Provision of Galvanised Sheet cover against Rain for Certain Buildings 40 in Nos at NOFRA Provision of Sign Board for Roads at NOFRA Provision of Visitors Room near Main Gate of NOFRA II and certain Revenue and Minor Works under GE Gomantak

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out from soft/ disintegrated rock complete as as specified and directed.

Material &Labour for plain Cement concrete Type D2 1:4;8 40mm graded aggregate as in foundation filing complete as as specified and directed.

Pre-cast cement concrete block masonry Type C1 1;3;6 20mm graded aggregate with solid blocks, exc. 10 cm in width and setting in mortar 1:6, complete as as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete as as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc flat rough finished surface complete as as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) of rough finished flat surface complete as as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete as as specified and directed.

M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete as as specified and directed.

M&L TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips for stirrups, spacers and binders

M&L 75 mm thick PCC type C-2 (1:3:6) (using 40 mm graded crushed stone aggregate as in plinth protection laid in panels finished even and smoth without using extra cement.

Material & Labour for Non Skid ceramic coloured tiles 7 to 8 mm thick (Square/ rectangular) area of each tiles exceeding 0.18 Sqm but not exc 0.38 Sqm set and jointed in neat cement slurry and pointed by matching cement in floor complete as specified and directed

Removing excavated materials soft/ disintegrated rock to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

Material & Labour for RCC (Nominal Mix) type B1, 1:2:4 (using 20 mm graded aggr) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete as as specified and directed.

Material & Labour for RCC (Nominal Mix) type B1, 1:2:4 (using 20 mm graded aggr) lintels/roof beams complete as as specified and directed.

Material & Labour for RCC (Nominal Mix) 1:2:4 type B1using 20 mm graded stone aggregate as in foundations, including rafts, footings foundation beams, plinth beams, bases for columns etc basement slabs, under-ramed piles and mass concrete complete as as specified and directed.

Material & Labour for RCC (Nominal Mix) type B1, 1:2:4 (using 20 mm graded aggr) columns,pillars,piers,posts etc complete as as specified and directed.

Material & Labour rendering 15 mm thick cement plaster C M 1:6 on fair faces of concrete or brick surfaces to finished with smooth and even without using extra lime or cement complete as as specified and directed.

Material & Labour for providing two coats of oil-bound distemper over a coat of alkali-resistand primer on old plastered surfaces including necessary preparation to surfaces complete all as specified and as directed

Material & Labour rendering (10+5) mm thick on brick or concrete surface in cement plaster C M 1:4 using WPC on fair faces of concrete or brick surfaces to finished with smooth and even without using extra lime or cement. Note Water Proofing Compound will be measured sepaterly complete as as specified and directed.

Material & Labour rendering 15 mm thick in 1:4 on fair face of brick work or concrete surface even and smooth without using extra cement

S&F mild steel tmt bar 5mm dia and over upto & including 10mm dia in stirup, spacer and binder cut to length bent to shape all as specified and directed

Material & Labour for RCC (normal mix) type B1, 1:2:4 (using 20mm graded aggregate) in chajjas

Material and Labour two coats of acrylic emulsion exterior paint (anti fungal painting-APEX) over one coat of pimer on new plastered surface complete as as specified and directed.

Material & Labour rendering 5mm thick cement plaster 1:3 on ceiling to be finished even and smooth without using extra cement or lime complete as as specified and directed.

Material & Labour 03 coats of white wash on newly plastered surfaces including preparation the surfaces ofn ceiling complete as as specified and directed.

Material & Labour Hardcore (broken stone boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete as as specified and directed.

Material & Labour for 75 mm thick PCC type D-2, 1:4:8 (using 40 mm graded aggregate), as in sub base of floor complete as as specified and directed.

Material & Labour for 25 mm thick PCC type B-0, 1:2:4 (using 12.5 mm graded aggregate), as in sub base of floor complete as as specified and directed.

Material & Labour 20mm thick screed bed or bedding layer of cement mortar 1:4 for laying floor finishes complete as as specified and directed.

Material & Labour forMachine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as as specified and directed.

Material &Labour rendering 10mm thick cement plaster C M 1:6 on fair faces of concrete or brick surfaces to finished smooth and even without using extra lime or cement complete as as specified and directed.

Returning, filling in , including, spreading, levelling, watering and well ramming in layers not exc 25cm deep as in soft/ disintegrated rock complete all as specified and directed

Supply & Fixing CPVC 20 mm outer dia pipes SDR 11 including concealing in walls & plain CPVC SDR 11 fittings on walls/ ceilings or laying in floors complete all as specified

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-1 for 1000 ltrs capacity complete as as specified and directed.

Supply & Fixing PVC (SWR) floor trap 63 mm dia , plain with grating including jointing with solvent cement complete as as specified and directed.

Supply & Fixing Tubular towel rail, 20mm dia, D type, 60cm long Brass chromium plated between flanges complete as as specified and directed.

Supply & Fixing Bib taps,long body 15mm dia, chromium plated fancy type, with capstan head handle, screwed down, screwed for CPVC pipe or for brass ferrule and fixed in repairs

Supply & Fixing Stainless steel soap dish standard size heavy

Supply & Fixing Pillar taps, 15mm dia, cast copper alloy, fancy type with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs complete as as specified and directed.

Supply & Fixing PVC connections 15 mm size with PTMT nuts of length 450m fixed in repair complete as as specified and directed.

Supply & Fixing CP stop cock(angle cock), 15mm dia, fancy type with capston heads screwed both ends for iron pipe or for unions complete as as specified and directed.

Supply & Fixing CP health faucets including flexible hose,wall hook complete as as specified and directed.

Returning, filling in , including, spreading, levelling, watering and well ramming in layers not exc 25cm deep as in soil complete all as specified and directed

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white excluding fixing bolts, flushing cistern and flush pipe including 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level ,white, with inlet ball valve, float and handle including brakets complete as as specified and directed.

S&F in repair vitreous china wash basins, size 550x400mm white flat back including cutting for and pinning in ends of brackets or erecting stand including 32mm waste fittings, chromium plated with long screwed shanks & fly-nuts, flange end bedded in red lead cement and other end fixed complete as as specified and directed.

Supply & Fixing Low density polyethylene pipes 40mm dia of pressure rating 6Kgf/cm2 fixed complete to walls, ceilings, or in floors etc complete as as specified and directed.

Supply & Fixing Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete as as specified and directed.

Supply & Fixing 20mm dia Concussive push button taps of cast copper alloy, screwed for iron pipe and fixed complete as as specified and directed.

Supply &Fixing 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors Complete all as specified & directed.

Supply &Fixing 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors Complete all as specified & directed.

Supply &Fixing 75mm PVC (SWR) vent cowl complete all as specified & directed.

Supply & Fixing PVC (SWR) bends any radius all as specified & directed.

Material & Labour for rendering 10 mm thick in cement mortar 1:4 mixed with WPC, on concrete slab roof top surfaces finished finished even and smooth without using extra cement, complete all as specified.(Liquid WPC will be measured seperately) complete as as specified and directed.

Material & Labour for water proofing treatment using 4 mm thick APP modified membrane consisting five layer membrane with features as specified weighing not less than 4.00 Kgs per Sqm laid over a coat of cold applied bituminous primer @ 0.4 Liters per sqm on surface provide, a layer of APP modified membrane by torching applications including sealing the over lap while torching with 100 mm on length side and 100 mm wide side as per manufacturer instructions including joints and changes in direction be curved with cement mortar 1:3 mixed with SBR latex @ 200 ml/bag of cement curved well before laying of membrane all as per manufacturer instructions and provide a finishing coat with solar reflective bitumenous aluminum paint @ 0.1 Kgs per sqm as prescribed by manufacture membrane to the satisfaction of Engineer-in-Charge. Note (i) Irrespective of lap the net covered area will only be measured for payment. (ii) The quoted rate is deemed to be inclusive of primer, APP membrane and SBR Latex. complete as as specified and directed.

Supply only Liquid water proofing compound complete as as specified and directed.

S&F solid PVC door frame of size 50 mmx47mm made out of 5 mm plain coloured PVC sheet reinforced with MS square tube complete all as specified

S&F Factory made solid panel PVC door shutter 30mm thick(style) consisting of rame made out of M.S tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain olour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S fram welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame.

S & F 2nd class hard wood plain solid straight chowkats frames wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified.

S & F 35 mm thick plain framed panelled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces all as specified and directed.

Supplied and fitted 2nd class H/W 35 mm Glazed and skeleton shutters, open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred beads for securing glass, etc. complete as as specified and directed.

M&L preparation of NEW wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over coat of pink primer. complete as as specified and directed.

Supply & Fixing Butt hinges, 100mm long, medium weight, stainless steel.

Supply & Fixing Aluminium, anodised barrel tower bolts 150mm long of extruded section and fixed complete as as specified and directed.

Supply & Fixing aluminium alloy anodised sliding door bolt 250mm long with hasp, staple and fixing clips of sheet, cast or extruded sections and fixing bolts complete as as specified and directed.

S & F Extruded anodised aluminium alloy handles, fabricated type, of 150mm long. complete as as specified and directed.

Supply & Fixing powder coated aluminium sections for doors, windows, ventilators including joining cleat for fixing etc complete all as specified and directed.

Supply & Fixing sheet glass ordinary quality and fixing with rubber beading etc and 4mm thick exc 0.5 sqm in each pane complete as as specified and directed.

S&F aluminium alloy anodised wire mesh of size 1.5 mm x 3 mm mesh 20 Gauge thick complete all as specified and directed by EIC.

Supply & Fix powder coated grill of make DG 104 (6.5mm thick) sections and mesh size 80mm x 60mm (minimum powder coating 50 microns) complete as as specified and directed.

M&L 18 mm thick Prelaminated particle board, interior grade, type-II, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws as in shutters of Cup Boards complete with Wooden beads of size 18mmx6mm around edges and its varnishing / french polishing as directed.and specified.

S&F continuous ( piano) hinges, mild steel , bright finish or electrigalvanised width of flaps (when opened) 30 mm complete all as specified.

S&F 75 mm size Hasp and staple , safety type, Aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws in repairs complete all as specified.

S & F 100 mm long Aluminium handles, cast type (ISI marked) complete as as specified and directed.

M&L 60mm thick interlocking tiles (glossy finish) of M-30 mix laid, jointing and pointed in neat cement slurry over dry sand cushioning 30mm thick and edges shall be secured with PCC 1:2:4 type B-0 complete all as specified and as directed. Note : Sand cushioning shall be measured separately.

S&F RCC pre cast hume pipe type 10 users capacity septic tank,including excavation in soft/disintegrated rock PCC filling for bed etc including RFR and disposal of surplus spoil complete all as specified and as directed.

Supply & Fixing CPVC 25 mm outer dia pipes SDR 11 including concealing in walls & plain CPVC SDR 11 fittings on walls/ ceilings or laying in floors complete all as specified

S&F 20 mm dia ball brass vales,high pressure with polythene float and fly-nut complete, screwed for iron pipe or brass ferrule complete as as specified and directed.

M/L RCC M-20 Nominal mix(using 12.50 mm graded aggregate as in dead weight

M/L Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel')

Supply only metalic floor hardner

M/L for two coat of synthetic enamel paint on steel surface over 10cm in widht or girth not otherwise describer including preparation newly steel surface over a coat of red oxide zinc chrome primer, all as specified and directed.

M/L preparation of new concrete surface and apply two coat of heat resisting paint,not other wise described.

Demolition of un reinforced cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M/L for 40 mm thick PCC in CM (1:2:4) type B-0 (using 12.50 mm graded stone aggregate) as in sub base of floor.

M/L Non - skid joint free Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed of cement mortar (1;4)

M/L Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 thick sceed bed in cement mortar 1:3 complete all as specified and directed.

M/L praparing old plastered old plastered or un-plastered surfaces of wall,plasters,cornices etc by brooming down or steel wire brushing,scrapping down smoke soot,moulds,moos and efflorescent salts and washing down with water including two coats of oil bond distemper all as specified and as directed by Engr-In-Charge.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance not exceeding 50 m and making good surface all as specified and directed.

M & L for plain cement concrete (1:3:6), using 20mm graded crushed stone aggregate as in foundation, filling and mass concrete all as specified.

S&F stainless steel road sign board of 3 mm thick ACP sign board with night glow radium,white radium letters including logo (stainless steel member of size 24mmx24mmx4mm thick and 2 Nos of stainless steel 50mm dia pole for fixing minimum height 150mm from ground level, size of board is 1.25 m x 0.60M sample kept with AGE B/R II office) all as specified and as directed by Engr In Charge.

M & L PCC (1 : 2 : 4) type B0 (12.5mm graded aggregate) Cement concrete on top at junction of wall and sheet as fillets finished smooth.

Taking down cement plastering on brick or stone walls including raking out joints hacking for key scrubbing down with water etc inside shafts all as directed by Engr-in-Charge.

S & F MS hollow sections in posts, rafters, purlins etc fixed with flat iron clamps, fasteners etc.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated,steel sheet, 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,chajjas, with 20cm drop bend to one side edge of the sheet, where required and similar work etc fixed with self tapping screws all as specified and directed by Engineer -in- Charge.

Surface excavation n. exe 30 cm deep and avarageing 15 cm deepand getting out in Hard/dense soil

Grubbing up tree girth exc 200 cm and n exc 250cm trunk including cutting of trunk portion protruding over ground, digging out roots, filling holes and leveling off ground, stacking of serviceable material and removing of unserviceable material to a distance n exc. 50 m and clearing site

M & L Sand filling under floors or in pavings, laid in layers n.exc. 15 cm thick, spread, levelled and rammed including watering and consolidation..

Material and laying china grass for Garden

M & L PCC 1 : 2 : 4 type B1 (using 20 mm graded aggregate) as in coping

Removing excavated soft/disintegrated rock exc 250 m and nexc 500 m deposinting where directed.

M & L for preparation of new plastered surface and apply two coats of cement base paint complete all as specified and directed.

M & L Angle iron 50 x 50 x6 mm and flat iron for post & struts in fencing including cutting tops to shape as directed, drilling holes, nothich for wire etc including all necessary drilling, bolting or reveting, etc conforming to Fe-290 Gde E-165.

M&L for MS screws and bolts (machine made) 11 to 15mm dia, with hexagonal or square heads at one end and screwed the other or screwed both ens each screwed end to be fitted with washers and one hexagonal or square nut, nexc 5cm long.

Supply and fix PVC coated MS galvanised chain link fencing of size 50 x 50mm of any type of standared, rail straining bolts etc including provision of binding wire.

S & F Framed work such as grills, gates, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes and similar work con- forming to Fe.290.Gde-E-165

M&L for one light point or fan point controlled by one switch with cables 1.5 Sqmm copper cable FRLS multistranded unsheathed drawn through & including casing and capping and 1.5 sqmm conductor cable for earth wire including making connection with common earth and earth dolly including pressed steel terminal al boxes concealed in wall with 3 mm thick plastic laminated sheet top cover fixed with brass screw for mounting switches sockets regulator etc all as per directed by Engr-in-Charge.

M&L for point wiring for 5 amp independent point with 1.5 sqmm copper wire & 1.5 sq mm copper wire as earth lead drawn through & including casing and capping of suitable size all as specified and directed by Engr-in-Charge.

Supply & fixing switch piano flush button single pole one way 5 Amps all as specified and directed.

Supply & fixing switch socket combination outlet 2 in 1 5 pin 5 Amps flush type all as specified and directed.

Supply & fixing ceiling rose, surface Bakelite 65x50 mm Two to three terminals all as specified and directed.

Supply & Fixing stepped type electronic fan regulator flush type including removal of old one.

Supply & Fixing sheet metal enclosure DB, 4 way, SPN, double door factory made powder coated including neutral and earth link connector flush fixed in wall complete including dismantling of old one complete all as specified and directed.Make: L&T/C&S/Havells

Supply & Fix MCB 20 Amps, SPN, braking capacity 10KA, C series all as specified and directed. Make: Legrand/C&S/Havells

Supply & Fix MCB 6 to 32 Amps, SP, braking capacity 10KA, C series all as specified and directed. Make: Legrand/C&S/Havells

Supply & Fixing LED Batten 20 Watts, 230 volts,50 Hz. Make: Havells/Wipro/Bajaj

Supply & Fixing LED Batten 10 Watts, 230 volts,50 Hz. Make: Havells/Wipro/Bajaj

Supply & fixing BLDC (Brushless DC motor) ceiling fan 1200mm sweep, 5 star rated (ISI Marked), 230 volts includung connection rod as per existing size of length of GI pipe medium grade including dismantling of old one and depositing in MES store yard as per specified and directed by Engr-in-Charge. Make : Usha/Havells/Bajaj

Supply & fixing exhaust fan 200 mm sweep plastic body, 230 volts including dismantling of old one depositing in MES store yard as per specified and directed by Engr-in-Charge. Make : Usha/Havells/Bajaj

Tara Construction

M/S Kartik Enterprises

M/s Ekta Engineering Works

M/S G.N.POWAR

M/s Gayatri Contruction Co.

M/s. R.S. LAWANDE