GE/C-71/2022-23 PETTY REPAIRS FOR DAILY WORK INCLUDING MISC E/M WORKS AND DAILY MAINTS COMPLAINTS IN THE AREA OF RR COLONY RRRC TRG AREA AND ARJAN VIHAR UNDER GE CENTRAL DELHI CANTT -10

Amount

Checking the leakage and petty repairs/replacement to Wall Mixer, WHB Mixer, Sink Mixer, bib taps, Pillar taps, Stop cock, Conceled stop cock, angle valves, gate valves etc of any description or size for stopping leakage of water by changing washers, etc complete all as specified and directed by Engineer-in-Charge. Note:- for Ser No 1 to 8: 1. Note : Fixtures/Fittings required to complete the job shall be paid under relevant item against supply only and rates quoted by the contractor are deemed to inclusive of necessary tools and plants incl mtrls of Dhaga/ safeda/M seal/Taflon tape/solvent/ screws/white cement/Nails,Screws/Gitties etc. 2. The complaints to be rectified within four hours on same day. The Delay in rectification of complaint more than four hours, the penality will be levied @ Rs.100.00 Per complaint. 3. Serally numbered docket booklet shall be provided by contractor without any extra cost. 4. In case of any urgent nature plumbing complete after 1700 hrs same shall also be attended to and nothing extra shall be admisible on this account.

Repairs to low level flushing cistern syphon, washers, handles, float valves, stopping leakage of Down pipe by applying m-seal and other related works of to make the flushing cistern functional complete all as specified and directed by Engineer-in-Charge.

Removal of air lock, blockage of water pipes from OHT tanks to supply point and repairs/adjustment to float valves, applying of M-seal in tanks and all other connected works of water supply from Over head water storage tanks / PVC tanks complete all as specified and directed by Engineer-in-Charge.

Repairs to 50mm/75mm/100mm PVC or CI Pipes, Branch pieces, Tee Junction, Sockets, Door plates, floor traps, Nahani traps, EWC lip ring half S set incl all fittings to make the pipe functional complete all as specified and directed by Engineer-in-Charge.

Petty repairs to joinerys works, such as easing/adjusting of door, repairs of wire mesh, cub board shutters, iron mongerys, false ceiling works of any type or description and any type of carpentery works etc Easing of window shutters/CB shutters (One unit shall comprise of one window/CB/Showcase irrespective of number of leaves) for properly closing/opening , tightening of hinges or changing the position of hinges, adjustement of tower bolts sliding bolt etc complete all as specified and directed by Engineer-in-Charge.

Petty repairs to joinerys works, such as replacement refixing of glass panes, wiremesh, glass putty, aluminium beading, door closure, any type of handles, Tower bolts, hinges, sliding bolts, rubber beading, door seal, piano hinges,floor door stopper, etc complete all as specified.

M&L petty repairs to plaster, floor, plinth etc and like by PCC 1:2:4 Type B0 and plaster in CM 1:4 incl preparing roungening and cleaning the surface, and neat cement slurry as required making good, finishing even and smooth without using extra cement in patches area n exc 0.50 Sqm each patch and removal of rubbish off the premises complete all as specified and as directed.

M&L petty repairs to wall tiles, floor tiles, skirting, dado, kota stone , granite stone, RCC Jali, window cill, door jambs, ceiling plaster, fixing of EWC and IWC and neat cement slurry as required making good, finishing even and smooth without using extra cement in patches area n exc 1.00 Sqm each patch plaster, floor, plinth etc and like by PCC 1:2:4 Type B0 and plaster in CM 1:4 incl preparing roungening and cleaning the surface, and removal of rubbish off the premises complete all as specified and as directed.

Supply only Sheet glass, 3mm thick ordinary quality, in squares n exc 0.50 sq. m each pane glazing with oil putty or glazing clips or wooden beadings, aluminium beadings etc complerte all as specified and directed by Engineer-in-Charge.

Supply only Stainless steel wire cloth 0.50mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire stapple etc on 2nd class HW wooden/ fillets (15mmx15mm) duly painted with synthetic enamel paint complerte all as specified and directed by Engineer-in-Charge.

Supply only two legged aluminium floor door stopper with rubber shoe 140mm long complerte all as specified and directed by Engineer-in-Charge.

Supply only 250mm long aluminum alloy anodised sliding door boll with hasp staple balt-type and fixing clips of sheet case or extruded sections and fixing bolls and sliding bolls extruded sections or case aluminum alloy complerte all as specified and directed by Engineer-in-Charge.

Supply only 150mm long extruded alumiunium alloy handle fabricated type anodized (D type) complerte all as specified and directed by Engineer-in-Charge.

Supply only 150 mm size aluminium, anodised barrel tower bolts of extruded section and fixed to shutter complerte all as specified and directed by Engineer-in-Charge.

Supply only Stainless steel drapery rod 20 mm of dia ,with bracket including premium balls complerte all as specified and directed by Engineer-in-Charge.

M & L for Welding in repairs n. exc 2.5cm in length Thickness of Metal to be welded is not exc 6mm thick complerte all as specified and directed by Engineer-in-Charge.

Supply only vitreous china wash down water closet pan (padestal pattern) white incl 'P' or 'S' 100 mm trap and making good the disturbed surface to match with the existing complete all as specified and all as directed.

Supply only vitreous china squatting pan Orissa pattern long pan size 580x440mm white with integral foot rests ‘standard Grade P’ or ‘S’ trap front or back inlet complete all as specified and directed by Engr-in-Charge,

Supply only 10 ltrs PVC (White) valve less syphonic action type, flushing cistern low level with inlet ball valve float, handle, Aluminium brackets for bottom support fixing with gitties embeded in wall with drilling machine etc complerte all as specified and directed by Engineer-in-Charge.

Supply only PVC flush pipe of 32mm dia pipe with two Nos check nuts for connecting low level flushing cistern to EWC/IWC complerte all as specified and directed by Engineer-in-Charge.

Supply only vitreous china wash hand basin (flat back) white of size 550X400mm excluding taps, waste chain and plug and porcelain stopper including a pair of mild steel angle iron brackets of suitable size and waste pipe & waste fittings complete all as specified.

Supply only Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; complerte all as specified and directed by Engineer-in-Charge.

Supply only plastic water closet seat cover white closed pattern with flat bottom and cover incl mild steel chromium plated hinging device complerte all as specified and directed by Engineer-in-Charge.

Supply only stainless steel toilet paper holder with gutties and steel screws on walls complerte all as specified and directed by Engineer-in-Charge.

Supply only stop valve cast copper alloy screwed down high pressure with cruch or butterfly handle screwed both ends for iron pipe or for union and fixed for 15 mm bore complerte all as specified and directed by Engineer-in-Charge.

Supply only angle valve 15mm dia fancy type chromium plated all as specified and directed by the Engr-in-charge.

Supply only suitable for 15mm dia brass chromium plated pillar tap with fly nuts capastan head screwed down high pressure with or without lettered hot or cold with long scewed shank complerte all as specified and directed by Engineer-in-Charge.

Supply only 15 mm dia Brass CP 3-in-1 wall mixer for mixing hot & cold with L bend water screwed down for iron pipe and fixed complerte all as specified and directed by Engineer-in-Charge.

Supply only 15 mm dia Brass CP mixer long Neck for sink mixing hot & Cold water screwed down for iron pipe and fixed complerte all as specified and directed by Engineer-in-Charge.

Supply only bib taps 15 mm bore chromium plated brass, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

Supply only stainless steel soap dish complerte all as specified and directed by Engineer-in-Charge.

Supply only CP brass shower rose 125mm size suitable for 15mm bore pipe with C P arms complerte all as specified and directed by Engineer-in-Charge.

Supply only brass spindle/phase suitable for 15mm dia bib cock, stop cock, conceled stop cock, angle cock, wall mixture, basin mixture etc of any type or size complerte all as specified and directed by Engineer-in-Charge.

Supply only Health faucet, CP brass with 1.50m long flexible pipe complerte all as specified and directed by Engineer-in-Charge.

Supply only 32mm bore and 75cm long PVC waste pipe for WHB complerte all as specified and directed by Engineer-in-Charge.

Supply only PVC connection pipe of 15mm X 600mm " size with 2 Nos brass check nuts with washers,complerte all as specified and directed by Engineer-in-Charge.

Supply only fancy type looking mirror of size 600x450x6mm with 100 mm wide fancy type border fixed with 4 Nos stainless steel clips complerte all as specified and directed by Engineer-in-Charge.

Supply only Glass Corner Shelf 6mm thick including CP railing radius 250mm complerte all as specified and directed by Engineer-in-Charge.

Supply only Glass shelf assembly5.5mm thick, 600mm long 120mm wide with cp railing complerte all as specified and directed by Engineer-in-Charge.

Supply only of 15mm bore size PTMT bib tap complerte all as specified and directed by Engineer-in-Charge.

Supply only stainless steel plate rack of size 90x80x25 cm depth size made out of 0.80mm thick sheet complerte all as specified and directed by Engineer-in-Charge.

Supply only steel sink with drainage board made out of 0.80mm thick sheet for kitchen with plug, washers, waste pipe incl fixing cast iron cantilever bracket connecting union over all size 915x460mm with bowl size410x330x160mm complerte all as specified and directed by Engineer-in-Charge.

Supply only chromium plated grating (round) 125mm dia fixed over floor/nahani trap (with hole and without hole) complerte all as specified and directed by Engineer-in-Charge.

S&F Rotational moulded polythylene 1000 Ltr capacity water storage tank tripple layered WHITE (Cylindrical vertical with closed top )composite type or lid should be thread type) hoisted and fixed in position with 20mm dia brass float valve including taking out existing unserviceable overhead tank of any description complerte all as specified and directed by Engineer-in-Charge.

S&F Rotational moulded polythylene 500 Ltr capacity water storage tank tripple layered WHITE (Cylindrical vertical with closed top )composite type or lid should be thread type) hoisted and fixed in position with 20mm dia brass float valve complete including taking out existing unserviceable overhead tank of any description complerte all as specified and directed by Engineer-in-Charge.

Supply only 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complerte all as specified and directed by Engineer-in-Charge.

Taking up or down steel tubing and connections, including cleaning for re-fixing, bore of tubing 15mm

Taking up or down steel tubing and connections, including cleaning for re-fixing, bore of tubing 20mm

Supply and fix galvanized steel tubing, 15 mm bore medium grade including all fittings and short tube pieces, fixed complete to walls and ceilings or laid in floors complete all as directed.

Supply and fix galvanized steel tubing, 20 mm bore medium grade including all fittings and short tube pieces, fixed complete to walls and ceilings or laid in floors complete all as directed.

M & L for Cutting existing steel tubing 15mm bore for alterations or additions (Each cut measured) complerte all as specified and directed by Engineer-in-Charge.

Cleaning and removing all scale and dirt, etc, from tanks of 500& 1000 litres capacity and from mouths of circulating pipes, etc and applying bleaching powder for cleaning on tanks complerte all as specified and directed by Engineer-in-Charge.

Demolition and breaking up rain water pipes (CI,AC,PVC etc) set in any cement mortor of any diameter incl bends.

Supply only 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, waste and vent pipes in any length with or without ears, fixed in walls/floors/ trenches etc complerte all as specified and directed by Engineer-in-Charge.

Supply only 100mm dia sand cast Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed in walls/floors/trenches etc complerte all as specified and directed by Engineer-in-Charge.

Supply only 75mm dia sand cast Cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed in walls/floors/trenches etc complerte all as specified and directed by Engineer-in-Charge.

Demolition of stone slab and tiles of any description or thickness in floor apron etc complete all as specified and directed.

M&L for glazed coloured ceramic tiles (300x600mm) x6 to 7mm thick in dado etc set and jointed in neat cement slurry and pointed in coloured cement to match incl 10mm thick backing coat in cm 1: 4 complerte all as specified and directed by Engineer-in-Charge.

M&L for non skid coloured ceramic tiles (300x300mm) x6 to 7mm thick in floor etc set and jointed n neat cement slurry and pointed in coloured cement to match incl 15mm thick secreeding in CM 1 : 6 complerte all as specified and directed by Engineer-in-Charge.

M&L for machine pressed precast cement concrete inter locking paver block any shap and size ,60 mm thick M-35 grade , confirming to IS 15658-2006, over 75mm tkick PCC type D-2 1:4:8 (40 mm graded aggregate) all as specified.

S&F Cequered cement concrete tiles with grey cement and pigment 30cm X30cm X22mm thick set jointed and pointed in neat cement slurry in floors and including 75mm thick cement concrete type D-2 1:4:8 and incl 15mm thick screed bed in CM 1:6 all as specified and directed.

M&L for sand filling under floor or in foundations including watering and consolidation.

S&F Non - skid Ceramic colour tiles 600 x600 x 7 to 8 mm thick in floors etc and 15mm thick screed bed 1:6 in cement mortar. set and jointed in neat cement slurry and pointed in white or coloured cement to match all as specified.

Taking down cement plaster from brick or concrete surface incl racking out joints hacking for key and scrubbing down with water complete including removal of rubbish off the premises complerte all as specified and directed by Engineer-in-Charge.

M&L for rendering 15mm thick in CM 1:4 on fair faces or other than fair faces of brick work or concrete surfaces firnished even and smooth without using extra cement up to hieght of four storey bldg ,including scaffolding complete.

Demolition of brick work built in cement mortar of any position or description complerte all as specified and directed by Engineer-in-Charge.

M & L for brick work with Cement Mortar1:6 using sub class 'B' bricks,old size , straight or curved on plan exceeding 6 m mean radius all as specified and directed.

Demolition of reinforced cement concrete as in roof slabs, chajjas, fins, facia, parapet, drops, railings, beam, lentils, cover slabs, and similar other works as directed including cutting of steel reinforcement to facilitate dismantling complerte all as specified and directed by Engineer-in-Charge..

Material and labour for precast RCC 1:2:4 type B-0 45mm thick (measured solid) as in louvers, jallies including set in CM 1:6 complete including demolition of existing jallies all as specified. and directed at varying height from G.F. to G+5 Floor complerte all as specified and directed by Engineer-in-Charge.

Supply only 15 mm bore GI fittings such as union, Socket, Tee, Elbow, Nipple 4" 6", Reducer, Plug, and tank nipple complete all as specified and directed.

Supply only 20 mm bore GI fittings such as union, Socket, Tee, Elbow, Nipple 4" 6", Reducer, Plug, and tank nipple complete all as specified and directed.

Supply only PTMT waste coupling 32mm dia for sink.

Dismentling asbestos cement corrugated or semi corrugated sheets in roof fixed with L hook or cranked bolt.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Dismantling wrought iron or mild steel work of any description such as guard bars, grills etc.

S&F Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks, roof truss and similar work incl welding and drilling con- forming to Fe.290.Gde-E-165

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding/ridges/gutter to wall, fixed with self tapping screws all as specified.

Dismantling of wall and ceiling board fibre pulp AC boards etc any thickness including cover fillets removing the wiring and refixing the same including fixture as necessary at site including frame work.

M & L for snap grid ceiling with E - board ceiling tiles of size 600x600mm 4mm thick incl aluminium alloy anodised at edges angle 25x25x1.5mm and tee section 38x38x1.5 mm at other than edges both ways fixed with 4mm dia gi wire including two coats of oil bound distemper.

Checking electrical points for continuous electric supply system and replacement of unserviceable spares for all electrical fixtures, ceiling/exhaust fans of any size and capacity and carrying out minor repairs, fixing screws, tightening of loose wires, any type renewal of small pieces of electric wire upto 1.00 mtr length and maintenance work complete on all working days including holidays all as directed by Engr-in-charge at Arjan Vihar and adjoining area.

Attending to complaint of unsv switch ,socket ,fan regulator and making of light / power point in casing caping upto 2 mtr of length and maintenance work complete on all working days including holidays all as directed by Engr-in-charge at Arjan Vihar and adjoining area.

Attending to Geyser complaints at site including checking and rectification of any electric fault/ water leakage and making good in all respects including minor repairs, replacement of unserviceable spares, burnt copper wire connections wherever required and repairing any type of switch, socket, plug top etc complete all as specified and directed. Notes for Item No. 80, 81 & 82 (a) fixtures / fittings shall be paid under relevant item against supply only. (b) Contractors are advised to visit the sites before quoting their rates. (c) Materials for minor and maintenance repair works as directed by Engineer-in-Charge shall be supplied by the contractor within one week from the date of issue of work order. (e) Contractor shall provide and deploy adequate experienced professional to carry out day to day complaints and must deploy 01 electrician and 01 helper at Pratap Chowk Complaint cell from 0900Hrs to 1700 Hrs from Monday to Sunday. Electrician and helper shall report to complaint cell at 0900 hrs daily and get the job card for carry out the work and same will be retrun to concered JE at 1700 hrs as token of completion of job. In case of any breakdown/ emergency, contractor shall make arrangement to attend and rectify the complaints in odd hours on sunday/ holiday also. The rates quoted in sch 'A' respective items shall be deemed to be included and nothing extra shall be admissible on this account. Note: whatever be the nature of electrcal complaint the wholesole rectification responsibilty lies with the contractor. (f) Contractor shall be penalised @ Rs. 100/- per complaint per day, if he fails to attend the complaint within 4 hours. (g) All ser numbered complaint docket will be provided by contractor and amount of docket included in this. (h) Daily attendance register will be maintained by conserned JE and if any electrician/ helper found absent on any working day then penalty @Rs 1000/- per day per workman will be recoverd from the contractor.

Attending to electrical complaint of no light / short circuit in light or power circuit / MCCB tripping or any other emergency nature complaint during night hours (from 09 pm to 05 am). Notes for Item No. 83 (a) fixtures / fittings shall be paid under relevant item against supply only. (b) Contractors are advised to visit the sites before quoting their rates. (c) Materials for minor and maintenance repair works as directed by Engineer-in-Charge shall be supplied by the contractor within one week from the date of issue of work order. (e) Contractor shall provide and deploy adequate experienced professional to carry out day to day complaints and must deploy 01 electrician at Pratap Chowk Complaint cell from 2100 Hrs to 0500 Hrs from Monday to Sunday . Electrician shall report to complaint cell at 2100 hrs daily . In case of any breakdown/ emergency, contractor shall make arrangement to attend and rectify the complaints in odd hours on sunday/ holiday also. The rates quoted in sch 'A' respective items shall be deemed to be included and nothing extra shall be admissible on this account. Note: whatever be the nature of electrcal complaint the wholesole rectification responsibilty lies with the contractor. (f) Contractor shall be penalised @ Rs. 100/- per complaint per day, if he fails to attend the complaint within 4 hours. (g) Daily attendance register will be maintained by converned JE and if any electrician/ helper found absent on any working day then penalty @Rs 1000/- per day per workman will be recoverd from the contractor.

Supply only switch piano flush button type single pole one way 6 Amps all as specified.

Supply only switch piano 6 amp SP two way, ISI marked

Supply only socket piano outlet 6 Amp flush button type all as specified & directed.

Supply only bell push single pole 6 Amps all as specified.

Supply only switch piano flush button type single pole 16 Amps.

Supply only socket piano outlet, 2 in 1, 3 pin 6 and 16 Amp single pole .

Supply only Ceiling fan regulator electronic step switch type/socket type, suitable for 1200/1400 mm sweep ceiling fan, 230 Volts single phase complete.

Supply only switch Modular type 6 Amps one way 230V AC complete all as specified and directed by Engineer in charge.

Supply only switch Modular type 6 Amps two way 230V AC complete all as specified and directed by Engineer in charge.

Supply only replacement Modular Bell push button SP with indicator 6 Amps, 1 module 230V AC complete all as specified and directed by Engineer in charge

Supply only Modular socket outlet 5 pin 6 Amp socket 2 moduler complete all as specified and directed by Engineer in charge.

Supply only switch Modular type 16 Amps one way 230V AC complete all as specified and directed by Engineer in charge.

Supply only Modular socket outlet 5 pin 6/16 Amp universal socket 2 module complete all as specified and directed by Engineer in charge.

Supply only Modular five stepped type electronic fan regulator 1/2 module 230V AC complete all as specified and directed by Engineer in charge.

Supply only ceiling rose surface PVC type with three terminals.

Supply only Electric bell Ding-Dong AC 230 Volt etc complete all as specified and directed.

Supply only insulated body, angle holder (metal ring) with back plate ISI marked complete all as directed.

Supply only industrial metal clad plug top, 3 pin, 10amp / 20 amp (ISI marked) as directed.

Supply only industrial metal clad socket 3 pin 10 amp / 20 amp (ISI marked) as directed.

Supply only plug top 16 Amps 3 pin 230- volts.

Supply only LED batten luminaire surface mounted, 4 feet system wattage of 22 Watts, > 2400 systems lumen outputwith lifetime of 50000 burning hours with 70% of its initial lumen maintained. CRI>80, Power Factor > 0.95, THD< 10%, colour temperature - 6500K, surge protection 2.5KV in CM, IP-20 protected, meets LED IS specifications, Class - 1, Short circuit and over circuit protection, voltage range - 150 to 270 Volts AC, temperature range 0 to 50 DegreeC and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed.

Supply only LED batten luminaire surface mounted 2 feet system wattage of 10 watts and not less than 1000 lm with life time of 50000 burning hours with 70% of its initial lumen maintained. CRI > 80, power factor > 0.95, THD < 10%, color temperature > 6500 K , surge protection 2.5 KV in CM IP- 20 protected meets LED IS specifications, voltage range - 150 to 270 volts AC, temperature range 0 to 50 Degree C, system efficiancy at luminarie level ≥100 Lumens/watt and including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire fixed complete all as specified and directed.

Supply only LED 9/10 watts bulkhead fitting with powder coated die cast aluminium housing with glass/ non yellowing polycarbonate cover, IP65 Protection, System level efficacy of the Luminary is > 90 lm/W with a life class of 50,000 burning hours at L70 criteria, Power Factor >0.95, driver with Voltage range 150-270V, Temperature range 0 to 50 Deg, Driver efficiency >85%, THD<10%, CRI>80, Color Temperature-6000K, Surge protection of 2.5 KV, including connecting up with necessary PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete all as specified and directed.

Supply only surface ceiling mounted, round LED down light fitting 12 watts with die cast aluminium housing and system wattage of 12W, system efficacy at luminary level ≥ 80 Lumens/watt, 50000 burning hours, 6500K color temperature with CRI >80, Power Factor > 0.90, Driver should meet IEC compliant for safety with multi stage high Isolate CC-CV operated driver with voltage variation range - 150 to 270 Volts AC, and surge protection of 2.5 KV, and including connecting up with PVC sheathed 3 core 1.5Sqmm copper conductor flexible wire fixed complete all as specified and directed.

Supply only in replacement of decorative type wall mounted luminaire (Comet) with unbreakable poly carbonate materials suitable for 1x14 watt LED bulb B22 base.

Supply only 14W LED Bulbs, high energy efficiency LED luminaries to be fitted on existing holders 240 V,50 Hz

Supply only 9 W LED Bulbs, high energy efficiency LED luminaries to be fitted on existing holders 240 V,50 Hz

Supply only MCB SPN 40 Amps 240 volts 10 KA 50 HZ 'C' curve complete.

Supply only MCB DP 20 Amps 240 volts 10 KA 50 HZ 'C' curve complete.

Supply only MCB SP 6-32 Amps 240 volts 10 KA 50 HZ 'C' curve complete.

Supply only MCB DP 63 Amps 240 volts 10 KA 50 HZ 'C' curve complete.

Supply only MCCB 160 Amps, FP 415 volts 16 KA 50 HZ with thermal magnetic setting.

Supply only MCCB 250 Amps, FP 415 volts 25 KA 50 HZ with thermal magnetic setting.

Supply only single pole and neutral enclosure with a two pin earth plug and socket complete with one single pole MCB SP 20 Amp complete all as specified and directed.

Supply only PVC Gang box surface type heavy duty suitable for single switch 5 Amps (ISI Marked) .

Supply only Gang box surface type heavy duty suitasble for 15 Amps switch and socket (ISI Marked)

Supply only replacement white cover plate with frame 1 module/ 2 module complete all as specified and directed by Engineer in charge.

Supply only replacement white cover plate with frame 3 module complete all as specified and directed by Engineer in charge.

Supply only replacement white cover plate with frame 6 module complete all as specified and directed by Engineer in charge.

Supply only replacement white cover plate with frame 8 module complete all as specified and directed by Engineer in charge.

Supply only replacement of capacitor 3.15 Mfd, 240 V complete all as specified and directed.

Supply only replacement of capacitor 2.5 Mfd, 240 V complete all as specified and directed.

supply only hole fastner madeup of MS 6" long with complete nut bolt all as specified.

supply only hole fastner madeup of MS 4" long with complete nut bolt all as specified.

Supply only heating element of 2 KW any type with nut bolt washer complete all as directed.

Supply only heating element of 1.5 KW any type with nut bolt washer complete all as directed.

Supply only non return valve 15mm dia (ISI Marked) for geysers of 50/35/25 Ltr capacity including GI Socket,Nipple, elbow ,bend etc and connecting up complete all as directed.

Supply only for safety pressure valve of size 15 mm dia, ISI marked for geysers complete all as directed by Engineer-in-charge.

Supply only thermostat for 25/35/50 ltrs capacity of geysers complete all as directed.

Supply only SS braided pipe of 12 mm ((internal) suitable for hot/cold water, 60 cm long with brass nuts and rubber washers complete all as specified and directed.

Supply only FRLS insulated single core unsheathed multistranded copper conductor 1100 volt 1.5 sqmm with approved colour code completed all as specified.

Supply only FRLS insulated single core unsheathed multistranded copper conductor 1100 volt 2.5 sqmm with approved coloured code completed all as specified.

Supply only FRLS insulated single core unsheathed multistranded copper conductor 1100 volt 10 sqmm with approved coloured code completed all as specified.

Supply only replacement copper cable flexible 3 core PVC insulated of size 23/.0076 ll as specified and directed by Engr-in-Charge

Schedule of Credit

LAMBA ENTERPRISES

SHREE RAM BUILD TECH

M/S ANIL KUMAR

imran construction company

POONAM ENTERPRISES

M/S MSD & Associate