PROVISION OF AREA DRAINAGE AND CONNECTING PATH NEAR BLDG NO P-142 AT JAL VIHAR, ADDN / ALTN TO MI ROOM PARKING SHED AT INS JARAWA AND PROVISION OF ROAD FURNITURE WORK AT THE ENTRANCE GATE AND CONVEX MIRROR AT MO (PBR) UNDER GE HADDO, PORT BLAIR

Amount

Surface excavation n. exc 30 cm deep and averaging 15 cm deep in any type of soil and getting out complete all as specified and directed

Excavation in trenches n. exc 1.5m wide and n. exc 1.5m in depth in hard/dense soil for foundation, etc or for shafts, wells, cesspits, manholes, pierholes, etc n. exc 10 Sqm on plan and getting out complete all as specified and directed

M&L for removing excavated material (Soils) to a distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed

M&L for returning filling in hard/dense soil including spreading levelling watering and well ramming in layers n. exc 25cm thick complete all as specified and directed

M&L for hardcore of broken stone or boulders of gauge n. exc 63 mm deposited spread and levelled in layers n. exc 15 cm thick watered and rammed to a true surface

M&L for Cement concrete 1:4:8 type D2 (using 40mm graded aggregate) as in sub base, foundations or mass concrete complete all as specified and as directed by the Engr-in-Charge

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design and pattern as in footpath, parks, lawns, drive ways or light traffic parking etc of required strength, thickness and size/shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified

M&L for PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in coping, edging including necessary form work complete all as specified

M&L for plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in surface channel or drain or benching in manhole including necessary formwork complete all as specified and directed

M&L for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitered/stopped ends etc complete all as specified and directed

Demolition of precast cement concrete block walling built in CM or cement lime Mortar complete all as specified and as directed.

M&L precast cement concrete block masonry exc 10 cm width with solid block PCC 1:3:6 type C1 (using 20 mm graded stone aggregate) and setting in cement mortar 1:4 all as specified

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed

M&L for 15mm thick plaster in CM 1:4 on fair face of concrete surface or brick walls finished even and smooth without using extra cement complete all as specified

M&L for preparing newly plastered wall surface and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm complete all as specified and directed

M&L for design mix M-30 (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, chajja/facia and the like complete all as specified and directed

M&L formwork for rough finished flat surface to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar works conforming to Fe-290, Gde-E-165 all as specified and as directed

M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces of any description over 10cm width or girth not otherwise described complete all as specified and directed

M&L for 10mm thick plaster in CM 1:6 on fair face of concrete surface or brick walls finished even and smooth without using extra cement complete all as specified

M&L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of average 1mm thick wall care putty to make the surface smooth complete all as specified and directed

M&L for plastering the wall/ceiling surfaces 20mm thick in CM 1:3 using Nito Bond SBR of Fosroc @ 7 Ltr per bag of cement or equivalent make of Dr Fixit of Pidilite Industries or @ 5% by weight of cement of Harjas Coatings and Polymers. Make : Nito Bond SBR and Nito Bond AR of Fosroc or equivalent make of Dr Fixit of Pidilite Industries or of Harjas Coatings of Polymers

M&L for preparation of newly plastered ceiling surface and applying two coats of oil bound distemper of approved tint over a coat of average 1mm thick wall care putty complete all as specified and directed

Demolition of cement concrete (Un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) complete all as specified and directed

M&L for 20mm thick plaster on RCC roof slab in CM 1:4 including liquid water proofing compound @ 200ml per 50 Kg cement bag complete all as specified

M&L PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in levelling course, padding, sunken, coping portion rounded chamfered on edge complete all as specified and directed

Supply only liquid water proofing compound

M&L for applying a coat of cold bituminous primer over cleaned surface @ 0.30 Kg/Sqm and applying one coat of hot blown bitumen 85/25 grade @ 1.2 Kg/Sqm over primer followed by APP modified polymeric membrane 3mm thick, minimum weight not less than 3 Kg/Sqm, reinforced with polyester non-woven fabric weight not less than 150 Gm/Sqm laid as per the manufacturer's instruction with side over lap of 100mm and end over lap of 150mm, tucked into the chases on vertical surfaces and painting over APP membrane sheet with aluminium paint @ 0.10 Kg/Sqm complete all as specified and directed

Excavation in post hole in hard/dense soil (or similar holes) each n. exc 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25cm, watering, and removing surplus soil to a distance n. exc 50m and making good surface complete all as specified and directed

M&L for cement concrete 1:2:4 type B1 (Using 20mm graded stone agrregate) as in foundation of posts, railing and similar work complete all as specified and directed

S&F mild steel roof trusses (framed), trrussed, purlins, crane gantries, rails and fastenings and heavy bracket framming (Beam,Tee, Angle, Channels or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde-E-250) quality-A

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410-W (Gde-E-250) quality-A complete all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridges, fixed with self tapping screws all as specified and directed

M&L for 75mm thick PCC 1:3:6 type C1 (Using 20mm graded stone aggregate) as in plinth protection/path laid in panels, finish the top surfaces even and smooth complete including filling the joints with mastic compound all as specified and directed

M&L for 100mm thick PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in path finish the top surfaces even and rough to receive top layer complete all as specified and directed

M&L for chequered cement concrete tiles of size 30cm X 30cm X 25mm thick with grey cement and pigments set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile as in floor over and including 20mm thick screed bed in CM 1:4 complete all as specified and directed

S & F in repairs poly carbonate convex mirror outdoor type 1000mm dia made out of Fibre along with bracket, pole mounted and fixed to MS pipe embedded in PCC including necessary earthwork required for post holes complete all as specified and as directed by the Engr-in-Charge. Make : Frontier polymers Pvt Ltd Model No. FCMO-100 or equivalent model of made as approved by GE. Note :- PCC, MS Post, painting to steel work will be measured and paid seperately.

M & L for cement concrete type B1 1:2:4 (20mm aggregate) in foundations, filling and mass concrete.

S & F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc, Wind ties for roof including securing bots, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. Flat iron fillets (for securing wire mesh etc). including all necessary drilling, bolting or riverting, etc. and similar work conforming to Fe-290 Gde E-165.

M & L for preparing of new of previously untreated steel surface of any description, not otherwise described, over 10cm width or girth applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

Supply and fix rubberised speed breakers (of size 500x400x50mm) fixed with MS zinc coated screwed nails of size 16mm dia 200mm long including drilling, fixing the nails and sealing compound as required at site complete all as specified and as directed by Engr-in-Charge.

V M YOUSUF

M/s K Moorthi

M/s Ramesh Lal

M/s Prem Enterprise

M/S AMK CONSTRUCTIONS

MAJUMDAR FURNITURE

P Babu