Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹11.1 CrAccepted-AOC VILLAGE DOLIPUR PASANA KARCHANA PRAYAGRAJ | PRAYAGRAJ | PRAYAGRAJ | UTTAR PRADESH | ₹11.1 Cr Quoted ₹11.4 Cr | L1 | Accepted-AOC Financial bid accepted Rs. 110854168.33 |
| 2 | L2₹11.6 CrRejected-Finance KARNATAKA | RAICHUR | KARNATAKA | 584123 | ₹11.6 Cr | L2 | Rejected-Finance L2 |
| 3 | Rejected-Technical MADHEPURA | - | - | Rejected-Technical Reject |
| 4 | Rejected-Technical | - | - | Rejected-Technical Reject |
Tender Value
Refer Docs
EMD Value
₹23.3 L
Closing Date
6 Mar 2024, 12:00 pmClosed
S.E, Jhansi Circle, P.W.D., Jhansi
Office of the S.E, Jhansi Circle, P.W.D., Jhansi
Construction work of Veerangana Jhalkari Bai Government Women Polytechnic in Jhansi district
2024_CEJNS_908407_1
717/44C-Jhs Cir/2023 Date 02.02.2024
Open Tender
Civil Works - Buildings
365 days
Jhansi
Please refer Tender documents.
3 documents required · 3 mandatory
₹7,950
₹23.3 L
Yes
Office of the S.E, Jhansi Circle, P.W.D., Jhansi
29 Mar 2024
1 Mar 2024
6 Mar 2024
1 Mar 2024
6 Mar 2024
1 Mar 2024
1 Mar 2024
Amount
Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared. DSR 2.31
Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: DSR 2.6.1
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-Charge. Ordinary rock DSR 2.7.1
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. DSR 2.25
1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). DSR 4.1.8
2.27 Supplying and filling in plinth with sand under floors,icluding watering, ramming,consolidation and dressing complete DSR 2.27
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. DSR 2.35.3.1
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level DSR 5.33.1.1
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works above plinth level upto floor V level DSR 5.33.2.1
Brick work with clay fly ash bricks (non modular) bricks of class designation 7.5 in sub structure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) With Cement mortar 1:4 (1 cement : 4 coarse sand) : DSR 6.32.1
Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources). DSR 4.10
Providing and applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. DSR 4.13
Brick work with clay fly ash bricks (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) With Cement mortar 1:4 (1 cement : 4 coarse sand) : DSR 6.32.1
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding in Super Structure. Thermo-Mechanically Treated bars of grade Fe-500D or more. DSR 5.22.6
Cement Plaster in Fine Sand 12 mm cement plaster of mix 1:6 (1 cement: 6 coarse sand) DSR 13.1.1
Providing & Fixing of Chiken Wire mesh with iron screw in junction of wall and rcc coulmn proper completion of the work. SOR S.I No. 28 (iii) Pg.No 19
15 mm cement plaster 1:4 (1 cement: 4 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall. DSR 13.2.1
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) DSR 4.1.3
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 1000x1000 mm DOUBLE CHARGE with heavy duty DSR 11.41A.1.5
Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 11.37
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick. DSR 11.26.1
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. DSR 11.27
10.31Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 40x40x6mm, joints mitred and welded by angle iron 40x40x6mm or 40x 6 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. DSR 10.31
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) DSR 21.1.1.2
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc. DSR 9.48.2
Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: Butt hinges and necessary screws shall be paid separately) Second class teak wood 35 mm thick shutters DSR 9.5.1.1
Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm). DSR 14.5.1
Supplying and fixing galvanised Mosquitos proof ,heavy quality iron wire gauge or expanded metal ef heavy quality over windows and including supply and fixing of C. P. Teak wood battens 8 cm X 1 cm (3"x3/8") and including supply of necessary screws, all materials, labour and T&P etc. required for proper completion of the work, SI. No. 455
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR 13.80
Distempering with 1st quality acrylic distemper (ready mix) having VOC content less than 50 gram/litre, of approvved manufactiurer and of required shade and colour all complete to achieve even shade and colour 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement prime. DSR 13.41.1
Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. DSR 13.48A.1
Providing & Laying "brick bat coba" 100 mm thick laid with M-150 class brick bat coba 7.50 cm thick with gap of 15 mm to each other, over 20 mm thick base of cement mortar 1:4 cement and coarse sand mixed with water proofing compound spreading cement slurry mixed with aerelic cement concrete water proofing compound filled gaps of coba & top of coba mortar mixed with water proofing compound in 1:4 cement and coarse sand mortar finished smooth & top mashed false square 30 cm X 30 cm and side wall parapet shall be monotythic plaster wall upto 30 cm higher and junction and corner shall be rounded by brick ballast cement and coarse sand and masonry coba with top finishing plaster mixing with acetic water proofing compound @ 2% by weight & Including supply of all materials labour T&P etc. required for proper completion of works. SI. No. New Item 1 Ch. No. 11
Varnishing with varnish of approved brand and manufacture: 13.113.2 One or more coats with copal varnish. DSR 13.113.2
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by thee Engineer-in-Charge DSR 22.7.1
Supply & filling of cinder in sunken portion of building including breaking into required sizes including supply of all material, labour, T&P required sizes including supply of all material, labour, T&P required for proper completion of work. SI. No. New Item 3 Ch. No. 11
Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in- charge. The product performance shall carry guarantee for 10 years against any leakag . For vertical surface two coats @ 0.70 kg per sqm. as DSR 22.23.1
Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. DSR 11.37
Concrete with 4 cm(1.5") gauge brick ballast fine local sand of 1.25 Fineness modulous and cement in Proportion of 12:6:1 in foundation and under floors including supply of all materials labour and T&P etc. required for proper completion of the work. but in tbe proportion of 8:4:1 SI.No. 275 (In Plinth Ptotection Work)
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate. DSR 11.3.1
Providing and laying of 80mm Interlocking concrete block pavement laid in stone dust base and fill joint with fine sand. Joint filled after labling and dressing base including supply of all material, labour, T&P etc required for proper completion of the work. SI. No. New Item 3 Ch. No. 14 (Campus Pavement Work)
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approvedmake, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. DSR 8.31
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). DSR 10.28
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes DSR 18.8.1,
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal outer dia Pipes DSR 18.8.2,
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes DSR 18.8.3,
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. Concealed work, including cutting chases and making good the walls etc. 32 mm nominal outer dia Pipes DSR 18.8.4
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. ETERNAL WORK 40 mm dia nominal bore DSR 18.9.5
Providing and fixing Fullway Gate Valve with C.I. wheel of approved quality. 20 mm nominal bore DSR 18.17.1A
Providing and fixing Fullway Gate Valve with C.I. wheel of approved quality. 25 mm nominal bore DSR 18.17.1
C.P Brass Stop cock heavy quality (Gem Mikadeo/Encess’s williams or eqv.) 15 mm nominal bore DSR 18.52.1
Supply and installing of low density polyethylene seamless one peace moulded tank and placing the same in proper position including all taxes labour and T&P etc for proper completion of the work. Tank should be ISI marked (for 500 Liters) DSR 18.48
providing and fixing white viterious china pedestal type water closet(Eropeantype)w.c pan with ISI marked white solid plastic seat and lid DSR 17.3.1
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests DSR 17.1.1
Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :Single half stall urinal with 5 litre P.V.C. automatic flushing cistern DSR 17.5.3
Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required : Range of two squatting plates with 5 litre P.V.C. automatic flushing cistern DSR 17.6.2
Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer. DSR 17.7A
Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 38 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 263 gms DSR 17.70.2,
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms DSR 17.71,
C.P. Brass towel rail 600 MM LONG mm together with pair of C.P. brass brackets to fit the towel rail. DSR 17.73.2
C.P BRASS FITTINGS 25MM P.V.C ball float valve with brass and union complete DSR 18.18.3,
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: 15MM Nominal Bore DSR 18.49.1,
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore DSR 18.51.1,
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore. DSR 18.53.1,
Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 MM DIA DSR 18.22.1
providing and fixing gun metal gate valve with C.I wheel of approved quality 25mm dia DSR 18.17.1
providing and fixing gun metal gate valve with C.I wheel of approved quality 20mm dia DSR 18.17.1A
providing and fixing gun metal gate valve with C.I wheel of approved quality 32mm dia DSR 18.17.1
providing and fixing gun metal gate valve with C.I wheel of approved quality 40mm dia DSR 18.17.3
Providing and fixing brass stop cock of approved quality : 20 mm Nominal bore DSR 18.16.2
Providing and fixing brass stop cock of approved quality : 15MM Nominal bore DSR 18.16.1
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. completeS. 110MM dia DSR 12.43.2
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion coupler 110mm DSR 12.42.1.2
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. single pushfit coupler 110mm DSR 12.42.2.2
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. single tee with door DSR 12.42.3.2
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. single tee without door DSR 12.42.4.2
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. bend 87.5 degri 110 mm band DSR 12.42.5.2
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. shoe (Plain) 110mm Shoe DSR 12.42.6.2
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm dia meter and waiting not less than 440 gram DSR 12.44
Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. DSR 12.22,
Centering and shuttering including strutting, propping etc. and removal of from for Lintels, beams, plinth beams, girders, bressumers and cantilevers. DSR 5.9.5
Centering and shuttering including strutting, propping etc. and removal of from for Foundations, footing, bases of columns etc for mass concrete. DSR 5.9.1
Centering and shuttering including strutting, propping etc. and removal of from for Columns, pillars, abutments, post and struts DSR 5.9.6
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. 300 mm dia DSR 23.1.2.1
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia DSR 23.4.2
Providing and filling sand of grading zone V or coarser grade all- round the G.I. pipes in external work. 150 mm diameter pipe DSR 18.41.10
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 DSR 16.78
Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. DSR 16.79
Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer in-Charge. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern. DSR 16.91.2
Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). DSR 16.75
Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.34.1
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) DSR 5.2.2
15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand) DSR 13.2.2
Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar D.S.R. 19.15.1
Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality MD-10-circular shape 560 dia internal dia meters DSR-19.19.3.1
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.23.1.1 All types of soil 300 mm dia DSR-23.1.1.1
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. (200mm nominal size dia) DSR-23.3.3
Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR-23.5
Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 10 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR-23.6
Supplying, filling, spreading & leveling stone boulders of size range 1.5 cm to 2 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR-23.7
Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. DSR-23.8
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : DSR 18.33.1
Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming,watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m. DSR 2.10.1.2
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. 150mm dia. R.C.C. pipe. DSR 19.6.2
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 150 mm diameter R.C.C. pipe. DSR 19.3.2
Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.34.1
Brick work with clay flyash F.P.S. (non modular) brick of class designation 7.5 in superstructure above plinth level up to floor five level in : Cement mortar 1:6 (1 cement : 6 coarse sand) DSR 6.32.2
Painting (two or more coats) on rain water, soil, waste and vent pipes and fittings with aluminium paint of approved brand and manufacture over a priming coat of ready mixed zinc chromate yellow primer on new work : 75 mm diameter pipes . DSR 13.95.1
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.32.1
Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate,suitable GI box and earthing the point with 1.5sq.mm FRLS PVC copper conductor single core cable etc. as required. (A)Light Point
(B)Fan Point
(C)Call bell Point
(D)Exhaust Point
Wiring for twin control light point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with 2 way modular switch, modular plate,suitable GI box and earthing the point with 1.5sq.mm FRLS PVC copper conductor single core cable etc. as required.
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings) (For Plug Point and Aquaguard)(4Nos. for Computer Pt.)
Supply and Fixing of suitable size GI box with modular plate and cover in front of surface or in recess, including providing and fixing 2 nos. 3 pin 5/6A modular socket outlet and 2 nos. 5/6A modular switch, connections etc. as required. (For light Plugs to be used in non residential buildings). (TV Point)
Supply and Fixing of brass Angle holder including connection etc. as required.
Supply and Fixing of suitable size GI box with modular plate and cover in front of surface or in recess, including providing and fixing 25 A modular socket outlet with 25 A modular SP MCB C curve including connections painting etc. as required.
Supply and Fixing of suitable size GI box with modular plate and cover in front of surface or in recess, including providing and fixing 6 pin 15/16 A modular socket outlet and 15/16 A modular switch connections etc. as required.
Supply and Fixing of 6 way (4+18), Double Door, Horizontal type three pole and neutral, sheet steel, MCB Distribution board, 415V, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections,powder painted including earthing etc. as required.(But without MCB/RCCB/Isolator).
Supply and Fixing 4 way, Verticle type three pole and neutral, sheet steel, MCB Distribution board, 415V, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections,powder painted including earthing etc. as required.(But without MCB/RCCB/Isolator).
Supplying and fixing of 12 way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
Supply and fixing of 5 to 32 amp rating 240/415V, 10KA, C curve DP MCB suitable for inductive load of following poles in existing DB complete with connections, testing and commissioning etc. as required.
Supply and fixing of 5 to 32 amp rating 240/415V, 10KA, C curve SPMCB suitable for inductive load of following poles in existing DB complete with connections, testing and commissioning etc. as required.
Supplying and fixing of 20mm dia sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
Submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required. (A)2*1.5 sqmm +1* 1.5 sqmm earth wire (for Plug, Aquaduard,TV)
(B)2*2.5 sqmm +1* 2.5 sqmm earth wire(Power Plug)
(C)2*6 sqmm +1* 6 sqmm earth wire
(D)2*16 sqmm +1* 16 sqmm earth wire
Supply and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1kv grade as required. 3.5* 400 sqmm (82mm)
3.5* 185 sqmm (57mm)
3.5* 95 sqmm (50mm)
3.5* 50 sqmm (35mm)
4* 25 sqmm (28mm)
2* 16 sqmm (22mm)
Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.
Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.
SITC of 1200 mm sweep, BEE 5 star rated, ceiling fan with brush less DC motor, class of insulation-B, 3 nos blades, 30cm long down rod, 2 nos canopies, shackle kit, safety rope, copper winding, pf not less than 0.9, service value (CM/M/W) minimum 6.00 air delivery minimum 210cum/min, 350rpm(tolerance as per IS: 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts,washers, temperature rise=75degree C max, insulation resistance more than 2 mega ohm, suitable for 230V, 50Hz, single phase AC supply, earthing etc. complete as required.
Supplying and fixing Two Module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
Earthing with copper earth plate 600mm*600mm*3mm thick including accessories, and providing masnory enclouser with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/coke and salt as required.
Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.
Providing and fixing H.T. danger board notice plate of 250mm*200mm made of mild steel, latest 2mm thick, vitreous enameled white on both side and with inscription in single red colour on front side as required.
Providing and fixing M.V. danger board notice plate of 200mm*150mm made of mild steel, latest 2mm thick, vitreous enameled white on both side and with inscription in single red colour on front side as required.
Supply and Fixing of 125 Amp. 4 Pole MCB (27KA), C curve
Supply and Fixing of 100 Amp. 4 Pole MCB (27KA), C curve
Supply and Fixing of 63 Amp. 4 Pole MCB(10KA) C curve
Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 50 Sqmm 3.5 core
95 Sqmm 3.5 core
185 Sqmm 3.5 core
400 Sqmm 3.5 core
Submain wiring along with earth wire with4*25 Sqmm + 2*16 Sqmm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.
Supply and fixing of 18 watt LED tubelight (Single side connection) poly carbonated tube light fitting complete including tube suitable for both Surface complete in all respect. 1800 systems lumens, Efficacy>110lm/W, PF › 0.95, THD <15% , CRI>80,Sheet thickness 0.8mm, with 5 year warrenty Photon Ultra 2.0 Model-PHOTONULTRAPLUSSN1213 T8SSTL18WLED865PCIND or Equilalent
Supply and fixing of 18 Watt LED round surface mounted downlights complete in all respect. 1800-2000 systems lumens, 110lm/W, PF › 0.9, THD <10% , CRI>80, with 5 year warrenty ZIVA surface DL Model-ZIVASURRDDLR18WLED857S or Equivalent.
Supply and Fixing of 9 watt LED DECORATIVE WALL light Complete in all Respect. Model-LHFOAJD1TZ1I060 or equivalent.
Supply and fixing of 15 watt LED wall light (Bi Directional) Complete in all Respect. 1200 systems lumens, Efficacy >140lm/W, PF › 0.95, THD <10% , CRI>80, Model- CLIOWLS15WLED830PSYMTOTG or equivalent.
Supply and fixing of 90Watt LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 90watt. Confirming to IP66 Protection having company logo engraved complete in all respect including Labour. 10350 lumens, CRI>70, PF>0.95,230V, THD<10%, CCT-5700K Model- ENDURASUNBEAMSL90WLED757SASYTOPC or equivalent.
Supply and Fixing of L.E.D. Bulbs, 15W app. Make Havells or Equivalent
Supply and laying of 1800mm x 900mm x 12mm thick chequered rubbbber matting of tested quality.
Supply and Fixing of Heavy Duty Exhaust Fan 300 mm size sweep 900 RPM single phase including cartage and fixing Complete in all respects.Make Havells or equivalent
Supply and fixing of fire extinguisher, ABC Type 6.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.
Supply and fixing of C02 type fire extinguisher 6.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.
Supply and fixing of fire bucket, round bottom made of G.I. sheet 9-11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of Engineer-in-Charge.
Supply & Installation of split direct expansion 2.0 Ton air-conditioners suitable for operation on A/C supply single phase 50 HZ 230 volts with hermetically sealed compressor with air cooled condenser with DC iinverter technology motor capacitor and start run capacitor, relay and over load protector internal unit, with one indoor and one outdoor unit. The condenser unit wiill be placed outside the room on the terrace to avoid noise including standard length of suitable size copper tubing covered with insulation tube. (High Wall Chored / Cordless) suitable capacity 3 core sheathed / PVC copper cable and a battery operated wireless remote unit. BEE star rated : 5 star, EER 3.4
S/O automatic voltage stablizer 5.0 KVA capapcity for 1.5 ton AC capacity voltage range input voltage (120-280) output voltage range (210-250)
S/F of Bracket for outdoor units.
SITC of Suction/Discharge Copper pipe line in split A.C. unit 1.8/2.0 ton capacity including brazing, nitrile rubber insulation 9mm thick class 'O' etc complete 5/8" (15.90 mm)
S/I of Heavy duty PVC plastic braided 20mm OD flexible pipe for condensed water drain with clipping accessories complete
2.5mm2 3 Core Round Cable for A.C. Connecting Indoor/ Outdoor
Supply and Fixing of Aluminium channel of Size 2"*2"*0.4" Complete in all Respect.
Supply, Installation, Testing and Commisioning of 82.5 KVA 3 Phase 415V, 50Hz liquid cooled silent DG Set comprising of diesel engine of reputed make. Fitted on a common base frame along with other accessories i.e AMF panel, battery charger, first fill of lube oil, 4 nos. chemical electrode earthing, 40 meter cable of reputed make as per PWD specifications, with foundation, earthing, cable and changover etc. complete in all respect. including cost of freight charge from ex. works to site place, etc. Two Year warranty. Compelete in all respect. Voltage-415 volt Rated output -82.5KVA, 66KW Fuel Tank Capacity 200ltr. Fuel consumption at 75% load- 13.2 ltrs/hr Governing class-G2 Noise level <75dBA No. of cylinder-4 Speed 1500 rpm Lube oil change Period- 500 hrs Insulation class-H Alternater Efficency (at 100% Load) 0.8 PF-88.9%
(A) Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS: 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325. (D) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 450 Ipm at 35 m Head
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 65 mm dia
80 mm dia
100 mm dia
Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia
80 mm dia
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80mm dia
100mm dia
Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 80mm dia
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 40m
Supplying & fixing 63 mm dia short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required: Stainless Steel (Grade 304)
Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 2 way-100 mm dia M.S. Pipe
Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
CONTROL PANEL FOR DOWNCOMER SYSTEM Supplying, installation, testing and commissioning of floor mounted dust and vermin proof LT power distribution outdoor Panel compartmentalised cubical type with ingress protection of IP 55 having front and back openable double fold doors provided with neoprene rubber gasket with pad locking arrangement and insulated door handles, minimum 350 mm deep with 4 strip 100 amp. capacity, suitable length aluminium busbars on SMC / DMC insulators, 3 Nos. LED indicator lamps (R.Y.B) with 3 Nos. toggle switches and 2 amp capacity SP MCB "C" curve protection of each LED lamp, the body fabricated from 2 mm thick CRCA sheet (with front and back tapered top / roof fabricated from 3.00 mm thick CRCA sheet), 35 mm X 35 mm x 3 mm MS angle iron frame work all round at the bottom 75 mm X 40 mm X 4.4 mm MS channel as base, 25 mm x 5 mm G.I strip as earth bar at the rare end, suitable accomodation from supplying and fixing the following switchgears and accessories, connections, interconnections with suitable size of FRLS copper conductor single core cable, control wiring inside panel for metering and protection etc. with 2.5 sq.mm FRLS PVC insulated copper conductor single core cable and door earthing with 4 sq.mm FRLS PVC insulated copper conductor single core cable and 1 No. M.V danger notice plate of 200 mm X 150 mm made of mild steel, at least 2.00 mm thick and vitreous enamelled white on both sides and inscription in single red colour on front side, painting with siemens grey powder coated paint to give a smooth surface after cleaning and finishing with 7 or more tank process, providing suitable size brick foundation of 225 mm width in three sides or more and having brick wall of total height 1100 mm, 15 mm cement plaster (1:4) on the out side exposed wall for installation of OUTDOOR PANEL complete with excavation, refilling, earthing as required. INCOMING 63 A, 25KA, FP MCCB, Ics = 100% Icu as per IEC 60947-2 with Extended ROM, Spreader Terminals. - 01 Set OUTGOING 32 A, 18KA, TP MCCB, Ics = 100% Icu as per IEC 60947-2 with Extended ROM, Spreader Terminals. - 02 Sets Providing and fixing star delta starter with suitable numbers of AC-3 duty Contactors, 25A Range, 415 volt, 50 Hz, 3 ph, and overload relay with necessary linking and control wiring etc. as required in complete shape star delta starter including ON/OFF Pushbuttons and ON/OFF Indication lamps. Providing and fixing Flush mounting Multifunction Meter with RS485 suitable for measurement in 3 phase, A.C supply,
Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required
3.5 Core, 50 Sq.mm-Armoured-Aluminium conductor Power cable.(to be clamped with 25x3mm MS flat clamp)
4 Core, 2.50 Sq.mm-Armoured-Copper conductor control cable.
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5CX 50 sq. mm (35mm)
Supply and fixing of fire extinguisher, ABC Type 6.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.
Supply and fixing of C02 type fire extinguisher 6.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.
Supplying, installation, testing & commissioning of heat detector operating at 54°C/57°C with rate of rise cum fixed tempreature (dual thermistor) type with mounting base complete with all connection etc. as required
Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.
Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required
Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required.
Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required
Supplying, installation, testing & commissioning talk back slave station in surface/recess suitable for operation on simplex mode complete with P.T.T. knob & speaker/microphone enclosed in a M.S. (16 SWG)/ ABS box with break glass in front etc. complete as reauired
Supplying, installation, testing & commissioning sector panel suitable for 4 zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all arealzone covered, complete with all connections, interconnections as reauired.
Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000 rated with annealed copper conductor having glass mica fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner bedding, steel wire armouring & LSZH outer sheath complete as required.
Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. Speaker cable Four pair, 2-core, 1.5 sqmm
Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. 16x4 core.
SIGNAGES Supplying, installation, testing and commissioning of energy saving & environment friendly laser etched LED emergency exit signage Single/double Sided GREEN/RED of standard size 300x180x25mm, super bright LED's. MS power coated housing with suitable power consumption with inbuilt battery having backup upto2 hours. complete with chain etc as required.
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)
Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.
Supply and burring of Safe Earthing Electrode T-39 Cu Copper Coated, Length up to 3000mm, outer pipe 76.3mm x 3.2 inner pipe 42.4mm x 2.6mm, terminal Dia 12mm, coating 80-100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square C.I. frame with hinged cover & masonry housing. (From electrode terminal to switch board, cost of 25 x 3 Copper Strip will be extra).
Supply & fixing of 7 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 130mm and base plate 12mm thik) having 3mm thikness with single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P completee in all respect.
Supply and fixing of 90Watt LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 90watt. Confirming to IP66 Protection having company logo engraved complete in all respect including Labour. 10350 lumens, CRI>70, PF>0.95,230V, THD<10%, CCT-5700K Model- ENDURASUNBEAMSL90WLED757SASYTOPC or equivalent.
Supply and burring of Safe Earthing Electrode T-39 Cu Copper Coated, Length up to 3000mm, outer pipe 76.3mm x 3.2 inner pipe 42.4mm x 2.6mm, terminal Dia 12mm, coating 80-100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square C.I. frame with hinged cover & masonry housing. (From electrode terminal to switch board, cost of 25 x 3 Copper Strip will be extra).
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
Supply and laying of 25 Sqmm 3.5 core aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.
Supply and fixing of 5 to 32 amp rating 240/415V, 10KA, C curve SPMCB suitable for inductive load of following poles in existing DB complete with connections, testing and commissioning etc. as required.
Numberingof pole by letter writing (number, named, agency, UPPWD) with cost of paint & needed T&P and panel , other accessories as required complete in all respect.
Making connection of each street light fitting by S/L 1.50 sq mm FRLSH copper m.s wire from pole busbar box to street light fitting.( for single Bracket Light.)
Electrical Connection As Per analysis based on UPERC cost data book Complete in All Respect.
SATYAM CONSTRUCTIONS
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Download all tender documents and submit your bid