SPL REPAIR TO BLDG NO 305 (OTM ACCN) OF JAT AT ITARANA MIL STN ALWAR

Demolition of brick/stone masonry built in cement/lime mortar of any mix including all quoins pillar ashlars masonry and removal complete all as specified and directed.

Dismantling of stone slabs or tiles of any description or thickness as in floors etc laid dry or laid dry and pointed complete .all as specified & directed.

Demolition of cement concrete (un-renforced) in ground floor and paving N. exc. 15 cm thickness (below or above ground level.) & removal of rubbish material complete all as specified and directed.

Taking down Chowkatts or frames with shutters ( without taking off shutters from the frame exc 1.5 sq. m but n exc 4 sq m each & removing to store complete all as specified and directed.

Taking down Chowkatts or frames with shutters ( without taking off shutters from the frame n. exc 1.5 sq. m each & removing to store complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish of the premises complete all as specified and directed.

Taking down cement plaster any description on brick or stone any description complete all as specified and directed.

Taking up or down 15mm steel tubing and connections, complete all as specified and directed.

Taking up or down 20mm steel tubing and connections, complete all as specified and directed.

Dismantling/demolition water tanks of capacity n exc 1000 ltr and removing from site complete all as specified and directed.

Dismantling of 110mm bore PVC(SWR) drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L brick work with FLY ASH BRICKS {As per IS-13757 (1993) burnt clay fly ash building bricks}, (OLD SIZE BRICKS) straight or curved on plan to any radius in half brick thick wall, built in cement mortar 1:4 complete all as specified and directed.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2 mm plain colour PVC sheet on back face, supplying and fixing in frame at site complete all as specified and directed.

S&F 35mm thick IInd class hard wood factory made panelled door shutter(two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. the size of rail and stiles as per IS: 1003 (part-I), kiln seasoned and chemically pressure treated and fixed to chowkats complete all as specified and directed.

S&F 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F Steel windows box type with side hung shutters including projecting type hinges with steel handle 150mm, and steel peg stay, complete with glazing bars, dovetailed or welded & factory made (XW2)M/F) double shutter, openable shutter with glazing bars and other openable shutter without glazing bars, fabricated with members of standard size as shown on drawings including frames complete all as specified. Note :- The quoted rates shall be deemed of lugs and FI required for fixing wire cloth, Sheet Glass, Grills, iron mongry and guard bars as shown on drg.

S&F steel ventilator with top hung shutter including hinges steel peg stay complete including taking down complete all as specified and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; cooler Stand, framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook & pintel hinges; large hasps & staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way & three way straps,plate washers & similar small articles conforming to Fe290-0 Gde E-165etc complete. all as specified and directed

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel wire staples or nails and screws complete all as specified and directed

S&F Sheet glass, ordinary quality, in squares n exc 0.5 sq. m each pane 4 mm in thickness complete all as specified and directed.

M&L for preparation of new wooden surfaces over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete.

S&F Butt hinges 100mm long medium weight, stainless steel complete all as specified and directed.

S&F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150mm 'D' type Aluminium handles, type, anodised complete all as specified & directed by Engr-in-Charge.

S&F 150mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring. Fixed in floor complete all as specified and directed

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate), 25mm thick, as in floor complete all as specified & directed by Engr-in-Charge.

M&L non skid ceramic tiles 7 to 8mm thick(square/rectangular) colored tiles area of each tiles exc 0.06 sqm but n.exc. 0.11 sqm in floor set and jointed in neat cement slurry and pointed in white or coloure cement and over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Material and labour for Machine cut kota stone slab flooring 18-20 mm thick size not less than 22" x 22" laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 20mm thick cement screed bed in cement mortar 1:6 including rubbing and mirror polishing complete all as specified and directed.

Material and labour for kota stone slab 18 -20 mm thick in riser of steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick rendering in cement mortar 1:4 including cutting, moulding outer edges, rubbing and mirror polishing complete all as specified and directed.

S&F in repairs stainless steel rod of 20 mm inner dia (in lengths as directed) including decorative finial at both ends and pair of stainless steel brackets fixed at both ends with rawl plug & steel screws on walls/beam, all as specified & as directed.

M&L 75 mm thick PCC(1:3:6) type C2(using 40mm graded stone aggregate ) as in plinth protection finished fair and even using extra cement for smooth finish complete all as specified and directed.

M&L Rendring 10mm thick in CM 1:6 on brick work / stone or concrete surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on brick work /stone or concrete wall surfaces fair faces of brick work & surfaces finished even and smooth without using extra cement with water proof compound ( water proof compound paid seperatly) complete all as specified and directed.

Supply only Integral waterproofing compound complete all as specified and directed.

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified and directed.

Material and labour for prepration over new surface and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as er IS 15489-2004 alkarili and fungal resistance, dirt resistance exterior paint emulsion of required shade (Company Depot tinted) with silicon addtitives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10 sqm complete all as specified and directed.

M&L for providing and applying minimum 1mm thick wall care putty over prepared surface to achieve the surface even and smooth for painting complete all as specified and as directed

Material and labour for complete removal of existing treatment from stone wall /plastered wall and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as er IS 15489-2004 alkarili and fungal resistance, dirt resistance, exterior emulsion paint of required shade (Company Depot tinted) with silicon addtitives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10 sqm over 1mm thick wall care putty over prepared surface to achieve the surface even and smooth for painting complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

Material and labour preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying two coats of Oil bound distemper over a coat of alkali resistant primer on walls and inclucluding 1 mm thick Birla white wall care putty complete all as specified and directed.

M & L for complete removing of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salt, trading oil greasy spots etc on old decorated surfaces of wall and applying two coats of oil bound distemper of approved shade/tint and inclucluding 1 mm thick Birla white wall care putty complete all as specified and directed.

M & L for brooming down old decorated surfaces of walls, plastered or unplastered including cornices, plasters etc and applying one coats of white wash complete all as specified and directed.

All as per description of serial item No.51.00 here-in-above but on ceiling surfaces complete all as specified and directed.

S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floorcomplete all as specified and directed.

S&F 20mm GI tubing Medium grade fix to wall/floor complete all as specified and directed.

S&F in repair PVC connection pipe, 15mm dia & 600mm long with adopter and washer at both end complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks of 1000 Ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F in repair ball valves brass high pressure with polythelene float and fly net complete, screwed , iron pipes 15 mm dia complete all as specified and directed.

S&F in repair fancy type bib taps, chromium plated alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule and fixed bore in dia 15mm complete all as specified and directed.

S&F white vitreous china under counter basin size 450x525x195 mm shape oval of jaquar/cera or equivalent incl 32mm dia CP waste coupling complete all as specified and directed.

S&F in repair Stop/angle valves,fancy type, chromium plated alloy screwed down high presure, screwed both ends for iron pipe or for unions of 15 mm dia complete all as specified and directed.

S&F in repair 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm bore swan neck cast copper alloy chromium plated pillar tap weight not less than 400gms screwed for iron pipe or brass ferrule fixed complete all as specified and directed.

S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging; also fastening & fixing complete GDE Fe410-0 or E-250.

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S& F in repair Vitreous China Squatting pan, Orissa pattern, size 580 x 440mm white with integral foot rests connection to trap and to flushing pipe, etc.complete including making food to floor complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device fixed complete all as specified and directed.

S&F in repairs PVC low level flushing cistern 10 litrs capacity (white ISI marked) with inlet ball valve, float and handle, syphonic action type including brackets and flush pipe of polythelene of low or high density of PVC 32mm dia for LLFC make Dolfine/Commander Champion, fixed in repairs, complete all as specified and directed.

S&F in repairs Vitreous China urinals, half stall type, complete including providing and fixing plus, bedding urinal against wall in cement mortar 1:2 securing urinal to plus with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe complete all as specified and directed. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S&F in repair Tubular towel rail, 20mm dia, D type, 60cm long between flanges of Brass chromium plated complete all as specified and directed.

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls complete .

S&F PVC (SWR) bends any radius 110 mm bore complete all as specified and directed.

S&F in repair Grating doom 100 mm dia of PTMT (Minimum weight 25 gms) fixed with cement complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR),110mm junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including removing the old pipes and making good the disturbed surface as per existing complete all as specified and directed.

Demolition Mud/PCC in roofs padding any thicknes, including plastering , existing tretement and cleaning (whether full thickness removed or only or part there of) etc in all respect and preparing it for further treatment and taking out and disposal of debris & rubbish to a distance exc 1 Km but not exc 1.5 Km complete all as specified and directed.

M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over roof complete all as specified and directed.

M&L rendering laid 15mm thick in CM 1:4 with water proofing compound over green concrete surface(WPC will be measured and paid seperately) surface finished even and smooth (without using extra lime or cement) complete all as specified and directed.

M&L Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq. m including cleaning surfaces over bituminious primer complete all as specified and directed.

M&L APP based plymeric membrane minimum weighing 3 Kg/Sqm and minimum 3 mm thick reinforced with polyster non woven reinforcement/mat (center core) with thermal insulation laid by toarch application method with overlaps 100mm on length side and 100mm on the width side as per manufacture,s instructions with fabric (wt not less than 150 gms/sqm) on primed surface including two coat of refelective silver aluminium paint over APP membrane complete all as specified and directed.

Cutting holes in brick walls Exc half brick but not exc one brick built in cement mortar or cement lime mortar and stone walls built in lime mortar etc for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B1 as required complete all as specified and directed.

Demolition of Roofs, floors (other than ground floors), beams staircases, landing, chajjas, & similar suspended work Cement concrete (reinforced) complete.

M&L RCC (nominal mix) type B1 (1:2:4) using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L RCC (nominal mix) type B1 (1:2:4) using 20 mm graded aggregate in chajjas and the like complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

S & F mild steel cupboard shutter with frame, Godrej pattern made out of 22 guage mild steel sheet including chromium plated MS handle with proper locking arrangement (brass mortice lock vertical type size 65mm 4 lever with escutcheon plates & two keys) with & including two coats of spray painting with synthetic enamel paint of approved tint over a coat of red oxide primer including fixing with 6 Nos 12 mm dia bolt 150mm long grouted in brick wall/concrete including making good the disturbed surface as original complete all as specified and as directed. Note :- The measurement shall be taken of front elevation and not girthwise.

M&L for Granite (of any type) tiles 18- 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and over screed bed 20 mm thick CM 1:6 cement concrete complete all as specified and directed.

M & L for 18-20 mm thick Granite (of any type) tiles machine cut, in skirting/dado laid over cement screed and jointing with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing including 10mm thick rendering in CM 1:4 for recieving stone etc complete all as specified and directed.

S&F in repair chromium plated health faucet for EWC with including PVC Connection 1m long suitable for 15mm bore with all connected fittings complete all as specified and directed.

S&F in repairs brass chromium plated shower rose 65mm size with swivel joint type including shower arm fixing to steel pipe of 15mm bore or union complete all as specified and directed.

S & F in repair Plain 4mm mild steel wire in detached work such as for mosquito nets and fixing to straining bolts, hooks, eyes, etc complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings & similar work; not exc. 200mm thick (Horizontal or sloping) Rough finished surfaces of concrete flat complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor & roofs n exc 20 cm wide & sides of RCC/PCC bands in walls, horizintal or sloping & similar work exc 10cm but n exc 20cm wide Roughed finished surface of concrete complete all as specified and directed.

M&L washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 pigmented stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and directed. (Payment for providing grooves shall be made separately).

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden attens, repair to the edges of panels and finishing the groove complete all as specified and directed.

Treatment for sunken portion is as follows:- M&L for water proofing treatment in sunken floors as described hereunder:- 1) Demelotion of lean concrete and other type of filling in sunken portion & cleaned the sunken portion incl vertical wall surface complete as directed. 2) PCC (1:2:4) type B0, covered filling in sunken portion 75mm thickness shall be provided at the junctions of RCC slab and adjoining walls. 3) Sunken floor and sides upto finished floor level shall be plastered with 15mm thick plaster in CM 1:4 wixed with WPC@ 3% by weight of cement. 4) Applying bitumen primer of sunken floor & side surfaces TANKMASTIC of M/s STP Ltd @ 0.40 ltr/Sqm. 5) Sunken portion shall be filled with lean concrete (1:5:10), Type E-2 using 40mm aggregate after carring out of satisfactory testing of CIpipes/Joints & Slab/walls by filling water 72 hrs. The sunken portion of Nahani trap/floor trap and pipes, joints shall be emmbeded in PCC (1:3:6) blocks 6) GI Spout pipe 32mm dia and 450mm long cross cutted ends shall be inserted at the time of repair to Sunken portion as directed. Note:- i) In case any defect is noticed the portion shall be grouted with cement slurry mixed with suitable chemical & tested again. This process of grouting and testing shall be repeated till leakage/seapage/dampness is elimaneted ii) Horizontal flat area only measured. iii) Above aspets are deemed to be included in quoted rate.

Taking down carefully copper/aluminium point wiring (light, socket or power) complete (fittings such as switches, ceiling roses, pendants, regulatos, sockets etc to be measured separately), and making good disturbed surfaces of walls, floors etc to match with existing surfaces.

M&L for concealed Point wiring for One Light point controlled by one, one way switch with two single core PVC insulate, unsheathed multistranded copper conductor cable of size 1.5 sq.mm (FRLS) drawn in and including electrical grade PVC conduit 20 mm dia concealed on wall/ceiling/floor including PVC insulated unsheathed earth wire with multi stranded copper conductor of size 1.5 sq.mm(FRLS) including MS shunk sheet metal box with modular sheet top cover of required module with frame for mounting switches, sockets etc complete all as specified. Note -(a) Quoted rates shall be deemed to include the cost of Cutting Chases in Stone/Brick wall and making good to the disturbed surfaces including plastering and painting to match with the existing colour. (b) The rates Quoted by the contractor shall be deemed to include the cost of modular cover plates of required module with frame, cost of Sheet Metal Box and no additional payment shall be made on account of the same.

All as per srl item No 100.00 but for One ceiling/exhaust fan point controlled by one switch and regulator

All as per srl item No 100.00 but for One 3 pin switch socket outlet, 5 Amp on the same board with other switches.

All as per srl item No 100.00 but for One 3 pin 5 amps switch socket outlet point on independent board.

All as per srl item No 100.00 but for One bell/buzzer point controlled by one bell push.

All as per srl item No 100.00 but for Two way point controlled by two way switch.

All as per srl item No 100.00 but for wiring with 4 sq.mm multistranded cable and earth wire with copper conductor of size 4 sq.mm for 15 amps power point.

Supply and fixing Modular switch, one way 6 Amp, 1 module, piano type, 230/250 volts grade on top covers (catered in point wiring above).

All as per srl item No 107.00 but for Modular switch, two way 6 Amp, 1 module

All as per srl item No 107.00 but for Modular switch, one way 16 Amp, 1 module

All as per srl item No 107.00 but for Modular bell push 6 Amp, 1 module

Supply and fix Modular socket outlet 2in1, 3pin 5A, 2 module multipurpose use, flush mounting type, 230/250 Volts grade on Top covers (catered in point wiring above).

All as per srl item No 111.00 but for Modular socket outlet 2in1, 3 pin 15 Amps flush type

Supply and fix LED batten (1.2m) made of CRCA sheet housing with a PC glossy diffisure duly prewired connection having nominal system lumen output of 2000 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 20 watt including driver. it should have rated system life time of 40000 burning hours at L70 and should have a temperature of 6500 K CRI >80, thd <10 and PF>0.95 complete all as specified and directed make - Crompton Cat Part CIS-305-40-57-SL-DP-NWH, Philips Cat part BN308C LED20S-6500 L120 PSU WH, Havells Cat Part STOUTPLUS600BS20WLED840SPCWH

Supply and fix lamp holder insulated body with back plate for angle/batten fitting with LED of 09 watt complete all as specified and as directed.

Supply and Fixing 20 watt emergency LED inverter bulb B-22 capacity with inbuilt powerful lithium battery backup of atleast 4 hours and having minimum two years warranty. The lighting shall have deep discharge protection, fast charging, offering cool day light for atleast four hours in off hours. Make : - Havells/Philips/Bajaj

Supply and fixing in replacement LED Bulkhead fitting 1 x 10 Watt, complete with Standard LED lighting fixture with extruded polycarbonate housing environment friendly, including electric connection with using 2 core flexible copper conductor cable 23/0.00076 from ceiling rose to light fitting, complete fitting with all accessories and following specifications complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 5°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : <15%. (f) IP rating : IP-65. (g) CCT : Minimum 5400K (h) Polycarbonate housing white coloured (j) LED Driver of the same make as of the luminaire. (k) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (l) Surge protection minimum 2.5 kV. (m) CRI : Minimum 80 (n) Rated life time : 50000 burning hrs @L70 (Average 10 to 12 hrs daily)

Supply and fixing in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-In-Charge

Supply and fix ceiling rose surface bakelite two to three terminals/plate 5 amps.

Supply and fix sheet metal enclosure DB single pole and neutral for 240 volts 8 way with 200 Amps rated busbar flush/surface mounting double door including wooden board.

Supply and fix Vertical MC DB distribution box 3 phase TPN 4 ways double door including MCCB 125 Amp 16 KA as incommer with bus bar rating 200 Amps vertical type dust and vermin proof complete all as specified and as directed.

Supply and fix MCB single pole 240 volt 6-32 amps 10 KA, complete all as specified and as directed.

Supply and fix MCB SPN 240 volt 32 amp 10KA complete all as specified and as directed.

S&F sub main wiring on and including passing through PVC conduit in concealed (including cutting chasis in stone/brick wall) 1100 Volts grade with PVC flexible cable copper conductor cable fire resistant low smoke and halogen (FRLSH) unsheathed multistranded single core of size 6 sqmm and continuous earth with PVC flexible cable copper conductor unsheathed multistranded single core of size 6 sqmm of green colour confirming to IS 694/1990 including taking down existing U/S sub main wiring. (Note: Two runs of cable with one run of earth wire and one run of PVC Coundit should measured as one length)

Earthing complete with galvanised steel earth plate electrode 600mmx600mmx6 mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level connected to GI wire 4mm dia by means of bolts, nuts, check nuts and washers complete including earthing pit, Chemical compound, GI wire 4mm dia up to 7.5 m, 20 mm dia medium grade GI watering pipe, G.I. protection pipe 40mm dia eath pit in PCC 1:2:4 type B-1 using 20 mm graded stone agggragate RCC pit cover including earth work complete all as shown electrical palte No-3 of SSR-2009 (Part-I) NOTE:- The unit rate shall include for excavation & earth work in any type of soil/strata, PCC 1:2:4 type B-I for pit & RCC 1:2:4 type B-I for cover with 8mm dia CTD Bar @150mm C/C both way, funnel with watering pipe 20 mm dia medium grade, 15mm dia light grade GI pipe up to 7.5 mtr long, wiremesh complete all as specified and directed.

S&F sheat metal incl single pole and neutal with 02 Pin and earth plug and socket complete with 01 single pole 20 Amps 240volts, MCB complete incl necessary fixing arrangement and all incoming and outgoing electric connection all as specified as directed by Engr-in-Charge.

Supply and fixing in replacement energy efficient LED street light fitting of 45W pressure die cast aluminium housing/body, heat resistant clear toughened glass, better optics for uniform distribution street/Roadway luminaire, with driver, including electric connection, fixing the light fitting with new bracket made out of GI tubing light grade 32mm dia, 1.2 metre long bent to shape at 120 degree angle at half metre from bottom, including two Nos clamps made out of MS Flat iron size 40x3 mm with suitable nuts and bolts for fixing of bracket including painting to MS clamp and nut bolts with two coats of aluminium paint over a coat of red oxide primer, complete fitting with all accessories and following specifications, including taking down old Unserviceable light fitting with old bracket any type complete all as specified and directed by Engineer-in-Charge :- (a) Lumen system efficacy of luminaire should be minimum 100 Lumen per watt. (b) Input Voltage range : 140 to 270 volts (c) Temp operating range : Minus 10°C to Plus 50°C (d) Power factor : Minimum 0.95 (e) THD : Max10%. (f) IP rating : IP66. (g) IK rating : Minimum IK07 (h) Built in potted LED Driver of the same make as of the luminaire. (j) LED driver should be complete with all protections viz open/short circuit protection, over voltage protection, all as per standard design of manufacturer. (k) Surge protection 10 kV (inbuilt + extended) (l) CCT : 5700 K. (m) CRI : Morethan 80 (n) Lens - High Efficiency wide angle lens. (o) BIS Approved fixtures and driver (p) Rated life time : 50000 burning hrs (Average 10 to 12 hrs daily)

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable with aluminium stranded conductor 1100 Volt grade cross sectional area 25 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/ along poles etc complete all as specified & directed. Note : Sand cushioning, cable protection, GI protection pipe, clamps, jointing kits and excavation & earth work shall be measured & paid for separately.

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying of cables, pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil.

Returning, filling in, including spreading, leveling watering and well ramming in layers not exc 25 cm thick in soft/loose soil.

Removal of excavated soil/ material to a distance not exc 50 metre and depositing where directed at a level not exc 1.50 metre above the starting point complete all as specified.

M/L for brick work with FLY ASH BRICKS(As Per IS-13757(1993) burnt clay fly ash building bricks), (OLD SIZE BRICKS) laid dry & flat abutted with each other with gap between adjacent bricks not exc 10 mm over UG cable for protection and complete all as specified & directed.

M&L for dry sand and punning for cushioning to under ground cable all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

Disconnecting form elect connection and taking down carefully the existing Ceiling fan/Exhaust fan/Geyser of any capacity, any make,any size and depositing the same Ceiling fan/Exhaust fan/Geyser in AGE E/M store yard all as specified and directed by the Engineer-in-Charge.Refixing the same Ceiling fan/Exhaust fan/Geyser carefully including necessary repair work for making functional the same and making electric connections complete all as specified and as directed. Note : Rates quoted by the contractor shall be deemed to include the cost of minor repair work of Ceiling Fan, Exhaust Fan and Geyser like replacement of Capacitor, bearing, fan rod etc in case of Ceiling Fan/Exhaust Fan if found unserviceable and replacement of thermostate in case of Geyser etc.

M/L for GI pipe ( Light grade ) for protection of LT cable fixed to walls/ poles/road crossing including clamps complete of 40 mm bore

Supply & install, testing & commissioning in repairs LT control panel compartmental type,Lockable fabrication with dimension 1200(H)x 500(W)x 500(D) made by 3.15 mm thick sheet CRCA approved weather proof design framed on angle iron (40mmx40mmx6mm) double door front and rear openable both side opening shutters duly painted two coat with siemens gray color, cable entry with glands, foundation /grouting on & including PCC as per site requirement with the following :- (a) Al bus bar 150 Amp Cap- 1 Set ( Set of 4 strips) (b) MCCB 125 Amp 4 Pole 25 KA - 1 No (incoming) (c) MCCB 63 Amp,4 Pole,16 KA with spreader links - 2 Nos(Outgoing) (d) indicating Lamp LED type R,Y,B - 3 Nos (e) Control fuse - 3 Nos

Supply and fixing in repair of 25 mm bore GI water tubing IS-1239 marked, medium grade, in replacement including all necessary pipe fittings laid in trenches, on wall, under floor, under road on same or new route and making good the disturbed portion as existing and including taking down of old unserviciable pipe complete all as specified and directed. Note :-Excavation and Earth work will be measured and paid separately

M & L for Gun-metal, globe or gate valves, 25 mm bore of pipe with iron wheel head, screwed both ends with GI Union for iron pipe and fixed complete all as specified and directed.