SWR-SBC Division-Provision of 01 additional loop line on Road-1 side at NDV station of of Bangalore Division.

A-SOR-2011 items

B-SOR Supply items

C-SOR Execution items

D-SOR Supply and installation items

F-SOR UFSBI and RTU items

B1-Non SOR Supply items

Supply of 19"- 42U Rack complete with fittings for housing SDH equipment,FDMS, DDF and other equipment like cable managers, completely wired using krone module and other equipment s like runaway ladders etc.,as per technical specification below. It should be able to lock all theequipment with only order wire telephone outside the rack , the rackshould of APW President/ Rittal makeetc., The 1 components of the rack arespecified below. this includes transportation and installation of rackin prefab/building at specified stations.a. Rack S33 42U 600WX600D -1 no.b.fixed side panels 42U x 600 D - 2nos.c.Front glass door plain 42U/600W -1no. d. Rear MS dOOR pLAIN 42U/600W-1 no. e. Caster with brakes-2nos. f.Fans directly mounted on the top 48v Dc 90CFM -2NOS. g.Kronemounting bracket -01 No. h. MCB mounting panel with MCBS a)32 AmpsMCBs (DP) - 2 nos. b) 6 Amps MCBs(DP) -6 nos. i) earth continuity kit -o1nos j. Equipment trays-5 nos. k.channel with cable loops 42U-2 NOS.

Master Telephone with Voice Logging Facility for Electronic LC Gate Telephone system as per specification No : RDSO /SPN/TC -51/2011Revision 3.0 with amendment No 1 or latest. FIRMS MAKE/BRAND: BENTRON POWER SYSTEMS.

Supply of Power Supply Unit for Master Slave LC GATE Unit 12V/24V AS PER

Supply of VF Transformer (1120:470/1120:1120/470:470/470:600/1200:600 Ohm) as per Specification No. IRS-TC-76/2021 Ver 1.0 (Cylindrical type) or IRS/TC/22/ 2021 Ver1.1 (Rectangular type) with latest amendment.

Supply of Beetel M-75 or similar CID telephone with 16-Digital large back lit LCD display 10 one touch, 10 two touch memory CLI announcement features, 80 incoming and 50 outgoing call memory.

Supply of 20pair krone box

Supply of light weight 2W/4W portable Emergency control Telephone made of ABS plastic as RDSO spec.IRS :TC 78-2000 with amendment No.2 or latest

Supply of sealed maintenance free battery of 12V 75AH as per specification for VHF set

Supply of 10 way Krone modules make KRONE

Supply of UTP CAT-6 cable in a roll of 305 meterand make Siemen/ Systemax / Panduit/ Tyco/Krone/ AMP.

Supply of 0dB gain adjustable GP antenna for VHF set Model No:GM300/GM338/GM950 etc.

Supply of low loss RF coaxial cable RG217U with silver tipped connectors on both ends, 30 meters length.

Supply of Digital clock with GPS Synchronization suitable for office complex with Red lED (Standalone mode each clock with GPS receiver) as per RDSO Specification No: RDSO/SPN/TC / 62 / 2008 (Rev 3.0) with ammendment No:2 or similar.

Supply of Hylam sheet resin bonded 10mm thick of size 2400mm x 1200mm

Supply of GPS tagging featured cable route locator/tracer set suitable for detecting underground armoured optic fibre cable (OFC) and signalling cables with LCD graphic display active/passive modes and depth range 3m to 10m. Model STLOC10 GPS make Stanlay or equivalent.

Supply of Rodometer (DistanceRecorder) similar to Bosch Make Model No: 1011662 or better.

Supply of laser based Distance Reader similar to Bosch make Model No.GLM 100c laser range figer or better with blue tooth and all accessories.

Supply of class 'C' pluggable and testable type Surge protection Device for track feed battery charger with visual indication and potential free contacts suitable for up to 24-60V DC. AC application installation pattern L1-L2, L1- PE, L2-PE (one set consisting of three SPDs) specn No RDSO/SPN/165/2012 or latest(one set of two SPDs) VAL MS350VF ST+VALMS BE/FM. make phonoix or similar. acceptedbrand/make: HAKEL model noPIIIM-320 SDs/1+1.

PVC Copper Cable single core, Unsheathed cables with flexible Multi stranded copper Conductors of Cross Sectional Area of Conductor 6 sq.mm (FR) suitable on Working Voltage 1100V as per IS: 694:2010 latest (One bundle of 100 Mtrs.) (Colour: 0 coils Green, 50% coils red, 50% coils black)

Supply of 10 Sq.mm. Multistrand Single Core PVC insulated Copper Cable as per RDSO Specn. IRS : S-76/89 (Amdt. 3) or latest. Each coil to be of 100 mtrs length. (Colour: 0 coils Green, 50% coils red, 50% coils black)

Supply of copper cable ,PVC Copper cable 16 sq.mm single core multistrand cable (Colour: 0 coils Green, 50% coils red, 50% coils black)

Half Round RCC pipes & collars of 300 mm outer dia & 250 mm internal dia (2 meter long) along with collars as per IS No. 458/2003 of NP type.

Key Lock Checking Relay, AC Immune, Neutral Line, proved type, 24V DC with 4F/4B 23 contacts, front & back contacts metal to metal confirming to RDSO/SPN/219/ 2016 Ver.1(Amdt.1), IRS:S- 23/88 (Amdt 1), IRS:S@ 45"47@ 68 (upto Amdt 6) & IRS:S-46/74 (Amdt 1) or latest with different ward combinations. (Two extra ward plates for point machines to be supplied with each relay). Ward combinations shall be decided by the Railway Engineer at Site

Supply of Electric Point Machine 143 mm stroke (AC immunity 400V AC) completewith lock detector and slides for lock detector non-traiIable to operate on 110 VDC rotary locking with crank handle 24 universal type as per RDSO Spec. No. IRS:24/2002 (Amd.1) and RDSO Drg.No.S-10800 (Alt. 5) with junction box telescopic.The motor will be as per RDSO Spec.No.IRS:S-37/82 (Amd.3) with RDSODrg.No.S-10910. Note: It also includes supply of set of tools in a suitable toolbox along with every set of eight point machines.

Supply of Ground connections for 143mm point machine [LATEST ALTERATIONS IF ANY ARE APPLICABLE TO ALL DRAWINGS.]

ELECTRIC POINT MACHINE NON-TRAILABLE TYPE CONFORMING TO RDSO SPECIFICATION NO. IRS : S-24/2002 (AMENDMENT NO.1) WITH FOLLOWING FURTHER INFORMATION. (A). 220 MM THROW WITH INTERLOCKING FOR OPERATION OF POINT IN RAILWAY YARD AS PER RDSO DRG NO. S-11000. (B).TYPE OF GROUND CONNECTIONS WITH NYLON INSULATION CONFORMING TO RDSO DRG NO. S-3454 AND CLAMP POINT LOCK CONFORMING TO RDSO DRG NO.3395 FOR 60 KG THICK WEB SWITCH. (C).AC IMMUNITY LEVEL OF MOTOR FOR ELECTRIC POINT MACHINE SHOULD BE OF 400V (R.M.S) 50 HZ. THE EXTERNAL COLOUR OF 26 ELECTRIC MOTOR SHALL BE PAINTED WITH RED COLOUR." LATEST ALTERATIONS IF ANY ARE APPLICABLE TO ALL DRAWINGS. The following set of tools in a suitable tool box shall be supplied along with every set of eight point machines or less. i). Hand operated square drive socket wrenches of 12.5 mm driving square (short type) as per IS: 7381 for M8, M10, M12 & M18 threads. (One 250 mm long 12.5 mm square extension bar as per IS: 7991 along with compatible Tee handle Square drive as per IS: 7975 suitable for above socket wrenches shall also be provided.) ii). Open jaw wrenches (spanners) for M10, M12, M20, M24 & M33 threads as per IS: 2028. iii). Adjustable wrench. iv). Screw driver 300 mm long. 20.2 Junction box and two numbers of telescopic pipes of approved type shall be supplied as an integral part of the point machine.

Relay,Non AC immune, plug in type, style QN1, Neutral line 24 V DC 8F/8B contacts, front & 27 back contacts metal to carbon, complete with plug board retaining clip & connectors confirming to BRS:930, IRS:S-23/88 (Amdt 1) & IRS:S@45"47@68 (upto Amdt 6) or latest .The interlocking code for this unit shall be ABCDF

Relay, AC immune ,plug in type, style QNA1, Neutral line 24 V DC 8F/8B contacts, front & 28 back contacts metal to carbon, complete with plug board retaining clip & connectors confirming to BRS:931A, IRS:S-23/88 (Amdt 1), IRS:S@45"47@68 (upto Amdt 6) & IRS:S@45<47@78 (Amdt 1) or latest .The interlocking code for this unit shall be ABDGH

Relay, AC immune, plug in type, style QNA1K, Neutral line 24 V DC, 1000 Ohm, 6F/6B 29 contacts, front & back contacts metal to carbon, complete with plug board retaining clip & connectors confirming to BRS:931A, IRS:S-23/88 (Amdt 1), IRS:S@ 45"47@ 68 (upto Amdt 6), IRS:S@ 45<47@ 78 (Amdt 1) & RDSO/SPN/STS/E/Relays /UEA (PI) or latest .The interlocking code for this unit shall be CDEKY.

RELAY, AC IMMUNUE, PLUG IN TYPE, STYLE "QTA2", DC NEUTRAL TRACK, 9 OHM, 2F.1B CONTACTS, FRONT AND BACK CONTACTS METAL TO CARBON COMPLETE WITH PLUG BOARD, RETAINING CLIP AND CONNECTORS, CONFORMING TO BRS:939A, BRS:966 (APPENDIX F2), IRS : S-34 AND IRS:S - 23 (AMENDMENT UPTO DATE AS APPLICABLE). THE INTERLOCKING CODE FOR THIS UNIT SHALL BE FGHKX

Supply of Relay AC Immune plug un type style -QBCA1 DC based point contractor 24v DC 2F (H.D.) 4B contacts front contacts (heavy duty )and back contacs metal to carbon complete with plug board ,retaining clips & connectors . confirming to BRS 943,IRS S 34 &IRS S23 .pin code BCEJK

Supply of relay plug in type style QECX61 AC LED all aspect ac lamp proving relay unit with 32 inbuilt current transformer type slow to release neutral line relay 4F/4B contact metal to carbon suitable for working with 110v ac led signal lamp conferming rdso specification no- sts/e/relay/ac lit led signal/09/2002 amdt-1, brs:941A, irs:s:34 & irs:s-23. the interlocking code for this unit shall be ABDHK

RELAY FAIL SAFE ELECTRONIC TIME DELAY DEVICE, MOUNTED ON Q SERIES RELAY BASED AND COVERED WITH FIXED TIMING OF 60 SECONDS CONFORMING TO IRS-S-61-2000 WITH AMENDMENT NO.1 IRS-S-34 AND IRS:23 (AS APPLICABLE) OR LATEST. THE INTERLOCKING SHALL BE AFHKY

RELAY FAIL SAFE ELECTRONIC TIME DELAY DEVICE, MOUNTED ON Q SERIES RELAY BASED AND COVERED WITH FIXED TIMING OF 120 SECONDS CONFORMING TO IRS-S-61-2000 WITH AMENDMENT NO.1 IRS-S-34 AND IRS:23 (AS APPLICABLE) OR LATEST. THE INTERLOCKING SHALL BE AFGKY

Red Aspect LED signal Lamp for main colour light signal, retrofitable in existing CLS housing with integrated CRU and compatible with AC LED ECR as per RDSO spec. No. RDSO/SPN/199/2010 Revision: 1.0 latest

Yellow Aspect LED signal Lamp for main colour light signal, retrofitable in existing CLS housing with integrated CRU and compatible with AC LED ECR as per RDSO spec. No. RDSO/SPN/199/2010 Revision: 1.0 lates

Green Aspect LED signal Lamp for main colour light signal, retrofitable in existing CLS housing with integrated CRU and compatible with AC LED ECR as per RDSO spec. No. RDSO/SPN/199/2010 Revision: 1.0 latest

Calling on LED Signal Lighting Unit 110 Volts with Built in current Regulator for Railway signalling Retrofittable in Existing CLS housing and Compatible with AC LED ECR as per RDSO Spec.No RDSO/SPN/153/2011 Rev.4.1 or Latest amendment

LED shunt signal lighting unit, 110V AC retrofittable in existing CLS housing and compatible with AC LED ECR as per RDSO Spec.No.RDSO/SPN/153/2011 Revision 4.1

ROUTE LED SIGNAL LIGHTING UNIT, 110V AC , RETROFITTABLE IN EXISTING CLS HOUSING AND COMPATIBLE WITH AC LED ECR , AS PER RDSO SPECN. NO. RDSO/SPN/153/2011(REV.4.1.) OR LATEST WITH AMENDMENT UP TO DATE IF ANY.

Supply of FUSE Links of (400mA, 630mA, 1A, 1.6A,2A, 4A, 6.3A & 10A)

Supply of special type location box- full size (RVNL drg no. RVNL/S&T/SG-10/2005) from RVNL schedule further modified in order to accommodate IPS goomty module in outdoor full size location box)

Fabrication & supply of MS Termination box of size 18"x9"x5" for Point machine. The termination box to be fabricated with 2Nos., of MS angles 50x50x6 mm each of one meter length and Gl 43 pipe 18". The termination box is also to be provided with teak wood plank of approximate size of 16"x7" and 25mm thick for fixing of terminals. Necessary bolts, nuts and screws are to be provided for the fabrication of termination box. The termination box is to be painted double-coat with approved quality of paint black/silver enamel on the outside and to be painted with white enamel paint inside of the box (All the materials to be procured by the contractor

Color LCD Thermal imager as per RDSO Specn.No. TI/PSC/OHE/TIPS/10321 (12/2013) REV-2 or latest if any accessories, Model: FLUKE- PTI120 and equivalent model in TESTO, Fluke, FLIR make.

Supply of Block Filter Unit (Block Instrument) in 25 KV AC in RE Area as per RDSO spec no. IRS:S-68/89 or latest and block bell equipment as per RDSO spec no. IRS:TC-44/88 or latest.

Supply of SPD Life tester,designed for on-site testing of surge protective devices(SPD). It allows checking and indicating the health status of GDT/MOV based SPD of voltage range upto 1000V. It shall indicate the status of SPD by measuring its electrical parameters.

Supply of DC-DC converter Module DC-DC 24-40V ,10 A to suit existing IPS of Statcon Make as per latest RDSOspecification RDSO/SPN/165/2012ver.3.0 or latest . Inspection by RDSO. Material shall be procured from RDSO approved firms

Supply of insulated ESM Tool kits to suit RE standards,Standard Tool Bag (CANAVAS)-1No., Soldering Iron (Make "Soldem/Philips)- 1 No., Multi meter (Digital PHILIPS/FLUKE/185)-1 No., TRUE RMS METER Rishi B 18S or Rishi 6015 or Similar) up to 20M.ohms 10A, 5KHZ, 2mV to 750V AC, 200V DC-1No.; Screw driver set of 6 pieces(Taparia Make)-1 No., Cutting pliers 6"(Taparia)-1No., Side Cutter (wire cutter 6" (Teperia) Nose plier 6"(Taparia)-1no., Wire stripper(Taparia)-1no., Fiber tape 3 meters-1 No., Scale 6" (for 48 tongue rail opening)(S. S. material)-1no., Pop spanner wrench 8mm to 22mm (auto adjustable spanner) Taparia Make.-1no, Pop spanner wrench 10mm to 30mm (auto adjustable spanner)Taparia Make-1no, Pop spanner wrench 15mm to 41mm (auto adjustable spanner) Taparia Make-1 no, Hacksaw frame with blade 6" 4" width 1 No, (for cutting cable)-1No, Hammer 3.0 lbs-1no, Chisel 6" (for cutting bond wire)-1no, Poker 8 (for removing bond wire bond pin)-1No., Screw driver Heavy duty 12" with plastic Handle (for opening of detector contact (Taparia)-1no, Test piece (Pt wedge piece) 2 Nos., Universal key -7nos, Box spanner for 8- way terminals (13mm) (for opening ARA terminals)-1no, Insulated Spanner for point lock rod adjustment of size 36mm -1No., Insulated Spanner for point throw rod adjustment of size 50mm-1No

C1-(Non-SOR execution items)

Laying of HDPE Duct in already made trench and through DWC/GI/RCC pipes where ever necessary and duct integrity testing.

Blowing of OFC through HDPE/DWC duct using blowing machine and other associated works and as directed by Railway Engineer.

Excavation of jointing pit and provision of joint chamber of 1.2 M dia of 60 cm height with 2 3 piece cover on top and bottom cover with holes for drainage ( reinforcement drawing will be as per technical spec). This includes water cooling of chamber, backfilling and ramming of the trench after cable laying and consolidation of soil as well as disposal of soil as per plan as advised by site engineer

Providing dry sand in FRP/RCC joint chambers up to 400mm height

Provision of derivation joint for emergency contract using thermo shrinkable joint kit confirming to No:IRS-TC-77/2006 ( or latest)using miniature tappping transformer of 470:1120 ohms impedance confirming to RDSO specification No;IRS-TC 77/2006 (or latest). One pair for auto phone should be taken out separately and terminated in th EMC box. After jointing the cable through test such as 5 insulation and conduction tests etc should be carried out jointly with Rilway representative at site.If any defects or damages are observed during jointing the contractor should re do the joint free if cost.Thermo shrinkable jointing kit confirmint to RDSO specNo.IRS TC 77/2006 (or latest) of suitable size for straight cum derivation joint to suit 6 quad main cable and 10 pair PIJF cabl, 2T(1Quad) 470:1120 transformer joint asembly with phantomtapping and all othyer miscellaneous materials required for the work shalll be supplied by the contractor)

Localization and restoration of low insulation/break fault. This work involves excavation of 6 existing joint location replacement with new normal/derivation joint. (Jointing kit will be supplied by railways) at isolated locations where above item is not applicable. This item includes excavation and closing of jointing pit of size 1.5 x1.5 x1.0 mtr

Rectification and re-splicing of existing mid section OFC joints. This includes supply and provision of joint kit & sleeves

Replacement of Emengency socket six pin suitable plug as per RDSO spec. No.IRS/TC/42/87 Amd.1 or latest.

Replacement of emergency socket box to RDSO Drg No. 15220 with socket six pin flat of RDSO spec No.IRS/TC/42/87 Amd.1 or latest.

Wiring alteration, configuration & validation of existing datalogger for all new contacts in connection with alteration work. this includes additional cards required in dataloggers and indoor signalling cable for wiring in relay room from existing relay rack to datalogger(unit:1Number=station/LC)

Alteration to database, faults, simulations in dataloggers & all connected places (like HQ, FEP, Station, etc)

Releasing of existing Axle counter system with TX /RX coils

Video recording of cable trench using minimum720P and above HD camera and submit one copy in New removable hard disks (With capacity as per requirement)

Physical tracing and opening/locating of existing working cables by precession digging for diversion of cables in connection with cable clearance for engineering earth work without interfering the circuits as per the advice of Railway site engineer.

Fixing of Calling-on Signal/A-Sign/AG-Sign unit on signal post. The item includes fixing of Co- 15 On signal /'A' sign/ 'AG' sign unit on signal post with bracket, hood etc. Item includes supply bracket & fixing materials etc. by the contactor. The item also includes termination of cables & wiring inside Co- On signal /'A' sign/ 'AG' sign unit as per standard practice.

Fixing of KLCR relays in field in half location boxes. Item includes supply and fixing of MS sheet and wiring of push buttons and LEDs for KLCR circuit. The KLCR relays, push buttons, LEDs to be fixed 16 on a MS sheet of min.3mm in the half location box. The MS sheet should cover the full length and breadth of the half location box and can be in two pieces of approx. 48cm x 46cm and 80cm x 46cm. The first piece to be fitted on top and will contain the KLCR relays, LEDs and push buttons. The second piece to be fitted below the first piece to divide the two halves of the location box. (Supply of KLCR relays not covered in this Schedule).

Arrangement for commissioning of station for the work of Non-Interlocking period at site such asprovision of 2 Tent, 4 Table, Chair(8no in each Tent) in general, Drinkingwater & other amenity, Cap, 17 UmbrellaTorch for 30 staffs, Hand Gloves forSix to Eight staff, and arrangement foone vehicle at each station for thework of NI period for required commissioning of station for the work of Non-Interlocking period at site,Lighting arrangements in tent, in the yard over point zone for properworking in the evening and night as required. If necessary , DG has to bearranged by the contractor on his owncost including diesel, lubricant oil etc,. Necessary arrangement should bedone as advised by Site Engineer.

Cutting of the platform surface(Tile/Slab) for a depth of 25cm and awidth of 10cms and 18 refilling/Reconditioning/ Concerting/ Repairingthe platform after laying HDPE pipe andcable. Cutting should be done withmarble cutting machine in propermanner and restore the same as beforein such a manner that aesthetic of theplatform is not disturbed.

Horizontal direction drilling/boringwithout damage of surface road/track using Auger Machine(HDDmachine). The bore shall be upto200 mm dia & shall be done at thedepth of minimum 1200 mm fromthe ground level. The ground levelshall be considered ignoring thebank height of the bank of the 19 road.The length of the bore shall beminimum 4 Mtrs long. This includeinsertion of different dia DWC- HDPEpipe/ GI pipes coupling etc. as perdirection of Engineer In charge.Note:- Pipe Supply is not coveredunder this item. Contactor shallprovide all material required forboring and adequate nos. of laboursfor proper laying of cables into thebore. Cable shall be laid cautiouslyso that it should not get damagedue to rough handling & pressureon cable.

Shifting/ re-installation,testing & Commissioning of SLIDING BOOM complete along with E 20 Type locks on sliding boom post and gumty.It includes testing & commissioning of ground leverframes (if any), E type locks and CB on GFas perapproved SIP. The item includescasting/shifting of foundations required for installation of sliding booms of both side with contractor's own material and supply of other nut-bolts,rivets, limit switches etc required for commissioning of sliding boom.

Preparation of Station Working Rules (SWR) in English on the basis of station working rule 21 diagram/gate working rule diagram to be supplied by the contractor. Submission of two draft copy to railway for checking and resubmission of draft in three copies for approval of division after making corrections.Soft copy (Editable form) to be supplied in pen drive.

Preparation of Station Working Rules (SWR) in Hindi/Regional Language of that station. Procedure to be followed as per above item i.e for preparation for SWR in english.

Excavation of cable trench as per cable route plan, 1.2 Mtr. deep and of 0.3 Mtr. to 0.6 Mtr. wide at bottom without brick as per DRG. NO. S&T/C-40(NKG), SK/4/95/NKG, SK/8/95/NKG. or latest alongside the track in all kinds of soil, conforming to distances as per cable route plan and refilling. This work includes clearing of route from bushes etc. The work shall be done as per the extant practice on Eastern Railway and instructions of Railway Engineer at site. Note:-(a) for all trenches from distant signal to home signal and to relay room, the minimum headway above the uppermost cable in the trench should be 600mm. If due to a large no. Of cables headway is not available, 4" of 1:2:4 concreting should be done. Note:-(b-1) payment will be made as per actual work done on pro-rata basis, if required depth is not available at site. (b-2) if the depth of trench is not uniform in a span of 100 mtr. Or shorter lengths if site condition demands along the cable run, minimum depth will be taken for that particular stretch for payment.

Excavation of cable trench as per cable route plan, 1 Mtr. deep and of 0.3 Mtr. to 0.6 Mtr. wide at bottom as per RDSO sketch No. SDO/CABLE LAYING/003 or latest alongside the track in hard soil, conforming to distances as per cable route plan and refilling. This work includes clearing of route from bushes etc., covering of cable laid in trench by loose soil for a layer of 50mm thickness approximately 24 before covering by bricks. The work shall be done as per the extant practice on Eastern Railway and instructions of Railway Engineer at site. Note:-(a) for all trenches from distant signal to home signal and to relay room, the minimum headway above the uppermost cable in the trench should be 600mm. If due to a large no. of cables headway is not available, 4" of 1:2:4 concreting should be done. Note:-(b-1) payment will be made as per actual work done on pro-rata basis, if required depth is not available at site. (b-2) if the depth of trench is not uniform in a span of 100 mtr. Or shorter lengths if site condition demands along the cable run, minimum depth will be taken for that particular stretch for payment.

D1-Non SOR Supply and installation items)

Supply and installation of OFC Joint closure conforming toTEC Spec. and splicing of Optic Fibre Cable' (48 Fibres) and testing of fibre for 1310 :1550 nm.

Supply and Installation of Rack mountable 48 Fibre management system (FMS) conforming 2 to RDSO/SPN/TC-3712000(rev-3) amdt-1 or latest similar to COMSCOPE make or better, suitable forsplicing and front patching 48F cable with all accessoriesand terminating the optical fibre cable with splicing andfront patching in FMS in the equipment room . (OFC Pigtail patch chords ofsuitable length and all other materials required for splicing are to be supplied by contractor)

Fabrication supply and fixing of P,C,A,G etc retro reflective marker disk on signals conforming to RDSO Drg.No.SA-23456 as per standard practice with contractors complete material including fixing of clamp.

f} Painting of MS Flat with one coating of red oxide as primary and two coats of anti- corrosive black.

Supply, design, installation, testing and commissioning of Multi section Digital Axle counter (MSDAC) complete system as per RDSO specification no.RDSO/SPN/176/2013 version .3 or latest configuration . MSDAC should have facility to reset track sections. Syatem shall be with co-operative type design. Design of axle counter circuit, indoor installation, testing and commissioning of MSDAC (per unit), supply of essential 10% spares covering all types of cards, wheel sensors for MSDAC detaile cost and quantity wise break up of all spares should be given. Supply of diagnostic system from remote diagnostics (per 1 no.) tool set for wheel sensor mounting maintenance of MSDAC consisting of torque wrench, ratchet, testing plate, measuring tape, srew driver and gloves and multimeter Fluke 115 (1 No.) Note: Detailed specification and drawing as per annexure. (Unit Numbers = Per DP)

Supply and Laying of PVC Warning Tape colour Orange, width of 250mm (10") by printing with blackletters 'Indian Railway Signal/Telecom/OFC Cable' on both sides of the tape

FA-(Non-SOR Fire alarm items)

Supply of Elide Fire Automatic Fire Ball for Fire Extinguishing of Medium size - the weight of the agent is not less than 1.0 kg but less than 1.8 kg Elide Fire (Fire Ball)

Item Breakup - A-SOR-2011 items

100.00 Passenger Platform, trenching to a depth of 0.6m to accommodate the additional cables, replacing the slabs removed after the cables are laid and replastering with cement mortar, refilling the trench by ramming and consolidating it as per the instructions of Railway Representatives at site. (Laying of cables is not included in this schedule). [Cement, river sand and all other miscellaneous materials required for the work shall be supplied by the Contractor].

240.00 crossing of cables, laying of DWC/ RCC pipes with collar/coupling, refilling of trench by ramming and consolidating it as per the instructions of Railway representative at site. During excavation of trench it has to be ensured that the excavated soil does not mix with the ballast available. The depth of 1m trench shall be from the bottom of sleepers for track crossings. Laying of cables is not included in this schedule. (Supply of DWC/RCC pipes with couplers/ collars is not included in this schedule)

30.00 crossing of cables, laying of DWC/ RCC pipes with collar/ coupling, refilling of trench by ramming and consolidating it and resurfacing it to the original position. Laying of cables is not included in this schedule. (Supply of DWC/RCC pipes with couplers/ collars is not included in this schedule).

120.00 laying with offset at both ends and with couplings over RCC Bridges/ Drainage/ Culverts with concrete masonry supports of size 300mm x 300 mm x 300 mm at an interval of 2m. The ends of the pipes shall be closed with brick masonry abutments work so that no cable is exposed, The work shall be carried out as per the instructions of Railway representative at site. (Supply of GI pipes with couplings and laying of cables is not included in this schedule). [Stone jelly of size 20/25mm, bricks, sand, cement and all other miscellaneous materials required for the work shall be supplied by the Contractor]. BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY

120.00 laying in hard rocky area with off sets at both ends duly supported by concrete blocks of size 300mm x 300 mm x 300 mm at an interval of 2m. The ends of the pipes shall be closed with brick masonry abutments work so that no cable is exposed, The work shall be carried out as per the instructions of Railway representative at site. (Supply of GI pipes with couplings and laying of cables is not included in this schedule). [Stone jelly of size 20/25mm, bricks, sand, cement and all other miscellaneous materials required for the work shall be supplied by the Contractor].

of cables as per cable plan in cable trenches, masonry ducts, RCC Pipes, DWC pipes, GI Pipes etc. (Supply of cables is not included in this schedule).

1000.00 approximately 220mm x 100mm x 60mm breadth wise horizontally above the cables in 0.3m width trench. [Country bricks of size 220mm x 100mm x 60 mm (approximately) shall be supplied by the Contractor].

140.00 No.CSTE/CN/OFC/1. The lettering on the cable marker shall be "SIG" / "TELE" / "OFC" as per the instructions of Railway representative at site.

140.00 300mmX300mm, casting of concrete foundation of size 300mmX300mmX300mm and Placing of RCC cable markers on top of the foundation and refilling the pit and consolidating it by ramming. The cable markers shall be provided at an interval of 20 Mtrs. within station limits and 50 Mtrs. outside station limits throughout the cable route, diversions and also at every track/road crossing.

30.00 and depth as instructed by Railway representative at site, for coiling the cables in rear of relay rooms/ AFTC huts, apparatus cases etc. The work includes coiling the underground cables, and placing closely one layer of country bricks of size approx. 220mm x 100mm x 60mm breadth wise above the cables to cover all the cables in the cable pit, closing and consolidating the pit by ramming and leveling. [Country bricks of size 220mmx100mmx60mm (approximately) shall be supplied by the Contractor].

240.00 103.5mm inner dia & 120mm outer dia conforming to specification No. IS 14930(Part 2): 2001 with one coupler for every 6m of pipe as specified in Vol.II of the Tender document.

120.00 specified in Vol.II of the Tender document

20.00 erection of apparatus case full size as per Drg. No.SG/CN/02/6 and fixing of 2 Nos. of 'E' type locks, one for the front door and another for the back door, fixing of one hard wood shelf plank 37mm thick and painting the apparatus case inside and outside with one coat of red-oxide and two coats of aluminium paints. (Supply of apparatus case is not included in this schedule). [Foundation bolts & nuts, 'E' type locks, cement, river sand, stone jelly of size 20/25 mm, hardwood plank of 37mm thick, paints, varnish, fixing bolts & nuts and all other miscellaneous materials required for the work shall be supplied by the Contractor.] BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY

10.00 erection of apparatus case half size as per Drg, No.SG/CN/02/7, fixing one 'E' type lock for the front door and latching arrangement for the back door, and fixing of one hardwood shelf plank 37mm thick and painting the apparatus case inside and outside with one coat of red-oxide and two coats of aluminium paints. (Supply of apparatus case is not included in this schedule). [Foundation bolts and nuts, cement, 'E' type locks, river sand, stone jelly of size 20/25mm, 37mm hard wood planks, latching arrangements, paints, varnish, fixing bolts & nuts and all other miscellaneous materials required for the work shall be supplied by the Contractor]

12.00 boxes on rails and concreting as per Drg. No.SG/CN/02/8, drilling of suitable holes in the box, fixing of 2 Nos. of GI pipes 32mm dia and 300mm long at the bottom with clamp nuts - 12 mm thick, one at the inner side and another at the outer side for each pipe for cable entry and one GI pipe 150mm long 32mm dia for drawal of jumper wires for Point machines etc., fixing of hardwood plank 37mm thick on the bottom, provision of one EWS lock, and painting the boxes inside and outside with one coat of red-oxide and two coats of aluminium paints. (Supply of CT boxes is not covered in this schedule. Rails of different length shall be supplied by Railways. The contractor shall cut lengthy rails wherever required.) [Cement, river sand, stone jelly of size 20/25mm, paint, varnish , GI Pipes 32mm dia - 300mm long - 2 Nos and 150mm long - 1 No., clamp nuts - 12mm thick - 2 Nos. for each pipe, fixing bolts and nuts with washers, EWS locks, paints and all other miscellaneous materials shall be supplied by the Contractor]. Excavation of pit in and around the existing location boxes very carefully without damaging the working cables and shifting and turning the location boxes to clear of the infringement as instructed by the Railway representative at site. The work includes ensuring the safety of the signaling system, releasing the cable coils to give access for shifting/turning the location boxes. Necessary masonry work and earth work in and around the location boxes to the required level shall be done as instructed by the Railway representative at site. If the existing earth connections to the location boxes are disturbed, the earth wires shall be properly re-connected. [All materials required for the work shall be supplied by the Contractor].

1000.00 terminals/ fuse blocks in apparatus cases/ battery boxes/ CT boxes/ cable termination racks as per approved circuit diagram. The terminal particulars are to be repainted /corrected on the doors of apparatus cases/ battery boxes/ cable termination boxes and FTOT index board as instructed by Railway representative at site. This work includes closing the opening created for entry of new cables in the apparatus cases with masonry brick work and sealing the bottom of the apparatus cases/ cable termination racks with cable compound. [Paints, wire PVC 3/0.75mm and 16/0.2mm copper, sealing compound, bricks, cement, river sand and all other required miscellaneous materials shall be supplied by the contractor]. {Unit: Per Terminal Block} BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY Termination of main, tail, Signaling and power cables and internal wiring on terminal/ fuse blocks in new apparatus cases, cable termination boxes and in gate Lodges excluding cable termination rack at relay room. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, fixing of Phynolic synthetic industrial fibre base fine weave cotton fibre board 6mm thick for terminal board to suit each apparatus case, varnishing all teakwood items, fixing of terminals/ fuse blocks on the terminal board, drilling of necessary holes, termination of cables, wiring, identification of cables using aluminium tags with letters punched neatly, as per approved circuit diagram and cable plan, painting of particulars on sleeves and also on the inner side of the doors of apparatus cases. After terminations are over, the side openings of apparatus case foundation shall be closed with brick work, cement plastered, the inter-space filled with river sand up to base level and the bottom surface shall be sealed with sealing compound. (Supply of PBT terminals and Fuse blocks is not covered in this schedule). [Cement, teakwood cable clamp 50mm x 50mm, base planks 100mm x 25mm, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, PVC/Nylon sleeves, varnish, paints, bolts, nuts and washers, Nondeteriorating type of fuses of various capacities, Aluminium cable tags, sealing compound, country bricks 220mm x 100mm x 60mm, copper bus bars, brass screw, river sand, wire PVC3/0.75mm copper and other miscellaneous materials shall be supplied by the Contractor].

2000.00 location)(Phynolic sheet) {Unit: Per Terminal Block}

140.00 (Phynolic sheet) {Unit: Per Fuse Block} Termination of main, tail, Signaling and power cables and internal wiring by fixing additional terminals/ fuse blocks on the existing terminal boards of apparatus cases, cable termination boxes etc. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, varnishing all teakwood items, fixing of terminals/ fuse blocks, on the existing terminal boards, drilling of necessary holes, termination of cables, wiring, identification of cables using aluminium tags with letters punched neatly, as per approved circuit diagram and cable plan, painting of particulars on sleeves and also on the inner side of the doors of apparatus cases. After terminations are over, the side openings of apparatus case foundation shall be closed with brick work, cement plastered, the inter-space filled with river sand up to base level and the bottom surface shall be sealed with sealing compound. (Supply of PBT terminals and Fuse blocks is not covered in this schedule). [Cement, teakwood cable clamp 50mm x 50mm, base planks 100mm x 25mm, PVC/Nylon sleeves, varnish, paints, bolts, nuts and washers, Non-deteriorating type of fuses of various capacities, Aluminium cable tags, sealing compound, country bricks 220mm x 100mm x 60mm, copper bus bars, brass screw, river sand, wire PVC3/0.75mm copper and other miscellaneous materials shall be supplied by the Contractor].

400.00 (existing location) {Unit: Per Terminal Block}

40.00 location) {Unit: Per Fuse Block} BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY Manufacture and supply of M.S. relay frames of suitable size to hold up to 4/ 8/ 12/ 20 relays /plug in type HMU as required by Railways and fixing them in apparatus cases for all types of signal control circuits, LC gate control circuit and Point control circuits, fixing of plug boards, relays, resistors and electrolytic condensers on Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, wiring and termination as per approved circuit diagram and painting the particulars. (Supply of all types of relays, plug boards, connectors, retaining clips and plug in type HMU is not covered in this schedule). [Wire PVC copper, 3/0.75mm and 16/0.2mm copper, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, for fixing resistors and condensers, MS flats 25mm x 6mm brass bolts and nuts, paints, soldering materials, resistors, condensers and all other miscellaneous materials required for the work shall be supplied by the contractor].

8.00 relays/Plug in type HMU)

4.00 relays/plug in type HMU)

2.00 relays/plug in type HMU)

14.00 per Drg.No.SG/CN/02/9 using metallic templates, for erection of colour light signals up to 4 aspects. [Foundation bolts, cement, river sand, stone jelly of size 20/25mm dia and all other miscellaneous materials required for the work shall be supplied by the Contractor].

14.00 colour light signal up to 4 aspects complete on Signal pole/ Off-set bracket, (for LED/ filament bulbs) with lenses, triple pole lamp holder, filament switching units, CLS transformer, current regulators (whichever is applicable), fixing of ladder with platform complete and concreting of ladder shoe, fixing of number plates, marker board, lens guard, fixing of speed limit board wherever necessary, termination of tail cables, wiring of signal unit with PVC wire 3/0.75mm copper, provision of EWS locks, and painting of one coat of red oxide and two coats of aluminium/ enamel paints. When the aspect is fixed on Offset bracket using 'U' bolts and nuts, a through bolt shall be provided by drilling a hole in the signal pole to prevent the offset bracket from sliding down. (Supply of surface base, Offset bracket, CLS pole, CLS aspects complete, ladder with shoes and platform, Speed limit board, LED aspects, current regulators, lamp holders, lamps, filament switching unit and CLS transformer is not covered in this schedule). ['U' bolts and nuts, through bolts and nuts, cement, stone jelly 20/25mm dia, river sand, Signal Collar Rings, wire PVC 3/0.75mm copper, lens-guard, all fixing bolts and nuts, lead wool, paints PVC/Nylon sleeves, enameled number plates. enameled marker boards, EWS locks, and all other miscellaneous materials for the work shall be supplied by the Contractor].

4.00 as per Drg, No.SG/CN/02/10 using metallic templates, for erection of ground type colour light shunt signal. [Foundation bolts and nuts, cement, river sand, stone jelly of size 20/25mm and all other miscellaneous materials for the work shall be supplied by the Contractor]. BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY

4.00 including surface base, signal pole, LED aspects/ lenses, bulbs with holders (whichever is applicable), fixing of lens guards, number plate, termination of tail cables, wiring of signal unit with PVC wire 3/0.75mm copper, provision of EWS locks and painting of one coat of red oxide and two coats of Aluminium/ enamel paint. (Supply of Ground type shunt signal complete including surface base, signal pole, LED aspects, holder, bulbs, and lenses is not covered in this schedule). [Wire PVC 3/0.75mm copper, lens guards, EWS locks, Enameled number plates, bolts and nuts, lead wool, paints and all other miscellaneous materials shall be supplied by the Contractor].

8.00 erection of Post type shunt Signals, termination of tail cables and wiring using wire PVC 3/0.75mm copper, provision of EWS lock and painting of one coat of redoxide and two coats of aluminium/ enameled paint. The work also includes drilling suitable holes on the CLS post and provision of a through bolt with nut to prevent the Off-set bracket from slipping down. (Supply of Post type Shunt Signals, LED aspects and Off set brackets is not covered in this schedule). ['U' bolts and nuts, through bolts with nut, wire PVC 3/0.75mm copper, EWS lock, Enameled number plates, wire mesh, PVC/Nylon sleeves, paints and all other miscellaneous materials shall be supplied by the contractor]. Fixing of junction type route indicators - 1 way to 6 ways - complete/ fixing of additional limb to the existing route indicators, termination of tail cables, wiring as per approved circuits diagram using wire PVC 3/0.75mm copper, provision of required No of EWS locks, wire mesh, and painting. (Supply of junction type Route Indicators - complete and additional limb is not covered in this schedule). [3/0.75mm wire PVC, fixing bolts and nuts, EWS locks, wire mesh, PVC/Nylon sleeves, paints and all other miscellaneous materials shall be supplied by the Contractor].

2.00 route indicator

8.00 erection of Calling On Signals/ 'A' marker lights, termination of tail cables and wiring using wire PVC 3/0.75mm copper, provision of EWS lock, number plates/ marker boards and painting. The work also includes drilling suitable holes on the CLS post and provision of a through bolt with nut to prevent the Offset bracket from slipping down. (Supply of Calling On Signal/ 'A' marker light, LED aspects/holders & bulbs and Off set brackets is not covered in this schedule). ['U' bolts and nuts, through bolts with nut, wire PVC 3/0.75mm copper, EWS lock, Enameled number plates, wire mesh, PVC/Nylon sleeves, paints and all other miscellaneous materials shall be supplied by the contractor]. BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY

2.00 very carefully without causing damage to the working cables and shifting the Signals along with the concrete foundations for approximately 1m to a nearby position so as to clear the infringement from the nearest track centre as instructed by Railway representative at site. The existing cable coils shall be released carefully so as to give access for shifting. Necessary masonry work and earth work shall be carried out in and around the signals after shifting as instructed by Railway representative at site. [All materials required for the work shall be supplied by the Contractor].

10.00 plates as per drawing No.TY/08/2008 with fixing arrangements and fixing them on the existing Signals as per the instructions of Railway representative at site. [Enameled number plates with fixing arrangements with bolts and nuts shall be supplied by the Contractor].

6.00 Signals in RE area as per standard practice. The work comprises of providing MS angle frame and wire mesh in order to avoid close proximity of OHE wires. The work also includes provision of earthing wire using 4 SWG GI wires from the screening arrangement up to surface base as per the instructions of Railway representative at site. [All materials required for this work shall be supplied by the Contractor]. Provision of DC Single/ Double rail track circuit to suit RE/ Non-RE areas as per approved signaling plan using Plug-in type track relays. This work includes provision of double bonding, and parallel jumpers, provision of bond wire clips, provision of track lead connections using 2c X 2.5 sq.mm cable, provision of TLD boxes 2 Nos. at Relay end, 2 Nos. at Feed end and 2 Nos for parallel jumpers as necessary to suit layouts, for each Track Circuit, and termination of jumpers and tail cables in track lead junction boxes, installation of relays, track feed battery chargers to charge up to 4 cells, track feed resistance, B type choke and secondary cells - 80 AH capacity in apparatus cases and wiring with wire PVC 3/0.75mm copper. The work also includes painting of track Circuit No. with Feed end/ Relay end details on the TLD boxes. The work also includes provision of insulations for gauge tie plates and nose crossing plates wherever required. (Provision of rail joint insulation is not covered in this schedule.) (Uninsulated gauge type plate and nose crossing plate will be supplied by Railways. Supply of track feed battery charger, B type choke, track relays, uncharged secondary cells (2V - 80AH), TLD boxes with stumps, 2cX2.5 sq.mm cable, is not covered in this schedule). [track feed resistance, Gauge tie plate and nose crossing plate insulations, PVC/Nylon bushes for TLD boxes, PVC sleeves, all types of fixing bolts and nuts with spring and flat washers, teakwood stand for fixing track feed resistance, GI bond wire 8 SWG, Channel bond pins, bond wire clips, paints and all other miscellaneous materials shall be supplied by the contractor. Secondary cells-80 AH capacity shall be charged by the contractor through reputed charging agencies].

Numbers BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY Alteration to existing DC Track Circuits to suit RE/Non RE standard as per approved signalling plan. This work includes provision of double bonding and parallel jumpers, provision of bond wire clips, wherever required, shifting of relay end and feed end equipments and re-wiring them, provision of track lead connections wherever necessary using 2c x 2.5 sq.mm cable, provision of TLD boxes and termination of jumpers and tail cables in track lead junction boxes, shifting of Track feed/Track relay set wherever required and wiring with PVC 3/0.75mm copper wire. (Supply of TLD boxes, 2c x 2.5 sq.mm cable and TLD boxes with stumps is not covered in the schedule. Existing Track relays, Track Feed Resistance, Track feed battery chargers, B type Chokes and Charged secondary Cells shall used for this work). [Wire PVC 3/0.75mm, PVC/ Nylon bushes for TLD boxes, PVC sleeves, all types of bolts and nuts with spring and flat washers, teakwood stand for fixing track feed resistance, GI bond wire 8 SWG, Channel bond pins, bond wire clips, paints and all other miscellaneous materials shall be supplied by the Contractor].

48.00 No.SG/SN/02/13 and earthing of metallic sheath and armour of all cables in all apparatus cases, relay room, equipment room, ASM room for block and control, and earthing of all equipments in apparatus cases, power room, relay rack, cable termination rack, control panel, signals, lever frames with MS flat 35mm X 6mm/19c cable (MS flat for closer by areas and MS flat/19c cable combination for farther areas) as per the instructions of Railway representative at site. The work includes painting of earth resistance value on the earth pit. (Supply of 19C cable is not covered in the scope of this schedule). [MS flat for earthing 35mm X 6mm, cement, GI earth electrodes, common salt, charcoal, country bricks, river sand, soldering materials and all other miscellaneous materials required for the work shall be supplied by the Contractor].

12.00 type and connecting all ground connections including wiring and termination in point machine and interconnections between point machine and CT box through PVC hose pipe with 3/0.75mm and 7/1.40mm copper wire and painting. This work includes provision of insulation to stretcher bars, throw bar lug and "D" bracket wherever required, cutting of notches on the point machines covers to suit crank handle configuration. (Combined type point machine with ground connection, uninsulated stretcher bar, throw bar lug and 'D' brackets will be supplied by Railways. [All types of insulations connected to point work, coal bengal, all type of bolts and nuts, washers spring/flat wire PVC 7/1.4mm copper, PVC hope pipe, paints, PVC/nylon sleeves and all other miscellaneous materials required for the work shall be supplied by the Contractor]. Supply of Colour light Signal pole 140mm dia, 4.6m/ 3.6m tall with necessary inspection as per specification/ drawing/ description enclosed in this document.

14.00 140mm dia with necessary inspection as per specification/ drawing/ description enclosed in this document. BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY Supply of ladder with platform and shoes to suit CLS pole 4.6m/ 3.6m tall, with necessary inspection as per specification/ drawing/ description enclosed in this document.

10.00 hood etc., with necessary inspection as per specification/ drawing/ description enclosed in this document.

8.00 surface base, signal pole, hood etc., with necessary inspection as per specification/ drawing/ description enclosed in this document. Supply of Colour Light Signal Multi Unit type - complete for 4/ 3/ 2 aspect with mounting socket, with necessary inspection as per specification/ drawing/ description enclosed in this document.

Numbers Supply of Junction type route indicator - 5 unit arm - 1/ 2/ 3/ 4/ 5/ 6 way with mounting sockets, with necessary inspection as per specification/ drawing/ description enclosed in this document.

Numbers Supply of Calling On Signal / 'A' marker light - complete with necessary inspection as per specification/ drawing/ description enclosed in this document.

Numbers Supply of Off-set brackets - large/ small made of cast iron with necessary inspection as per specification/ drawing/ description enclosed in this document.

150.00 terminals and stumps with necessary inspection as per specification/ drawing/ description enclosed in this document. Supply of PBT terminals 25mm/ 60mm centre and PBT Fuse blocks with necessary inspection as per specification/ drawing/ description enclosed in this document.

Numbers Supply of Low maintenance secondary cells of the following capacities with necessary inspection as per specification/ drawing/ description enclosed in this document.

Numbers Supply of apparatus cases (full/ half/ quarter size) to suit Southern Railway standard with necessary inspection as per specification/ drawing/ description enclosed in this document:

4.00 required ward Nos. with keys, with necessary inspection as per specification/ drawing/ description enclosed in this document. BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY

24.00 description enclosed in this document. Fixing of PBT terminal block/ PBT fuse block, rubber grommets, clamping of cables using teakwood cable clamps and base planks, termination of cables, provision of ND type fuses of required capacities, provision of copper bus bar for supply terminals, wiring, provision of termination particulars diagram board using plywood of thickness 12mm - teakwood finish of size 1800mm x 1200mm with Aluminium grooved channel frame in the relay room. The blank spaces over the top of the cable termination rack shall be covered with phynolic sheet of thickness 3mm wherever required. The termination and cable core particulars shall be painted on the PVC/ nylon sleeves. The work also includes identification of cables using aluminium tags provided on each cable with letters punched neatly. (Supply of PBT terminal blocks 25mm & 60mm centers and PBT Fuse blocks is not covered in the schedule) [Wire PVC 3/0.75mm copper, brass bolts and nuts and washers, for fixing PBT terminal/Fuse Block, other fixing bolts and nuts, rubber grommets, PVC/ Nylon sleeves, copper bus bars, teakwood 50mm x 50mm for cable clamps, 25mmx 100mm for base planks, phynolic sheet 6mm thick of size 1200mm x 1800mm with aluminium grooved channel frame, phynolic sheet 3mm thick, paint and all other miscellaneous materials shall be supplied by the Contractor].

800.00 and termination {Unit: Per Terminal Block}

10.00 termination {Unit: Per Fuse Block}

40.00 relay racks/apparatus cases as per the approved circuit diagram using wire PVC 16/0.2mm copper. The work includes painting alterations and releasing the unwanted wires carefully without disturbing the existing wiring. [Wire PVC 16/0.2mm copper, soldering materials, bunching threads, condensers, resistances and teakwood plank for fixing them and all other miscellaneous materials required for the work shall be supplied by the Contractor].

2.00 station equipment complete as per RDSO specification No.IRS.TC@45<47@93 and 4 wire control telephone with audio visual indication and reset button fitted on telephone conforming to specification No.IRS-TC@45&47@97 or latest. This work also includes supply and wiring of power supply arrangements for way station equipment conforming to specification IRS.TC.72/97. or latest [All the materials required for the work shall be supplied by the Contractor].

10.00 6mm thick and with an insulation to withstand Foot 650VAC, on the floor of relay room etc at places as indicated by railway representative at site. BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY

2.00 handle or on suitable fixtures at station/apparatus case, provision of economiser push switch with locking facility, wiring with wire PVC 16/0.2mm copper, provision of teakwood terminal box covered with decolum along with locking facility and painting. (Supply of electric key transmitter and crank handles is not covered in this schedule). [wire PVC 16/0.2mm copper, wire wound resistance, decolum covered terminal box with locking facility by using 25mm thick teakwood, bolts and nuts, paints, push switches, padlocks and other miscellaneous materials required for this work shall be supplied by the contractor]. Testing and commissioning the entire signalling installations jointly with the Railway representative at site at the stations/ LC gates covered under various schedules of the Contract, and ensuring that all the signalling gears are installed and adjusted as per the existing rules. The work also involves supply of required number of bound registers with good quality papers with all updated details of cable meggering, relays, batteries, block joints, route cancellation, relay room key entries, block instrument key, earth resistance etc., and handing over to Railways. (Supply of 'As mades' is not covered in this schedule).

60.00 diagrams, contact analysis charts, termination particulars of apparatus cases and cable termination rack, power supply arrangements, relay index board, cable plans, cable route plans, red boundary plans and all other particulars covered under various schedules. All AS MADEs shall be prepared by the Contractor in AUTOCAD 2000 or latest and submitted in CDs. One copy of the AS MADEs check print shall be submitted before Testing the circuits. The final negatives shall be made in tracing sheet (80 to 90 gsm). All AS MADEs except cable plan, cable route plan, bonding diagram & power supply diagram shall be prepared in A3 size. On approval the contractor shall submit along with the negatives, 8 copies in each, duly making booklet neatly bound. Out of 8 sets, 2 sets of drawings and other plans shall be kept in transparent plastic cover (2 sheets back to back in one plastic cover) and handed over to Railways. Also the contractor has to supply one set of AS MADEs in Reproduction Film . The approved circuit diagram will be issued by Railways in soft copy as well as two sets of hard copies. Wherever alterations to existing circuits are involved, the existing AS MADE circuit diagrams will be supplied by Railways either in CDs or RP film. The Contractor shall incorporate the details of all the new wirings and alterations in the CD/ RP film and submit them to Railways. On approval 8 copies shall be made for AS MADE circuit diagrams also as mentioned above. Designing of Signalling plan in AUTOCAD 2000 or latest and submission of negatives in 80/90 gsm tracing paper in 'U' size along with 2 copies and also the soft copy in compact disks induplicate. First, 2 sets of prints shall be supplied to Railways for checking. One set will be returned by Railways to the contractor for making corrections in AUTOCAD. The final corrected drawings shall be supplied to Railways on 80/90 gsm tracing paper and 2 CDs. [2 interlocked sidings will be considered equal for one loop line] (Approved permanent way plan will be supplied by Railways).

Station BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY

2.00 board/Warning board/ LEGEND boards along with rails, accounting and stacking them neatly at a place as instructed by Railway representative at site. Also the resultant pits shall be re-surfaced and consolidating by ramming and levelling.

6.00 Quarter size) without damage after releasing the shelf planks, Terminal blocks, Fuse Blocks, Terminal Boards, Relays of all types EKTs, Secondary Cells, power equipments, 'E' type locks, etc., and breaking the concrete foundation. After releasing, the resultant pits are to be closed and consolidated by ramming and levelling. The released materials shall be accounted and stacked at a place as instructed by Railway representative at site.

8.00 cable termination boxes, after releasing the base plank, Terminal blocks, Fuse Blocks, Terminal Boards, cut rails, pipes, etc., closing the resultant pits and consolidating it by ramming and levelling. The released materials shall be accounted and stacked neatly at a place as instructed by Railway representative at site.

6.00 Signals complete (upto 4 aspects) with or without Route Indicators, calling on signals, shunt signals etc., carefully without any damage to the gadgets, accounting and stacking them neatly at a place as instructed by Railway representative at site. The work includes breaking the concrete foundation, closing the resultant pit and resurfacing it by ramming and levelling.

8.00 machines (all types) including ground connections and other accessories available complete without any damage to the gadgets, accounting and stacking them neatly at a place as instructed by Railway representative at site.

2.00 along with surface base, signal post etc carefully without any damage, accounting and stacking them neatly at a place as instructed by Railway representative at site. The work also includes breaking and removal of concrete foundation and refilling of the resultant pit by ramming and levelling.

20.00 terminals after releasing all the bond wires. The released materials shall be accounted and stacked neatly at a place as instructed by Railway representative at site. Transportation of Signalling materials by road as per the instructions of Railway representative at site. The work also includes loading and unloading of the materials.

40.00 machineries for regarding and levelling the formation, dismantling any infringing structures, clearing and removing debris etc., with all leads and lifts etc., complete and as per the instruction of Railway representative at site. Total 3620591.95

Item Breakup - B-SOR Supply items

2.00 made out of 50mmX50mmX6mm thick MS angle POWDER COATED with stainless steel nuts and bolts for fixing the racks with suitable holes for hylem sheet complete as per standard practice with tripod bases and reel insulators. Cable ladder of 400mmx2000mm be provided at both sides with angle size 40mmx4mmx5mm with supporting flat of size 25mmx5mm.

800.00 up of PBT as per RDSO Drg.No. SA. 23756/ Adv/Alt.3, confirming to Specification No. IRS.S.75/2006 (Rev.2) or latest.

10.00 holders for Railway signalling, Rated voltage 240 AC/DC to Specn. No. IRS S.78/92 (IRS-S-78/97 Tentative) IS:13703 (part 2/sec2):1993 suitable for E1 fuse 20Amps SC-20 Holder Safe Clip / knife edge type size E1 (R-SS) amp. Fuse Block for Fuse Catridge

12.00 Specification.No.IRS :S-89-2013 ver 1.0 or latest. Charger shall be of 10Amp output capacity suitable for charging 80AH battery and No. Of Lead acid cells, 2/3/4.

300.00 Outer Dia, 10 mm Wall Thickness, along with one coupler for every 6 Meters as per specification No. IS 4984: 2016 with latest amendments and Material Grade:PE 80.

2.00 941760.00 1883520.00 HA- SSDAC) with Dual Track Sensor Devices as per RDSO specification No. RDSO/SPN/177/2012 version 3.0 or latest (Phase Reversal Type) as per details given below a) Configuration - 2 DP 1 section b) Length of cable required with each track device- 15 mtrs

10.00 Earth as per RDSO Spec No. RDSO/ SPN/197/2008 or latest and as per relevant Technical specification

200.00 Copper Cable as per IS: 694 for connecting Main Earth Electrode to MEEB in the equipment room. Color: Green

1.00 131287.00 110V AC, 2 Channels- 110V DC , 6 Channels- 24V DC) as per RDSO Spec./256/2002 or latest with 6 digit counter.

60.00 drawing with Colour (Power board diagram,Relay Foot index chart,Station Rule Diagram, FTOT Particulars, etc), as per instructions of Site In-Charge Railway Representative.

and maintanance registers for SSDAC, point machine, track circuit etc. (100 Pages each of 75 gsm paper)

6.00 89106.00 Duct (PLB-HDPE), 40/33 mm Dia, along with End Cap, End Plug, Cable Sealing Plug and Couplers, as per RDSO/SPN/TC/45/2013 Rev.2 (upto Amdt.2) or latest BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY

Termination WAGO/Pheonix/Elmex make or similar disconnecting Terminals blocks of size 1500mm x 500mm x 200mm thickness 1.6mm (16 SWG) 150 numbers of disconnecting terminal block with accessories. (The box should be divided in to two compartments 500 mm from TOP with door arrangement including locking, and bottom 1000mm closed fully with screws WAGO/Pheonix/Elmex terminals suitable for cable dimensions maximum of 2.5 sq.mm. Provision of easy and ensuring aesthetics.

8.00 Wago/Pheonix/Elmex make or similar

10.00 No.IRS-TC 77/2006 Revision1 or latest for quad cable. Total 4151265.00

Item Breakup - C-SOR Execution items

2.00 concreting tri-pod bases and reel insulators with "J" bolts and nuts. Tripod and other supporings are to be painted in 2 coats with enamel.

2.00 50502.00 Section digital Axle counter (SSDAC) with High Availability. HA-SSDAC to be installed, wired, tested and commissioned by OEM as per guidelines issued by RDSO, wiring discipline should be as per RDSO TAN No. STS/E/TAN/6001 Version 1.0 or latest. The pre-commissioning checklist issued by RDSO for SSDAC to be prepared by OEM and jointly signed by OEM & Railway. Before commissioning of HA- SSDAC, OEM should submit site installation certificate.

80.00 separation of 8 cms each to a depth of 150 mm in the platform surfaced/tiled floor for laying cable.

60.00 Thickness along with collars in trenches at places of platform cutting etc., and wherever required as per the instructions of site engineer.

60.00 pipe/DWC/HDPE pipe in which cable is already laid to a size of 300*300mm with 1:3:6 mortar. (All the matetrials required for the work should be supplied by the contractor){Per Unit- RMT}

10.00 per RDSO specification No.RDSO/ SPN/197/ 2008 or latest and as per Technical Specification

2.00 termination of cables on Wago/krone connectors as per the instructions of the site Engineer.

6.00 complete for 6 quad cable. After the jointing the through cable has to be tested for insulation resistance and loop resistance in presents of Railway Engineer and in case of any defects the jointing has to be done at free of cost by the contractor. [Heat Shrinkable jointing kit conforming to RDSO specificaiton No.IRS-TC 77/2006 covered in the supply portion has to be used for this purpose. The Contractor should supply all other small items free of cost which are required for making a joint. Only gas blower to be used for blowing BANGALORE DIVISION-S AND T/SOUTH WESTERN RLY Total 369244.00

Item Breakup - D-SOR Supply and installation items

6.00 20031.00 Copper Plate Earthing System complete with provision of (i) Copper plate 300mm X 300mm X 3 mm, (ii) Earth Pit 6 ft depth filled up with charcoal 10 kg & salt 25 kg in alternate layers up to 2 ft from bottom, (iii) Water funnel on Perforated GI pipe of length 4.5 ft., (iv) Cast Iron top plate 12" x 12" (v) Drawing of copper - earth from earth to location with 25 mm x 3 mm copper strip for termination(all miscellaneous materials to be supplied by the contractor)

50.00 On/STOP/BSLB/Legend boards as per practice & SEM (Angle/Rail is to be supplied by Railway).

4.00 Interlocked LC Gates, made of Teak wood with Glass fronted door as per drawing 03/91. Polishing on all exposed surface and for with EKT inside the box. Micro push switch of L&T make with 2NO+2NC contacts and veeder counter non-reset type and wire them as per the approved circuit diagram. The box should have hinges and pad locking arrangements with one No.40 mm Navtal-Lock with duplicate keys and key chain with label. (All materials except EKT are to be supplied by the contractor).

3572.00 Duct) of 500mm Width as per Drg. No. SDO/Cable laying/ 007 (Annexure-10), as detailed in document No. RDSO/SI/G/2010 Ver.1.1 or latest on 'Guidelines on signalling cable laying'

200.00 mm dia, 2 meter long in already dug cable trenches. The unit of RMT means two split pipes of 1 Mtr each. Material shall be supplied as per specification RDSO/SPN/204/2011 or latest" {Per Unit-RMT}

1.00 34673.00 Cum Key Lock Relay Box (of MS Sheet) along with LEDs, with approved type push buttons, Wago or similar Disconnecting type Terminal Blocks inlcuding DIN rail etc., as per tentative drawing enclosed. Installation, fixing and wiring of boxes for Key Lock Relays to be carried with Contractor's wiring and fixing material. The work shall be carried as per the instructions of site engineer.

100.00 pipe of minimum 25 mm size or higher as per requirement at site on the wall/floor etc., using bends, coupler and T joints and flexible pipe wherever necessary with fixture in the OFC room from equipment rack to common termination and from OFC room to SM room/Reservation office /Data logger/FOIS room etc. (All required material for fixing to be arranged by the contractor) Total 5115251.00

Item Breakup - F-SOR UFSBI and RTU items

4.00 97392.00 mountable,Optical module integrated in the unit supporting dual OFC and one 100 MBPS Ethernet and two Sub E1 as per ITU standards or 8E1 port(1+1 protection) optical distance support upto 25 kms, unit to support 124/248 DSO level cross connect and one E&M module supporting eight 2W/4W ; with dual DC(48 V dc)/AC power supply; one 50 SCSI pin cable along with unit; similar to MAPLE 4CS/OFC/DC&Module 2W/4W Total 389568.00