SPL REPAIR TO BLDG NO T-13 NCC OFFRS MESS AT MORABADI POCKET UNDER GE RANCHI TO INCL FALSE CEILING OF ROOMS, TILING AND ALUMINIUM PARTITION IN ROOM AND PROVN OF SECURITY WALL CALDDING WITH ANGLE IRON POST AND GALVANIZED IRON SHEET AT OLD APS LOC NEAR

Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges as in roof covering.

Dimantling Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings.

S&F prepainted galvalume aluminium zink coating GI based corrugated/ semi - corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering fixed with coach screw as per manufacturers instrution complete.

S&F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall and ridge,fixed with self tapping srews complete.

S&F 0.63 Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 as in roof covering fixed with coach screw as per manufacturers instrution complete.

Dismantling timber scantling 40 sqcm and over in section in any position in framed work complete.

S&F for Steel work in tubular trusses including embeded in concrete with special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete Fe 410-W(Gde E-250) quality-A.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates

M&L Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to fe.290.Gde-E-165

Demolition of brick wk masonry built in cement mortar incl all quoins arches pillars etc

M & L Brick wk with sub class ‘B’ bricks straight or curved on plan exc. 6m means radius in CM 1:6

M&L Brick work with sub class 'B' Brick straight or curved on plain to any radius in half brick thick wall built in cm 1:4

Demolition of cement concrete (reinforcement) any description and positin not other wise specifically.

M & L for RCC (1:2:4) type B-1using 20 mm graded stone aggregate as in slab supported on wall ,Chajjas,deck slab Shelves/tank staging etc.

Use & waste frame work to sides and soffits of floor or roof slab, chajjas not exc 200 mm thick (Horizontal or sloping) rough finished complete.

M & L Mild steel bars 10mm dia TMT Bars and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

Dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing ) removing serviciable tile to store & rubbish off the permisses.

M&L for 15mm thick screed bed or bedding layer of mortar in CM (1:6) for lying floor finishes and surface fair and even.

M&L Vitrified ceramic tiles 8-10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete.

Description all as per ser item No 19 above, but as in verticle surface or skirting complete.

M&L Non - skid Ceramic jointless tiles of any colour/shade 7 to 8 mm thick area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles complete.

M&L for 10mm thick screed bed or bedding layer of mortar in CM (1:4) for lying on vertical surface to receiving wall tiles and surface finished even & fair.

M&L, glazed ceramic coloured tiles of size 350 X 250 X 7mm/ 450 x 350 x 7 mm thick as in walls etc set and jointed in neat cement slurry and pointed in colour cement to match the tiles.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons

M&L 18-20mm thick Granite slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including circular cutting,chamfering of edges as required.

Dismantling of wall and ceiling board any thickness/description including cover fillet.

M&L for GI frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre incl 2mm dia G.I. ( upto 1200 mm length ) adjusting level to Purlins/ Rafter. .

M&L 4mm thick non asbestos fibre cement designer building board of size 600X600 fixed or laid/inserted to timber/GI/Aluminium framework fixed in ceiling flat or sloping.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area n’exc1.5 Sqm and removing from site.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc1.5 Sqm but n.exc 4.00 Sqm each and removing from site.

Cutting holes in brickwalls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required not exc. half brick

M&L Pressed steel frames 125 x 60 mm size of frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

M&L Pressed steel frames 105 x 60 mm size of frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

S&F powder coated anodised/aluminium frame of size 65mm x 38mm x 1.00 thick or appropriate section as directed including with frame standard section for sliding type windows /ventilatorss with one or more rebates including joining cleats, beading, handle with locking arrangement, rubber gasket for fixing etc complete with and including 5.5 mm thick tinted glass n.exc 1 Sqm each panes (window of frame 3 tract wt not less than 0.50kg/RM and shutter having wt not less 0.45kg/RM) all as specified and directed

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z ections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chief.

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (style), with particle board core and 2, 4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

M&L Providing, cement concrete type B0 1:2:4 (12.5 mm graded aggreate) in filling of pressed steel frame , coping, fixing of MS railing work, fixing of hold fast etc similar work.

S & F 100 mm Butt hinges medium weight medium cold rolled mild steel.

S & F 100 mm Butt hinges extrucded aluminium alloy with galvanised mild stel hinge pin, anodised and fixed, type C-21.

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section complete.

S&F of 150 mm size aluminium handles cast type anodised.

S&F 250mm long Aluminium alloy, anodised, sliding door bolts with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extructed section or cast aluminium alloy and fixed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples over steel windows and gauzed door.

S & F 4 mm thick figured glass pin headed type complete.

S & F 6 mm thick figured glass pin headed type complete.

Demolition of cement concrete (un-reinforced) in ground floors and paving n.exc 15cm thick (below or above ground level).

M&L for 75mm thick PCC type C2 1:3:6 (using 40mm graded stone agg) as in plinth protection/Path/floor finishing surface of concrete topping even and fair without using extra cement complete.

M&L for Sand filling under floors or in foundation including watering and consolidation for laying interlocking tiles complete all as specified and directed.

M& L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey cement and no pigment in paths and hardstanding laid tightly over & including 25 mm thick dry sand cushion (compacted) and joint filled with dry sand(colour and pattern as approved by GE) complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connection including cleaning for re-fixing or removal from site.

S & F, 15mm bore galvanized steel water tubing medium grade with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors.

Cutting chases, pinning in, in brick walls making good to facings where required and pointing in cement mortar 1:3 to concealed water tubing and making not exc 10 cm girth.

Taking up or down 20mm dia steel tubing and connection including cleaning for re-fixing or removal from site.

S & F, 20mm bore galvanized steel water tubing medium grade with all fittings such as bend, elbow, socket reducer etc fixed to walls and ceilings or laid in floors.

S&F in repair PVC (SWR) pipes 75mm single socketed in any length with rubberring joints, laid in trenches or in floors

S&F in repair PVC (SWR) pipes 110 mm single socketed in any length with rubberring joints, laid in trenches or in floors

S&F in repair PVC bends any radius 75 mm dia

S&F in repair PVC bends any radius 100 mm dia

S & F in repair vitreous china wash hand basin,counter top, white as approved and directed by Engr in charge.

S & F 32 mm Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed

S&F in repair vitreous china pedastal type water closet, white, all in one piece including connection to trap etc complete as approved and directed by Engr in charge.

S&F in repair EWC sheet cover to match EWC complete.

S&F in repairs Health fauset (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 meter long flexible tube and ABS wall hook incl making connections and fixed in position complete in all respect as specified.

S & F in repair vitreous china urinal, half stall flat back, white as approved and directed by Engr in charge.

S&F in repair, 450mm long, 15mm dia, PVC connection pipe, with brass unions on both ends.

S & F in repair, 15 mm bore bib taps, chromium plated cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule.

S&F in repair 15 mm bore angle/ stop valves , fancy type chromium plated with long shank and cup (conceaeld type), screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as spfd & directed by Engr-in-charge.

S & F 15 mm bore two way long body bib taps, chromium plated cast copper alloy, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

S&F 20mm dia Aluminium powder coated as in golden colour finish draft rod complete all as specified and as approved by EIC.

S&F brass chromium plated decorative bracket fixed to wall .

S&F in repair Brass chromium plated tubular towel rail 20mm dia D Type, 60 cm long between flanges.

M&L in repair 75mm dia PVC(SWR) floor trap, plain with grating including jointing with solvent cement complete.

Taking down cement plaster of any description on brick or stone walls/concrete surface etc. including racking out joints, hacking for key, scrubbing down with water etc.

M & L, 15mm thick rendering on fair faces of brick work/concrete surface in CM (1:6) surface finished fair & even complete.

M & L, 15mm thick rendering on fair faces of brick work/concrete surface in CM (1:4) surface finished fair & even complete.

M&L for preparation of new plasterd wall surfaces and applying two coat of oil bound distemper of approved colour and shade over one coat putty .

M&L for preparing old plastered surfaces of wall and applying two coats of distemper oil emulsion over one coat putty .

M&L for applying Two coats of acrylic emulsion paint exterior paint of required shade over and including priming coat of exterior primer over a coat of plaster of paris putty of 1mm thickness after complete removal of existing treatment on wall surfaces.

M&L, applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of newly steel surfaces of any description over 10cm width or girth not otherwise described.

S&F floor door stopper 150 mm of brass body and tongue anodised with hard drawn steel spring fixed .

S & F in repairs Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm

S&F in repair stainless steel plate rack 1mm thick of size 750X600mm and depth 250 mm , fixed on wall surface as per manufacturer's instruction and making good the surfaces .

S & F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long

S&F Chromium plated toilet paper holder with flap of standard size as approved by GE.

S&F Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern

S&F CP Towel ring, square type including CP screws complete.

S&F CP soap tray fixed with rawl plugs complete.

S&F in repair brass chromium plated wall mixer with hot and cold arrangement, long shank suitable for 15 mm bore of pipe of approved quality as approved by EIC.

S&F in repair brass chromium plated Basin mixer with hot and cold arrangement, long shank suitable for 15 mm bore of pipe of approved quality as approved by EIC.

S & F Grating doom 100mm dia of PTMT (Minimum weight 25gms)

S&F in repairs brass Chromium plated shower rose 125 mm size with or without swivel joints any size incl fixing of steel pipe or union .

Dismantling fencing wire mash any type

Dismantling posts/pillers or struts (Wood, Steel, or RCC) any section, including taking out embedded portion in natural ground and making good disturbed ground.

Excavating in trenches, n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc, or for shafts, wells, cesspits, manholes, pier holes, etc n exc 10 sqm on plan and n.exc 1.5m in depth and getting out soft/loose soil.

Returning filling in including spreading levelling, watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Removing excavated materials not exc 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point in soil.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone as in foundation , filling and mass concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40 mm graded stone as in foundation , filling and mass concrete as in post holes, surface channels and drain etc complete all as specified and directed.

M&L cement concrete 1:2:4 type B-1 as in copings including weathering slightly rounded or chamfered angles and throating incl formwork.

M&L rendering 15mm thick cement plaster on fair faces of brick work or concrete surfaces and finishing surface even and smoth compelte all as specified in 1:4 CM.

S&F Mild steel framed work as in posts and struts in fencing including cutting tops to shape as directed, drilled holes,notching for wire etcflats iron fillets (for securing wire mesh etc ) including all necessary drilling,bolting or fiveing etc, and similar work confirming to Fe-290 GdeE -165 all as specified and directed.

S&F Pre-painted galvalum alm zink coating GI based corrugated/ semi - corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering fixed with coach screw as per manufacturers instrution complete.

S&F 2 strand barbed wire galvanised, 2.24mm dia barbed 2.00mm dia barbed at 75mm spacing and straing and fixing to any type of standared rails staining bolts, including,securing or tying at crossings with and provision of galvanised mild steel wire, stables or steel pins,etc., as directed

Preparation of new steel surfaces and two coat of synthetic enamel paint over a coat of red oxide primer.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for taking credit and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface complete all as specified and directed.

Taking down ceiling fan/ exhaust fan and refixing of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades complete all as specified and as directed.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :- (Note: Rate of modular cover plates are deemed to be included in the rate quoted)

One light point controlled by one, one way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

One 3 pin 5 Amps switch socket outlet point controlled by one switch on the same board.

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

Description all as per item No 111 here in before but using 2.5 sq mm single core copper conductor cable FRLSH of multistranded PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point including necessary running of 2.5 sq mm FRLSH copper conductor cable PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly.

S & F for Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified

S & F for Modular Switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as specified.

S & F for Modular Switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as specified.

S & F for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed.

S & F for MCB Single pole and neutral rated capacity 40 to 63 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.

S & F for Decorative wall mounted luminaire made out of polycarbonate with unbreakable globe suitable for LED bulb and provision of LED bulb 9/10 watts complete all as specified and as directed. Make Havells , Philips, Bajaj.

S & F for Lamp holder, PVC body suitable for batten fitting completes all as specified.

S & F for LED mirror light 9/10 watts batten aluminium extruded with decorative end caps complete all as specified and as directed. Make- Bajaj Havells, Philips.

S & F for Energy saving new generation 9/10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. Make :-Havells Bajaj Philips

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make :- Make Bajaj Philips, Havells.

S & F for recess mounted 2' x 2' square LED panel 36 watts, design aluminium housing, polycarbibate diffuser white powder coated finish operating voltage 140 volts - 270 volts, AC, 50 Hz complete all as specified and as directed.

S & F Energy saving new generation environmental friendly long life versatile pressure die cast aluminium ip 66 for building security light fitting luminare with high power LEDs as light source and electronic driver of capacity 35 watts with pre wired and necessary mounting arrangement and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer-in-charge.Make:- Bajaj, Philips, Havells

S & F for metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed

Supply and replacing 1100 volts grade heavy duty PVC insulated aluminium conductor, served with inner sheathing of PVC in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm dia GI suspension wire, one twin core cable of size 10 Sqmm multi -strand complete all as specified and directed.Make : Havells/Polycab/KEI

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 4.0 Sqmm nominal area and drawing into PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size concealed in wall etc including one run of PVC insulated 4.0 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and as directed. Note:- Two runs of 4.0 sqmm cable,one run of 4.0 sqmm cable and one run of PVC casing caping will be measured as one unit

S & F for metal body exhaust fan, AC single phase, 240 V of size 225 mm sweep 1380 rpm with louvers including necessary connection and replacement of flexible copper cable from ceiling rose and M&L for making hole and proper finishing the surface as existing before and taking down of old unserviceable fan complete all as specified and as directed

M& L for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised earth wire 4mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate No 3 of MES Schdule Part-I connected to earthing point and testing on completion with and including 15mm bore light grade GI protection pipe (upto 7.5 meter beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C-1 with RCC 1:2:4 type B-1, 40 mm thick cover reinforced with 8mm dia TMT bars 3 Nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore medium grade GI watering pipe common salt and charcoal filling, necessary excavation and earth work complete