PROVISION OF FALSE CEILING, GLASS PARTITION AND GLASS DOOR AND VARIOUS WORK AND DIGITAL WALL TILE ON BOUNDARY WALL WITH GATE AND FLUSH LIGHT, PRESSURE AND BOOSTER PUMP AND REPLACEMENT OF DOOR AT INS NETAJI UNDER GE (I) (CGN) KOLKATA

Amount

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and as directed

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed

Supply and fixed solid PVC door frames of size 50 mm x 47 mm made out of 5 mm thick wood grain printed PVC sheet and edge will be printed to match with printed sheet reinforced with MS square tube all as per specification & drawing complete all as specified and directed by Engineer in charge.

Supply and fixed factory made solid PVC moulded door shutter, 28 to 30 mm thick (stiles) with particle board core, with 2, 4, or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing.

Supply and fixed medium weight stainless steel butt hinges, 100 mm size, naturally finished bright with smooth surface without chemical coating complete all as specified and as directed.

Supply and fixed aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 150 mm long, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed.

Supply and fixed cast aluminium alloy handle, cast type, 150 mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.

Supply and fixed aluminium alloy sliding door bolts with hasp, staple and fixing clips of sheets, or extruded sections and fixing bolts and sliding bolts of extruded sections of aluminium alloy, 250 mm long, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.

Supply and fixed entrance glass door / partiton wall with 12mm thick toughened glass and necessary unit insignia embossed on glass on frosted surface all as approved by GE including fixed to existing glass portion with all fixture and fittings etc complete all as specified and as directed.

Supply and fixed steel handle 300 mm long, fancy type, including necessary fixing screwd complete all as specified and as directed,

Supply and fixed mortice lock, vertical type, mild steel, 4 levers, vertical type, 100 mm size including protective coating of painting fixed in position complete all as specified and directed.

Supply and fixed double action concealed type floor springs (hydraulically regulated) made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel top cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed.

Supply and fixed powder coated, minimum thickness 50 micron, aluminium sections for doors, windows, ventilators, partition wall including fabrication of frame shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc. including all accessories such as glazings clips, and rubber beadings for fixing glass panes in frame complete all as specified. Note : (i) Glass panes, wire mesh & handle will be measured & paid separately . (ii)The quoted rate shall be inclusive of cost of rubber beading however it will be not be weighed and not paid separately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rate.

Material and labour for powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section (thickness of powder coating not less than 50 micron) weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws etc. complete all as specified and as directed.

Supply and fixed anodised aluminium grill, having mess size 100 mm x 100 mm made up of the 40 mm wide and 3 mm thick aluminium section fixed with the MS hoock of 6 mm round bars two number in each side insert into the jamb/cill complete all as specified and as directed.

Supply and fixed exposed type hydraulically regulated door closers, universal closer, bottle type (type A), Designation No. 1, suitable for upto 35 kg mass of doors & upto 700 mm width of door, cast iron non porous body and black plate, cast iron piston or pack piston/ pillion, painted and finished with lacquer in colours as per IS 3564: 1995 complete all as specified and as directed.

Demolition of wall/ ceiling boards(fibre pulp insulation etc.) or insulations boards /slabs/blankets any thickness including cover fillets of any description including all snap grids and hanging arrangements complete all as specified.

Material and labour for GI frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having urled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the ntermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

Material and labour Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat and curved surface over metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately all as specified.

Supply and fixed interior decorative cavity / hollow PVC wall panelling of interlocking types thickness 8mm- 10mm width n ex 255mm with wood colour/ texture as approved including necessary trims where required fixed with hidden screw to GI seamless framework complete all as specified and as directed.

Material and labour Gl frame work for seamless wall panelling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with complete all as specified and as directed.

Supply and fixed seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with pecially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid eparately) complete all as specified and as directed.

Supply and fixed prelaminated particle board (decorative lamination on both sides), 12 mm thick, grade I or II & type II (Designation PLB-12 or PLB-22), made out of medium density particle board (flat pressed-three layer or multilayer and graded (grade I or grade II), bonded with BWR adhesive), fixed with screws to timber/ steel frame work for horizontal applications as in table tops, counter, furniture tops, etc. complete all as specified and as directed.

Supply & fix sheet glass, ordinary quality, 4.8 mm thick and glazed with oil putty or fixed with beads in square exceeding 0.5 Sqm in each pane complete all as specified and directed.

Supply and fixed stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

Material and labour for preparation of new or previously untreated plastered/ gypsum ceiling surfaces and applying two coat of oil bound distemper over a coat alkali resistance primer complete all as specified and as directed.

Material and labour for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Material and labour for ceramic fully vitrified tiles, coloured ceramic floor tiles (group B Ia), 600 mm X 600 mm X 10 mm in floors including 15 mm thick screed bed or bedding layer in cement mortar(1:6) set and jointed in neat cement slurry and pointed in epoxy mortar to match complete all as specified and directed.

Material and labour for ceramic fully vitrified tiles, coloured ceramic floor tiles (group B Ia), 600 mm X 600 mm X 10 mm in skirting's/ vertical surfaces laid including 10 mm thick backing coat in cement mortar(1:4) set and jointed in neat cement slurry and pointed in epoxy mortar to match all as specified and directed.

Material and labour for printed glazed ceramic tiles in verticle surface, 450 mm x 300 mm x 7 mm thick set and jointed in neat cement slurry and pointed in white cement or colour cement to match the surface including 10 mm thick plaster in cement mortar 1:4, as backing coat complete all as specified and as directed.

Material and labour for non skid, rectified, colour ceramic floor tiles (group B II), 300 mm X 300 mm X 7 mm thick in floors including 15 mm thick screed bed or bedding in cement mortar(1:4) set and jointed in neat cement slurry and pointed in epoxy mortar to match complete all as specified and as directed.

Material and labour for 25 mm thick insulated PVC wall lining consisting of PVC insulated panels having expanded polystyrene (EPS) stuck to 2 mm thick plain colour PVC sheet duly fitted into the wall, shelves, partition etc. as per specifications and drawing complete all as specified and as directed.

Material and labour for 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed.

Supplying and laying CPVC pipes for potable hot and cold water distribution, nominal size 20 mm, pressure class 1, SDR 11 including plain CPVC fittings of pressure class 1, SDR 11 in trenches complete all as specified and as directed.

Supply and fixed CPVC special transition fittings, elbow/ Tee/ socket/ reducing socket MBTA/ FBTA/ Unioun/ Adapter etc. with brass threading, 20 mm nominal size complete all as specified and as directed.

Supply and fixed in repairs vitreous china squatting pan, 'Orissa" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S' trap, front or back inlet and integral foot rests, any pattern and including fixing bolt, connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge.

Supply and fixed in repairs 10 litres capacity, low level, syphonic type, white, vitreous china flushing cistern as per IS 774: 2004 with inlet, ball valve, float and handle including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed.

Supply and fixed in repairs wash basins, vitreous china, white, flat back, size 550 mm X 400 mm with and including cast iron brackets (embedded in wall upto 110 mm depth with and including cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate or fixing on wall with and including rawl plug and screws), 32 mm nominal size, copper alloy, nickel chromium plated finish waste fittings, including painting of fittings and brackets, sealing gap between wall and basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste pipes, waste fittings etc. with silicone sealant complete all as specified and as directed.

Supply and fixed in repairs 15 mm nominal size, nonrising spindle type fancy angular stop cock, as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed.

Supply and fixed 15 mm nominal size, nonrising spindle type fancy bib taps as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, bright finish complete all as specified and as directed.

Supply and fixed brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and as directed.

Supply and fixed sheet glass shelf assembly consisting of 5.50 mm thick glass sheet shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed.

Supply and fixed in repairs chromium plated grating 100 mm round fixed on floor / Nahani trap fixed with 1:1 cement mortar complete all as specified and as directed

Supply and fixed 15 mm nominal size, nonrising spindle type fancy pillar taps as per IS 8931: 1993, cast copper alloy body with knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed.

Supply and fixed in repair 32/40 mm dia 800 mm long PVC corrugated waste pipe fixed to walls complete all as specified and as directed

Material and labour for PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

Supply and fixed in repairs health faucet with jet spray, 1.5 metre long, cast copper alloy, nickel chromium plated finish, 15 mm bore, 100 mm long with 1.5 metre long stainless steel shower hose and mounting device attached to wall complete all as specified and as directed by Engineer-in-Charge.

Taking down cement plaster on stone/brick/concrete surfaces including racking out joint, hacking for key, scrubbing down with water complete all as specified and as directed.

Material and labour for plastering 15 mm thick on fair faces of brick work or concrete surfaces (on vertical surfaces) in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over one coat of alkali resistant primer over putty to match the existing surfaces complete all as specified and as directed.

Supply and fixed in repairs 25 mm dia stainless steel curtain rod with catrip type hoock and bracket fixed on wall complete all as specified and as directed.

Material and labour for precast cement concrete 1:2:4 type B1 using 20 mm nominal size graded crushed stone aggregate in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling). corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) complete with joints to match complete all as specified and as directed.

Material and labour 50 mm thick plain cement concrete 1:3:6 type C2 using 40 mm nominal size graded stone aggregates finished surface even and fair as in plinth protection all as specified and as directed.

Supply and fixed cast iron, sand cast, socket and spigot, nominal dia 100 mm soil, waste and vent pipe as per IS 1729: 2002 in any length with cement joints, fixed to walls complete all as specified and as directed.

Supply and fixed cast iron branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches without access door for soil, waste and vent pipes of nominal size 50 mm complete all as specified and as directed.

Supply and fixed cast iron bends (any radius) with duck's foot or heel rest (larger bore measured) without access door for soil, waste and vent pipes of nominal size 50 complete all as specified and as directed.

Material and labour for excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes cable trench, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Material and labour for Plain cement concrete 1:4:8 type D2 (using 40mm graded aggregate) in foundations, filling and mass concrete complete all as specified and directed.

Material and labour for brick work with fly ash bricks, straight or curved on plan, exc 6m mean radius built in cement mortar 1:4 complete all as specified and as directed.

Material and labour Rendering 15mm thick CM 1:4 on fair faces of brick work or concrete surfaces is to be finished even and smooth without using extra cement complete all as spefied.

Material and labour Rendering 10mm thick cement mortar 1:4 on fair faces of brick work or concrete surfaces is to be finished fair and even as backing layer complete all as spefied.

Material and labour 16-18 mm thick ZED BLACK granite slab machine cut in colomn, etc laid over cement screed and jointed with grey cement with admixture of pigment to match the shade of granite stone including frinding and polishing complete all as specified and directed.

Supply and fixed 75mm thik precast RCPC cover slab size 600 mm x450 mm of 10MT load bearing capacity with embosing RCPC 10MT set in collers complete all as specified and as directed including taking out old one.

Material and labour for STAINLESS STEEL WORD made up of the 1.5 mm thick SS plate and size not less than 200 x 35 x 25 mm and fixing on wall or any location as directed by Engineer-in-Charge with screwing , fixing to the wall with suitable adhesive material. Letter size and pattern shall be as approved by GE complete all as specified and as directed.

Supply and fixed for three dimentional stainless steel letter in golden coated for writting the "NAVAL OFFICER INCHARGE (WBG)" and fixed on the wall, size of letter 12" height with back side LED light, including background ACP box of suitable size for fixing the letters on wall complete all as specified and as directed.

Supply & stacking of good earth (Fresh garden soil) at site and carriage with any lead complete all as specified and directed. (Note :Earth measured in stack will be reduced by 20% for voids for payment).

Supply & stacking of farmyard manure at site and carriage with any lead complete all as specified and directed (Noted :Farmyard manure measured in stack will be reduced by 8% for voids payment)

Material and labour for planting and developing lawn grass (Phospolen) including following (i) Preparing of soil base by excavation/ploughing and loosening of ground upto 15 cm and removing unwanted material, grass stone etc to a distance exceeding 50m but not exceeding 250m. (ii) Mixing good earth (fresh garden soil) & farm yard manure thoroughly in 21 proportion and filling excavate area to a height of 15cm and levelling including suitable quantity of oil cake, bone dust, anti-termite powder completely (iii) Watering on previous night and planting required variety of lawn grass and maintaining for a minimum of defect liability period of well-established lawn grass whichever is later blanket to the satisfaction of Engg-In-Charge by watering, weeding clipping and rolling etc complete all as specified and as directed.

Material and labour for planting and developing different type hedge plants naming alternanthera, codiacum etc including following:- (a) Preparing soil base by excavbation/ploughing and loosening of ground upto 30cm and removing unwarnted material, grass stones etc to a distance exceeding 50m but not exceeding 250m. (b) Mixing good earth (fresh garden soil) & farm yard manure thoroughly in 3:1 proportion and filling in excacation area to a height of 30cm and leveling completedly . (Note :- good earth (fresh garden soil ) & farm yard manure shall be measured and paid for separately). (c) Watering on previous night and planting cutting of required variety above plants at required spacing so as to form cover on planted area after full grouth and maintaining for a minimuim period of 180 dahys or till formation of well develop plants whichever is later to the satisfaction of Engr-in-Charge by wagering weeding, cliping and rolling etc complete.

Material and labour for planting different group palm plant commonly used for area beautification or landscape including following :- (a)Digging hole of size 600mm dia x 600 mm depth, removing & conveying excavated soil to a distance exc 50m and not exceeding 250 m. (b)Filling the hole with fresh garden soil and farm yard manure in 3:1 proportion upto a height of 0.6m levelling, suitable quantity of oil cake, bone dust, anti termite powder and watering as specified and approved by Engr-in-charge and maintaining for a minimum period of 180 days or till formation of well established plants whichever is later complete all as directed. Note:- Good earth (fresh garden soil) & farm yard manure shall be measured and paid for separately.

Demolition of RCC platform n exc 15 cm thickness (below or above ground floor complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for comlete all as specified and as directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Material and labour for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

Material and labour Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Material and labour for Reinforced cement concrete M-25 (Design mix) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs, under-reamed piles and mass concrete complete all as specified and directed. Note:- (i) Reinforcment and formwork shall be measured and paid separatly. (ii) Design mix shall be used as per running contract of CE's at this office.

Material and labour for Reinforced cement concrete M-25 (Design Mix) as in Columns, pillars, piers, posts and struts complete all as specified and directed. Note:- (i) Reinforcment and formwork shall be measured and paid separatly. (ii) Design mix shall be used as per running contract of CE's at this office

Material and labour for Reinforced cement concrete M-25 (Design mix) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed. Note:- (i) Reinforcment and formwork shall be measured and paid separatly. (ii) Design mix shall be used as per running contract of CE's at this office

Use & waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter as in fair finished surface all as specified and directed.

Use & waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions as in rough finished surface all as specified and directed.

Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders etc. as in rough finished surface all as specified and directed.

Material and labour Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

Material and labour Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

Material and labour exterier digital ceremic wall tiles, of size 450x300 mm , set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick backing coat in cement mortar (1:4), complete all as specified and as directed.

Material and labour for 16-18 mm thick granite (or any type ) tiles machine cut in skirting/ dado laid over cement screed and jointed with grey cement with admixture of pigment to match the shade of granite stone including grinding and polishhing complete all as specified and as directed.

Supply and fixed posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. embeding in concrete and screwing etc. including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Supply and laying double wall corrugated pipe, internal dia 25 mm confirming to IS:16205:2018 (Part 24) with coupler and all fittings as in floor ortrenches or fixing on wall, ceiling for protection of LT cable complete all as specified and as directed.

Material and labour for cement concrete 1:3:6 type C1 using 20 mm nominal size coarse aggregate in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

Material and labour for preparation of new steel surfaces of any description over 10 cm in width or girth not otherwise described, applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome all as specified and directed.

Supply and fixed galvanized 2 strand steel barbed wire 2.24mm dia barbed wire with 2mm dia barbs at 75mm spacing stringing, tightening and fixing to MS nibs embeded in MS fencing post etc securing and tying as crossing with and provision of galvanized mild steel wire, staples or steel pins etc. complete all as specified and as directed. (each line wire to be measured).

Supply and fixed MS seccon concertina coil 600/750mm dia (before stretching) with 10-12 stands of SRPBT wire of minimum dia 2.59 mm, tensile strength of 1620 N/sqm m with anticorrosive mint green paint conforming IS-513DD grade & IS-4454 part-I/1981 grade-II, for respective materials of razor strip & core wire and all fixing arrangements as per manufactures instruction for fixing & erection complete all as specified and as directed.

Material and labour for Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in soft/loose soil complete all as specified and directed.

Material and labour 20 mm graded aggregate type B1 lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

Material and labour Broken glass coping on top of walls complete all as specified.

Material and labour Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete including all Orinamental work conforming to Fe.290.Gde-E-165 all as specified

Surface Excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and as directed.

Removing exacavated material n.exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and as directed.

Material and labour for Cement concrete 100 mm thick Type C1 (1:3:6) 20 mm graded stone aggregate as in floor finish concrete surface even and rough finish to receive topping layer.

Material and labour for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed with grey cement and pigment and pointed in neat cement slurry in floors including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

Material and labour Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 100 mm thickness M-50 Grade With Grey cement and pigment complete all as specified and as directed.

Material and labour for concealed point wiring for one light or one fan or one exhaust fan controlled by one switch complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 1.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 1.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and as directed. (Note: Cost of cutting chase and making good shall be included in quoted rate.)

Material and labour for concealed point wiring for one light controlled by two 2-way switches complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 1.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 1.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and as directed. (Note: Cost of cutting chase and making good shall be measured included in quoted rate).

Material and labour for concealed point wiring for one 3 pin/ 5 pin 5 Amps socket outlet on independent board complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 1.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 1.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and as directed. (Note: Cost of cutting chase and making good shall be included in quoted rate).

Material and labour for concealed point wiring for one 3 pin/ 5 pin 5 Amps socket outlet on the same board complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 1.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 1.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and as directed. (Note: Cost of cutting chase and making good shall be included in the quoted rate).

Material and labour for point wiring for one 3 pin/ 5 pin 15 Amps socket outlet on independent board complete with and including single core PVC insulated, unsheathed flexible conductor FR-LSH cables 4 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through & including medium protection stove enamelling rigid steel conduit as per IS 9537 (Part-II): 1981 of suitable nominal size as required at site dia but not less than 20 mm nominal size including all accessories/ fittings/ junction boxes/ inspection cover etc. ISI marked and sunk terminal boxes flush galvanised metal boxes suitable for fixing with 2.5 sqmm copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable as continuous earth wire connected to metallic body at one end and common earth dolly to other end complete all as specified and as directed.

Supply and fixed recessed full open 2ft x 2 ft tile, glare free uniform illuminination with longer life and less maintenance, 24 W with minimum lumrn capacity 100 lumen/watt complete all as specified and as directed.

Supply and fixed asthetically designed 2 x 2 Led flat panel surface mounted, glare free, uniform illuminination with longer life and less maintenance, 18 W with minimum 100 lumen/watt complete all as specified and as directed.

Supply and fixed wall mounted fan, AC, 50 Hz, single phase, 230 V, 400 mm sweep, 1350 rpm, 4 Nos plastic blades, Insulation Class A including capacitor to ensure power factor more than 0.9 complete all as specified and directed by Engineer-in-charge.

Supply and fixed modular switch, 1 way, 6 A, 1 module complete all as specified and as directed.

Supply and fixed modular switch, 2 way, 6 A, 1 module complete all as specified and as directed.

Supply and fixed Modular fan regulator, 120 W, 2 modules complete all as specified and as directed.

Supply and fixed modular switch socket combination, 3 modules with 3 pin socket outlets, 6A, 240 V, AC, 50 Hz with earthing contact, rewirable, pillar type terminal, normal protection, unenclosed, without Shutter, Flush type, Design B and switch, 6 A, single pole, one way, 240 V, AC, 50 Hz, ordinary (IPXO), normal gap construction, unenclosed, flush type, screw type terminals, pattern no. 1, rocker type, design A complete all as specified and as directed.

Supply and fixed (3 pin and 2 pin) combined modular socket outlets, 6A, 2 modules, 240 V, AC, 50 Hz with earthing contact, rewirable, pillar type terminal, normal protection, unenclosed, without Shutter, Flush type, Design B complete all as specified and as directed.

Supply and fixed (3 pin and 3 pin) with common earthing pins, combined modular socket outlets, 6A & 16A, 2 modules, 240 V, AC, 50 Hz with earthing contact, rewirable, pillar type terminal, normal protection, unenclosed, without Shutter, Flush type, Design B complete all as specified and as directed.

Supply and fixed modular switch, 1 way, 16 A, 1 module complete all as specified and as directed.

Supply and fixed single pole blanking plate in DBs of MCB complete all as specified and as directed.

Supply and fixed ceiling roses, 6A, 240 V, surface type, intended to support mechanical loads by means of flexible cord, having provision for the connection of switch wiring, screw type terminal, made out of Polyamide or hornbean complete all as specified and as directed.

Supply and fixing 6 module flush mounted with starter DP MCB & Plug Top with indicator and all fixing arrangement including taking down old once complete all as specified and as directed.

Supply and fix metal flush box 1 or 2 module complete all as specified and as directed.

Supply and fixed modular white cover plate with frame, 1 module complete all as specified and as directed.

Supply and fixed modular white cover plate with frame, 2 modules complete all as specified and as directed.

Supply and fix metal flush box 3 module complete all as specified and as directed.

Supply and fixed modular white cover plate with frame, 3 modules complete all as specified and as directed.

Supply and fix metal flush box 4 module complete all as specified and as directed.

Supply and fixed modular white cover plate with frame, 4 modules complete all as specified and as directed.

Supply and fix metal flush box 6 module complete all as specified and as directed.

Supply and fixed modular white cover plate with frame, 6 modules complete all as specified and as directed.

Supply and fixed round shape 6 watt AC recessed type with high efficiency PMMA diffuser soft glare free light complete with deiver, holder, LED lamp suitable for roof ceiling including connecting with three core flexible copper conductor cable complete all as specified and as directed.

Supply and fixed round shape 15 watt AC recessed type with high efficiency PMMA diffuser soft glare free light complete with deiver, holder, LED lamp suitable for roof ceiling including connecting with three core flexible copper conductor cable complete all as specified and as directed.

Supply and fixed 10 Watt LED Bollard Vertical Cone light, warm white, die aluminium cast, opal diffuser with in-built LED light with IP 65 protection complete all as specified and as directed

Supply and fixed concealed sub main wiring complete with and including two Nos single core PVC insulated, unsheathed flexible conductor FR-LSH cables 2.5 sqmm as per IS 694: 2010, ISI marked, annealed, multistranded copper conductor drawn through and including medium mechanical stresses class PVC conduit as per IS 9537 (Part-III): 1983 of suitable nominal size as required at site dia but not less than 20 mm nominal size including all accessories and fixed on walls and 2.5 sqmm one No single core copper conductor PVC insulated, unsheathed flexible multistranded copper conductor FR-LSH cable for earthing and connected to common earth dolly complete all as specified and directed by Engineer-in-charge. (Note 1- Two runs of 2.5 sqmm cable, one run of 2.5 sqmm cable and one run of conduit shall be measured and paid as one unit length. Note 2- Cost of cutting chase and making good shall be included in the quoted rate).

Supply and fixed 12 watt wall washer LED light, die cast aluminium housing, transparent tampered glass, matt grey finish, LED warm white light with IP54 protection complete all as specified and as directed.

Supply and fixed post top lantern LED light, 40 watt, 230 V AC outdoor type with decorative post top for 360 degree indirect light with IP 65 protection, impact and corrosion resistant complete with driver, and lamp complete all as specified and as directed.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated cable for working voltages of 1100 V, PVC sheathed, armoured, 4 core, nominal cross sectional area of main conductor 10 sqmm, stranded aluminium conductor, ISI marked as per IS 7098(Part-I): 1988 including cable glands, lugs etc. to suit the cable size and to be laid in trenches, fixed along pole, under floors, through GI pipe laid under floors/roads, through concealed GI pipe along wall etc. complete all as specified and as directed.

Supply and fixed sheet metal enclouser, TPN, double door, 4 way with suitable size of bus bar with provison of MCB incomer complete all as specified and as directed.

Supply and fixing 415 V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed.

Supply and fixing 415 V, 10 KA 'C' curve miniature circuit breaker (MCB) of four pole and current carrying capacity 16 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and as directed.

Supply & spreading in trenches dry river sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly.

Material and labour for laying of bricks locally available sub class 'B' bricks (old size) for cable protection cover laid flat and dry in trenches over the cablfCe perpendicular to the direction of cable all as directed.

Material and labour for 80 mm dia GI pipe, light grade, including all fitting as in trenches/ wall to fixed for protection of cable complete all as specified and as directed.

Supply and fixed 0.5 HP, single phase, 2300-400 LPH discharge at 5-40 meter head, Heavy Duty Self priming Pumps complete all as specified and as directed.

Supply and fixed 1 HP, single phase pressure booster pump with automatic pressure controller complete all as specified and as directed.

Supply and fixed 2 HP single phase, priming pump complete all as specified and as directed.

Supply and fixed automatic water level controller and indicator with float valve complete all as specified and as directed.

Supply and fixed motor staer suitable for 2 HP centrifugal pump complete all as specified .

Material and labour for earthing complete with galvanised steel plate earth electrode 600 mm X 600 mm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to earthing lead of 4.0 mm dia galvanised mild steel wire by means of bolts, nuts, check nuts and washers of galvanised iron from earth plate to test point upto 7.5 metre including all as shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete chamber in cement concrete M15 (Nominal Mix) using 20 mm nominal size coarse aggregate, precast RCC cover slab in cement concrete M15 (Nominal mix) using 20 mm nominal size coarse aggregate of size 40 cm X 40 cm X 5 cm reinforced with 8 mm dia TMT bars @ 150 mm c/c with one handle for lifting made out of 8 mm dia bar, GI funnel, GI wire mesh filter, 20 mm dia GI pipe medium grade for watering, 20 mm dia GI pipe medium grade for protection of earthing lead, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil/ strata and testing complete all as specified and as directed by the Engineer-in-charge.

M/s Santosh Industrial Corporation

Tirupati Buildcon Pvt. Ltd.

Ultimate Solution Company

RUNGTA STEEL CORPORATION

S M ENTERPRISE

KT CONSTRUCTIONS