SPECIAL REPAIRS OF COOK HOUSE BLDG NO P 308 A and P 309 A OF INF BN NO 2 AND PROVISION OF RAIN SHELTER FOR SENTRY AT TCP II AT BRICHGUNJ MILITARY STATION PORT BLAIR

Amount

Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc or for shafts, wells manholes pier holes etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out Soft / Loose soil complete all as specified and as directed.

Excavating over areas, n exc 1.5 m deep and getting out Hard/Dense Soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing excavated material exc. 5 km but n exc.8 km and depositing where directed

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Filling under floors or in foundations using approved earth including watering, ramming and consolidation complete all as specified and as directed. Note: Thickness after consolidation will be measured for payment.

Material and labour Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 10cm thick, watered and rammed to a true surface

Dismantling plain or corrugated steel sheeting any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed

Taking down cement plaster of any description from wall/ceiling including raking out joints hacking for key, scrubbing down with water etc, complete all as specified and directed.

Taking down chowkats or frames with shutters area n.exc 1.5 Sqm each(without taking off shutters from the frame) all as specified and as directed

All as per Item No.11 here in before but are exc 1.5 Sqm but n.exc 4.00 Sqm

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) all as specified and directed.

Demolition of RCC in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, complete all as specified and as directed by Engineer -in-Charge.

Demolition of precast concrete block walling, built in cement mortar including all quoins, arches, pillars, etc

Material and labour for 100mm thick PCC 1:3:6, Type C2, (Using 40 mm graded stone aggregate), as in plinth protection/Sub base flooring, finishing surface fair and even, in panel joints with mortar, etc., complete all as specified and directed.

Material and labour 100mm thick PCC 1:4:8 Type D-2 using (40mm graded stone aggregate) complete all as specified and directed.

Material and labour for Cement concrete 40mm thick Type B-1, 1:2:4 (20mm graded aggregate) Finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

Material and labour for precast cement concrete solid block masonry with solid blocks using PCC 1:2:4, Type B1 (using 20mm graded stone aggregate), exc. 10cm in width, set in CM 1:6 complete all as specified and as directed.

Material and labour pre-cast cement concrete masonry in PCC 1:3:6 Type C1 using 20mm graded aggregate with solid block, exceeding 10cm in width setting in CM 1:6 complete all as specified and directed.

Material and labour Cement concrete in foundations, filling and mass concrete type D-2 1:4:8 (40mm graded aggregate) complete all as specified and directed.

Material and labour for RCC M-30 (design mix) as in Columns, pillars, piers, posts and struts, complete all as specified and as directed.

Material and labour for RCC M-30 (design mix) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material and labour Reinforced cement concrete (design mix) M-30 grade using 20mm graded aggregate) in Foundations footings, plinth beams, bases for columns, etc and mass concrete

Material and labour Reinforced cement concrete (design mix M-30 grade using 20mm graded aggregate) plinth beams, above top of footings including attached pilasters and buttresses

Use and waste of Form work to flat surfaces of RCC fins, fascia, chjjas and similar items including edges, for fair finished surfaces complete all as specified and as directed by Engineer -in-Charge.

Use and waste Formwork flat or curved to sides of concrete foundations, footings, bases of columns, and plinth beams and similar work vertical or to batter

Use and waste Formwork flat or curved to to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed

Material and labour for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

All as per item No 29 here in before, but 6mm to 8mm dia

Material and labour for removing loose and broken concrete by chiselling /picking etc upto a depth of 10 to 20 mm from floor/roof slab/chajjas and similar structural members cleaning the dismantled portion with wire brushes etc to remove dust, dirt and other foreign particles including necessary scaffolding etc and removal of debris to a distance not exceeding 50m, complete all as specified and as directed by Engineer -in-Charge.

Material and labour for application of high build polymer modified cement mortar (1:2.5) mixed with 3 lit SBR per bag of cement in ceiling surfaces 10 to 20mm thick in two layers surfaces over a coat of bonding agent Nito Bond SBR (1 Ltr SBR + 1 Ltr) water + 3 kg cement), complete all as specified and as directed by Engineer -in-Charge.

Material and labour rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed

Material and labour for 15mm thick external rendering in two layers of 5mm thick in CM 1:4 mixed with water proofing compound (water proofing compound shall be used @3% weight of cement) over a coat of 10mm thick in CM (1:6) over brick or concrete surfaces finished even and fair. Note: Supply only WPC will be measured and paid separately

Supply only integral water proofing compound

Material and labour for rendering 5 mm thick in CM 1:3 finished even and smooth without using extra cement on ceiling including cement slurry 3 kg/sqm complete all as specified and as directed

Material and labour for rendering 15mm thick cement plaster in CM 1:4 on concrete surfaces of roof slab and parapets mixed with WPC @ 3% by weight of cement all as specified and directed by the Engineer-in-Charge. Note: WPC shall be measured and paid separately

Material and labour for two coats of OBD over a coat of primer on newly plastered surfaces of walls including necessary preparation of surfaces all as specified and directed.

Material and labour for two coats of OBD over a coat of primer on newly plastered surfaces of ceiling including necessary preparation of surfaces all as specified and directed.

Material and labour for preparing old decorated surfaces of ceiling and applying two coats of OBD over a coat of primer all as specified and directed.

Material and labour for two coats of OBD over a coat of primer on old plastered surfaces of walls including necessary preparation of surfaces all as specified and directed.

M& L for two coats of weather proof exterior acrylic emulsion paint with anti fungal property over a coat of primer on new plastered wall surfaces including preparation of surfaces complete all as specified and as directed.

M& L for two coat of weather proof exterior acrylic emulsion paint with anti fungal property over a coat of primer on old plastered wall surfaces including preparation of surfaces by complete removal of existing treatment complete all as specified and as directed.

Material and labour for preparation of old steel surface of any description over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

Material and labour Three coats of white wash on internal wall surfaces including preparations complete all as specified and as directed.

Material and labour for Preparation of new or previously untreated steel surfaces & applying a two coats of synthetic enamel paint over a coat of red oxide primer over 10cm in width or girth, not otherwise described.

Supply and fix for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete all as specified and as directed.

Supply and fix for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and as directed.

Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self-tapping screws as specified.

Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self-tapping screws as specified.

Material and labour for water proofing treatment with the following specifications complete all as specified and as per manufacturer’s instructions:- (i) Rendering 10mm thick in CM 1:4 on concrete surfaces mixed with water proofing compound @ 3% by weight of cement as leveling course (ii) Apply a coat of hot blown bitumen 85/25 @ 1.20 kg/sqm over a coat of bituminous primer @ 0.3 ltr per sqm. (iii) Laying APP membrane (STP Aquashield or equivalent) weighing not less than 3.5Kg/sqm, reinforced with polyster non woven fabric (weighing not less than 150 gms/sqm) with 100mm over laps both longitudinally and transversally and overlaps shall be sealed by torch, membrane shall be taken to the parapet through fillet and shall be tucked in inside after a height of 300 mm. (iv) Apply one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm over the membrane. Note:- Water proofing compound shall be measured and paid separately)

Material and Labour for tensile membrane min 700 GSM for roof covering all as specified and as directed by Engg-in-Charge

Supply and fix as in repairs aluminium anodised snap grid frame work (size of grid 605x605mm) with 35x25x1.5mm main tee and 25x25x1.4mm, cross tee and wall angle for false ceiling and suspended with 6mm dia GI wire, hooked to roof with needful adjustment up to 1200mm long by means of ceiling cleats made out of GI Flat 40 X 3mm 60mm long and expansion hold fasteners 12.5mm dia 40mm long, including dismantling celling board of any description and any type fixed to the aluminium frame work with screws or nails etc complete all as specified and as directed by Engineer -in-Charge.

Fixing only in repairs Eco board 600 X 600 X 4mm thick decorative type fixed to the aluminium frame work with screws or nails etc including two coats of oil bound distemper over a coat of primer complete all as specified and as directed by Engineer -in-Charge. Note :- Fair Eco Boards obtained from item No.53 to be re-used

Supply and fix in repair Eco board 600 X 600 X 4mm thick decorative type fixed to the aluminium frame work with screws or nails etc including two coats of oil bound distemper over a coat of primer complete all as specified and as directed by Engineer -in-Charge.

Supply and fix coloured joint free non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors etc. set, jointed and pointed in white or coloured cement to match over screed bed in cement mortar 1:6, 20 mm thick, all as specified and directed.

Supply and fix coloured glazed ceramic tiles 300mm x 200mm x 5.5mm to 6mm thick on vertical surfaces such as skirting & dados etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with surfaces etc including backing coat of 10mm thick CM 1:3 all as specified and directed.

Material and labour for machine cut kota stone slab 20 to 25mm thick in treads of steps in stair laid and jointed with white cement slurry mixed with pigments to match the shade of the slab incl rubbing and mirror polishing laid over cement screed bed in cement mortar 1:4, 20mm thick, complete all as directed

Material and labour for machine cut kota stone slab 20 to 25mm thick in rise of steps, skirting, dado and pillar as in vertical surfaces laid and jointed with white cement slurry mixed with pigments to match the shade of the slab incl rubbing and polishing laid over cement screed bed in cement mortar 1:3, 10mm thick, complete all as directed

Material and labour for granite slab 20 mm thick table rubbed and polished as in cooking platforms, steps, jambs, pillars and the like including pointing with white cement 1:2 using marble dust with admixture of pigment to match the shade of granite stone including cutting and polishing over and including 20mm thick cement mortar bedding layer 1:4 complete all as specified and as directed by Engineer-in-charge

Material and labour for granite slab 20 mm thick of any type of work table rubbed and polished for wall lining (veneering to wall) bedded 10mm thick ,in cement mortar 1:3 and pointing with white cement 1:2 using marble dust with admixture of pigment to match the shade of granite stone complete all as specified and as directed by Engineer-in-charge

Material & labour for designer coloured chequered cement concrete tiles of size 20cm x 20cm x 25mm with jointed and pointed in neat cement slurry with grey cement and pigment to match the shade including screed bed 20mm in CM (1:4) all as specified and directed.

Material and labour for 3 to 4 mm thick 38 mm deep glass dividing strips as specified to be provided between the floor panels not exc size 2m grid. The glass dividing strips shall be ground smooth with stone and shall be laid flush with the floor level.

Supply and fix Aluminium anodised (minimum anodisation is 15 microns) Door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars, standard aluminium grills, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, locking arrangement etc, complete with standard aluminium sections, all as specified and as directed by Engineer-in-charge.(Aluminium section shall be of make Jindal/Hindalco/ Indalco). (Note:- Weight of various Aluminium sections shall only be considered for measurement for payment. However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle boards, aluminium wire cloth as applicable will be measured and paid separately as supplied only).

Supply only 12 mm thick Prelaminatd particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination and fixed to aluminium frames complete all as specified and as directed by Engineer -in-Charge.

Supply only 4mm thick sheet glass ordinary quality and glazing with rubber packing around the glass, in squares n. exc 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-charge.

Supply only 4mm thick figured glass ordinary quality and glazing with rubber packing around the glass, in squares n. exc 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-charge.

Supply only aluminium alloy wire mesh 0.45mm nominal dia of wire and average width of aperture 1.4mm fixed with aluminium wire staples etc. complete all as specified and as directed by Engineer-in-charge.

Supply and fix solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing in SSR complete all as specified and directed by Engineer -in-Charge.

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC `C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing in SSR complete all as specified and directed by Engineer -in-Charge.

Supply and fix in repairs 75mm Size Butt hinges type C-21 , extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed

Supply and fix in repairs 100mm Size Butt hinges type B-21 , extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed

Supply and fix in repairs 200 mm long Aluminium, anodised, barrel tower bolts of extruded section.

Supply and fix in repairs 150 mm long Aluminium, anodised, barrel tower bolts of extruded section.

Supply and fix in repairs 100 mm long Aluminium, anodised, barrel tower bolts of extruded section.

Supply and fix in repairs Aluminium alloy, anodised, sliding door bolt 300mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

Supply and fix in repairs 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised.

Supply and fix in repairs100 mm long Extruded Aluminium alloy handles, fabricated type, anodised.

Supply & Fix in repairs 140mm long door stopper of aluminium alloy body and tounge, anodised with hard drawn steel spring fixed in floor complete all as specified and as directed by Engineer -in-Charge.

Supply and fix PVC flushing cistern 10 litres capacity syphonic action type, low level, white with inlet, ball valve, float, handle and flush pipe, etc complete all as specified and directed.

Supply and fix in repairs Brass Chromium plated shower rose 125mm size, with swivel joint, fixing to steel pipe or union, complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs Bib tap cast copper alloy chromium plated, 15 mm dia with crutch or butter-fly handle, screwed down, screwed for iron pipe or for brass ferrule etc all as specified and directed.

Supply and fix in repairs angular stop cock, cast copper alloy chromium plated, 15 mm dia screwed down high pressure, screwed both ends for iron pipe or for unions complete all as specified and as directed by Engineer-in-Charge.

All as per item No 83 here in before, but fancy type, chromium plated with long shank and cup (concealed type) screwed both ends for iron pipe or for unions complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs fancy type, Pillar taps , cast copper alloy , with capstan heads , chromium plated , screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15 mm and fixed in repairs, all as specified.

Supply and fix in repairs kitchen sinks with drainage boards, ISI marked [As per IS 13983- 1994] made of stainless steel of AISI 304 grade 18/8 qualilty, 1mm thick with plugs, washers & wastes, including in cement mortar 1:3 to dwarf wall or incl fixing cantilever brackets and connecting union to pipes overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed by Engr in Charge.

Supply and fix in repair vitreous china wash hand basin white flat back size 630x450mm incl brackets, PTMT coupling, 32 mm GI pipe waste pipe complete all as specified.

Supply and fix in repairs brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

Supply and fix in repairs stainless steel gratings 125mm dia, complete all as specified and as directed by Engineer-in-Charge

Supply and fix PVC connection both end brass union 15 mm dia & check nuts of length 450 mm long.

Supply and fix in repairs vitreous china squatting pan, Orissa pattern size 630X450 mm white with integral foot rest (excluding flushing cistern) including 'P' or 'S' trap etc complete all as directed.

Supply and fix in repair 20mm dia Gun metal globe or gate valve with iron wheel head, screwed both end for iron pipe.

Supply and fix for 25mm dia ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule .

Taking up or down 20mm dia bore steel tubing galvanised and connections complete all as specified and directed.

Taking up or down 15mm dia bore steel tubing galvanised and connections complete all as specified and directed.

Supply and laying 20mm external dia UPVC pipes SDR11 including Plain UPVC fittings SDR11 mean fittings which do not have any metal component and is jointed with UPVC solvent cement only (Elbow, Tee, Socket, Reducer, Bushing, Step over bends, End cap, End plugs, etc) & Special fittings include CPVC Brass fittings (Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor, etc), Unions, Ball valves, Flange and tank adaptor as on walls/ceiling/floors complete all as specified and as directed by Engineer-in-charge.

All as per item No 97 here in before but 25mm dia

Dismantling of CI drain pipes,50-100 mm dia jointed in cement mortar including all fittings joints etc complete all as specified and directed.

Material and labour for PVC (SWR) pipes 110mm bore double socketed in any length with rubber ring joints, fixed to wall incl testing of pipe etc complete all as specified and directed by Engr-in-Charge

All as per item No 100 here in before but 75mm bore of pipe all as specified and directed.

Disconnecting of existing tank of capacity 500 ltr and setting aside or lowering if required for repairs cleaning etc and refixing in position hoisting and connecting after repair work, complete all as specified and as directed by Engineer -in-Charge.

Supply and fix rotational moulded polythelene water storage tanks ISI marked (cylindrical vertical with closed top) of 500 Ltrs capacity with tank cover (top), hoisted and fixed in position, including taking down existing with all connections complete all as specified and as directed by Engineer -in-Charge.

Material and labour for PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm outer dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed by Engineer -in-Charge.

Supply and fix PVC (SWR) bends 110mm bore with oval access doors all as specified and directed.

Supply and fix PVC (SWR) bends 75mm bore with oval access doors all as specified and directed.

Supply and fix PVC (SWR) junction single, (Single T) 110mm bore, equal or unequal with oval access doors all as specified and directed.

All as per item No 107 here in before but 75mm bore of pipe all as specified and directed.

Supply and fix PVC (SWR) branch piece, single (single Y) equal or unequal110mm bore, equal or unequal with oval access doors all as specified and directed.

All as per item 109 here in above but 75mm bore of pipe all as specified and directed.

Taking down carefully, copper/aluminium point wiring (Light, fan, scoket or power) complete, including fittings and fixtures such as switches, ceiling roses, regulators, sockets etc., and making good disturbed surfaces of walls floors, etc., complete all as specified and as directed by Engineer-in-Charge.

Material and labour Point wiring complete with 1.5 sqmm single core FRLS PVC insulated and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC casing and caping and all accessories fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover/ Pre moulded PVC switch board for housing the switches, socket outlets, fan regulators etc., all as specified and as directed for the following: - One light point/Exhaust fan point controlled by one switch

All as per item No 112 here in before One fan point controlled by one switch and one regulator

All as per item No 112 here in before One 3 pin switch socket outlet point 5 amps on same board with other switches.

All as per item No 112 here in before before One 3 pin switch socket outlet point 5 amps on independent board.

All as per item at sl No.112 here in before but with copper conductor cable for one 3 pin socket outlet, 15 amps independent, with cable 4 Sqmm size and 4 Sqmm earth continuity conductor, complete all as specified and as directed by Engineer-in-Charge.

Material and labour for point wiring complete with single core multi stranded Copper conductor FRLS cable of size 1.5 sqmm PVC insulated unsheathed 1100 volt grade in and including PVC conduit suitable size including Tee junction bends etc concealed in wall/fixed on ceiling and PVC switch board hylam sheet of 3mm thick including M.S. sunken boards of suitable size for housing switched sockets etc including 1.5 sqmm. green PVC insulated wire for earth continuity. including Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills sunshades, shelves, lintels, etc.; and cutting chases for concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall. complete all as specified and as directed by Engineer-in-Charge One light point/Exhaust fan point controlled by one switch

All as per item No 117 here in before One fan point controlled by one switch and one regulator

All as per item No 117 here in before One 3 pin switch socket outlet point 5 amps on independent board.

Supply and fix switch piano flush type single pole one way 5 amps, complete all as specified and as directed by Engineer-in-Charge

Supply and fix switch socket outlet 3 & 2 pin (mult pin) 5 amps flush/box type, complete all as specified and as dircted by Engineer-in-Charge

Supply and fix switch socket outlet, 2 in 1, 3 pin 15 and 5 amps, controlled by one switch flush/box type complete all as specified and as directed by Engineer-in-Charge.

Supply and fix ceiling rose surface baklite 65 x 50 mm 3 terminal, complete all as specified and as directed by Engineer-in-Charge

Supply and fix lamp holder(angle type) PVC body with back plate suitable for batten fittings, complete all as specified and as directed Engineer-in-Charge

Supply and fix fan speed regulator, electronic suitable for single phase AC, 240 volts, 50 Hz,100 watts, complete all as specified and as directed by Engineer-in-Charge Make:-Anchor/Havells/Bajaj

Taking down and refixing ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and as directed.

Taking down and refixing old serviceable exhaust fan and connecting up including providing of cable from ceiling rose/connector to fan complete all as specified and as directed.

Taking down and refixing 4 feet Box type fitting including accessories and connecting the twin core cable to existing ceiling rose all specified & directed .

Supply and fix sheet metal enclosures Loadline distribution board TPN, 4 ways 415 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs and in and including 63A MCCB as incoming complete all as specified and as directed including taking down old MCB DBs complete. Make: Havells/Legrand/C&S

Supply and fix in repair metal enclosure distribution board SPN, 8 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs, including taking down old MCB/DB, complete all as as specified and as directed.

Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, all as specified and as directed. Make : Havells or equivalent Legrand/L&T/Schneider

Supply and fix MCB SPN 240 volts, 5 to 32 Amps, all as specified and as directed. Make : Havells or equivalent Legrand/L&T/Schneider

Supply and fix metal enclosure distribution board SPN, 2 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs, Complete all as specified and as directed by Engineer-in-Charge Make :Legrand/C&S/L&T Note:- Incoming & Outgoing connections from the DB shall be provided with proper lugs/thimbles etc...

Supply and fix in repair MCB SPN, 240 volts, 6 to 32 amps C series complete all as specified and as directed by Engineer-in-Charge Make : Legrand/Schneider/L&T

Material and labour for sub main wiring complete with two runs of 6 Sqmm FRLS single core PVC insulated in sheathed single core cable 1100 volts grade, multistranded with copper conductor (ISI Marked) drawn through and including PVC Casing and caping and all accessories fixed to wall/ roofs/ floors etc with one run of 6.0 sqmmm FRLS single core multistranded copper conductor as earth continuity conductor, including dismantling unserviceable sub main wiring including accessories, complete all as specified and as directed by Engineer-in-Charge. Note : (1) Two runs of cable one run of conduit & one run of earth continuity conductor shall be measured as one running metre.

Supply and fix Recess mounted LED Ultra slim 15 w Round type with in die cast aluminium housing finished in premium white powder coating prewired upto connection block and connecting with three core PVC copper flexible cable of size 1.5 Sq.mm from ceiling rose to connector block, including taking down old unserviceable fitting of any wattage, complete all as specified and directed by Engineer-in-Charge. Make - Philips model no 59523 or Equivalent in Bajaj/Crompton

Supply & fix in repair LED holder type non dimmable bulb 10 watt complete all as specified and as directed by Engineer-in-Charge. Make: Havells Cat No.LHLDERUEMD8X010 or Equivalent in Wipro/C&S/Havells.

Supply and fix 25 W New generation energy saving & environmental friendly long life versatile pressure dia cast aluminium IP65 road way luminaire with high power LEDs as light and electronic driver complete with necessary brackets (made out of 25 mm bore GI light grade pipe approx. 0.6 M long) nuts, bolts etc to be fixed as on walls complete as directed. Make: Philips cat No BRP020 LED HP/CW 240V 25Wor equivalent model of Bajaj/Wipro / CG

Supply and fixing energy efficient LED Smart bright batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours including lamp and connecting with twin core sheathed cable from fitting to ceiling rose all as specified and as directed. Make : Philips Cat No BN021C LED20S PSU CDL/NW GR or eqvt in make of Bajaj/Wipro.

Supply, lay, test and commissioning underground XLPE insulated and PVC sheathed, armoured heavy duty underground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 2 Core 6 sq mm all specifed and directed

Supply, lay, test and commissioning underground XLPE insulated and PVC sheathed, armoured heavy duty UG cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminium stranded conductor 1100 volt grade of cross section area 3.5 Core 25 sq mm all specifed and directed

Supply and lay cable protection pipe of HDPE double wall corrugated (DWC) including couplers, bends etc of size 50mm OD and ID 38 mm confirming to IS 14930 -II and ISI Marked complete all specifed and as directed

Material and labour for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I complete all specifed and as directed

Cutting bituminous road at a width not more than 30cm and a depth not exceeding 60 cm for laying of pipes on road crossing for cable protection and making good with the existing surfaces complete all as specified and as directed by Engineer-in-charge.

Supply & laying GI tubing light grade of size 50 mm bore for encasing LT / HT cable for mechanical protection laid under floor/roads or fixed on wall/pole/MS channels etc complete with nuts bolts clamps including taking out old one complete all specifed and as directed

Gulmarg Electrical Service

T.THIYAGARAJAN

Priya construction

Ravi Enterprises

M/S AMK CONSTRUCTIONS

SK CONSTRUCTION

SARKAR WOOD FURNITURE SHOP