SPECIAL REPAIR TO BLDG NO SCD-86, BCD-100, BCD-106, P-41 (MT), ET-06 AND ET-44 OF ASC CENTRE AND COLLEGE UNDER GE (CENTRAL) BANGALORE

Amount

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles all as specified & directed.

Taking down cement plaster on brick or stone walls etc, including raking out joints, hacking for key, scrubbing down with water, etc. all as specified & directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground GL) as in plinth protection/ hard standing/ floors/ path etc all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing derviceable tiles to store and rubbish of the premises all as specified & directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frame) area exc 1.5 sqm but n.exc 4 Sqm including making good the disturbed surfaces to match with adjoining surfaces all as specified & directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frame) area not exc 1.5 sqm including making good the disturbed surfaces to match with adjoining surfaces all as specified & directed.

M&L for Pre-cast cement concrete (1:3:6) type C-1 using 20 mm graded crushed stone aggregate as in solid block masonry exc 10 cm in width and setting in cement mortar (1:6) complete all as specified & directed.

M&L for Pre-cast cement concrete (1:3:6) type C-1 using 20 mm graded crushed stone aggregate as in solid block masonry not exc 10 cm in width and setting in cement mortar (1:4) complete all as specified & directed.

M&L for Rendering 15 mm thick cement mortar (1:4) on fair faces of brick work or concrete wall surfaces finished even and smooth without using extra cement including mixing with water proofing compound complete all as specified & directed. (Note : water proofing compound will be measured & paid separately).

M&L for Rendering 15 mm thick cement mortar (1:6) on fair faces of brick work or concrete wall surfaces finished even and smooth without using extra cement all as specified & directed.

Supply only integral waterproofing compound, ISI marked,of approved make complete all as specified & directed.

M&L for Plain Cement Concrete (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregate as in 25 mm thick sub base of floors all as specified & directed.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick, area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over & including screed bed 15 mm thick CM (1:6) all as specified & directed

M&L for Vitrified Ceramic tiles Dark shade 10mm thick (square/rectangular) polished, area of each tiles not exc 0.36 Sqm in floor etc,set and jointed in neat cement sluryy and pointed in coloured cement to match over & including screed bed 15mm thick in CM (1:6) all as specified & directed

M&L for Vitrified Ceramic tiles Dark shade 10mm thick (square/rectangular) polished area of each tiles not exceeding 0.36 Sqm as in Vertical Surface/Dado/Skirting etc set and jointed in neat cement slury and pointed in coloured cement to match over & including backing Coat 10mm thick CM (1:4) all as specified & directed

M&L for Glazed ceramic coloured tiles 350x250x7mm / 450x350x7mm thick on vertical surfaces such as dados and risers to step etc, set and jointed in neat cement slurry and pointed in coloured cement to match the tiles over & including backing coat 10mm thick CM (1:4) all as specified and as directed.

S&F Factory made uPVC door frame made of uPVC extruded sections having an overall dimension extruded section profile 48 x 40 mm ( tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanised M.S. tube of size 19 x 19 mm and 1 mm ( ± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified & directed

S&F Factory made UPVC white colour sliding window/ventilators three track made of extruded profile with wall thickness of 2.3mm(+-0.2mm) window profile with hollow section with multi chamber. Frame (88mmx52mm), sliding sash (42mmx67mm) sliding mesh sash (42mmx57mm) Sliding interlock(one vertical length in each shutter) (45.5mmx28mm) glazing beads (24.5mmx16mm) will be mitred cut and fusion welded at all corners incl drilling of holes for fixing hard ware and drainage of water etc making arrengements for fixing of hardware EPDM gasket 1.2+- .2mm thick galvanised steel frame (30mmx18mm) 2 Nos, sliding mesh sash (26mmx10mm) profile to be inserted in required profile frame will be fixed to the wall with 8mmx100mm long fastners Hardware : tough lock of zinc alloyed (white powder coated) steel roller system stailess steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories area n.exc 2 sqm each all as specified & directed. (Note: (i) unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. (ii) Net opening will be measured for payment purpose.)

S&F Sheet glass 5.5mm thick, ordinary quality in square/rectangular in each pane exc 0.5sqm all as specified and as directed.

S&F Figured glass 5mm thick, pin head type in square/rectangular in each pane not exc 0.5sqm all as specified and as directed.

S & F Sheet glass obscured or frosted on one side, 5.5 mm thick and glazing with upvc beading in square/rectangular not exc 0.50 sqm in each panes all as specified and as directed.

S & F Rotational moulded polythene water storage tank 1000 litres capacity (white colour) (cylindrical vertical with close top) triple layered colour white both inside and outside with top cover including PVC float valve high pressure suitable for 25 mm bore pipe with polythene float, fixture hoisted and fixed in position, making necessary connection including dismantling of existing any type & any capacity water storage tank complete all as specified & directed.

Taking up or down steel tubing galvanised 25mm dia with fittings or any other type of pipe and removing complete all as specified & directed.

Taking up or down steel tubing galvanised 20mm dia with fittings or any other type of pipe and removing complete all as specified & directed.

S&F CPVC Pipe 25 mm outer dia (ISI Marked) SDR II & plain CPVC SDR II fittings fixed on wall, celing or floors complete all as specified & directed.

S&F CPVC Pipe 20 mm outer dia (ISI Marked) SDR II & plain CPVC SDR II fittings fixed on wall, celing or floors complete all as specified & directed.

S & F in repairs Health faucet (ABS) chromium plated with 1 metre long flexible M S pipe chromium plated, suitable for 15mm bore pipe complete all as specified and directed.

S & F in repair Bib cock 2 way, double handle with flange, cast copper alloy chromium plated, screwed down, suitable for 15mm bore iron pipe all as specified and directed.

S&F in repair Stop valves / angle valve, cast copper alloy chromium plated fancy type with long shank and cup, screwed down to iron pipe 15 mm dia bore complete all as specified and directed

S&F in repairs Unbreakable corner Glass (5.5mm thick) shelf 8" semi circular with 2 Nos of SS rail complete all as specified and directed

S & F in repairs stainless steel towel Rack 600mm long with lower hanger complete all as specified.

S&F PVC mirror cabinet suitable Bathroom, best quality of approximate size 430X330mm fixed to wall using brass screws complete all as specified and directed.

S & F in repairs brass, chromium plated, 15mm bore wall mixer for mixing hot and cold water, screwed down with provision of over head shower and cock for iron pipe 15mm dia and fixed complete all as specified and directed.

S & F in repairs Integrated European type Water Closer (EWC), rimless pedestal pattern, coloured, P trap/ S trap with dual type flushing Cistern, with soft closing seat cover, all as specified and directed.

S&F in repair Vitreous China Wash hand basin, white flat back size 550x400 mm including following accessories complete all as specified & directed :- (i) Pair of mild steel angle iron brackets duly painted & erected/embeded in wall including cutting hole and pinning in ends making good disturbed portion using cement mortar (1:3) (ii) Pillar taps, brass, with capston heads, fancy type, chromium plated (iii) Waste coupling brass chromium plated 32 mm dia suitable for wash hand basin & 32 mm dia LDPE PVC waste pipe (iv) PVC connection 15 mm dia 450 mm long with PTMT nuts

Supply and fixing in repair Bib tap cast copper alloy with crutch or butter fly handle screwed down screwed for Iron Pipe 15mm dia or brass ferrule and fixed all as specified and directed.

S&F in repairs Stainless steel tubular towel rail, 20mm dia ‘D’ type, 60CM long between flanges all as specified and directed.

S&F in repairs Soap dish 150mm size, brass chromium plated fixed to wall with chromium plated brass screws complete all as specified & directed.

S&F Toilet Pepar holder with flat recessed type, stainless steel complete all as specified & directed.

M&L for PVC (SWR) floor trap, 75mm dia outlet, plain with grating including jointing with solvent cement etc complete, fixed in repair complete all as specified & directed.

S&F in repair PVC (SWR) pipes 110mm dia bore, single socketed in any length with rubber joints, fixed to walls etc complete.

S&F in repair 75mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls etc complete all as specified & directed.

S&F PVC (SWR) bends 110mm dia any radius all as specified & directed.

S&F PVC (SWR) bends 75 mm dia any radius all as specified & directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & fixed all as specified & directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site all as specified & directed.

S&F Butt hinges 100mm mild steel cold rolled, medium weight all as specified & directed.

S&F Aluminium anodized barrel tower bolts of extruded section, 200mm long all as specified & directed.

S&F Aluminium anodized handles of extruded section 150mm size all as specified & directed.

S&F in repair Curtain rod, stainless steel decorative type 25mm dia all as specified & directed.

S&F in repair stainless steel brackets suitable for decorative type curtain rod all as specified & directed.

M&L for Cement concrete (1:2:4) type B1 using 20mm gradded aggregate as in kerbs / copings etc, including necessary formwork, rounded or chamfered on edges complete all as specified & directed.

M&L for Preparing of wood and wood based surfaces of new or old, of any description and girth, not otherwise described and treated with cresote oil complete all as specified and directed.

S&F MDF Board 19 mm thick, both side finished, cut to size & fixed in wardrobes, number of compartments & drawers as ordred complete all as specified & directed.

S&F in repair Ball catches with 8mm dia steel ball, and brass body and striking plate, fixed complete all as directed.

S&F Continuous (Piano) hinges mild steel bright finish or electrogalvanised, 40mm flaps width (when open) all as specified & directed.

S&F Stainless steel Peg set fixed to wall with brass screws all as specified & directed.

S & F in repairs shower rose with 190mm arm, brass chromium plated with swivel joints, 100mm dia including fixing to iron pipe 15mm dia complete all as specified and directed.

M&L for Preparation of newly plastered surfaces of wall and applying two coats of distemper acrylic emulsion over a coat of alkali resitant primer on 1mm thick wall care putty finished to smooth surfaces complete all as specified & directed.

M&L for Complete removal of existing treatment of old plastered surfaces of wall and applying two coats of distemper acrylic emulsion over a coat of alkali resitant primer on 1mm thick wall care putty finished to smooth surfaces complete all as specified & directed.

M & L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new or old surfaces complete all as specified & directed.

M & L for Complete removal of existing treatment and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resisitance as per IS 15489:2004, alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new or old surfaces complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F Mild steel framed work such as grills, gratings,etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways,railings,framework of water tanks and similar works conforming to Fe290 Gde-E-165 fixing complete all as specified and directed.

M&L for Preparation of new or previously untreated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enemel paint over a coat of red oxide primer complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 using 20mm graded aggregate as in plinth protection, finished even and smooth without using extra cement including joints filling and sealed with sealing compound Grade ‘A’ etc complete all as specified & directed.

M & L for Rendering 15 mm thick cement mortar (1:6) on stone masonry surface of walls finished even and smooth without using extra cement complete all as specified & directed.

M&L for Rendering 15 mm thick cement mortar (1:4) on stone masonry or brick masonry or surface other than fair face of brick-work of walls finished even and surface without using extra cement all as specified & directed.

M&L for Rendering 5mm thick cement mortar (1:3) on fair faces of concrete ceiling surface finished even and smooth without using extra cement all as specified & directed.

Demolition of stone slabs of any description or thickness in floors laid bedded and pointed in any mortar etc. complete removal of debris all as specified & directed.

M&L Coloured Non-Skid Ceramic joint free of matt finish tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor etc,set and jointed in neat cement sluryy and pointed in coloured cement to match as in floor over & including 15mm thick screed bed in CM (1:6) all as specified & directed.

Supply & fixing Figured glass 4mm thick, not exc 0.5sqm each pane glazing with oil putty complete all as specified & directed.

S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with aluminium wire staples with wodden beading on wooden shutter or with screws to steel / aluminium shutter all as specified & directed.

M & L for Cutting holes in stone/brick walls built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete (1:2:4) type B1 exceeding half brick but not exceeding one brick all as specified and as directed.

S&F Mild steel work as in band, strap, hold fast, cleat, hook, hinges, base tie for foor frame, support or stay for rain water pipe, guard bars etc and other similar items conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S&F Butt hinges 75mm size mild steel cold rolled, medium weight all as specified and as directed.

S&F Aluminium, anodized barrel tower bolts 150mm long, extruded section all as specified and as directed.

S&F Aluminium anodized handles 100mm long, extruded section all as specified and as directed.

S&F Aluminium alloy, anodized, sliding door bolts 300mm long with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and as directed.

S&F in repairs Vitreous China Wash Hand Basin of size 550 X 400 mm with pedestal Ivory colour 1105mm height including 32mm dia Brass Chromium Plated Waste Fitting and PVC connection pipe of 15mm dia 600mm long with PTMT nuts including suitable fixing arrangement, cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 complete all as specified and as directed.

S&F in repairs Vitreous china squatting Pan 'Orrisa' Pattern size 580 x 440 mm white with integral foot rest, P or S Trap, lime concrete bedding making good the disturb surfaces all as specified & directed.

S & F in repair Vitreous china urinals bowl, half stall size 580x380 x 350 mm min white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing pipe all as specified & directed.

S&F in repairs PVC Low level flushing cistern 10 ltr capacity,PVC valveless, syphonic action type, low level, white, with inlet, ball valve, float and including 32mm dia PVC flush pipe, etc complete all as specified & directed.

Dismantling Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating, 150 AZ, G I based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating, 150 AZ, G I based plain sheet steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Powder coated aluminium window and ventilator shutter, side hung type or sliding type, without sash bar, aluminium sections weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type B-21 100mm long(2 no) suitable handle (1 no) complete all as specified & directed

S&F Aluminium powder coated (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified & directed.

S&F in repairs Bib taps chromium plated fancy type cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe 15mm dia or for union complete all as specified & directed.

M&L for Preparation of newly plastered ceiling surface and applying three coats of white wash complete all as specified & directed.

M&L for Preparation of newly plastered wall Surfaces and applying two Coats of cement base paint over a coat of self primer complete all as specified and as directed.

S&F PVC (SWR) bends 110mm dia any radius with access door complete all as specified and as directed.

S&F PVC (SWR) bends 75 mm dia any radius with access door complete all as specified and as directed.

S&F PVC (SWR)vent cowl 110mm bore complete all as specified and as directed.

S&F in repairs Stainless Steel Grating of 125mm dia with or without Waste Hole complete all as specified and as directed.

S & F in repairs PVC connection 15mm dia pipe with PTMT nuts, 600mm long complete all as specified and as directed.

Dismantling boarding any description fixed in any position with nails complete all as specified and as directed.

Dismantling unframed timber scantling 40 sq cm and over in section in any position complete all as specified and as directed.

Dismantling of battens for tiles, sheets, shingles etc, of any size including tilting fillets in section in any position spaced not exc 15 cm all as specified and as directed.

Dismantling of wall and ceiling board fibre pulp, insulation etc or insulation boards/ clabs blankets any thickness incl cover fillets all as specified and as directed.

S & F second class hard wood 20mm thick boarding clean sawn with butt joints planed on one side fixed with nails in any situation as in weather boarding all as specified and as directed.

All as per serial item No 103 herein after but fixing only -ditto-

M&L for Second class hard wood, clean sawn as in scantling framed and fixed to walls with screws etc complete all as specified and directed..

M&L for second class hard wood clean sawn battens at 30 cm centers sectional area exc 5 Sq cm but n.exc 15 sq cm etc complete all as specified and directed..

M&L for Sadherhali stone slab 18-20mm thick as in flooring, steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of slab over & including screed bed 15 mm thick CM (1:4) and Rounding to edges, polishing complete all as specified and directed..

M&L for Sadherhali stone slab 18-20mm thick for skirting, riser, dado and like jointing in cm (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of slab over & including backing coat 10 mm thick CM (1:3) all as specified and directed..

S & F for Non Asbestos fibre cement building boards 4 mm thick of size 600x600mm fixed or laid / inserted to timber / GI Aluminium frame work ( White colour) over and including Aluminium snap grid size 600x600 mm duly suspended 6 mm dia GI hangers 1200mm length adjusting level fixed to roof slab or purlins by means of ceiling cleats made out GI flat 40x3mm size 60mm long and expension holdfasteners 12.5mm dia 40mm long complete all as specified & directed.

S&F Powder coated aluminium sliding window, three track, frame & two glazed shutter and one wiremesh shutter with following specification all as specified & directed :- (i) Aluminium frame section 116x36.50x1.80mm. (ii) Aluminium shutter glazed/skeleton section 50x20x1.50mm thick. (iii) Aluminium grill size 50mmx50mm and 4 to 5mm thick bars (iv) Fixing arrangements of hold fast in walls embedded in PCC (1:3:6) including making good the distributed surfaces. (v) Glass 4mm thick orinary quality and fixed with rubber gasket for glazed shutter. (vi) Stainless steel wire mesh 0.36mm nominal dia avg width of aperature 1.14mm and fixed with rubber gasket for gauzed shutter. (vii) Aluminium disc /bow hanle and locking system etc complete

S&F in repair Door stopper, Mild steel powder coated body, with hard drawn steel spring, 150mm size fixed to door all as specified & directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F Mild steel framed work as in doors or gates, grade Fe-410-w (Gde-E-250) quality B of angle or other section with gusset plates,rails,braces,etc complete drilled for fixing of steel sheeting or other covering.Doors,etc.to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging also fastening and fixing complete all as specified and directed.

M&L for Pressed steel door frames of size 125x60mm with open or more rebated on the solid rounded or chemfered put together with glue pinned at joints all as specified & directed

S&F Flush shutters 30mm thick, solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal lipping beading all round fixed as in Door Shutter, Cup board shutter & Kitchen rack all as specified & directed.

S &F Second class hard wood factory made glazed and skeleton shutter 35 mm thick, open rebated and prepared to receive glass, guage etc edge of framing plain chamfered or rounded fitted with cut and mitred beads for securing guage etc size of members of shutter as specified in SSR Part I Section 8 clause 8.24 (a) supplied and fitted to chowkats all as specified & directed.

M&L for Preparation of New Wood or wood base surfaces exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified & directed.

M&L for PCC (1:2:4) type B-0 using 12.50 mm graded stone aggregate as in filling of chowkats etc complete all as specified & directed.

S&F in repairs stainless steel wire cloth, 0.24mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples including second class hard wooden fillet, wrought, cross sectional area exceeding 3 Sqcm but n.exc 6 Sqcm fixed with nails complete all as specified & directed.

M & L PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in 75 mm thick sub base to foot path/ sub base of floor etc. complete all as specified & directed.

M&L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick with gray cement and pigment, set, jointed and pointed in neat cement slurry in floor over & including screed bed 20mm thick cement mortar (1:6) complete all as specified and directed.

Material and labour for Plain Cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in coping, benching including weathering slightly rounded or chamfered angles as directed including necessary form work complete all as specified and as directed.

M & L for Hardcore of broken stone or boulders of gauge n.exc 63mm deposited spread and levelled in layer n.exc 15 cm thick, watered and rammed to a true surface complete all as specified & directed.

Raking out joints/pointing to random rubble or polygonal rubble uncoursed or brought upto in cement mortar complete all as specified & directed.

M&L for Fixing chicken mesh & binding with steel wire and Plastering average thickness 10 mm thick cement mortar (1:6).on irregular face of stone walls after dubbing out etc complete all as specified & directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified & directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc.complete all as specified & directed.

M&L 25 mm thick cement concrete type B-0,1:2:4(using 12.5mm graded crushed stone aggregate) as in sub base of floors.

M & L for Ceiling HSPC (High pressure steam cured) pre-primetered self embossed, textured designer board E-board classic (white colour) size 600x600mm, 4mm thick and including GI based frame work for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 / 30mm and web of 27mm fixed to surroundings wall using nylon sleeves and screw at 450mm centre to centre/ intermediate channel 09mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with & including ceiling section (n exc 1.2m length) of .55mm thickness having kurled web of 50mm and flange of 26mm fixed to intermediate channel at 457mm centre to centre suspended with 6mm dia GI barhangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purline from the roof with alignment clip including providing provision for light fixtures of any size complete all as specified & directed.

S&F Box type Steel Windows / Ventilators double side shutters (Windows side hung type, Ventilators top hung) pressed steel frames made out CRC Sheet of 80x60x1.25mm double rebated, Shutters box type made out of CRC Sheet of 40x20x1.0mm , windows & ventilator shutter fixed made of glass and gauge fixed with box type hinges, Aluminium die cast handles for glass shutters, Iron flat type handles for mesh shutters, Telescopic stays, etc complete all as specified incl 12mm square guard bars / grill welded with steel frame (100c/c horizontically) all as specified and directed. NOTE: (i) Quoted rate is deemed to be included the total of steel frames, steel shutters and Guard bar/Grill, beading, fittings such as handles, hinges,Telescopic stays, locking arrangements and fixing of glass and wiremesh etc. (ii) Supply only 4 mm thick sheet glass and stainless steel wire mesh be measured and paid separately. (iii) All Windows/Vent design is as per CECZ TD drg No 539

S&F Mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (anealed) not less than 0.9 mm dia or securing with clips all as specified and directed.

S&F Reinforced cement concrete (1:2:4) nominal mix, type B-0 using 12.5mm graded stone aggregate as in chajjas etc.all as specified and directed.

Taking up or down steel tubing galvanised 20mm dia bore, along with fittings complete all as specified and directed. (Note :work to be done upto 5th floor height).

Taking down carefully copper/ aluminium point wiring (light, fan, socket or power) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets etc. to be measured separately), removing materials to store for keeping in safe custody for re-use at site and making good disturbed surfaces of walls, floors, etc to match with the existing surface complete all as directed..

Taking down old un servceable DB's / Main switches any capacity complete all as directed.

Taking down old un servceable MCB's, SP/SPN / TPN complete all as directed.

M&L for Point wiring with single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1.50 Sqmm 1100 Volt grade (ISI marked) including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including Concealed PVC conduit medium duty ISI marked, not less than 20 mm dia with all fittings such as tee, bends, etc all as per IS, terminated in & including new sunk type pressed steel terminal boxes concealed in wall for mounting fittings like switches, sockets, regulators etc with and including 3mm thick phenolic laminated sheet top cover, for one light/ ceilig fan/Exhaust fan /bell point controlled by one, one way switch complete all as specified and as directed. (Note : Cost of cutting/leaving forming chases for conduits, sinking for boxes and making good in CM (1:4) deemed to be included in quoted rate.)

All as per item No. 137 herein before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch on same board with other switches -do-

All as per item No. 137 herein before but for one 3 pin 5/6 Amp socket outlet controlled by one 5 Amp switch socket on independent board -do-

M&L for Point wiring with single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 2.50 Sqmm 1100 Volt grade (ISI marked) including 2.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade (ISI marked) as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including Concealed PVC conduit medium duty ISI marked, with all fittings such as tee, bends, etc all as per IS, terminated in & including new sunk type pressed steel terminal boxes concealed in wall for mounting fittings like switches, sockets, regulators etc with and including 3mm thick phenolic laminated sheet top cover, for 3 pin 15/16Amps socket outlet controlled by 15/16Amps switch on independent board complete all as specified and as directed. (Note : Cost of cutting/leaving forming chases for conduits, sinking for boxes and making good in CM (1:4) deemed to be included in quoted rate.)

S&F Modular switch 1 way 6 Amps,1 module 240 Volts AC complete all as specified & directed.

S&F Modular type socket combination , 16 Amps 240 volts AC , 2 module, suitable for inserting 3 pin 6 Amps / 3 pin 16 Amps plug top all as specified and direced .

S&F Modular type socket combination , 6 Amps 240 volts AC , 2 module , suitable for inserting 2 pin 6 Amps / 3 pin 6 Amps plug top all as specified and direced .

Supply and fix white cover plate with frame 2 modules complete all as specified and direced .

Supply and fix white cover plate with frame 3 modules complete all as specified and direced .

Supply and fix white cover plate with frame 4 modules complete all as specified and direced .

Supply and fix white cover plate with frame 6 modules complete all as specified and direced .

Supply and fix white cover plate with frame 8 modules complete all as specified and direced .

Supply and fix Modular metal flush box 1 / 2 modules complete all as specified and direced .

Supply and fix Modular metal flush box 3 modules complete all as specified and direced .

Supply and fix Modular metal flush box 4 modules complete all as specified and direced .

Supply and fix Modular metal flush box 6 modules complete all as specified and direced .

Supply and fix Modular metal flush box 8 modules complete all as specified and direced .

S&F Modular type 1-way Bell push switch , 1 module 6 Amps 240 Volts AC complete all as specified and direced .

S&F Electric calling Bell Ding Dong AC 230 Volts, single pole / Multi Music type complete all as specified and direced .

S&F Stepped type electronic modular fan regulator 2-module, modular type 120Watts, 2 Module 230 Volts AC complete all as specified and direced.

S&F ceiling rose, PVC / Polycarbonate insulated body, 65mm x 50mm with three terminals 240 Volts AC , ISI marked, including PVC square mounting block complete all as specified and directed.

Supply and fix LED tube light fitting, 1x10 watts, 6000k 230 volt, with extruded aluminium housing provided efficient heat disspation with poly corbonate diffuser, all pre-wired fixed on walls with all fixing accessories such as 2 nos of PVC square/round blocks, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed.

Supply and fix LED tube light fitting, 1x20 watts,6000k 230 volt, with extruded aluminium housing provided efficient heat disspation with poly corbonate diffuser, all pre-wired fixed on walls with all fixing accessories such as 2 nos of PVC square/round blocks, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed.

Supply and fix LED Light fitting 36 watt of size 2' x 2' LED luminare recessed mounted with polymer diffuser complete with accessories suitable for armstrong/Grid ceiling with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

S & F Electric water heater (Geyser) 25 litre storage capacity, 5 Star rating, glass line Inner tank plastic outer body PUF insulation , operating on single phase 230Volts, AC Supply along with & including hot & cold high pressure PVC connecting pipes heavy duty of 600 mm long suitable for both inlet & outlet hot water fixed with brass adopter / union washer both sides fixed as per manufacturers instructions , making necessary connections & testing on completion complete all as specified & directed. (Note : Quoted rate deemed to be included the taking down any type and size of Geysers (water storage heater) fixed with any description after dis-connecting necessary water connection & electric connection shall be deposited to E/M Store yard)

Supply and fix Sheet metal enclosure (ISI marked) distribution board VTPN, 415 volts, 4 way vertical type double door type, 200 Amps rated neutral copper bus bar for housing MCB and fixed and tested on completion complete all as specified.

S&F Sheet metal enclosures for MCB DB, triple pole and Neutral, 8 way double door ,415 Volt horizontal type, with 200 Amps rated Bus bar fixed in wall / nitch for housing MCB's complete all as specified and directed.

Supply and fix MCB Tripple pole & neutral 100 Amps 415 volts, C series,16 kA rupturing capacity providing in DB complete all as specified & directed

S&F MCB SPN 'C' curve 32 Amps/ 40amps 240 Volts , 50 HZ, 10KA repturing capacity complete all as specified & directed

S&F MCB SP 6-32 Amps 'C' curve, 240 Volts , 50 HZ, 10K repturing capacity , suitable for lightning and other domestic complete all as specified & directed

M&L for Sub main wiring with 2 runs of 6 sqmm, single core, PVC insulated & unsheathed cable FRLS conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in existing conduit fixed on wall with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 6.sqmm single core PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board as ordered and testing on completion including taking down old submain wiring complete all as specified and directed. (Note : Cable 6sqmm 3runs measured as one unit )

S&F Galvanised Iron tubing medium grade 25 mm dia bore, ISI Marked conforming to IS 1239 Part-I 2004, including all fittings such as bends, elbows, tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc,complete all as specified and directed

S&F Gun metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778 : 1984, suitable for pipe 25 mm dia bore complete all as specified and directed.

S&F Gun-metal gate valve with iron wheel head, screwed both ends for iron pipe and fixed, ISI marked conforming to IS 778 : 1984, suitable for pipe 40 mm dia bore complete all as specified and directed.

M&L for taking down and dismantling of ceiling fan 1200mm/1400mm sweep 230 Volt 50 Hz AC of any make or model by opening the cover, separating down rod, rotor and stator assembly, locating the fault and making the fan fully in serviceable condition with & including replacing the bearing with similar type of exisitng one, worn out screws of the cover, split pin, locking nuts & machine screws with spring washer for ceiling fan blades, oiling and greasing etc, finally painting the ceiling fan with one coat of spray painting with white DUCO Paint & lettering & Numbering the same as per existing ,re-assembling, connecting twin core flexible copper wire of size 23/0.0076, testing the fan complete all as specified & directed.

M & L for Rewinding of ceiling fan of size 1200mm/1400mm sweep, 230 volt, 50 Hz AC by removing of burnt winding wire from stator and rewinding the same with super enamelled copper winding wire of same gauge, same weight & turns including varnishing of winding , testing for smooth functioning complete all as specified & directed. (Note : Taking down & refixing back will be measured under Item No 188 seperately)

S & F Exhaust fan, single phase, 150 mm sweep, plastic body 1200 RPM including fixing of mounting frame, louvers, including round/square hole cutting in the wall/ventilator etc, by means of rugged bolts, nuts and washers etc,including connecting with three core copper conductor flexible cord of 0.5 Sqmm cross sectional area of required length from ceiling rose to the porcelain connector block, complete all as specified and directed.

S & F Exhaust fan, single phase, heavy duty, 300 mm (12") sweep, metal body 1400 RPM including fixing of mounting frame, louver, including the round hole cutting in the wall, by means of rugged bolts, nuts and washers etc,including connecting with three core copper conductor flexible cord of 0.5 Sqmm cross sectional area of required length from ceiling rose to the porcelain connector block of the exhaust fan, complete all as specified and directed.

S&F Building security light light fittings LED street light 35 Watt with New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having bottom Opening seperate driver compartment with IP 66 protection and impact resistance of IK 08 with all accessories and including connection up with twine core twisted flexible copper conductor cable with 1.5 M long suitable size all as specified and directed.

S&F in repair security light bracket made out of 25 mm bore G I light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 32mm X 5 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete including taking down unserviceable bracket all as specified and directed.

S&F in replacement of sheet metal enclosure of size 800 x 400 x 200 mm grouted on wall/floor in PCC with nuts and bolts made out of 2 mm thick CRCA sheet, having two nos chamber for housing of one energy meters and SPN MCB with Peeping glass fixed PVC frame and one MCB SPN with fixing rail and suitable busbar chamber for fixing two Nos aluminium strips 300 Amp capacity each making holes for fixing aluminium lugs, complete internal wiring with 6 sqmm multistranded copper cable FRLSH, epoxy based bakelite sheet of suitable size for fixing of energy meters & MCBs, including indl chamber locking system complete all as specified and directed

Supply and laying XLPE Insulated, screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade of Size 3.5 core x 35 sqmm complete all as specified & directed.

Excavation in trenches not exc 1.5 mtr wide and not exc 1.5 mtr in depth and getting out in soft / loose soil for laying of cable / errection of poles / stay assembly etc complete all as specified and directed.

Returning filling in trenches including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and directed.

Removing of surplus soil to a distance not exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and directed.

Supply and lay common burnt sub class B bricks size 230 x 115 x 75 mm, laid at right angle on the cable in trenches for cable protection complete all as specified and directed.

Supply and spreading clean dry river sand in trenches for cushioning of UG cables complete all as per Para 19.75 of SSR Part-I all as specified and directed.

S&F Galvanized iron pipe, light grade 50mm dia bore for protection & passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings/clamps as required at site all as specified & directed.

M&L Earthing with galvanised steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI wire 6mm dia by means of of nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR-2009 (Part-I) and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth wire including PCC (1:2:4) pit with RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 8mm dia TMT bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia medium grade G I pipe, funnel, wire mesh, common salt charcoal, necessary excavation and earth work in any type of soil complete all as specified & directed

Supply and fix Switch piano, flush button single pole, 5 Amps one way complete all as specified & directed

Supply and fix Switch socket combination, flush type, 5 Amp 2/3 pin muliti purpose complete all as specified & directed

Taking down and Refixing any type and size of Exhaust fan in any description after repair or winding etc making necessary connections & testing on completion and making good distrubed surfaces of wall, ceiling etc complete all as directed.

M & L for Rewinding of Exhaust fan of any type & size with appropriate size of super enamelled copper wire including varnishing, heating with proper insulation complete and testing on completion all as specified and directed .

Supply and fix in repair Sheet metal enclosure MCB distribution board SPN, 230 volts, 4 way Horizontal type, double door, (ISI marked) 200 Amps rated neutral copper bus bar for housing MCB and tested on completion complete all as specified & directed.

Supply and fix MCB single pole, 6 to 32 Amps, 240 volts, C series, 10 kA rupturing capacity complete all as specified & directed.

Supply and fix MCB single pole & neutral, 40 Amps 240 volts, C series,10 kA rupturing capacity complete all as specified & directed.

Supply and laying XLPE Insulated, screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade of Size 10 sqmm x 4 core complete all as directed.

S&F Switch socket combination, flush type 5/16 Amps 5 in 1 universal type complete all as specified & directed.

S & F of Fan regulator electronic, step & socket type 230 volt, suitable for 1200/1400mm sweep ceiling fan complete all as specified & directed.

M&L for Sub main wiring with 2 runs of 4.0 sqmm, single core, PVC insulated & unsheathed cable conforming to IS-694, FRLS, 1100 volts with copper conductor multi stranded drawn through & including non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4 sqmm single core PVC insulated & unsheathed copper conductor FRLS Cable as continuos earth wire dolly and connecting to existing main switch board / distribution board of the building as ordered and testing on completion including taking down old submain wiring with conduit complete all as specified and directed. (Note : Three run of 4sqmm cable and one run of conduit altogether will be measured as one unit)

S&F in replacement Sheet metal enclosure distribution board for 415 volts, TPN 4 way Vertical type, double door, ISI marked Triple pole and neutral with 200 Amps rated copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as specified & directed.

Supply and fix in repairs MCB Triple pole & neutral 40 to 100 Amps, 415 volts, C series,10 kA rupturing capacity providing in DB complete all as specified.

Supply, fixing and commissioning XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables ( heavy duty) of 25 sqmm x 4 core aluminum conductor, 1100Volt grade fixed on walls with fixing acessories, commissioning, testing etc including taking down old cable all as specified and directed.

Supply, fabrication, installation and testing of Junction box of size 900mm(H) X 700mm (B) X 400mm(W), L T out door type, factory made, CPRI Approved, made out of 3.15mm thick CRCA sheet duly supported with mild steel angle iron frame of size 40X40X5 mm, Powdre coated, One Incoming MCCB 4Pole 100 Amps, rupturing capacity 25 KA, 04 Nos aluminium bus bar of of capacity 250 Amps with drilled hole for incoming/outgoing cable connection with necessary alumiium lungs, GI nuts bolts and washer including 08 Nos bridge insulator DMC , heavy duty, suitable for 3 Phase 4 wire system, one danger notice plate of 1.6mm thick mild steel sheet, vitreous enameled white with letters, figures and conventional skull & bones in signal red colour and fixed in front door, foundation with PCC (1:3:6) type C-2 foundation 0.30m above normal ground level & 0.30m below ground level including necessary exacavation and earth work, Indicating lamp LED type 240V 50 Hz AC -one set of 3 all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI earth wire of 4 mm dia by means of of nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR-2009 (Part-I) and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth including PCC (1:2:4) pit chamber with RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 8mm dia TMT bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia medium grade pipe, funnel, wire mesh, common salt charcoal, necessary excavation and earth work in any type of soil complete all as specified & directed.

Supply and fix MCCB Triple pole & neutral 100 Amps 415 volts, 16 kA rupturing capacity providing in DB complete all as specified & directed.

Supply and laying XLPE Insulated, screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade of Size 25 sqmm x 4 core complete all as specified & directed.

M & L for Design, Fabrication, supply, installation, commissioning and testing L T panel board, Double Door manufactured from CPRI approved firm with canopy head, out door, cubical type overall minimum dimension 1.2 m (L) X 1.00m (H) X 0.50m (W) fabricated with 3.0mm thick CRCA sheet on mild steel angle iron frame 50X50X6 mm, totally enclosed type dust & vermin proof, back side openable fixed with hinged shutter and front side openable with hinged shutter and locking arrangement for individual MCCBs/MCBs, powder coated finished both internally and externally suitable for 415Volt AC 50 Hz 3 Phase 4 wire system by means of Alluminium bus bar 400 Amps Capacity (Main bus bar ) and 800 Amps Loop Bus bar with coloured insulating tape / sleeves mounted on porcelain or synthetic insulators with provision for fixing MCCBs/MCBs necessary inter connections with Aluminium bar / strip duly coloured code insulation and providing under mentioned equipments & accessories including connections of all out going / in-coming existing/New cables of required size and including PCC foundation in 1:3:6, type C1 of 0.5 mtrs height above GL and 0.30mtrs below GL including necessary earth work complete all as specified and as directed with following accessories :-

INCOMING: MCCB 4 pole 250Amp,Icu=Ics=25KA, Adjustable thermal and adjustable Magnetic setting with extended terminals - 01No OUTGOING: (i) MCCB 4 pole 160Amp, Icu=Ics=25KA, Adjustable thermal and adjustable Magnetic setting with extended terminals-02 Nos (ii) MCCB TPN 100-63Amp, 16KA,C curve -02 Nos (iii) Indicating lamp LED type 240V 50 Hz AC -one set of 3

M&L, Earthing with galvanised steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI strip 25 x 4 mm as earthing lead by means of of nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR-2009 (Part-I) and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth including PCC (1:2:4) pit with RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 8mm dia TMT bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia medium grade pipe, funnel, wire mesh, common salt charcoal, necessary excavation and earth work in any type of soil complete all as specified & directed

PRAGATHI BUILDERS (BID ID -3462334)

K. VENKATESH NAIDU (BID ID -3464745)

S.R.M.K Enterprises (BID ID -3464984)