COMPREHENSIVE PETTY REPAIRS TO INCL PLASTERING FLOORING TILES BRICK WORK ROOF AND OTHER CONNECTED WORK AND JOINARY WORKS IN UNDER AGE BR I AT MIL STN BIKANER

Amount

Demolition of brick work built in cement mortar

Demolition of cement conc. In ground floor and paving not exc. 15cm thickness (below or above GL) incl any type of floor finishes/topping

Demolition of reinforced cement conc.as in chhajas, parapets etc. not exc. 15cm thickness .

Dismanting floor, hearth or wall tiling including cement mortar bedding and removal of rubbish out of the premises

Demolition of lime conc. of any desc.and in any position not other wise specially provided for.

Dismantling Asbestos cement Corrugated sheets in roof covering .

Dismantling plain or corrugated steel / transulecent sheeting any gaugr pattern thickness incl nanital or similar pattern

Dismantling one way Jaffri including taking as under of battens in trellis all as directded and as specified by Engineer in charge

Taking down cement plaster (any thickness and incl tiles if any) on brick or stone walls incl.raking out joints hacking for key scrubbing down with water etc.

Taking down chowkhats or frames not exc. 1.50sqm each but with shutter (w/o taking of shutter from the frame ) including Windows /ventilators complete

Taking down chowkhats or frames exc. 1.50sqm and not exc 4 Sqm each but with shutter (w/o taking of shutter from the frame )

Taking down door shutter of any desc exc 1 sqm but not exc 2 sqm and refixing in the same opening.

Taking down door shutter of any desc exc 1 sqm but not exc 2 sqm and romoving to store

Taking down door shutter of any desc exc 2 sqm and romoving to store

Taking down shutters of any description (Aluminum ) and refixing in same opening after carrying out necessary repairs , securing rails ,tightening scews ,hinges etc

Taking down Aluminium door including chowkhat if required and repair the same including repair of rubber bedding , aluminium clip, adjustment of glass repair of floor spring or hydraulic door closer with oiling or greesing etc including adjusment of horizontal or middle style.complete all till the staisfaction of engineer-in-charge

Taking down aluminum windows including frame if required and repair the same including repair of rubber bidding,aluminum clip,adjusment of glasses,repair of floor spring or hydraulic door closer with oiling or greesing etc.ajusment of horizontal, vertical or middle style . complete all as till the satisfaction of Engr-in-charge.

Dismantling of existing false ceiling of ac sheet etc

Hacking out old broken glass (any thickness size quality or desc.)from wooden frames or stone conc. Or brick surroundsglazed with putty or fixed with beads exc.105sqm

Taking up or down steel water tubing 15mm dia and connection ,incl cleaning for refixing

Taking up or down steel water tubing 20mm dia and connection ,incl cleaning for refixing

Dimantling pipes of any desc.fixed to wall or laid under floor complete.

Dismantling Rotational Moulded polyethyelene water strogr tank of capacity exc 250 lit but not exc 500 lit complete all as specified and as directed by Engineer-in-Charge.

Dismantling Rotational Moulded polyethyelene water strogr tank of capacity exc 500 lit but not exc 1000 lit complete all as specified and as directed by Engineer-in-Charge.

Dismantling timer scantling over 40 sqcm in section in any position.

Do under 40 sqcm in section.

M&L for RCC 1:2:4 using 20 m graded stone aggregates on precast pillars moulded avg cross sectional area 100 x 100mm x 75cm long

M&L Precasrt cement concrete RCC jalli 35mm thick type B0 1:2:4 using 12.5mm graded aggregate (measured solid) including all mouldings but exc frame

M&L Brick work with sub class 'B' bricks (old sized bricks) straight or curved on plan exc 6m mean radius built in cement mortar 1:6

M&L Brick work with sub class B bricks (old sized bricks) straight or curved on plan to any radius in half brick walls built in CM 1:4 parapet

M&L brick work with fly ash bricks (old sized bricks) straight or curved on plan to any radius built in CM 1:4 all as specified.

M&L for cutting to existing flooring (Kota/Mosiac/stone flooring ) with and including polishing repaing .

M&L Rendering 15mm thick on fair faces of brick or conc. Surfaces in cement mortar 1:6,even and smooth w/o using extra cement

M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:4. (Note: Plaster shall be carried out in patches and contractor shall have no claim for any height and scaffolding what so ever is the location)

M&L Rendering 10mm thick on fair faces of conc. Surfaces in cement mortar 1:3,even and smooth w/o using extra cement as on ceiling.

M&L 15 mm thick rough cast plaster in Cement mortar 1:4 consists of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with course sand and cement in the ratio of 1:1:1 complete all as specified and as directed by Engineer-in-Charge.Note: The rate quoted shall be deemed to include for necessary use and waste of form work if required and nothing extra shall be paid on this account).

Supply only liquid water proofing compound, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

M&L PCC 1:4:8 as in sub base/mass concrete type D-2 using 40mm graded stone agg .

M&L for 40mm thick PCC type B-1 using 20mm graded aggregate as in pcc flooring finished with out using extra cement .

Supply only 3mm thick glass 38mm wide glass dividing stripps laid in design as directed by Eng-in-charge

M&L for 15 mm thick rendering 1:4 as in skirting finished even and smooth with using extra cement

M&L coloured Non skid ceramic tiles exc 0.11 Sqm and nexc 0.18 Sqm , 7mm thick in floors set and jointed in neat cement slurry and pointed in coloured cement to match the floor laid over 15mm thick screed in cement mortar 1:6.

All as per item No.42 above but on vertical surface over 10 mm thick rendering in CM (1:4).

M&L for 10 mm thick Vitrified colored tiles of size n.exc. 0.36 Sqm as in floors over 15 mm hick screed in CM 1:6 jointed in neat cement slurrry and pointed in white cement sluurry to match the shade of existing surfaces.(Note:The contractor shall have no claim on difference what so ever on shade /colour of tile).(Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

ditto as per Serial item No.44 above but with 10 mm thick in CM 1:4 as on vertcal surface.

M&L Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors on 15mm thick screeding in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete. (Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

M&L Glazed ceremic tiles white 450X300mmX7mm thick coloured,set and jointed in neat cement slurry and pointed in white cement or coloured to match colour matching with floor tiles as on vertical surfaces laid over 10mm thick cement screed in 1:4.(Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

M&L Machine cut kota stone slab 18 - 20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab incl.rubbing and polishing laid over 20 mm thick cement screed base in CM 1:6. The joints shall be 20mm wide filled with cast in situ tarrazo with white marble chips of size up to 6mm.(Note:- Rates for the work as in repair of chowkhats , GI Tubings or in patches area (n.exc. 5 Sqm) deemed to be included in the item contractor shall not claim extra payment for the same)

All as per item No 48 above but in skirtings laid over 10mm thick backing layer in CM 1:4

M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

M&L Sand stone slab 40-50mm thick set jointed and pointed self faced punched dressed laid as in plinth protection laid over 15mm thick screed in CM 1:6.

M&L Sand stone slab 40-50mm thick set jointed and pointed self faced punched dressed laid as in chhajas, sunshade and man holes covers set in cement mortar incl.making chases in wall.

M&L Granite 19 mm thick of any type work table rubbed and polised in steps,jambs,pillars,window cill, cooking plateforms and like in cement mortar 1:4 including pointing cement mortar 1:2 using marble dust with admixure of pigments to match with shade of granite

M&L Rendering 15mm thick on fair faces of brick /stone patti or conc. Surfaces in cement mortar 1:4 even and smooth w/o using extra cement as on roof slab mixed with liquid water proofing compound of Dr FIXIT/Sikka

M&L Preparing surface and cleaning of concrete slab by wire brushing and aplying evenly a tack coat of industrial bitumen 85/25 @ 1.70 Kg per sqm including cleaning surfaces complete all as specified and as directed by Engr-in-chanrge

M&L 50 micron polythylene sheet supplied and fixed complete all as specified and as directed by Engr-incharge

M&L Lime concret as terracing as specified in roof.

Extra over lime conc. Terracing for top surface trowelled smooth incl cement mixture to make homogeneous paste.

M&L 40 mm thick Brick tiles bedded in 15 mm thick cement and sand mortar (1:6) and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed by Engineer-in-Charge.

M&L For PCC type B1(1:2:4) using 20 mm graded cushed stone agg as in bands/coping ,benching and the like incl form work

M&L for reinforced cement concrete type B-1 (using 20mm graded crushed stone graded aggregatework as in slabs supported on walls , beams etc

M&L for form work to soffits of suspended slabs and similar work not exceeding 200mm thick

M&L for mild steel steel TMT bars 10mm dia and over cut to length bent to shape reqd ,incl cranking ,bending spirally for hooping columns hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia

M&L for mild steel steel TMT bars 6mm to 8mm dia and over cut to length bent to shape reqd ,incl cranking ,bending spirally for hooping columns hooking ends and binding with mild steel wire annealed not less than 0.9 mm dia

M&L 6mm thick asbestos cement corrugated sheets in roofs, walls fixed with L-type or cranked hook bolts.

M&L Asbestos cement two piece adjustable ridge 6mm thick fixed with Lor J hooks / coach screws

M&L for rolled section /tubular section as in main and cross beams , purlins , rafters ,posts where connected to common rafter and running rails etc conforming to Fe- 410-w

S&F 2mm thick glass reinforced translucent corrugated sheeting with two corrugation side lap fixe with coach screw and washer in roof, wall etc..

M&L Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified. (Note - Sand Color /or as approved By Garrision Engineer)

M&L Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified.(Note - Sand colour /or as approved By Garrision Engineer)

S&F 0.63mm thick galvanised mild steel sheets with two corrugation side lap fixed with J or L hooks with grade of zinc coating 275

S&F in repairs anodised aluminium snap grid frame work of size 605xx x 605mm for false ceiling including necessary notching. The snap grid shall consist of anodised aluminium main/cross tee of size 36.5 x 25 x 1.4mm weighing 0.24Kg/RM and 23.5 x 26.4 x 1.4mm weighing 0.191 Kg/RM respectively. The main and cross T section shall be jointed at junction crossing with anodised aluminium angle bracket of size 15 x 15 x 1.5mm weighing 0.12 Kg/RM fixed with suitable MS bolts, nuts and washers. The snap grid shall be supported at ends all along with wall with anodised aluminium angle of size 40 x 25 x 2mm wieghing 0.36Kg/RM fixed to wall with suitable arrangements and providing 12mm thick semi perforated particle board in grid and applying two coats of synthetic enamel paint over a coat of pink primer after preparation of surfaces complete all as specified and as directed by Engr-in-Charge

S&F Composite cement ceiling board 4 mm thick in ( 595 mmX595 mm ) pannel (Make-everest or as approved ) designer ceiling conforming to IS 14862 type B cateogory three incl GI frame , grid work,hold fast,suspended with suspender along with holding down bolt complete . (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with holding down bolts suspenders and adjusters

S & F in replacement curtain rod 20 mm dia, mild steel, chromium plated, fancy type with fixing brackets and knobs at both ends as per site requirement complete all as specified and directed by Engineer-in-Charge. Note:- The cost of brackets and knobs is deemed to be included in the quoted rate. Nothing extra shall be paid on this account.

M&L for 2nd class hard wood plain,solid straight chowkhats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints.

S&F 1.25 mm thick Pressed steel frames of size 125mm x 60mm for single doors including necessary fixing lugs, hinges, lock strike plate, etc complete all as per IS provns.

S&F 1.25 mm thick Pressed steel frames of size 105mm x 60mm for single doors including necessary fixing lugs, hinges, lock strike plate, etc complete all as per IS provns.

S&F 2nd class hard wood 35mm thick plain framed panelled factory made shutter two panels with lock rail and panels of 9mm BWP commercial ply or 12mm veneered partical board with veneered veneering on both side .size of rails as pes IS-1003 kiln seasoned and chemically pressure treated comp all as specified.

S&F IInd class hard wood glazed and skeleton shutters 35mm open rebated and prepared to receive glass, gauze etc, without sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part I section 8, clause 8.20 (a) supplied and fixed to chowkats

S&F 25 mm thick Flush shutters for cupboards solid core construction, with block board core, and ply wood face panels, both faces covered with decorative face veneer with lipping to match complete all as specified and as directed by Engineer-in-Charge.

S&F Prelaminated partical board 19/20mm medium density ,prelaminated with one side with decorative choice laqmination and other side balancing with white lamination , stitched with20 mm thick wooden bead all around fixed with screws as in shelves to kitchen almirah and cub board fixed in repair.

S&F 12 mm thick plywood, 5 ply grade BWE, type BB fixed with screws to timber frame work with 0.9mm decorative laminate type 1 of surface finish, colur and pattern as approved fixed with approved adhesive as per maker,s instructions

S&F factory made mild steel Window box type with side huge shutters incl pintol hinges,steel handles, steel peg stay and all locking arrangement and one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBTZ/TD/888R & 889 ii) MS fillets, glazing, wire gauge shall be measured and paid separately iii) opening incl provn shutter for cooler to be provided

S&F Steel windows with side hung shutter incl box type hinges with steel handle handle of MS flat welded to the frame incl.MS 100dia tower bolt welded to the frame over a piece of MS flat and peg stey with glazing bars . Making good and fixing of windows with P.C.C 1:3:6 Type C-2 included in the item

S&F Steel windows with side hung shutter incl box type hinges with steel handle handle of MS flat welded to the frame incl.MS 100dia tower bolt welded to the frame over a piece of MS flat and peg stey without glazing bars .Making good and fixing of windows with P.C.C 1:3:6 Type C-2 included in the item

S&F Steel ventilators or windows fixed type with glazing bar.Making good and fixing of windows with P.C.C 1:3:6 Type C-2 included in the item

S&F framed work such as grills ,framed guard bars barred iron doors ;ladders framed balusters railings and similar work conforming to Fe 410-0or Fe 310-0

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and approved.

S&F factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the frame at site as per specification.

S&F anodised aluminum door window frames ,other sections for doors , windows , ventilatorswith one or more rebates , channel for sliding shutters , grills etc including jointing cleats for fixing etc , complete all as specified. .

S & F in repair aluminium channel with rubber gasket of suitable size and thickness as required at site for fixing glass in aluminium door/windows complete all as specified and directed by Engineer-in-Charge.

S&F in repair sheet glass 5.5 mm thick ordinary quality & glazing with rubber gasket in squares exc 0.5sqm in each pane as in aluminium door/window complete all as specified and directed by Engineer-in-Charge.

S&F Aluminium anodised barrel tower bolt of extruded section of 150mm

S&F mild steel butt hinges medium weight cold rolled mild steel of 100mm

S & F in Repair Piano Hinges mild steel ,bright finish width of flaps open in 40mm all as specified and directed by engineer in charge

S&F Aluminium handles cast type anodised of 150mm

S&F mild steel sliding door bolt plate type stove enameled black with bright bolt not less than 12mm dia with and incl. A minimum of 6bolts and nuts four on bolt plate and two on staple plate of 250mm long.

S&F mild steel barrel tower bolt ,stove enamelled black with bright bolt of 150mm

S&F mild steel pressed handles oval type stove enamelled black of 150mm

S&F in repair 300mm mild rat tail rod pattern springs including roller and, roller plate and welded to chowkhats and taking down old unservicabale spring, complete all as specified and directed by Engineer-in-Charge.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F as in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F Sheet glass 3mm thick ordinary quality and glazing with oil putty in square not exc.0.5sqm in each pane

S&F in repair MS steel window handles (left/right) fixed to steel windows including reveted / welding if required complete all as specified by Engineer- in - Charge.

S&F in repair, MS peg stay for steel window complete all as specified by Engineer- in - Charge.

M&L for welding in repairs n.exc 2.5 cm in length and not exceeding 6mm thick of metal complete all as specified and directed by Engineer-in-Charge.

S&F in repair Hasp and staple 100mm safety type,Aluminium anodised,withmild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified by Engineer- in - Charge.

S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor; overall length of cover plate 150mm complete.

S&F anodised aluminum American handle cast type 200mm for doors all as spfd...

S&F anodised aluminum handle cast type 100mm collapsible type all as spfd...

S&F anodised 75mm size butt hinges , type C21 extruded aluminum alloy ISI marked all as spfd..

S&F 100 mm long Butt hinges extruded aluminium alloy , with galvanised mild steel hinge pin, anodised, type B-21, ISI marked complete all as specified and as directed by Engineer-in-Charge.

S&F Aluminium anodised, barrel tower bolt of extruded section, size 150 mm, complete all as specified and as directed by Engineer-in-Charge.

S&Fal anodised aluminum handle cast type 100mm.

S & F in repair pivot of suitable size and thickness as required at site for aluminium door complete all as specified and directed by Engineer-in-Charge.

S & F in repair for door closer hydraulically regulated , designation No 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 KG and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repair brass 4 lever mortice lock, vertical type size 100mm suitble for existing aluminium door complete all as specified and directed by Engineer-in-Charge.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover, govering pivot made of brass other parts made of mild steel heavy duty and fixed

S&F Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete

Attending complaints of rolling shutters making functional by providing greasing oiling , welding etc.including taking down rolling shutters or hood if required complete all as specified and as directed.

S&F safety lever locks mild steel with 4 levers for rolling shutters

S&F Ball bearing for rolling shutters.

S&F Tubes galvanised medium grade with all fittings fixed to walls or laid in floors 15mm dia.

S&F 20mm bore tubes medium grade galvanised with all fittings and fixed to walls or laid in floors including taking down old.

S&F Rotational moulded polythene ISI marked two layered water storage tank (cylindrical vertical with closed top)hoisted and fixed in position of 500 ltrs incl dismantling including dismantling existing.

S&F Rotational moulded polythene ISI Marked two layered water storage tank (cylindrical vertical with closed top)hoisted and fixed in position of 1000 ltrs incl dismantling including dismantling existing.

S&F Ball valve high pressure of PTMT with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixed fixed in repair.of 20mm Make : Prayag or equivalent.

S&F Ball valve high pressure of PTMT with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixed fixed in repair.of 15mm Make : Prayag or equivalent.

S&F Stop valve cast copper alloy with crutch or butter fly handle screwed both ends & screwed for iron pipe of 15mm dia fixed in repair.

S&F in repairs stop valves cast copper alloy chromium plated fancy type/concealed type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F Bib taps cast copper alloy with crutch or butter fly handle screwed for iron pipe for 15mm bore dia of pipe fixed in repair.

S&F in repairs bib taps cast copper alloy chromium plated fancy type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F Bib taps standard of PTMT any colour high pressure screwed for iron p[ipe and fixed of 15mm fixed in repair Make : Prayag or equivalent.

S&F in repairs pillar taps cast copper alloy with capstan head, chromium plated, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S&F Stop valve cast copper alloy(concealed type) with crutch or butter fly handle screwed both ends & screwed for iron pipe of 15mm dia fixed in repair.

S&F Angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F Vitreous china wash down water closet Orissa pattern white padestal pattern of size 550x440mm including integral foot rest excluding flushing cistern and flush pipe) incl. P or S trap comp all as specified and fixed in repairs. Make Parryware/Cera/Hindware

S&F in repairs PVC flushing cisterns 10 ltrs capacity including flushing pipe and connections complete . Make : CERA ( CAT No: B1010108 , or equivalent in Parryware ,Jaquar, Hindware as approved by Eng-in-Charge .

S&F Plastic water closet seat cover white/coloured ,closed pattern with flat bottom pattern and cover and mild steel chromium plated or aluminium hinging device fixed in repair

S&F wash hand basin vitreous china size 550x400mm white flat back as approved by GE ,waste,chain plug,pvc connection, pvc waste pipe comp all as specified fixed in repair

S&F viterous China urinal half stall type white including CP spreader, waster pipe etc.

S&F PVC connection of PTMT nuts 15x600mm long fixed in repair.

S&F PVC connection of PTMT nuts 15x450mm long fixed in repair.

S&F kitchen sinks with drainage board made of stainless steel 1mm thick with plugs, washers and waster, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and conneting union to pipe overall size 915mm x 460mm bowl size 410 x 330 x 160mm

S&F Chromium plated soap dish complete all as specified and directed by Engineer-in-charge.

S&F Vitereous china wash down water closet pan (Pedestal pattern) white including trap bolts etc complete including connections to drain and anti siphonage pipe.

S&F CP Health Faucet fixed type suitable for EWCs with 1,5 mtr stainless steel tube complete all as specified and directed by Engineer-in-charge of MAKE : JAQUAR, PRAYAG

S&F CP toilet paper holder fancy type complete all as specified and directed by Engineer-in-charge.MAKE: JAQUAR OR EQUIVALENT as approved by Eng-in-Charge .

S&F Towel ring of cast copper alloy chromium plated fixed and repair ( CAT PART NO: BA-02 , MAKE: PRAYAG) or equivalent in Jaquar , Parryware as app by Eng-in-Charge.

S&F two way angle cock of cast copper alloy chromium plated fixed and repair ( CAT PART NO: 7211 , MAKE: PRAYAG) or equivalent in Jaquar , Parryware as app by Eng-in-Charge.

Waste pipe 32mm for WHB with coupling fixed in repairs.

S&F Central hole basin mixer for hot and cold water brass chromium plated screwed down with long sunk and fly nuts screwed for 15 mm dia (( CAT PART NO: 7250, MAKE: PRAYAG) or equivalent in Jaquar , Parryware as app by Eng-in-Charge.

Waste pipe 40 mm for SINK with coupling fixed in repairs.

S& F in repair internal fitting of PVC low level cistern as per existing pattern to make the PVC low level cistern fully functional complete all as specified and as directed by Engineer- in - Charge.

S&F in repair PVC (SWR) floor trap plain 75mm dia with PVC grating including jointing with solvent cement complete all as specified and directed by Engineer- in - Charge.

S&F PVC(SWR)single socketed in any length with rubber ring joint fixed with wall of 110mm as in rain water pipe

S&F PVC(SWR)single socketed in any length with rubber ring joint laid in floors of 110mm as in rain water pipe

S&F PVC(SWR)single socketed in any length with rubber ring joint fixed with wall of 75mm

S&F PVC(SWR)single socketed in any length with rubber ring joint laid in floors of 75mm

S&F PVC SWR branch piece single equal or unequal 110mm with owl access

S&F PVC SWR branch piece single equal or unequal75mm with owl access

S&F PVC SWR S trap laid and jointed to 110 mm bore PVC pipes .

S&F PVC(SWR) bends any radius 110mm. With owl access

S&F PVC(SWR) bends any radius 75mm. With owl access

S&F in repair pvc cowls , 75 mm dia

Cutting chases,pinning in making good to facing where requried and pointing in cement mortar 1:3 to ends or edge of landings,steps,cills,sunshade,shelves, lintel etc. tubes or concealed conduit etc. and making good, cutting not exc 10 cm girth

M&L Preparing new decorated surfaces plastered/unplastered by brooming down etc and applying two coat of distemper oil emulsion on walls inner site including cornices pilasters etc complete all as specified.

M&L Preparing old finished surfaces of walls including cornices, pilasters etc and applying one coat of distemper oil emulsion, white or tinted as directed by the Engr in Charge.

M&L Preparing surfaces of plaster or unplaster new and applying two coat of ccement based paint

M&L Preparing old decorated surfaces treated with cement base paint of walls cornices pilaster etc and applying one coat of cement base paint (Ist quality) in plain pattern on walls complete all as specified.

M&L Preparing surfaces of plaster or unplaster new and applying two coat of white wash on walls.

Ditto but as on ceiling .

M&L Preparing surface of wood of any desc over 10cm width ot girth and applying two coats of synthetic enamel paint

M&L Preparing surface of steel of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer

M&L Preparing surface of steel of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer

M/S ASHRAFI CONSTRUCTION CO

N.K. CONSTRUCTION COMPANY