 pin 5 Amp socket point on an independent board with 2.5 Sqmm (FRLS) copper conductor cable complete all as specified and as directed.

Ditto as above but for One 5 pin 5 Amp socket point on same board….ditto…as …above

Ditto as above but for one 15 Amp 5 Pin switch socket combination independent with 4.0 Sqmm FRLS unsheathed copper conductor single core multistranded complete all as specified and as directed.

S&F Switch Piano flush type 5 Amp single pole one way complete all as specified and as directed.

S&F Socket outlet 2 in 1, 3 pin, 6A complete all as specified and as directed.

S&F Switch socket combination 5 in 1, 15 Amp flush type complete all as specified and as directed.

Supply and fixing of fan regulator 120 watts flush type for ceiling fan electronic type stepped range (5 steps) hum free including necessary connections complete all as specified and as directed.

S&F ceiling rose PVC/Poly carbonate isolated body three terminal 65/35 mm, AC 230 volts complete all as specified and as directed.

M&L for sub main wiring with two single core 6 Sqmm FRLS copper conductor PVC insulated and unsheathed cable including PVC conduit medium grade (appropriate size) concealed in wall for sub main connection including 6 Sqmm FRLS insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly all as specified. (Note:- (i)Two runs of 6 sqmm FRLS and one run of 6 sqmm FRLS copper conductor shall be measured as one unit length. (ii) The quoted rete is deemed to be included for the chases cutting. (iii) Cutting chases for concealed shall be made good using CM 1:4 and surface finished to match the existing surface & colour.

Supply and fixing of VTPN DB suitable for Mounting MCCB as Incomer of rating 100 Amp Vertical distribution board 12 way with suitable rated bus bar having IP-43 protection and double metal door concealed in wall including connection with aluminium thimbles as required complete all as specified and as directed.

Supply and fixing of MCB distribution board SPN 240 Volt 8 way with 200 Amp rated bus bar having IP-43 protection and double metal door concealed in wall including connection with alum thimbles as required complete all as specified and as directed.

S&F of MCCB 100 Amps, AC, 415 Volt, 4 Pole, 16 KA with thermal magnetic trip unit (TMTU) adjustable thermal setting 0.7 - 1 x In, class II front face, Ics = 100% Icu as per IS/IEC 60947-2 complete electrical connection by appropriate size of alum lugs complete all as specified and directed

S&F of MCB SPN 63 Amp 240 volt 'C' curve complete all as specified and as directed.

S&F of MCB SP 10 to 32 Amp 240 Volt 'C' curve 10 KA complete all as specified and as directed.

Supply and fixing LED lights fitting 4 feet, 20W, 220V, AC batten type with driver, holder including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose having luminaire lumen >2000 lm complete all as specified and as directed.

S & F building security LED Light 30 Watt sensor based made up pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC having top opening separate driver compartment with IP-65 protection and impact resistance of IK 07 for building secuity purpose with bracket size made of GI pipe medicum grade 25 mm dia 1.2 mtr long bend to shape as required and fixing with two nos MS Clamp of size 25x6 mm for fixing of builiding security light fittings complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods (upto 600mm long), electronic regulator and accessories, 230 V, 1200 mm sweep min air delivery 210 CFM with service value 6.00 BEE five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Supply and Laying cable XLPE Insulated screened PVC bedded, galvanized steel strip armoured service cable pole to building electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 4 Core complete all as specified and as directed.

Sand cushioning to under ground cable in layers of 23cm thick ( 8cm before laying the cable and 15cm after laying the cable) in trenches including punning the sand up to 18cm thick and consolidated complete all as specified and as directed. Note: Punned thickness only will be considered for payments

Supply and lay burnt best quality locally available old size sub class 'B' bricks laid in trenches perpendicular to U/G cable for cable protection complete all as specified and as directed.

Excavation in trenches n. exc 1.5 m wide and n.exc 1.5 m in depth and getting out soft loose soil complete all as specified and as directed for laying of under ground cable, foundation of pole and stay etc. complete all as specified and as directed

S&F of metal plug & socket DB with metal plug and MCBs single pole enclosere with a two pin earth plug and socket suitable for 20 Amp complete with one single pole MCBcomplete all as specified and as directed.

M&L for earthing complete with galvanised steel earth plate electrode 600 x 600 x 6 mm thick, burried directly into the ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to GI earth wire 4 mm dia by means of bolts, nuts, check nuts, and washers of galvanised iron or steel all as shown in electrical plate No - 3 connected to earthing test point all as specified or indicated including excavation and connected earth work, PCC chamber and cover, watering pipe, funnel wire mesh but without earth lead protection pipe and test on completion (above GL only) complete all as specified and as directed. (Note :- On testing after completion if desired earth resistence is not obtained, the earthing will be redone at no extra cost.)

M/S shree traders (BID ID -3290934)

M/S S P CONSTRUCTION (BID ID -3290646)

M/S WASEEM KHAN CONTRACTOR (BID ID -3293954)