PROVN OF CHAIN LINK FENCING AROUND QUARTER GUARD AND KOTE AT THE SIKH LI REGT CENTRE FATEHGARH.

Amount

Excavating post holes in soft/loose soils (or similar holes ) n exc 0.50 Cum each and getting out and returning filling in balance portion (after PCC filling Ref note given below) with boulder and mixed with earth in layers exceeding 25 Cm thick complete all as specified and directed. Note :- (i) The PCC 'for fxing post shall be measured and paid sepeartely under appropriate item of Sch À. (ii) The cost of boulder and earth shall deemed to be included in quoted unit rate by the contractor.

S&F Posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting or riveting etc; half round or other stock section, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

Mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5 cm but n exc 10 cm long and 11 to 15mm dia of neck complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, fixed with chainlink fencing inluding cranking , bending, welding all as required at site complete all as specified and directed.

Supply only chain link fencing of mesh, mild steel galvanised wire including line wires, binding wire fixed to any type of standards, rails, straining bolts, etc complete all as specified & directed.

Fixing only chain link fencing including line wires ,any mesh and any type of standrads rails ,straining bolts etc including provisioning of binding wire complete as directed.

Supply only mild steel in flat,round or square bars in available legth all as complete all as specified and directed.

M&L for preparation new surface of steel surfaces exc 10 cm width or girth ,not other wise described, two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation new surface of steel surfaces n.exc 10 cm width or girth when unconnected with other painting or when painted in a different tint ,not other wise described, two coat of synthetic enamel paint over a coat of red oxide zinc chrome primer.

S&F for GI barbed wire 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm barbs at 75 mm spacing and shall confirming to IS-278-2001 & IS-280-2006 and straining and fixing to any type of standrad rails straining bolts including securing or tying at crosssing with and provision of Galvanized mild steel wire ,staples or steel pins etc as directed.

Excavating in trenches not exceeding 1.50M wide and not exceeding 1.50M depth for foundation etc or for shafts, wells, cess pits, manhole exc not exceeding 10 Sqm on plan and not exceeding 1.50M in depth and getting out in soft loose soil.

Returning filling in including spreeding leveling watering and well ramming in layers n exc 25 CM complete all as specified and directed.

Removing excavated materials n exc 50M and depositing where directed at a level n exc 1.50M above the startig point.

M&L RCC (Nominal mix) 1:2:4 type B1 20mm graded agg as in foundation, footing, bases of coloum, pillars, post etc complete all as specified and directed.

M&L cement concrete type D-2, 1:4:8 (using 40 mm graded stone agg) as in foundation filling and mass concrete etc complete all as specified and as directed by engineer-in-charge.

M&L cement concrete type B-1, 1:2:4 (using 20 mm graded stone agg) as in post, foundation filling and mass concrete etc complete all as specified and as directed by engineer-in-charge.

Use & waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions, footing all as specified.

S&F rolled mild steel section in framed work as in doors or gates of angles or other section with gussset plates ,rails ,braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging ,of grade Fe -290 (E-165) complete all as specifeid and direcetd.

M/S shree traders

M/S WASEEM KHAN CONTRACTOR