REPAIR TO WATER PROOFING TREATMENT RCC ROOF SLAB REPLACEMENT OF GALVALUME ROOF SHEET FALSE CEILING AND ALLIED WORKS AND JOINERY, PLUMBING AND OTHER B R REPAIR WORKS AT KALIMPONG MIL STN UNDER GE 867 EWS

Amount

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good in PCC (1:2:4) type B1 or cement mortar (1:4) (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt.after fixing new frame complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exceeding 1.5 Sqm and not exceeding 4 sqm each, including cutting holes for taking out hold fasts or dismantling brick work and making good in PCC (1:2:4) type B1 or cement mortar (1:4) (holes cut and any other damage to jambs, walls for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt. after fixing new frame complete all as specified and as directed.

Taking down shutters of any description area exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and as directed.

Taking down shutters of any description area not exceeding 1 Sqm each complete all as specified and as directed.

Taking down shutters of any description area exceeding 1 Sqm but not exceeding 2 Sqm each easing and refixing in same opening complete all as specified and as directed.

S&F second class hardwood plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid ,rounded or chamfered put together with glue pinned joints all as specified and directed. TIMBER: - Sal/Kalasiris/Chaplash/Hollock/Bijasal

S&F 105x60 mm size pressed steel door frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., including PCC (1:3:6) type C0 filling complete all as directed by Engr-in-Charge.Make: - DIWAN STEELS/AVA/AJANTA or equivalent as approved by GE.

S&F 125x60 mm size pressed steel door frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., including PCC (1:3:6) type C0 filling complete all as directed by Engr-in-Charge. Make: - DIWAN STEELS/AVA/AJANTA or equivalent as approved by GE.

S&F 35mm thick 2nd class hard wood plain framed panelled shutters (any number of panels) with panels of 12mm thick timber flat on both sides or of 12mm thick veneered particle board ,medium density, wood particle board with commercial face veneers with sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats complete all as specified directed by Engr-in-charge.

S&F 35 mm thick second class hard wood Glazed and skeleton shutters for doors, open rebated and prepared to receive glass, gauze etc., with out sash bars, edges of framing plain, chamferred or rounded, fitted with cut and mitred beads for securing glass, wire gauge etc. ; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats all as specified and directed.

S&F 30 mm thick second class hard wood Glazed and skeleton shutters, for windows and ventilators, open rebated and prepared to receive glass,gauze etc. divided in to squares, with plain chamfered or rounded, mitred and rebated sash bars, any numbers, edges of framing plain, chamferred or rounded, fitted with cut and mitred beads for securing glass, wire gauge etc. ; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (b) fitted to chowkats all as specified and directed.

S&F factory made PVC Solid Door frame of size 50mmx47mm made out of 5mm plain coloured PVC sheet reinforced with MS Square tube, fixed in opening as per specification and dawings.

S&F Factory made Solid panel PVC Door Shutter of 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colourr PVC 'C' channel having a PVC sheet strip 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of plain clour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beeding and jointed together with solvent cement as per specification and drawing.

S&F steel window with side hung shutters (glazed or wire mesh shutters) fitted with box type hinges with suitable MS handles, peg stays, with glazing bars for receiving glass / MS flat for receiving wire mesh including taking down existing windows and making good jambs after fixing new window complete all as directed by Engr-in-charge.

S&F steel window with side hung shutters (glazed or wire mesh shutters) fitted with box type hinges with suitable MS handles, peg stays, without glazing bars taking down existing windows and making good jambs after fixing new window complete all as directed by Engr-in-charge.

S&F steel ventilators with top hung shutters (glazed or wire mesh shutters) fitted with box type hinges with suitable MS handles, peg stays taking down existing windows and making good jambs after fixing new window complete all as directed by Engr-in-charge.

S&F steel windows or ventilators with fixed type with glazing bars taking down existing windows and making good jambs after fixing new window complete all as directed by Engr-in-charge.

M&L Mild steel work such as bands, straps, clamps and hold fasts etc. of Fe-290 Gde E-165 all as specified and directed.

S&F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beeds all as specified and directed.

S&F in repairs, Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples or wooden beeds all as specified and directed.

Hacking out old broken glass and S & F 3 mm thick sheet glass ordinary quality fixed with oil putty and necessary clips/nut bolts area not exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge.

S&F 3 mm thick sheet glass ordinary quality fixed with oil putty and necessary clips/nut bolts area not exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge.

S&F 4 mm thick figured glass pin head type fixed with oil putty and necessary clips/nut bolts area not exceeding 0.5Sqm in each pane complete all as directed by Engr-in-Charge.

S&F Mild steel works as in grills, framed guard bars, and similar works conforming to F2 290, Gde E-165 all as specified and directed.

S&F 100 mm size mild steel cold rolled medium weight butt hinges complete all as specified and directed.

S&F 75 mm size mild steel cold rolled medium weight butt hinges complete all as specified and directed.

S&F of continuous (piano) hinges mild steel bright finish or electro galvanised 30 mm width of flaps complete all as specified and directed.

S&F 150 mm long Aluminium anodised barrel tower bolts of extruded aluminium section all as specified and directed.

S&F 200 mm long Aluminium anodised barrel tower bolts of extruded aluminium section all as specified and directed.

S&F 150 mm long Aluminium alloy handles cast type anodised all as specified and directed.

S&F 300mm long aluminium alloy anodised sliding door bolts with hasp & staple (bolt type) and fixing clip of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and directed.

M&L for 18/19 mm thick Block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face, all as specified and directed.

M&L for external teak wood lipping, 6mm thick fixed with nails for 19 mm thick Prelaminated particle board faces all as specified and directed.

M&L for 12 mm thick plywood , grade BWR type BB, fixed with scews to timber frame work complete all as specified and directed.

M&L external teak wood lipping, 6 mm thick on exposed surface for 12 mm thick prelaminated particle board fixed with nails complete all as specified and directed

M&L Preparing new or previously un treated surfaces of wood and wood based surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and directed.

M&L preparing new or previously untreated surfaces of steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails all as specified and directed by Engr-in-Charge

M & L for Weather boarding ( Hardwood 2nd class), clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm lap complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing rubbish off the complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar (1:6) or with chemical tile adhisive (SIKA) complete all as specified and directed by Engr-in-charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, on vertical surfaces such as skirting/dado, jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 10mm thick rendering in cement mortar (1:4) or with chemical tile adhisive (SIKA) complete all as specified and directed by Engr-in-charge.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick square/rectangular area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc., jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid on and including 15mm thick screed bed in cement mortar (1:6) or with chemical tile adhisive (SIKA) complete all as specified and directed by Engr-in-charge.

M&L Glazed ceramic coloured tiles size 350x 250x 7 mm/ 450x300mm/450X 350X 7mm thick setas in vertical surface such as risers of steps, skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile over and including 15 mm thick rendering in CM (1:4) finished even and rough complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick premium quality conforming to relevant IS (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces of tile over and including 20 mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

M&L for 17 to 20mm thick Granite slab of any type and colour machine cut in steps, jambs, pillars, window cills, cooking platform etc., bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, polishing and rounding exposed edges complete laid over and including 20 mm thick rendering in cement mortar (1:6) including dismantling existing stone slabs and removing rubbish off the premises complete all as specified and directed by Engr-in-charge.

Taking up or down 15 mm bore old steel tubing and connections, including disconnection of fittings from tubing including cleaning for re-fixing or removal from site complete all as specified and directed.

S&F 15 mm bore GI water tubing medium grade with all fittings and fixed to wall, floor, ceiling complete including short lengths including taking down existing GI pipe all as specified and as directed by Engr-in-charge. Make: TATA/JINDAL/ZENITH

Cutting chases, plainning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, sillls, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good cutting not exc 10 cm girth in brick walls built in cement mortar complete all as directed by Engr-in-Charge.

M&L for 20 mm outer dia CPVC pipes SDR 11 with and including CPVC SDR 11 fittings siutable for plumbing fittings on walls/ceiling or laying in floors complete all as specified and directed.

Taking down existing IWC along with its cement concrete bedding and P or S trap and S&F Orrissa pattern vitreous china squatting pan white colour of size 580x440mm with integral footrest (Excluding flushing cistern and flush pipes) but including cement concrete bedding and P or S trap as required including PVC pipe upto finished floor level to connect flush pipe, making good all the disturbed surfaces of floor to match the adjoining complete all as directed by Engineer-in-Charge.

S&F PVC valveless, symphonic action type, flushing cistern 10ltr capacity, low level, white with inlet ball valve float and handle along with suitable flush pipe/bend including brackets fixed in repairs complete all as directed by Engr-in-Charge.

S&F Vitreous China wash basin, white, flat back, of size 550 x 400 mm, excluding taps, waste chain and plug and porcelain stopper but including brackets and 32mm dia PTMTwaste fitting, including taking down existing unserviceable/broken wash hand basin all as specified and directed by Engr-in-Charge.

S&F in repairs of 1mm thick stainless steel sink with drainage board kitchen or laboratory type with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size of sink 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs of 1mm thick stainless steel sink kitchen or laboratory type with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size of sink 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair Brass chromium plated shower rose with or without swivel joints 125 mm size , including fixing to steel pipe or unioncomplete all as specified and directed.

S&F in repairs PVC connection pipe 15mm dia, 450mm long with PTMT check nuts and washer on both ends complete all as directed by Engr-in-Charge.

S&F in repairs Stop/angle valves 15 mm bore, cast copper alloy chromium plated screwed down high pressure, with crown or capstan head, concealed type with long shank ang cup screwed both ends for iron pipe or for unions all as specified and directed by Engr-in-Charge.

S&F in repairs bib taps 15 mm bore, cast copper alloy chromium plated screwed down high pressure, fancy type with crown or capstan head, screwed for iron pipe all as specified and directed by Engr-in-Charge.

S&F for pillar taps, 15mm bore, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs kitchen plate rack made out of stainless steel 1.00 mm thick sheet with partitions and size of rack 800 x 250 x 900 mm with shape and pattern as per sample kept in Sample room of GE Office complete all as specified and directed.

S&F in repairs central hole basin mixer without popup waste brass chromium plated CP complete all as specified and directed Make:-HINDWARE Cat No. F720014 or equivalent in JAQUAR/ESSCO (DELUX)

Demolition and breaking up old broken , PVC (SWR) , Cast Iron, AC, SWG soil waste and vent pipe of 75/100/110 mm bore including accessories set in cement mortar and removing rubbish from site as directed by Engineer-in-Charge complete all as specified and directed.

S&F of 110 mm PVC (SWR) drain pipe single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75 mm PVC (SWR) drain pipe single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F of 110 X 75 mm bore PVC (SWR) reducer including jointing with solvent cement complete all as specified and directed.

S & F of 110mm bore PVC (SWR) bends complete all as specified and directed by Engr - In- Charge.

S & F of 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed by Engr - In- Charge.

S & F of 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed by Engr - In- Charge.

S&F 100mm Size hasp & staple, safety type, aluminium alloy anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F multi purpose self adhesive elostomeric bituminus sealing tape, laminated with an aluminium film on the upper side with and including preparation of roof top surfaces by wire brush and applying the tape as per manufacturers instructions.

Dismantling of plain or corrugated steel sheeting, any gauge and thickness including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating (AZ-70) GI based steel sheet of approved profile of corrugation, 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws all as specified and directed by Engr-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating (AZ-70) GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, eaves board, ridges, hips,valley gutters, drip and straight flashing cladding to wall etc, fixed with self tapping screws all as specified and directed by Engr-in-Charge.

M & L for Galvanised, 0.63 mm thick ,corrugated mild steel sheeting with two corrugations side lap,fixed with L-type or J-type or cranked hook bolts in lieu of screws with grade of zinc coating 275 complete all as specified and directed.

M & L for Plain, 0.63 mm thick, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 completed all as specifed and directed.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed.

Dismantling timber scantlings 40 Sqcm and over in section, in any position (framed work) all as specified and directed.

Dismantling timber fillets, rails, posts rafters purlins etc under 40 Sqcm in section fixed in any position (Unframed work) complete all as specified and directed.

S&F false ceiling with powder coated exposed GI grid suspension system (E-Grid T-2430 or equvalent load carrying capacity with mid span deflection not exc. 1/360 span with hanger spacing of 1200mm c/c) consisting of main runner 3600mm long, cross Tee 1200mm/600mm long and wall angle. The main runners to be placed @ 1200mm, the cross Tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600mm to form a modular grid of 1200mmX600mm. Additional cross Tees of 600mm shall be placed perpendicular to the cross tee 1200mm long to finally form a grid of 600mmX600mm. Suspensor system (Grid) made out of GI sheet main Tee of size 23.5mmx38.50mmX0.36mm and cross Tee of size 23.5mmX23.5mmX0.36mm and angle size 19mmx19mmX0.36 mm. Grid of modular size 600mmX600mm shall be supported by 4 mm dia G.I. wire from purlins/soffit with and including 4mm thick high pressure steam cured non asbestos fiber cement designer ceiling board (Density>1200Kg/Cum) of size 595mmX595mm, confirming IS 14862 & Type B Category III of ISO 8336, tested as per AS 1530 part 3 & BS-476 Part 4, 5, 6, 7 & 8, complete all as per manufacturer's instruction. (Make : Everest or equvalent as approved by GE)

S&F cold rolled mild steel sections such as joist, channel, angle, flat iron or Tee sections, fixed independently with connecting plates, etc confirming to Fe 410-W (Gde 250 quality A) complete all as specified and directed.

Demolition of brick work or stone/boulder masonary, built in cement mortar including all quions, arches, pillars etc, but excluding ashler facings, dressed stone work and precast concrete articles.

M&L for brick work with sub class 'B' bricks , using old size bricks, straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) complete all as specified and directed.

M & L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in Cement mortar (1:4) complete all as specifed and directed.

Taking down cement plaster on brick or stone masonry surfaces of walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete sur face, rendering finished even and smooth (without using extra cement) complete complete all as specified and directed.

M&L 15 mm thick (in two coats of 10mm+5mm) rendering on fair faces of brick work or concrete surface in cement mortar (1:4) on external wall finished even and fair mixed with integral water proofing compound @ 2% by weight of cement or in the manner specified by the manufacturer and in the proportions indicated all as specified and as directed.Note:-WPC will be measured and paid separately as supply only.

Supply only integral water proofing compond all as specified and as directed.

M & L for rendering 5 mm thick on fair faces of brick work or concrete surfaces in Cement mortar (1:3) on surfaces of ceiling , finished fair and even complete all as specified and directed by Engr-in -charge

M&L for two coats of oil bound distemper over a coat of priming coat on newly prepared wall surfaces, including 1 mm thick wall care putty in two coats (Birla white or equivalent) all as specified and directed.

M&L for preparation on newly plastered / previously untreated surfaces of wall for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for preparation on newly plastered / previously untreated surfaces of ceiling and appling three coat of white wash as in ceilling , complete all as specified and directed.

M&L for machine cut Kota stone slab flooring, 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing and exposed edges of Kota stone shall be rounded complete over and including 20 mm thick screed bed or bedding layer in CM (1:4) finished even and rough all as specified and directed.

M&L for machine cut Kota stone slab as in vertical surfaces such as dado/skirting, 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing and exposed edges of Kota stone shall be rounded complete over and including 10 mm thick rendering in CM (1:3) finished even and rough all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of walls and applying three coats of white wash on walls complete all as specified and directed.

M&L for PCC (1:3:6) type C-1 (using 20 mm graded crushed stone aggregate) as in bed blocks for grouting hold fasts , coping, filling in pressed steel chowkat or similar work including necessary form work as required complete all as specified and directed.

M&L preparation of old steel surfaces of any description over 10 cm width or girth not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M & L for 50 mm thick Cement concrete (1:2:4), type B-0 (using 12.5mm graded aggregate) placed in any position as in padding complete all as specified and directed.

M&L 3mm thick Atactic polypropylene polymer (APP) based polymeric membrane minimum weighing 3.6kg/sqm and reinforced with polyester non woven fabric (weight not less than 150 gm/sqm) laid over a coat of bitumen primer @0.40L/Sqm by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS, The membrane shall be laid with 100mm side overlap and 150mm end overlap, fixed using butane torch and sealing all joints etc after preparing the surface as per standard practice and as per manufacturer instructions and finished with applying one coat of bituminous aluminium paint @100gm/sqm on top of membrane, complete all as specified & directed.

M & L for first layer of slurry of cement at the rate of 0.488 kg/Sqm mixed with acrylic based polymer modified cementitous composite compound at the rate of 0.253 kg/Sqm this layer will be allowed to air cure for 4 hours , second layer of slurry of cement at the rate of 0.242 kg/Sqm mixed with acrylic based polymer modified cementitious composite compound at the rate of 0.126 kg/Sqm this layer will be allowed to air cure for 4 hours followed with water curing for 48 hours including 200 micron thick polythene film pasted with the help of adhesive shall be provided over above treatment , Note - The rate includes preparation of surface, treatment and seling of all joint, corners, junction of pipes and masonary within polymer mixed slurry, This treatment shall be provided after provision of cement plaster mixied with WP compound and synthetic fibers while concerte is still green complete all as specified and directed by Engr-in -charge : Make STP /Dr fixit sunken treatment / pedilite eqavalent . Note : Payment will be done fo plane area only.

Note: In case doubling/duplicancy of BOQ items , the lowest quoted rate shall be applicable for payment.

RAJU TAMANG (BID ID -3166744)

G K SUTHAR (BID ID -3166749)

SUNIL PRADHAN (BID ID -3166761)

MANOJ JINDAL (BID ID -3166773)

PRASAD PRADHAN AND SON (BID ID -3166766)

DEEP CHANDRA JOSHI (BID ID -3166775)

HEM RAJ GURUNG (BID ID -3166781)

ANTHONY PRADHAN (BID ID -3166782)