SPECIAL REPAIR FOR REPLACEMENT OF LIFT 20 PASSENGER AGAINST BER AND COMPREHENSIVE MAINTENANCE OF ELECTRIC LIFT OF 20 PASSENGER IN MH UNDER GE SATWARI

Amount

LIFT:- Supply, installation, testing & commissioning of hospital elevator / electric lift 20 passenger (1360 kgs) capacity with microprocessor controlled (gearless) suitable for hospital stretcher, Speed 0.4 metre/second to 0.6 metre/second with single speed, 415 volts, 3 phase AC 50 Hz supply, confirming to IS-14665 and as amended, suitable to serve G+1 (02 floors) with AC Variable Voltage & Variable frequency Drive (VVVF) complete with all standard accessories,full collective operation ( simplex automatic & manual dual controlled operation with/ without attendant), telescopic sliding (side opening) stainless steel doors with door driver (electric motor driven mechanism), automatic rescue device (ARD) system, 3D infra red sensor in full height of door & built in announcing system without hand set (03 Nos, one each in car, Machine Room & near Ground floor landing door) complete incl earthing to equipments and all other associated equipments/ accessories complete all as per particular specfication including comprehensive maintenence of lift during defect liability period. all as specified and directed.

MAKES OF LIFT ;- OTIS ELEVATORS/ KONE / SCHINDLER / THYSSEN KRUPP ELEVATOR / JHONSON / HITACHI.

Car & Car Door details: Adjustable door Openeing & closing time, Alarm Button, Car call cancellation at terminal Stop, Fire rated door, Direction arrow and position indicator on all stops, SS mirror finished Hand rails on rear side of car panel, Home landing in emergency, Phase failure and phase reversal protection, Emergency firemen's services, Emergency Car light unit, Infra red Curtain, Door Protection, Door time Protection, Emergency Alarm Button, Door open / close button, Mannual rescue Operation, Auto fan cut off, Intercome, Overload indecator, Car light : Sufficient wattage LED light should remain 'ON' during the operation, Ventilator : One fan for AC 230 V 50 C/S Non-Oscilllating type of adequate sweep fitted flush with ceiling, Car Door type: Auto 2 panel telescopic (ATO 2P), Car Enclosure: SS Hairline, Car Door Enclosure: SS hairline, Flooring: PVC Black Anti Skid, Entrance width front side : 1200 mm Entrance Height front side: 2000 mm.

The existing details of LIFT WELL i.e. Civil works of the shaft at site are as under :- (a) Machine room location : above hoistway, (b) Travel Height : 3700 (mm) (c) Pit depth : 1600 mm (d) Overhead height : 4500 mm (e) Maximum floor to floor distance: 4500 mm (f) Hoistway width : 2200 mm, (g) Hoistway depth : 3000 mm, (h) Machine room width : 3600 mm, (j) Machine room depth : 5000 mm, (k) Machine room height : 3500 mm.

NOTES :- (i). The lift shall be confirming to relevent IS specifications as applicable and the cost shall be deemed to include the provision of any other parts necessary for installation and running the lift. (ii). Machine Room floor slab must be cast after the slab marking for rope pockets holes by OEM (iii). Machine room walls, floors and ceiling to be treated and painted to minimise accumulation and circulation of dust. (iv) All civil works pertaining to Lift and Machine Room shall be executed, measured and paid in the respective items of this schedule / BoQ.

Supply, laying and testing XLPE, insulated screened, PVC bedded galvanized steel strip or wire armoured, electric power cables, heavy duty, with aluminium conductor, 1100 volts grade, 3.5 core, cross sectional area 35 Sqmm, all as specified and directed.

Switch disconnector fuses of capacity 63A, Three pole and neutral in sheet steel enclosure with HRC fuse of same make complete all as specified and directed. Make Indoasian cat No. IN1A063 or its equivalent in L&T/Legrand.

INTERNAL ELECTRIFICATION:- Taking down carefully unsv aluminium / copper conductor point wiring (light, fan, light socket, power socket) complete fitting such as switches, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Point wiring with 1.5 Sqmm (Nominal dia) single core multi stranded copper conductor FRLS insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked terminated into CI/pressed steel terminal boxes not less than 1.6mm thick including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc for one light/fan/bell point controlled by one, one way switch including cutting chases and making good to disturbed surfaces of wall / ceiling / floor including treating with existing finishes, complete all as specified and as directed.

All as per item No. 05 above but for 3 pin 5 Amps on same board with cable 1.5Sqmm size, all as specified and directed

All as per srl item No-05 but for one 3 pin socket outlet 6 amp independent complete all as specified.

Point wiring with 2.5 sqmm (Nominal dia) FRLS PVC insulated sheathed multi stranded copper conductor, 1100 Volts grade for 3 Pin socket outlet 15 Amps on independent board through MS conduit medium duty (ISI Marked) concealed with accessories such as elbow, tees,internal & external bend etc. of suitable size including MS pressed steel cadmium plated terminal box of 1.6 mm thick for mounting switch socket combination and 3 mm thick ISI marked laminated sheet top cover including continous earth wire FRLS PVC insulated 2.5 Sq mm copper multi stranded conductor, 1100 Volts grade, connecting to common earth and earth dolly complete all as specified and directed.

Switch piano flush type 5/6 Amp single pole one way, (ISI marked), complete all as specified.

3/5 pin socket outlet 5/6 amp, complete all as specified and directed.

Switch piano flush type 16 Amp single pole one way, (ISI marked), complete all as specified.

Socket outlet multipurpose combination 2-in-1 3 pin, 6 & 16 Amps flush type universal complete all as specified. directed.

Supply and Fix in replacement Ceiling rose (ISI Marked) 3 Phase PVC/poly carbonate, insulated body, compete all as specified.

Supply and Fix in replacement Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed.

Supply and Fix in replacement LED lamp 9W, complete all as specified and directed. Make:- Crompton Cat Part No LED 9W - B22 - CDL or Equivalent cat part of make as specified in Appx 'F' here in after.

Supply and fix in replacementTube light fitting box type suitable for LED 18-20W tube Rod with end cap made out of CRCA sheet powder coated complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting including 18-20 watt LED tube rod 4 feet long complete all as specified and directed. Make:-Crompton Cat Part No:-LTT8-20 for LED tube rod & DMLN1LT8-16 for fittings or Equivalent cat part of make as specified in Appx 'F' here in after. Note :- The LED batten and LED tube rod shall be of same make as approved by GE.

Supply and fix in replacement Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 4 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning with & including taking down old unsv DBs complete all as specified. Make:- Legrand cat part No-5076 20 or Equivalent cat part of make as specified in Appx 'F' here in after.

Supply and fix in replacement MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series fixed in repair, complete all as specified. Make:- Legrand cat part No-4085 87 to 4085 95 or Equivalent cat part of make as specified in Appx 'F' here in after.

Supply and fix in replacement MCB single pole and neutral 6 to 32 amps 240 volts 10 KA 'C' series all as specified. Make:- Legrand cat part No-4086 09 to 4086 17 or Equivalent cat part of make as specified in Appx 'F' here in after.

Sub main wiring with single core cable 2x 4 sq mm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including 20mm rigid PVC conduit (Concealed) medium grade alongwith 1x 2.5 Sq mm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface, complete all as specified and directed. Note:- 2 wire of 4sqmm, 1 wire of 2.5qmm and one run of PVC conduit shall be measured as one unit.

Exhaust fan 300 mm sweep, heavy duty, single phase AC 230/240V 50 Hz AC, with energy efficient motor ,pre-lubricated double ball bearing ,speed 1400 RPM, complete with louvers for wall mounting incl cutting holes, grouting, holding down bolts, nuts, washers and provision of flexible PVC insulated copper conductor cable 3 core 0.75 sqmm from ceiling rose to exhaust fan complete all as specified and directed. Make: Havells, Cat Part No. Ventil Air-DS or its equivalent cat part of make as specified in Appx 'F' here in after.

B & R Portion Taking down cement plaster of any description on brick work including terrazo topping or tiles, racking out jointing hacking for key scrubbling down with water and removing all the demolished material outside cantt area, complete all as specified.

Dismantling floor, hearth, or wall tiling (Terrazzo / PCC / Ceramic Tiles) including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing unserviceable material outside cantt area, complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for including separating, scraping and cleaning of reinforcement and removing unserviceable material outside cantt area, complete all as specified and directed.

Taking down chowkhats or frames with shutters (w/o taking off shutters from the frames ) exc 1.5 Sqm and not exc 4 sqm each, including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish without any extra cost to Govt), & removing from site all as specified and directed by Engr-in-charge

Taking down chowkhats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5Sqm each including cutting holes for taking out holdfasts or dismantling brick work (holes cut and any other damage to jambs, walls for taking out holdfasts shall be finished identical to existing finish without any extra cost to Govt) & removing from site, complete all as specified.

Rendering 15 mm thick plaster in CM 1:6 on brick wall surface or concrete surface finished the surface even and fair without using extra cement upto any height of four story bldgs, complete all as specified.

Rendering 10mm thck in CM 1:3 or Plain Cement Concrete 1:2:4 type B-1 as in ceilings or concrete surfaces such as chajjas, upward fascia, downward fascias and similar items finished even and smoth including dubbing coat without using extra cement upto any height including all necessary scaffolding, complete all as specified.

Pressed steel frame of size 105x60mm for doors with single rebated including mild steel hinge medium weight 100 mm long and 25x3 mm flat iron in holdfast, tie bar all necessary fixing arrangement complete all as specified.

40mm thick, flush shutters, soild core construction, with particle block board core and plywood face panels commerical type both faces is covered with decorative face veneer with lipping/frame to match and complete all as specified & directed.

Anodised aluminium window and ventilator shutters powder coated (Thickness of powder coating not less than 50 micron) , side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminiumsnap beading, screws, complete all as specified and directed.

Anodised aluminium three track frame for doors,windows, ventilators powder coated (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

Butt hinges, medium weight, cold rolled mild steel, 100 mm size, complete all as specified & directed.

200 mm long aluminium anodised barrel tower bolt of extruded section ISI marked complete all as specified and directed.

Aluminium handle ,cast type, anodised of size 150mm long, complete all as specified.

Foor door stopper of aluminium alloy body and tongue 140mm anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

Rolled mild steel structural works as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam,tee,angle, channel or flat sections) including distance pieces, cleats etc Fe 410W(Gde E-250), quality 'A' complete all as specified.

Non skid ceramic coloured designer seamless tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed.

Non skid ceramic coloured designer seamless tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exc 0.18 sqm, in skirting / dado etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including 10mm thick plaster in CM 1:3, complete all as specified and directed.

Granite stone slab 16 to18mm thick (PURE BLACK) (table rubbed and polished) as in steps, jambs, pillars, wall linning (veneering to wall) window cills cooking platforms and like in cement mortar 1:3 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite laid over & including 15mm thick screed in CM 1:3 & making edges of slab to be rounded from all sides (including cutting and polishing), complete all as specified.

Plain cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs and as in benching and similar work including necessary form work, complete all as specified.

Sheet glass ordinary quality, 5.5mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified.

RCC nominal mix 1:2:4, type, B-1 (using 20mm graded crushed stone aggregate), as in slab supported on walls, columns in floors, roofs, landings, balconies and in shelves, complete all as specified.

TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for column, hooking ends and binding with and including mild steel wire(annealed) not less than 0.90mm dia complete all as specified.

TMT bars 6 to 8 mm dia as in in stirrups, spacers and binders cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking end and binding with and including mild steel wire(annealed) not less than 0.9 mm dia or securing with clips, complete all as specified.

Form work to soffits of suspended slab such as roof slab, manhole cover n exc 200mm thick horizontal or sloping rough finished surfaces and the similar work complete all as specified and directed.

Complete removal of existing treatment and applying two coats of cement base paint on walls including preparation of old plastered or un-plastered surfaces of wall complete all as specified & directed.

Preparation of newly plastered surfaces of wall and applying two coats distemper oil emulsion laid over & including a coat of wall care putty not less than 3mm thick, complete all as specified.

Preparation of newly plastered surfaces and applying three coats of white wash on ceilings, complete all as specified.

Applying two coats of synthetic enamel paint over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and as directed.

Preparation of old painted or undecorated surfaces of wood or wood based surfaces of any description exc.10 cm. in width or girth and applying one coat of synthetic enamel paint, complete all as specified.

Comprehensive maintenance of Electric Passenger Lift :- Comprehensive maintenance including preventive and periodical maintenance of installed lift in reliable, safe, efficient operating condition through authorised OEM or their accredited / authorised agencies by regularly examining, lubricating and adjusting the eqpt and carrying out planned maintenance in a systematic and controlled manner using technician and expertise and replacement of all unserviceable parts / items as per OEM terms & conditions and schedule of maintenece provided by the OEM including machine and belt. The following Equipments/activities are to be carried out in the comprehensive maintenance of the Lift :- (i) Renew all wire ropes and chains (where fitted) as often required an adequate factor of saftey, to equalise the tension on all hoisting ropes, repair or replace conductor cables and hoistway and machine room elevetor wiring, machine, worn gear, thrust bearings, drive sheves, drive sheaves bearings, break contact, lining and components. Item contd/--- to 53.01

(vi) Deflectors or secondary sheave, bearing, car and counter weight guide rails and buffers, top and bottom limit Switches, governor tension sheave assembly, compensating sheave assembly, car, counterweight and counterweight guide shoes including rollers or gibs, interlocks on hoistway door, hoistway door hangers, guides, automatic power operated door operator, car door hanger, car door contact, safety shoe, load weighing equipment, car frame, car safety mechanism and plateform. (vii) Battery operated emergency light and alarm system, wiring of all eqipments and accessories, vibration materials, reverse phase relays, over load warning indicator and digital group indicator panel with micro-processer complete and automatic rescue device incl maintenance free battery. Item contd/--- to 53.03

Notes:- 1. Item No 53 shall be operational only after expiry of defect liability period. i.e. after two years of date of completion of Phase - I . 2. The cost of material & qualified technician to attend the complaint on requirement basis including sunday and holiday as directed by Engineer-in-Charge. 3. The maintenance and replacement of spares shall be carried out by authorized representative of OEM and cost of the same is deemed to be included in the rates as quoted by contractor. 4. The contractor during the term of this contract shall maintain a reasonable supply of frequantly used replacement parts and lubricants to meet the requirements of the Unit. 5. The contractor shall examine periodically the safety devises and governor of the lift to ensure users safety. In addition the contractor shall conduct annual load safety test.

N K BUILDERS