Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹94.0 LAccepted-Finance | L1 | Accepted-Finance Being L1 | |
| 2 | L2₹96.2 L+₹2.2 L (2.39%)Rejected-Finance 60 MADHUVAN BANK COLONY ALWAR | L2 | Rejected-Finance Being L2 |
Tender Value
Refer Docs
EMD Value
₹1.9 L
Closing Date
28 Mar 2023, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE Alwar
GE Alwar
REPAIR TO DUS CONSTRUCTED UNDER MAP PHASE-I AT ALWAR MIL STN
2023_MES_580075_2
8134/E8
Open Tender
Civil Works
Item Rate
180 days
Alwar
As per NIT
3 documents required · 3 mandatory
₹1,000
Yes
GE Alwar
₹1.9 L
Yes
31 Mar 2023
13 Mar 2023
30 Mar 2023
13 Mar 2023
28 Mar 2023
15 Mar 2023
13 Mar 2023 - 14 Mar 2023
Amount
Demolition of cement concrete (unreinforced) other than ground floor and paving n exc 15 cm thickness (below or above ground level) & removal complete all rubbish materials complete all as directed.
M&L rendering 15mm thick in CM 1:4 on brick work or concrete surface mixed with WPC 3% by wt of cement and finished even and smooth with using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid as supply only here-in-after.
M&L one coat of cold bituminous primer at the rate of 0.25 litre/sqm on plaster surfaces including side walls there after a layer of APP based polymeric membrane reinforced with polyester non woven fabric (weighing not less than 150 gms/sqm) weighing 3kg/sqm and 3mm thick laid on the primed surface by torch application, side overlaps shall be 75mm and at the ends 100mm. All over laps and the joints shall be scaled properly. A cushion layer of coarse sand of thickness 25mm shall be provided to protect polymeric membrane.
M&L cement concrete 1:5:10 type E2 using 40mm brick aggregate for sunken portion all as specified and as directed.
S&F 32mm dia GI spout to drain out leakage, the mouth of GI pipe shall be filled around the gravel to avoid choaking. Top of sunken portion of RCC slab to be finished such that it slopes towards spout complete all as specified and directed.
M&L 100mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate as in sub base/mass concrete complete all as specified and directed.
M&L 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded aggregate) as in levelling coarse of floors and roof.
S&F vitreous china squatting pan of orrisa pattern size 580mm x 440mm white with integral foot rest (excluding flushing cistern and flush pipe complete incluidng provision of lime concrete bedding complete all as specified and directed.
M&L screed bed or bedding layer 15mm thick in CM 1:6 for laying floor finishes complete all as specified and directed.
M&L non skid ceramic colour joint free tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11 Sqm but n. exc 0.18 Sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed.
Dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.
M&L 10mm thick cement plaster in CM 1:4 on other than fair faces of brick work or stone surfaces of walls to receive tiles etc complete all as specified and directed.
M&L glazed ceramic tiles (coloured) in vertical surface 350mm x 250mm x 7mm / 450mm x 350mm x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.
Taking down cement or cement lime plaster, of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.
M&L rendering 5mm thick in CM 1:3 as in ceiling and finish the surface even and smooth without using extra cement complete all as specified and directed.
M&L rendering 10mm thick in CM 1:4 on fair face of brick work as on wall surfaces and finish the surface even and smooth without using extra cement complete all as specified and directed.
M&L rendering 15mm thick in CM 1:6 on stone masonry surfaces or surfaces other than fair face of brick work as on wall surfaces and finish the surface even and smooth without using extra cement complete all as specified and directed.
Supply only integral water proofing compound.
M&L preparing newly plastered surfaces & applying three coat of white wash on ceiling complete all as specified and directed.
M&L preparation of newly plastered surface of wall & applying two coats of cement base paint over a coat of primer white wash complete as specified and directed.
M&L preparation of new plastered surfaces of wall & applying two coats of distemper oil emulsion white or tinted over priming plastered surface with alkali resistant priming paint complete as specified and directed.
S&F bends 100mm bore diminishing pieces or tapers (larger bore will be measured) complete all as specified and directed.
S&F in repair cast iron soil, waste and vent pipes 100mm bore in any length with or without ears, with cement joints, fixed on walls complete all as specified.
Cutting holes into stone wall n.exc half brick built in cement mortar or cement lime mortar for inserting hold fast and making good disturbed surface portion in CM (1:3) or cement concrete (1:2:4) type B-1 exc half brick but n exc one brick as required complete all as specified and directed.
M&L water proofing treatment on roof surface in following sequence through manufacturer / authorised applicator of the manufacturer complete :- (i) Properly cleaning and drying concrete surfaces. (ii) Applying a coat of bitumen primer @ 0.25 Kg/sqm (iii) APP based Polymeric membrane reinforced with polyester Non woven fabric (weighing not less than 150 gms/sqm) weighing 3kg/sqm and 3mm thick laid on the primed surface by torch application, side overlaps shall be 75mm and at the ends 100mm. All over laps and the joints shall be scaled properly. A cushion layer of coarse sand of thickness 25mm shall bve provided to protect polymeric membrane. (iv) M&L 22mm thick PCC tiles ISI marked laid over 15mm thick bedding mortar in CM 1:6 PCC tiles will be jointed with neat cement slurry and 4mm wide & sealed with 2mm deep polysulfide compound. (v) Coveted fillet in PCC (1:2:4) type B0 of radius 75mm provided at the junction of roof and parapet/mumty/oyher vertical surfaces and surface painted with paving bitumen penetration value 30/40 conforming to IS:73 @ 1.2 kg per sqm over a coat of bituminous primes, conforming to IS:3384 @ 0.30 litre/sqm.
Taking down chowkhats or frames not exc 1.5 sqm each complete all as specified and directed.
M&L pressed steel size 105mm x 60mm frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.
M&L preparation to new or previously untreated steel surface of any description, over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of zinc chromate primer complete all as specified and directed.
M&L providing and injecting chemical emulsion for post constructional anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre per linear metre including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors drilling and plugging holes etc complete all as specified and as directed.
M&L providing and injecting chemical emulsion for post constructional anti termite treatment of voids in masonry, alongwith wall below concrete or masonry apron using chemical emulsion @ 1 litre per holes, soil under existing floors using emulsion @ 1 litre per hole including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) and match the existing floor complete all as specified and as directed.
M&L providing and injecting chemical emulsion for post constructional anti termite treatment of soil under existing floor using chemical emulsion 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) and match the existing floors using emulsion @1 litre per hole complete all as specified and directed.
M&L providing and injecting chemical emulsion for post constructional anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with cement mortar 1:3 & painted with white or coloured paint complete all as specified and as directed.
M/S JINDAL ENTERPRISES
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .