Special repair to LT overhead to underground cables, Provn of Desert Coolers, Deep Freezers, Humidity control devices (AC) and servo stablizer under GE(Utility) Udhampur

Amount

Supply, install, testing and commissioning and testing factory made and tested CPRI type test certified) LT feeder pillar box (KIOSK) out door type, floor mounted,compertmantalised suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, dust and vermin proof, made of 3.15mm CRCA MS sheet with digital Volt meter, Ammeter, with CTs ,Led lamps RYB for all incomers & outgoings MCCBs are to busbar spadles to fitted complete base frame of 50x50x6mm angle iron , powder coated, having front and rear openeable hinged double door shutters with aprons for cable entry and locking arrangement complete with following :- Incoming:- (a) MCCB 200 A 4 pole, with thermal adjustable and fixed magnetic setting with extended 50Hz ,415 V with rupturing capacity 35 KA-01 No,

Outgoing:- (a) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 300 Amp,4 pole, not less than 75 cm long mounted on insulators 01 set. Note- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands. (v) including suitable thimbles/lugs, nut bolts ,washers fitted the cables. (v) cable glands for incoming and out going suitable cables is including rate quated by vendover.

Supply, install, testing and commissioning and testing factory made and tested CPRI type test certified) LT feeder pillar box (KIOSK) out door type, floor mounted,compertmantalised suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, dust and vermin proof, made of 3.15mm CRCA MS sheet with digital Volt meter, Ammeter, with CTs ,Led lamps RYB for all incomers & outgoings MCCBs are to busbar spadles to fitted complete base frame of 50x50x6mm angle iron , powder coated, having front and rear openeable hinged double door shutters with aprons for cable entry and locking arrangement complete with following :- Incoming:- (a) MCCB 160 A 4 pole, with thermal adjustable and fixed magnetic setting with extended 50Hz ,415 V with rupturing capacity 35 KA-01 No.

Outgoing:- (a) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 240 Amp,4 pole, not less than 75 cm long mounted on insulators 01 set. Note- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands. (v) including suitable thimbles/lugs, nut bolts ,washers fitted the cables. (v) cable glands for incoming and out going suitable cables is including rate quated by vendover.

Supply, install, testing and commissioning and testing factory made and tested CPRI type test certified) LT feeder pillar box (KIOSK) out door type, floor mounted,compertmantalised suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, dust and vermin proof, made of 3.15mm CRCA MS sheet with digital Volt meter, Ammeter, with CTs ,Led lamps RYB for all incomers & outgoings MCCBs are to busbar spadles to fitted complete base frame of 50x50x6mm angle iron , powder coated, having front and rear openeable hinged double door shutters with aprons for cable entry and locking arrangement complete with following :- Incoming:- ( a) MCCB 100 A 4 pole ,Ics=100%Icu- 25/26 KA, 415 Volts, with thermal adjustable and fixed magnetic setting with extended terminals -01 No.

Outgoing:- (a) Bus bar electrolytic grade copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 150 Amp,4 pole, not less than 50 cm long mounted on insulators 01 set. Note- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands. (v) including suitable thimbles/lugs, nut bolts ,washers fitted the cables. (v) cable glands for incoming and out going suitable cables is including rate quated by vendover.

Supply, install, testing and commissioning and testing factory made and tested CPRI type test certified) LT feeder pillar box (KIOSK) out door type, floor mounted,compertmantalised suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, dust and vermin proof, made of 3.15mm CRCA MS sheet with digital Volt meter, Ammeter, with CTs ,Led lamps RYB for all incomers & outgoings MCCBs are to busbar spadles to fitted complete base frame of 50x50x6mm angle iron , powder coated, having front and rear openeable hinged double door shutters with aprons for cable entry and locking arrangement complete with following :- Incoming:- ( a) MCCB TPN 100 Amps 415 Volts 35 KA, with thermal adjustable and fixed magnetic setting with extended terminals -01 No.

Outgoing:- (a) Bus bar electrolytic grade Copper and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 100 Amp,4 pole, not less than 50 cm long mounted on insulators 01 set. Note- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands. (v) including suitable thimbles/lugs, nut bolts ,washers fitted the cables. (v) cable glands for incoming and out going suitable cables is including rate quated by vendover.

Supply, install, testing and commissioning and testing factory made and tested CPRI type test certified) LT feeder pillar box (KIOSK) out door type, floor mounted,compertmantalised suitable for 415 Volts 3 phase 4 wire, 50 Hz AC supply system, dust and vermin proof, made of 3.15mm CRCA MS sheet with digital Volt meter, Ammeter, with CTs ,Led lamps RYB for all incomers & outgoings MCCBs are to busbar spadles to fitted complete base frame of 50x50x6mm angle iron , powder coated, having front and rear openeable hinged double door shutters with aprons for cable entry and locking arrangement complete with following :- Incoming:- (a) MCCB 315/320 amps, 4 pole, 50Hz ,415 V with rupturing capacity 35/36 KA-01 No. (b) Bus bar electrolytic grade Aluminium and supported on Non-hygroscopic, non carbonising, corrosion resistance SMC insulators 500 Amp,4 pole, not less than 75 cm long mounted on insulators 01 set.

Outgoing:- (a) MCCB 4 pole ,Ics=100%Icu- 25/26 KA, 415 Volts, 160 Amps , with thermal adjustable and fixed magnetic setting with extended terminals -02 Nos. (b) MCCB 4 pole ,Ics=100%Icu- 25/26 KA, 415 Volts, 100 Amps , with thermal adjustable and fixed magnetic setting with extended terminals -02 Nos. Note- (i) Rate quoted is deemed to be inclusive of PCC foundation/pedestal and connected earth work. (ii) Panels shall be placed above 0.6 mtr from ground level. (iii) Outgoing MCCBs shall be fed with solid busbar connectors. (iv) Cables shall be terminated using gun metal /SS glands. (v) including suitable thimbles/lugs, nut bolts ,washers fitted the cables. (v) cable glands for incoming and out going suitable cables is including rate quated by vendover.

S&F in replacement MCCB 4 pole, Ics=100%Icu- 25/26 KA, 415 Volts, 160 Amps , with thermal adjustable and fixed magnetic setting with extended terminals complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCCB 4 pole, Ics=100%Icu- 35/36 KA, 415 Volts, 250 Amps ,with thermal adjustable and fixed magnetic setting with extended terminals complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCCB 4 pole, Ics=100%Icu- 35/36 KA, 415 Volts, 200 Amps ,with thermal adjustable and fixed magnetic setting with extended terminals complete all as specified and directed by Engr-in-Charge.

S&F in replacement MCCB 4 pole, Ics=100%Icu- 25/26 KA, 415 Volts, 100 Amps, with thermal adjustable and fixed magnetic setting with extended terminals complete all as specified and directed by Engr-in-Charge.

S&F LED Street light 90 watt made uppressure diecast aluminium housing with toughned glass and high power leds and secondary lens with IP 66 protection system of efficasy >110 LPW including 10 KV SPD including taking down old UNSV Street lights complete all as specified and directed by Engr-in-Charge.

GI pipe bracket Suitable size of light single swan neck shape suitable to fix on top of tubular pole complete with clamps, nuts, bolts and washers complete all as specified and directed by Engr-in-Charge.

S&F of Steel tubular swaged poles erected to truly vertical or planted as strut complete with 6 mm thick mild steel base plate, welded to Pole, B-118 finial taper cap, bolts, nuts and screws, poles made out of ERW MS tubing conforming to IS-2713 Part-II type 410-SP-31 (9m long) including drilling of holes of required size for fixing of cross arms, painting the exposed surfaces of pole with two coats of aluminum paint over a coat of red oxide zinc chrome primer and with two coats of black bituminous paint on the and portion embedded in concrete, making five black and white bands at lower portion of pole above ground level/coping each 300 mm wide alternately and marking pole number. with black paint at suitable height complete all as specified and directed by Engr-in-Charge. Note:- The earthwork, PCC foundation, steel clamps, MS Cross arms & bracing of angle iron etc will be included deemed tobe rate coated for contractor.

S&F of Steel tubular swaged poles erected to truly vertical or planted as strut complete with 6 mm thick mild steel base plate, welded to Pole, B-118 finial taper cap, bolts, nuts and screws, poles made out of ERW MS tubing conforming to IS-2713 Part-II type 410-SP-31 (12 m long) including drilling of holes of required size for fixing of cross arms, painting the exposed surfaces of pole with two coats of aluminum paint over a coat of red oxide zinc chrome primer and with two coats of black bituminous paint on the and portion embedded in concrete, making five black and white bands at lower portion of pole above ground level/coping each 300 mm wide alternately and marking pole number. with black paint at suitable height including The earthwork, PCC foundation,deemed to be coated rate by contractor complete all as specified and directed by Engineer-in-Charge.

S&F thermoplastic, polystyrene unbreakable junction box size 260 x 210 x 116 mm suitable for pole mounted outdoor type IP 65 insulated complete with FI clamp & nut, bolts, washers and including phase seperator between R, Y, B terminals and one MCB SP 6 amp 10 KA, all duly mounted on din cannel, cable glands for cable entry complete all as specified and directed by Engr-in-Charge.

S&F in LED flood light with lens 150 watt made uppressure diecast aluminium housing with toughned glass and high power leds and secondary lens with IP 66 protection system of efficasy >110/125 LPW including 10 KV SPD including taking down old UNSV Street lights complete all as specified and directed by Engr-in-Charge.

M&L in replacement of PVC insulated multi stranded copper conductor PVC cable sheathed 2.5 sqmm 3 core and making connections of street light fittings and bollards lights complete all as specified and directed by Engr-in-Charge.

S&F of Steel tubular swaged Ring suitable for 12 m long pole for semi highmast light and for fixing of four nos flood loghts with bolts, nuts and screws, ring made out of ERW MS tubing conforming to IS-2713 including drilling of holes of required size for fixing of brackets , painting the exposed surfaces of ring with two coats of aluminum paint over a coat of red oxide zinc chrome primer and with two coats of silver paint on the surface complete all as specified and directed by Engr-in-Charge.

S&F in replacement of automatic street light control switch of 8 KW three phase using Infrared sensor based Nature Switch for automatic switching of street light. Nature switch operation should be based on Natural Light Lux*level. Reqd illuminance level also have part night operation facility for min 4 hrs to max 12 hrs. The sensor along with suitabe rating power contractor (s), one Incoming and three Outgoing MCBs rating of 20-32 Amps & main load circuit wiring (copper) of min 10 sqmm should be enclosed in a pole/wall mountable rust proof, electric shock proof, termite proof and FR grade thermoplastic polycarbonate enclosure conforming to IP66 protection class-2 (Hansel make). The circuit should be also have provision for manual operation (i.e. sensor by pass option) complete all as specified and directed by Engr-in-Charge.

Supply and Laying and fixing in replacement of along the poles or passing through pipes or laid under floor of through walls etc jointing and testing LT Cross Linked Polythene Insulated (XLPE insulated) galvanized steel strip armoured electric cable 1100 volt grade heavy duty size of 150 sqmm 3.5 core ISI marked with aluminium conductor and overall served with an outer sheath of PVC, of cross sectional area as under including taking out old UNSV LT cables complete all as specified and directed by Engr-in-Charge. Note : Excavation, earthwork, Pipe for cable protection to be measured and paid for separately.

All as per serial item No 19.00 here-in-before but of size 95 sqmm 3.5 core.

All as per serial item No 19.00 here-in-before but of size 70 Sqmm 3.5 core.

All as per serial item No 19.00 here-in-before but of size 50 Sqmm 3.5 core.

All as per serial item No 19.00 here-in-before but of size 35 Sqmm 3.5 core.

All as per serial item No 19.00 here-in-before but of size 25 Sqmm 3.5 core.

All as per serial item No 19.00 here-in-before but of size 16 Sqmm 4 core.

All as per serial item No 19.00 here-in-before but of size 16 Sqmm 2 core.

Supply & fixing or laying galvanised steel tubing light grade 80 mm dia (ISI marked) for protection of under ground cable on poles / walls under road crossing etc of following sizes including dismantling & taking down existing pipe complete all as specified and directed by Engr-in-Charge.

M&L forRoad cutting/ boring of existing road/path for laying of GI pipe protection for UG cable including making good distrurbed area/surface complete all as specified and directed by Engr-in-Charge.

M & L for providing earthing with GI earth plate electrode 600 X 600 X 6mm buried directly in ground (earth pit not less than 2.25M deep below ground level ) with top edge of the earth plate not less than 1.5M below ground level connected to GI strip 25 x 4 mm thick for earthing lead fixed by means of nuts,bolt,washers etc connected to earth test point complete all as specified in electrical plate NO 3 of SSR1996 part 1 ,including necessary excavation and earth work in any strata of soil,comman salt, charcoal dust, 40 mm dia light grade GI pipe for protection to earth lead, GI water pipe 20mm dia with funnel &wire mesh , PCC pit with CI cover and frame etccomplete all as specified and directed by Engr-in-Charge. Note:- All the joints shall be made with welding to get proper conductivity.Note: On testing after completion of earthing, if desired earth resistance is not obtained, the earthing will be re-done by the contractor at his own risk & cost to the entire satisfaction of Engr-in-charge

S&F double walled corrugated (DWC) pipe of size 77 mm including snap fit coupler conforming to IS14930 (Pt-II)/IS16205 Pt-II for protection of HT/LT cable in under ground complete all as specified and directed by Engr-in-Charge.

S&F double walled corrugated (DWC) pipe of size 63 mm including snap fit coupler conforming to IS14930 (Pt-II)/IS16205 Pt-II for protection of HT/LT cable in under ground complete all as specified and directed by Engr-in-Charge.

Excavation in trenches n. exc. 1.5 mtr in wide and n. exc. 1.5 mtr in depth for laying of underground cable and getting out in soft/loose soil complete all as specified and directed by Engr-in-Charge.

All as per Srl item No. 32.00 here-in-before but depth exceeding 1.5m but not exceeding 3m complete all as specified and directed by Engr-in-Charge.

Returning, filling in excavated soil in trenches including spreading, leveling, watering and well ramming in layers n. exc. 25 cm thick complete all as specified and directed by Engr-in-Charge.

Removing of excavted soil to a distance n. exc. 50 mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed by Engr-in-Charge.

Supply and fix servo controlled voltage stablizer of cap 75KVA confirming BIS 9815, Part:1994) 3 phase, 50HZ, Naturally, Oil cooled, Indoor, unblanced type, cooper wound, metallic body with lifting hooks, digital display type, relay free smooth and silent operation including filling of transformer oil up to level having following specification:- (a) Input voltage 300-480V. (b) Output voltage - 415 (+/-) 1%. (c) No distortion in Wave form. (d) Respond time not to exceed 20 mili sec. (e) Sensitivity (+/-)1%. (f) 8 volt/ second for single phase and 13 V/second for phase to phase. (g) Efficiency-95%. (h) Type of load 3 phase, unblanced type. (j) Digital display with volt and ammeter. (k) Overload and short circuit protection. (l) High and low voltage cut off. (k) By pass arrangement in case of emergency. Note:- Necessary PCC foundation required for installation & fixing is deemed to be included in rate quoted by the contractor.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 95.sqmm 3.5 core complete all as specified and directed by Engr-in-Charge.

Supply and installed Deep Freezer of 320 ltrs cap has deodorizer other features, Defrosting type, Frost Free, Compressor type, Standard with double door hard top type, Frost free comressor type, refrigerant R134a, deforst Manual, caster wheels available Tempreture range should be (- 180C to 200 C) Door gasket - Non Magnetic, inside cladding/ liner- Aluminium outer body PC.4 star energy rating complete all as specified and directed by Engr-in-Charge.

Supply and installed voltage stabilizer for automatic operation single phase naturally air cooled indoor type and disigned for input voltage 170V to 250V with output voltage 230V with accuracy of +- 2.5% and capacity 3 KVA complete all as specified and directed by Engr-in-Charge.

Supply and installed voltage stabilizer for automatic single phase naturally air cooled indoor type and disigned for input voltage 170V to 250V with output voltage 230V with accuracy of +-2.5 and capacity 5 KVA complete all as specified and directed by Engr-in-Charge.

Supply and installed AC in wall split unit air conditioner reversible type indoor and outdoor unit complete with cordless remote control unit and with built air plasma filter for better inddor air quality of capacity 1.5 ton with standard accessories including MS frame work for installation of outer with side and making reqd hole in wall for passing of cooling pipes/cable and repair work tone demaged portion of wall in CM 1:4 complete all as specified and directed by Engr-in-Charge.

Supply and installed of Desert Cooler electric driven single phase (or nearest size) plastic/PVC body of capacity 5000 cum per hours (or nearest size) complete all as specified and directed by Engr-in-Charge.

FANGALIA TRADERS

ARNABH ASSOCIATES

ATUL TRADING CO

CITY TOP ELECTRICAL WORKS

HIMALAYA ENTERPRISES

slathia construction works

PROACH ASSOCIATES BUILDERS & ENGINEERS

MOHAN LAL AND SONS