Special Repair of PHC (Health and Wellness Centre) building at Village Pali in Mohindergarh District. (Re-invited)

Amount

Terracing consisting of tiles 22.86 cm x 11.43 Cm x 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and on other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13).

Cement Concrete 1:2:4 gola 10cm x 10cm quadrant along junction of roof with parapet wall finished smooth, where specified. (HSR 13.64)

Brick Work in Cement Mortar, First class brickwork laid in cement sand mortar 1:6 in first storey upto 4 meters above plinth level. (HSR 11.7)

Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work. (HSR 16.60)

12 mm thick cement plaster 1:6 (HSR 15.7)

15 mm thick cement plaster 1:6 on the rough side of single or half brick wal (HSR 15.12)

Plastering on under side of Ceiling, 10 mm thick cement plaster 1:4 (HSR 15.52)

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (J.K. / Birla make) (HSR 16.81)

Factory manufactured wire gauze door and window shutter of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. (non coniferous timber other than teak, conforming to I.S specification no. 1003, kiln sea soned) with 100 mm wide vertical styles 150 mm wide lock rail 200 mm wide bottom rail wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc. complete fixed in position (excluding the cost of any fittings, other than specified above but including labour for fixing the same in position) (HSR 17.92) 30mm thick

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659- 1969 bonded with water proof type phenol formaldehyde synthetic resin,hotpressesd, conforming to I.S.2202 part I and II, fixed in position,including iron hinges,screws, chocks/cleats and stops etc.(excluding the cost of any fittings other than specified above,but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges.) (HSR 17.93) (iii) 35 mm thick

Providing & Fixing Vitrified Tiles 600 x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand morter 1.3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA. (Double charged tiles shall be used as approved by Engineer in charge. (HSR 14.89).

Providing and laying 80mm thick ISI marked interlocking paver blocks confirming to IS: 15658:2006/IRC SP 63-2004 of all shapes and colours in design mix cement M-40 over a bed of 30 mm thick fine sand complete in all respects. [HSR 10.159]

Providing & fixing vitrified tiles of size 600mm x 600mm of approved make in skirting/dados laid in any pattern as specified over base of 12mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA. (Double charged tiles shall be used as approved by Engineer in charge. (HSR 14.90).

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. Digital Print tiles of Size of 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA shall be used. [HSR 14.92(b)].

Dismantling cement conglemerate / terrazzo floors 25 mm to 50 mm thick including concrete base (HSR 8.25)

Precast cement concrete 1:2:4 with stone aggregate 20 mm nominal size in Kerbs and the like items, finished smooth with 6 mm thick cement plaster 1:3 on exposed surface including from work, placing and fixing in position, complete at the ground level or in first storey. (HSR 10.77)

Providing & fixing PVC Rain Water Pipe 6 kg. pressure of ISI Mark in cement mortar during masonry work. (HSR 13.89) b) 150mm dia PVC pipe 6 kg. pressure

Providing & fixing PVC Bend ISI Mark. (HSR 13.90) b) 150mm dia PVC Bend.

Base course of floors consisting of 100 mm thick cement 1:8:16 and 100 mm sand or stone filling. (HSR 14.1)

12 mm thick cement plaster 1:4 (HSR 15.5)

15 mm thick cement plaster 1:4 on the rough side of single or half brick wall (HSR 15.10)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE ANGLO INDIAN WATER CLOSET SUIT (as approved by the Engineer-in-charge) consisting of:- (HSR 30.3)

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (to the approval of the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT WITH NONCONCEALED ‘P’ OR ‘S’ TRAP with or without vent and all other necessary fittings as fully described in item no.30.3 above. (HSR 30.4) (i) White

EXTRA OVER Item nos. 30.1 to 30.4 and 30.6 FOR PROVIDING AND FIXING 15 LITRES CAPACITY LOW LEVEL VITREOUS CHINA WARECISTERN complete with flush bend all other necessary fittings instead of C.I. high level cistern complete with fittings.(HSR 30.12)

EXTRA OVER item nos.30.3 to 30.6 FOR PROVIDING AND FIXING BEST INDIAN MAKE PLASTIC HYGENIC SEAT with lid complete instead of hollow black or white plastic seat and lid. (HSR 30.13)

PROVIDING AND FIXING POSITION BEST INDIAN MAKE FLAT BACK OR ANGULAR LIPPED FRONT URINAL 465 MM HIGH CONSISTING OF : - (i) Flat back lipped or angular urinal basin of VITREOUS CHINA WARE (to the approval of the Engineer-in-charge). (ii) 5 LITRES CAPACITY mosquito proof INDIAN MAKE C.I.AUTOMATIC FLUSHING CISTERN, PAINTED WITH non-yellowing white enamel paint or other approved shade enamel paint on outside and superior black bitumastic paint on inside complete with screwed 15 mm pipe; (iii) PAIR OF R.S.PR C,I. PAINTED BRACKETS AND BRASS COUPLINGS; (iv) Standard size G.I.FLUSH PIPE WITH C.P.BRASS WALL CLIPS AND UNIONS COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOOR AND PAINTING OF FITTINGS ETC. (as required by the Engineer-in-charge).(HSR 30.19)

Providing and fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of the Engineer-in-charge) (HSR 30.78)

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality (HSR 30.75)Bib Cock long body

Providing and fixing in position C.P. brass stop cocks (HSR 30.76) Stop cock male and female end

Providing and fixing HDPE Water Storage Tanks of Sintex, Diplast OK Supreme make with covers/lids marked with IS 12701 on roof top of building including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respect to the satisfaction. (HSR 30.119) 500 Ltr

1000 Ltr. Capacity

Providing & laying 100 mm thick granular sub base consisting of drainage layer confirming to table 400.1 Grading-III of MoRT&H 5th edition, mixing in a mechanical mix plant at OMC, carriage of mix material to the site of work, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory powder roller to achieve desired density complete as per Clause No. 401 of MoRT&H specifications. (N.S.)

Sachin Sharma

Varun Sharma

The Ishwar Singh Co. Multipurpose Society Ltd.

Ami Lal