SR TO RB TYPE-VIII HOUSES UNDER MTC. BOOTH SECTOR 23 CHANDIGARH. (HOUSE NO. 118)

Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge.

Providing and fixing 60 mm thick high density rubber moulded precast cement concrete paver block grey/ colored/ polished/ designer (manufactured by vibro hydraulic pressure process) consisting of design mix of cement, sand and fine aggregate having designation M35 ISI marked including the cost of good quality color and hardening agents. The paver should be compiled with tensile strength and breaking load as per BIS 6717-1993 and shall be tested against resistance to bear as per IS 1237-1980 (specification for cement concrete floor tiles). The paver should be laid over layer of 25 mm average thick screened coarse sand to the required slope and filling the joints with fine sand complete in all respects and to the entire satisfaction of Engineer in charge.

Providing and fixing 3.0 mm thick clear polycarbonate sheet to be fixed on the existing MS / wooden frame with self drilling machine screws including remove the old polycarbonate sheet complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and fixing 1.5mm thick polycarbonate sheet to be fixed on the existing MS frame with self drilling machine screws complete in all respect to the entire satisfaction of Engineer-in-charge.

15 mm cement plaster on the rough side of single or half brick wall of mix: 1:4(1 cement: 4 fine sand)

Providing and laying water proofing coating having three coats of water proofing chemical with 1 coat as primer and 2 subsequent coats. The water proofing chemical shall have properties as water absorption 1% minimum, pot life at 30º C : 30 min, application temperature 10º C, bond strength to concrete : approx 1 N/mm2. (Fosroc Hydroproof xtra or equivalent) . The primer coat shall be provided in ratio 1 part of Hydroproof Xtra :2 parts of water : 4 parts of cement mixed material with the above proportion will cover an area of 16-17sqm for 1 L of Hydroproof XTRA . The two top coats shall laid in ratio 1:2 i.e. 1 part of chemical and 2 parts of neat cement after laying of 800 micron fibre mesh. The thickness of each coat shall be about 1 to 2 mm. The 2nd coat shall be applied after 5-6 hours of 1st coat. The full curing shall be done after 12 hours with must curing after 6 hours. The coverage of top coats shall be 4.5-5.0 sqm /litre/ coat. The work shall be undertaken as per manufacturer specifications, complete in all respect and to the entire satisfaction of Engineer in Charge.

Providing and fixing stainless steel finish tower bolts (barrel type) of size 250x 10mm with necessary s.s. screws etc. complete in all respect and to the entire satisfaction of the Engineer in charge.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. One coat

Providing plaster of paris (minimum 2mm thick) punning over walls with after scraping old white wash / distemper from the existing surface including chipping of surface and cost of scaffolding etc. to prepare smooth and even surface complete in all respect and to the entire satisfaction of the Engineer in charge.

Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (One or more coat applied @0.90 Itr/10 sqm).

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: One or more coats on old work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and fixing stainless steel finish handles of size 125mm with necessary s.s. screws etc. complete in all respect and to the entire satisfaction of the Engineer in charge

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4(1 cement :4 coarse sand)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Providing and Fixing 35mm thick golden champ wood (kiln seasoned) wire guage door shutter consisting of 100mm x 35 mm style and top rail 150 mm x 35 mm lock rail 200mm x 35 mm bottom rail wire mesh 22 x 12 mm gauge fixed with 1/2” x 3/4” golden champ wood (kiln seasoned) beading, with two vertical members in each panel to hold wire mesh, with necessary 4 Nos. of hinges 4", 2 Aluminium Tower bolts 6", 2 Aluminium Handles 5” and Aluminium door stopper and single acting door spring and complete fixed in position including two coats of paint and one coat of primer after preparation of surface (special quality) Complete in all respect to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 35mm thick golden champ wood (kiln seasoned) wire guage window shutters consisting of vertical and horizontal styles 75x35mm size with wire mesh 22 x 12 mm gauge fixed with 1/2"x3/4" golden champ wood (kiln seasoned) beading. The rate further includes the cost of 3" hinges, Aluminium tower bolts 4", Aluminium handles 1 nos., I-hook and two coats of special quality enamel paint over coat of primer after preparation of surface (special quality) complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and fixing 35mm thick golden champ wood (kiln seasoned) glazed window shutters consisting of vertical and horizontal styles 75x35mm size with 4mm thick floated glass pane fixed with 1/2"x3/4" golden champ wood (kiln seasoned) beading. The rate further includes the cost of 2 nos. 3" hinges, 2 nos. Aluminium tower bolts 4", Aluminium handles 1 nos., I-hook and two coats of special quality enamel paint over coat of primer after preparation of surface (special quality) complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and fixing 35mm thick phenol bounded factory manufactured solid flush door shutter ISI marked with both side commercial face in the existing chowkhat. The rate includes the cost of iron hinges, all necessary Aluminium fittings and painting two coats over one coat of primer after preparation of surface (special quality) complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and laying antiskid ceramic floor tiles of specified size (thickness to be specified by the manufacturer) of 1st quality with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand). The tiles are to be fixed by provding 2 mm thick spacer. The area of spacer is to be filled by using cement based grout of approved shade. The grooves are to be filled with cemenitious grout mix with proportion of 0.90 kg grout and 0.10 kg of hardener for each kg of filling material complete in all respect and to entire statisfaction of Engineer-in-Charge. Size of tile 300x300 mm

Providing and laying vitrified floor tiles of size 600 x 600 mm single charge (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade. The tiles are to be fixed with 3mm grove using spacers. The tiles are to be laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm The grove are to be filled with cementitious grout mix with proportion of 0.90 kg grout and 0.10 kg of hardener for each kg of filling material. Single charge vitrified tile of size 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles of size 300 x 600mm conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades as approved by Engineer-in-charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand). The tiles are to be fixed by providing 2mm thick spacer. The area of spacer is to be filled by using cement based grout of approved shade. The groves are to be filled with cementitious grout mix with proportion of 0.90 kg grout and 0.10 kg of hardener for each kg of filling material complete in all respect and to the entire satisfaction of Engineer-in-Charge

Dismantling of ceramic tiles or vitrified and plaster to making the surface clean for refixing the glazed tiles including removing of malba complete in all respect and to the entire satisfaction of the Engineer in charge.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Please Enable Macros to View BoQ information