REPAIRS TO PLASTERS, LEAKAGE/SEEPAGE, SUNKEN, PVC WATER TANKS, TANK PLATFORMS, PLUMBING, REPAIR TO CHAJJAS, BEAMS, COLUMNS AND ASSOCIATED B/R WORKS AT N AREA UNDER GE CHANDIGARH

Amount

Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Demolition of Cement concrete unreinforced as in Ground Floor and paving n. exc. 15cm thick (above or below G.L.) complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts complete all as specified and directed by Engineer-in-Charge.

Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description not exc 1 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.

Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and refixing in the same opening complete all as specified and directed by Engineer-in-Charge.

Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc, removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 110mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed.

Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 75mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed.

Dismantling wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete, all as specified and as directed by Engr-in-charge.

Demolition of entire Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings etc complete all as specified and directed.

Dismantling Plain or corrugated fiber sheet etc any gauge, thickness, complete all as specified and directed.

Taking up or down kitec pipe and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down kitec pipe and connections of 25mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones (up to 4th storey of building ) complete all as specified and directed by Engr-In-Charge.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring etc., and making good, cutting not exc 10 cm girth and complete all as specified and directed by Engineer-in-Charge.

Disconnecting/dismantling existing tanks of capacity exc. 500 ltr & n. exc. 1000 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Disconnecting/dismantling existing tanks of capacity exc. 250 ltr & n. exc. 500 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks exc 250 ltr and n exc 500 ltrs in capacity for cleaning and removing all scale and dirt etc, from tanks and from mouths of circulating pipes etc and reconnecting and re-fixing in position complete all as specified and as directed.

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quions arches, pillar or any other descrption etc complete all as specified and directed by Engineer-in-Charge.

Demolition of cement concrete of any description and in any position complete all as specified and directed by Engineer in Charge.

Demolition of water tank base of stone/boulders masonary,bricks etc, built in Cement mortar or cement lime mortar including all quoins,arches,pillers etc but excluding ashlar facing etc including removing to out of MOD land complete all as specified.

Installation of rebar by using Hilti hammer drill with carbide drill bit,chemical sispensing gun for inserting RE-500V3 chemical upto minimum depth of (10 x dia of bar ) as in chajja,beam,lintel,column slab and parapet at any height before inserting an anchor bar.Hole must be free from dust debris,water,oil grease complete all as per manufacturers instructions. Note :- (i) Reinforcement shall be measured and paid separately. (ii) Rates are inclusive of form work and safety measures. (iii) Dia of bar 10/12 mm

Supplying & fixing of PVC water storage tank 1000 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including 20/15 mm tank nipple, supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete Note : (i) Inlet, outlet & wash out pipe will be measured paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

Supplying & fixing of PVC water storage tank 500 ltr capacity HDPE triple layered ,white colour cylindrical type fixed and hoisted in position on roof at any height complete with inlet/outlet of 20 mm GI Pipe connection incl locking arrangement, including 20/15 mm tank nipple, supplying & fixing of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete Note : (i) Inlet, outlet & wash out pipe will be measured paid for separately. (ii) The quoted rate is inclusive of minimum one union each on inlet and outlet of water tank as per size of pipe shall be provided.

S&F for tank Nipple suitable for HDPE water tank 20mm tank nipple cast iron min weight 45gms complete all as specified.

S&F for tank Nipple suitable for HDPE water tank 15mm tank nipple cast iron min weight 45gms complete all as specified.

Supplying & fixing in repairs of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 15 mm Gun-metal, globe or gate valves, with MS lever handle, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs 20 mm Gun-metal, globe or gate valves, with MS lever handle, screwed both ends for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

25 mm thick Cement concrete (1:2:4) type B-0,using 12.5 mm graded mechanically crushed stone aggregate as in levelling concrete etc. complete all as specified and directed by Engineer-in-Charge.

75 mm thick, cement concrete type C-2, 1:3:6 using 40 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, complete all as specified.Plinth protection shall be laid in 1:20 slope and joint filling sealed with bituminous sealing compound grade "A" .

Plain cement concrete (1:4:8) type D-2,using 40 mm graded stone aggregate as in foundations, filling and mass concrete, sub base to paver blocks etc complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete (1:7:12) type D-2,using 40 mm graded stone aggregate as in sunken floor etc complete all as specified and directed by Engineer-in-Charge.

Plain cement concrete 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in cement concrete in roof kerbs or roof padding,mud stops, rounded or chamfered on edges with recron 125 gm per cement bag with and including using necessary use and waste of formwork for fair finished surface complete all as specified and directed by Engineer-in-Charge.

Reinforced Cement Concrete Nominal mix ( 1 :2:4) using 20mm graded mechanically crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engineer-in-Charge.

TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

TMT steel bars 6mm to 8 mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardner, resin in the ratio of 8:1:2 laid mortar over and inculding 15 mm thick screed in cement mortar (1:6) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in floors etc. set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardner, resin in the ratio of 8:1:2 laid mortar over and inculding 15 mm thick screed in cement mortar (1:6) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.

Vitrified ceramic tiles double charged light shade 10 mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floor etc set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardner, resin in the ratio of 8:1:2 laid mortar over and inculding 15mm thick screed bedding layer in CM (1:6) complete all as specified and directed by Engineer-in-Charge.

Glazed ceramic coloured tiles 450 x 300 x 7mm thick on vertical surface such as skirting , dado etc. over and including 10 mm thick rendering in CM 1:4 thick set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desired shade, hardner, resin in the ratio of 8:1:2 complete all as specified and directed by Engineer-in-Charge.

Granite 18-20 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:3) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge.

Machine cut Kota stone slab flooring 20-22 mm thick,SIZE 55 CM x 55 cm laid over & including 20 mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.

Machine cut Kota stone slab 20-22 mm thick as in skirting, dado and pillars "riser/tread" etc , laid over & including 10 mm thick rendering in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.

Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 EXCEPT BRICKS complete all as specified and directed by Engineer-in-Charge.

Rubber coated Chequered cement concrete tiles 300mmx300mmx25mm thick with grey cement and pigment, over and including 20 mm thick screed in Cement mortar 1:4 set jointed and pointed in neat cement slurry in floors complete, all as specified and as directed by Engineer-in-Charge.

Water proofing roof treatment and sunken treatment using APP polymeric water proofing membrane minimum 3 mm thick and weighting not less than 3.6 Kg/Sqm black finish reinforced with non-woven polyster matt wt not less than 150 gms/Sqm with thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/Sqm over cleaned surface including parapet,applying a coat of blown bitumen 85/25 grade @ 1.2 kg per square metre over priming coat torching over laps with a propane or butan gas torch with a over lap of 100 mm at the side and 150 mm at the ends and sealing all as per manufacturers instructions incl wire brushing and cleaning the top surfaces of concrete, roof surfaces etc. with water including flashings and junction of parapets etc complete all as specified and directed.

M&L for raking out joints/ pointing to brick to brick tiles 30cm by 15cm laid flat as in floors, roofs, ceilings, chajjas, etc compound complete all as specified.

Rendering 15 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces with water proofing compound on top layer, trowelled to even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

Rendering 15 mm thick in cement mortar 1:4, on roof surfaces including flashings and junction of parapets,brick or concrete surfaces with water proofing compound on top layer, trowelled to even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.

Supply only liquid water proofing comound ISI Marked complete all as specified and directed.

Rendering 10 mm thick in cement mortar 1:3 as in ceiling/soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered surfaces of wall and applying two coats of cement base paint on walls over and including a coat of primer including preparation of surface complete all as specified and directed.

Preparation of plastered or unplastered new surfaces of ceilings and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper on walls over and including a coat of chalk whitening including preparation of surface complete all as specified and directed.

M&L for complete removal of existing surface and applying two coat of oil bound distemper over a coat of Chalk whiting, on plastered surfaces incl preparatory to distempering and primer on wall surfaces complete all as specified and as directed.

Preparation of old Plastered or un-plastered surfaces of ceilings etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of white wash on ceilings/ old decorated surfaces complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.

25 mm thick factory made Flush shutters, solid core construction, with particle core and plywood face panels, commercial type on both sides face covered with decorative face veneer with lipping/frame to match supplied and fixed complete all as specified and directed by Engineer-in-Charge.

Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles),With Wood free EPS with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification to be fitted in the MS frame welded/scaled to the stiles & rail with suitable PVC sheet beading & jointed together with solvent cement supply & fixing in the frame at site as per specification & drawing.

35 mm thick factory made Plain, framed, panelled shutters of 2nd class Hardwood (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkat complete all as specified and directed by Engineer-in-Charge.

35 mm thick factory made glazed & Skeleton shutters of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.

Solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.

Factory made box type steel windows with pressed steel frame min 1.25 thick complete including mild steel acessories like lugs, door stopper, holdfasts, pintol hinges, handles( minimum One for each shutter), and ISI marked tower bolt 150mm size (minimum 2 for each shutter) etc. with glazing bars and without glazing bars (Double shutter ) dovetailed or welded with one shop coat of zinc chromate primer, complete all as shown on drawing No. TD-276(R), Sheet No 1/4 to 2/4, 3/4, 4R/4 and as specified and directed by Engineer-in-Charge. Note: (i) Fabrication as per TD-276 (R) SH 1/4 to 2/4, 3/4, 4 (R) /4 (ii)Mode of measurement Unit will be for the complete window except Glass/ Gauge but incl fittings, ISI marked iron mongery complete as per TD. (iii) The PCC back filling in chowkhat of window, Grills,Sheet glass and wire gauge will be measured and paid separately against respective items.

Factory made box type steel ventilator with top hung or fixed half glass and half wire mesh portion shutter including projecting type hinges, steel peg stay, complete all as specified and directed by Engineer-in-Charge.Note:Sheet glass and wire gauge will be measured and paid separately against respective items

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions frame with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified and directed by Engineer-in-Charge.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per drawings and the directions of Engineer-in-Charge

S&F aluminium window jali for windows, ventilators with one or more rebates including joining cleat/aluminium beading for fixing etc complete all as specified.

Aluminium anodised,barrel tower bolts of extruded section with length of bolt 200 mm and dia of bolt not less than 10 mm,ISI marked complete all as specified and directed by Engineer-in-Charge.

Aluminium anodised,barrel tower bolts of extruded section with length of bolt 150 mm and dia of bolt not less than 10 mm,ISI marked complete all as specified and directed by Engineer-in-Charge.

100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed by Engineer-in-Charge.

S&F butt hinges 100mm size medium weight cold rolled mild steel of any frame as wooden/metal through nut&bolt/welding complete all as specified and directed.

300 mm long,Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified & directed by Engineer in Charge.

150 mm long Aluminium handles, cast type,anodised complete all as specified and directed by Engineer-in-Charge.

125 mm long Aluminium handles, cast type,anodised complete all as specified and directed by Engineer-in-Charge.

100 mm long Aluminium handles, Fancy type,cast type,anodised complete all as specified and directed by Engineer-in-Charge.

Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor with overall length of cover plate 150 mm complete all as specified and directed by Engineer-in-Charge.

Peg stays of aluminium alloy anodised 150 mm complete all as specified and directed by Engineer-in-Charge.

S&F in Hasp and staple 125 mm alluminum anodised complete all as specified and direccted.

S&F M.S.helical spring 300mm longe including roller & roller plate complete all as specified and directed.

S&F in repair Continuous (piano hinges) 30mm width of flap in repairs Paino hinges, mild steel bright finish (width of flap 30mm) complete all as specified and directed by Engineer-in-Charge.

S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, bright finished complete all as specified and directed.

Aluminium body peg set of 06 pegs complete all as specified and directed by Engineer-in-Charge.

S&F in repair door ceal 120cm long complete all as specified and directed.

M&L for door closer hydraulically regulated, designation No. 1 universal type, aluminium body suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and directed.

M&L for floor door spring hydraulically regulated, cast iron body designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and as directed.

Stainless steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

Sheet glass 4 mm thick, ordinary quality and glazing with linseed oil pane putty & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane complete all as specified and directed by Engineer-in-Charge.

4 mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm each and using Silicon for fixing of glass in addition to glazing putty complete all as specified and directed by Engineer-in-Charge.

S&F 5.5 mm thick sheet glass pane tinted/plain/Figured glass type, with 5 micron thick black film ordinary quality and ruber, cleting, silicone,glazing with oil putty etc in each pane complete all as specified and directed.

Material & labour for 25mm dia stainless steel pipe curtain rod, powder coated fixed with & including stainless steel hooks/ brackets and decorative finials (at both side), curtain rings (minimum 5 Nos rings per running mtr of curtain rod) shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook including taking out the existing old pelmet box along with old curtain rods complete all as specified and directed.

Mild Steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging conforming to Fe-290 (Gde E-165), also fastening and fixing complete all as as specified and directed by Engineer-in-Charge.

S&F fot tank base angle, Joist, channel, or tee sections, fixed independently by means of welding, without connecting plates, etc. confirming Fe 410-W(Gde-E-250) quality B complete all as specified and directed.

Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, Fe-410-W (Gde E-250) complete all as as specified and directed by Engineer-in-Charge.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates "grills" etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed by Engineer-in-Charge.

Pre-painted galvalume aluminum zinc coating profile sheet GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

Pre- painted galvalume aluminum zinc coating profile sheet GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping s crews as complete all as specified and directed.

M&L 2 mm thick Fibre glass reinforced transparent plain/corrugated sheeting of white or any colour fixed with coach screw and washer in roof, wall etc complete all as specified.

S&F 18/19 mm thick HDHMR both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in cupboards and other accesories etc as in repairs complete all as specified and as directed.

PVC hollow wall panelling 5mm thick any colour/design approved by engr-in-charge, inclusive of fixing on to wall incl moulding end caps fixed with PVC sleeves and screws as required at site including dismantling of walls and ceiling boards/wall paneling or insulation board any thickness, including cover fillets complete all as specified and directed

9 mm thick PVC prelaminated Gypsum board ceiling including anodised aluminium snap grid framework for ceiling having grid size 605 x 605 mm comprising of wall angle of size 25 mm x 25 mm x1.3 mm,main runner of size 38 mm x26 mm x1.3 mm.The grid system will be suspended at every 1200 mm c/c in both directions by using 3.5 mm dia aqualine wire fixed to purlins or RCC roof with suitable fastener to with stand the load of grid system with ceiling board as per manufacturers instructions complete all as specified and as directed by the Engineer-in-Charge.

S&F in repair for Vitreous China wash down water closet pan ( pedestal pattern) white ( excluding flushing cistern and flush pipe) including plastic water closet seat cover white with 1 m hose pipe, closed pattern with flat botton and cover and mild steel chromium plated or aluminized hinging device incl P or S trap with connection complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with PVC `P’ or `S’ trap, integral foot rest including connection to trap and flushing pipe, etc complete and bedding in PCC 1:7:12 type F-2 complete all as specified and directed.

S&F for vitreous china white wash basin with flat back of size 550mmx400mm coloured including MS brackets, cutting for and pinning in ends of brackets, including bottle trap/ PVC waste pipe as in repairs complete all as specified and as directed.

S&F single piece WC of size 365x655x765 with flushing cistern and connection pipe, P or S trap (closed pattern incl all necessary accessories like rag bolts, kitt /gel gasket etc, (including flushing cistern, pvc seat cover , jet and flush pipe complete all as specifed and directed.

S&F in repair vitreous china Urinal, Half stall type, white (excluding flushing cistern) including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screw, pointing around urinal back in cement, grating and union for discharge pipe incl brass cp waste coupling, waste pipe, brass cp urinal spreader complete all as specified and directed.

S&F automatic sensor for urinal including all connections with flushing pipe and outgoing pipes fixed in repairs complete all as specified and as directed.

S&F for one piece PVC hydrolica plastic water closet seat cover (white coloured) closed pattern with flat bottom, cover and mild steel chromium plated or aluminium hinges device for pedestal pan fixed as in repair complete all as specified and as directed.

S&F in repair 10 ltr capacity PVC valveless, syphonic action dual flush type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe complete all as specified and directed by Engineer-in-Charge.

S&F for centre hole basin mixer 15mm dia with spout, fancy type, chromium plated Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed as in repair complete all as specified and as directed.

S&F for wall mixer 15mm dia with spout, fancy type, chromium plated Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixedas in repair complete all as specified and as directed.

S&F for Sink mixer 15mm dia with spout, fancy type, chromium plated Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixedas in repair complete all as specified and as directed.

S&F 15 mm bore fancy type Pillar taps, cast copper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed to 15 mm bore iron pipe as in repair complete all as specified and as directed.

Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs stop/angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated complete all as specified and directed by Engineer-in-Charge.

Supplying and fixing in repairs stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup (Concealed type) complete all as specified and directed by Engineer-in-Charge.

Supply & fix in repairs chromium plated, Brass, Jet spray including flexible pipe 15mm bore, screwed down, high-pressure pipe of 15 mm bore with wall flange fixed to wash down water closet (pedestal pattern) complete all as specified and directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified as directed

S&F Brass chromium plated shower rose 150mm square in shape with 450 mm long arm fixed in repair complete all as specified and as directed.

S&F in repairs toilet papper holder chromium plated with fixing to wall complete all as specified and directed.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as complete.

S&F Bib tap standard of PTMT with flange Minimum weight 15mm-5gms any colour high pressure screwed for iron pipe and fixed .(Minimum weight 15mm-90gms fixed in repair incl PTMT extension Nipple (Minimum weight 15mm-18 gms) fixed in repair complete all as specified.

S&F in repair urinal waste pipe 32mm dia, 800mm long with cup and nuts fixed to urinal complete all as specified & directed

S&F in repair Flush pipe of polyethylene of low or high density or PVC 32 mm dia, long bend, for low level cistern Complete all as specified and directed complete all as specified and directed.

S&F for Soap dish, vitreous China white, approximate size 160x 160x90mm fixed in repair complete all as specified and as directed.

S&F for PVC connections with PTMT nuts of length 600 mm long fixed to 15 mm bore iron pipe or union as in repair complete all as specified and as directed.

S&F in repairs steel grating 100mm dia complete all as specified and directed.

110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with and including MS clamps made out of flat iron of size 25 mm x 3 mm including nuts,bolts complete all as specified and directed by Engineer-in-Charge.

110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches complete all as specified and directed by Engineer-in-Charge.

75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore fixed in repair including jointing to waste pipe in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer in Charge.

PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC(SWR) bends (any radius), for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) junction (Single T) equal or unequal for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) junction (Single T) equal or unequal for 110 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) trap ‘P’ including jointing with solvent cement 100 mm bore fixed in repair complete all as specified and directed by Engineer in Charge.

CPVC(SDR-11) of outer dia 20 mm with and including CPVC SDR-11 fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC(SDR-11) of outer dia 25 mm with and including CPVC SDR-11 fittings on walls and ceilings or laying in floors complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 brass elbow fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 brass TEE fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 UNION fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Tank Adaptor nipple fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Ball valve fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

CPVC SDR- 11 Female Brass Threaded Adaptor (FTA/ FBTA) fittings, ISI marked for CPVC pipe outer diameter 20 mm bore complete all as specified and directed by Engineer-in-Charge.

S&F tubes 15 mm, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including clamps and screws fixed on rawal plugs complete all as specified and directed by Engineer-in-Charge.

S&F tubes 20 mm, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including clamps and screws fixed on rawal plugs complete all as specified and directed by Engineer-in-Charge.

Re-fixing only tubes, any grade, to walls and ceilings or laying in floors 15 mm, `medium grade' galvanised, with all fitting and fixed clamps and screws fixed on rawal plugs complete all as specified and directed by Engineer-in-Charge.

Re-fixing only tubes, any grade, to walls and ceilings or laying in floors 20 mm, `medium grade' galvanised, with all fitting and fixed clamps and screws fixed on rawal plugs complete all as specified and directed by Engineer-in-Charge.

M&L for two coats of synthetic enamel paint over old painted wooden or wood based surfaces of any description, not otherwise described over 10 cm width or girth, including preparation of surfaces complete all as specified.

S&F Kitec all fittings coupler 16/20 all fittings in kitec and fixture fixed & concealed in wall/ceiling or laid in floors complete all as specified and as directed.

S&F Kitec all fittings coupler 20/25 all fittings in kitec and fixture fixed & concealed in wall/ceiling or laid in floors complete all as specified and as directed.

S&F Kitec all fittings tee,elbow, coupler all fittings in kitec and fixture fixed & concealed in wall/ceiling or laid in floors complete all as specified and as directed.

Note: For the purpose of arriving at lumpsum amount, the amount of credit schedule i.e Sch 'A' section II (i.e Rs 1,00,845.00 shall be deducted from the total amount arrived.

Total of Schedule 'A' Rs.

M/s Super Trading Corporation (BID ID -3354215)

M/S MATLOOB AHMED (BID ID -3350690)

His Construction Company (BID ID -3354321)