Construction of Community Hall in ward No. 5 Bholwada Karapur Bicholim under MLA -LAD Scheme in Mayem Constituency.

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m.>All kinds of soil

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering shuttering and finishing in:>All works upto plinth level

Refilling the pipeline/foundation trenches plinth sides foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer in Charge.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1: 4 (1 cement : 4 coarse sand) in foundation and basement.

Extra for laterite masonry in all sizes in superstructure from floor I level upto floor V level.

Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of cement mortar 1:4 (1 cement : 4 coarse sand)>20 mm thick.

Kotah stone slab flooring over 25 mm thick in risers of steps skirtings dado & pillars laid on 12mm (average) thick cement mortor 1:3 (1 cement : 3 coarse sand) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete.

12mm cement plaster 1:3 (1 cement : 3 fine sand)

20mm cement plaster 1: 3 (1 cement : 3 coarse sand)

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering shuttering finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size)>All works upto plinth level

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering shuttering finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size)>In walls (any thickness) including attached pilasters buttresses plinth and string courses fillets columns pillars piers abutments posts and structs etc. upto floor five level

Providing and laying in position (1:11/2:3) Reinforced cement conrete excluding the cost of centering shuttering finishing and reinfrocement (1 cement: 1½ coarse sand:3 graded stone agg 20mm nominal size)>In beams suspended floors roofs having slope upto 15° landings balconies shelves chajjas lintels bands plain window sills staircases upto floor five level

Providing TMT steel reinforcement bars of (SAIL TATA. VIZAG JSW Steel Ltd.) ) (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Centering & shuttering including Strutting Propping & removal of forms for :>Foundations Footings Bases for columns

Centering & shuttering including Strutting Propping & removal of forms for :>Columns Piers Pillars Aburments Posts and struts (square rectangle polygon in plan)

Centering & shuttering including Strutting Propping & removal of forms for :>Sides and Soffits of beams Beam Haunchings Cantilever Girders Bressumers and Lintels plinth beams exceeding 1m in depth

Centering & shuttering including Strutting Propping & removal of forms for :>Suspended floors roofs landings shelves & their supports

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade.

Painting three or more coats with acryllic exterior paint of approved brand and manufacture (Such as Dulex/ Asian Paints/ Sherwin Willians) including applying one coat of cement primer and one coat of surface treatment etc. complete.

Providing and fixing M.S. grill of required pattern in wooden frames of Windows etc. with M.S. flats square or round bars with round headed bolts and nuts or by by screws.>Plain grill

Providing and fixing anodised aluminium shutters in accordance with the specification annexed herewith including transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: windows with two sliding shutters using 18 mm series shutters section.>Figured glass

Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section

Providing and fixing anodised aluminium shutters in accordance with the specification annexed herewith including transportation, scaffolding and handling etc. complete as per direction of the Engineer-in-charge: Openable windows and ventilators using 18 mm series shutters section.>Acrylic sheet

Extra for powder coating with pure polyester powder of shade of required colour on the aluminium section

Painting one or more coats with superior quality ready mixed paint of steel work of approved brand & manufacture in all shades on old work to give an even shade.

Providing woodwork in frames of doors windows clerestory windows trusses & other frames wrought framed and fixed in positon.>Second class Indian teak wood

Providing and fixing 35 mm thick panelled glazed or panelled and glazed shutters for doors windows and clerestory window including anodized aluminium butt hinges with necessary screws:>Second class Indian teak wood

Single Colour Foam Core FRP (Fiber Reinforced Polymer) Door Shutter Manufacture Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system with seasoned hard wood moisture less than 17% wood styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) . The core of shutter will be filled as specified (Expanded Polystyrene Foam / Polyurethane Foam (EPS/PU) Foam). The shutter to be of single colour & water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (R V Engineering College Bangalore & Technology Information Forecasting & Assessment Council) technology in line with IS 13034 1990 test Standard in an ISO 9001 – 2015 certified factory. Accessories: i) S. S. Hinges 4” - 3 Nos ii) S. S. Latch - 1 No iii) Tower Bolt 5” - 2 Nos iv) Handle 5” - 2 Nos Note: For 35 & 40mm thickness shutters only frames of 5 x 2 ½ Cross section frames to be used.>Shutter Thickness>35mm

Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins rafters trusses flashings etc. complete as per the directions of the Engineer in charge.

Add for providing & fixing Flashings -[Corners Ridges valleys gable end & Trims] (Girth upto 610mm) including all the accessories complete as per the directions of the Engineer in charge.

Steel work welded (SAIL TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only)in built up sections trusses and framed work including cutting hoisting fixing in position and applying priming coat of red lead paint.>In tees angles flats and channels

Providing and fixing vitrified antiskid tiles (320x320) and 10mm thick tiles in floor treads of steps landing on 25mm thick bed of cement mortar 1:3 and jointed with cement slurry complete.

Providing and and laying vitrified floor tiles in different sizes of Johnson Somany Kajaria (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc. complete>600x 600 mm Dark Shades

Proving and fixing white vitreous china water closet squatting pan (Indian type w.c. pan) size 580 mm with 100 mm sand cast iron P. or S trap 10 litres high level P.V.C. flushing cister (of approved make) with fittings rack bolts 32 mm diameter P.V.C telescopic flush pipe with fit tings and clamps 25mm P.V.C. over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon pull complete cutting and making good the walls and floors where required.>Long pan pattern W. C. Pan

Providing and fixing vitreous china wash basin with RS or C.I. brackets painted white 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern 32 mm diameter M.I. or C.P. brass trap and union complete including cutting and making good the walls where required.>Flat back wash basin size 630 x 450mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc.>15 mm dia nominal outer dia pipes.

Providing and fixing chlorinated polyvinyl chloride (CPVC) pipes confirming to IS: 15778 having thermal stability for hot and cold water supply includng all CPVC plain and brass threaded fittings CPVC solvent cement trenching refilling and testing of joints complete as per firectionof the Engineer in charge.(External work (heavy duty SDR 11 pipe)>32 mm nominal outer dia pipes.

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson Somany Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours shades except burgundy bottle green black of any size as approved by Engineer-in-charge in skirting risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete.>Wall Ceramic Glazed Tiles : 200 x 300

Providing and fixing NICKEL chrome plated copper alloy Fancy long body bib cock with wall flance Jaquar make or equivalent. Confirming to IS 8931>1993>15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy concealed stop cock with slinding flance 15 mm Jaquar make or equivalent. Confirming to IS 8931>1993>15mm nominal bore

Providing and fixing Hand Shower (Health Faucet) with 8mm dia ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards.

Providing and fixing rigid PVC S.W.R. (soil waste & rain water drainage pipes of approved including lubricant etc. complete (single/double) socketed:>110 mm dia

Providing and fixing rigid PVC bend of required degree (of approved make) for S.W.R. drainage pipes of approved including lubricating.>110 mm dia

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1: 1 1/2:3 mix (1 cement: 1 1/2 coarse sand >3 graded stone aggregate 20mm nominal size foundation concrete 1:1 1/2:3 mix (1 cemet >1 1/2 coarse sand :8 graded stone agrregate 20mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design.>Inside size 60 x 60cm and 60cm deep including C.I. cover with frame (light duty) 455x610mm internal diameter total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg).

Providing and fixing in position S.S. hand rail in main stair case and landing as per approved design shown in the drawing including bending handrail pipe to proper shape in curves with specials etc. complete.

Precast plain Cement Tacktiles 32mm thk of required shade in floors treads of steps and landing laid on 25mm bed of cement mortar 1:4(1cement:4coarse sand) jointed with neat cement slurry with pigment to match the shade of tiles including rubbing and polishing complete.

Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701> 1996.>1000 lit. Capacity

Making soak pit. 2.5 m dia 3 m deep with 45x45 cm dry brick honey comb shaft and S.W. drain pipe 100 mm diameter 1.8 m long complete filled with laterite stone aggregate 125 to 180 mm surrounded by laterite stone aggregate of 40 mm and down gauge as per standard design.

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleats with C. P. brass screws and washers.

Providing & fixing soap dish chromium plated with brackets fixed to wooden cleats with CP brass screw

Providing and fixing Prince or equivalent make PVC SWR half round eaves gutter with bolts nuts and flat iron brackets 40 x 3 mm size complete.>250 mm nominal size

Please Enable Macros to View BoQ information