PROVN OF TILING AT JCOs QTRS JP 12 1 JP12 2 THREE PHASE COMMERICAL MAINS AT UHF DET BLDG NO CH30 STAIR ALONG WITH COVERED FOOTPATH SMB02 ATT LINE TO NRES-7 RHQ LINE UNDER GE GANGTOK

Amount

Demolition of concrete in ground floor and pavings n.exc 15cm thick (un reinforced) (below or above ground level) complete all as specified.

M&L for 25 mm thcik PCC (1:2:4) type B1 (20mm graded stone aggregate), finished concrete surfaces even and rough to receive floor finishes complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls incl raking joint hacking for key ,scrubbing down with water etc all as directed.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick(square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match,over and Incuding 15mm thick screed bed with CM 1:6 complete in floor for receive the tiles complete all as specified and as directed.

Taking down shutters and refixing in same opening of any description exc 1 Sqm but not exc 2 Sqm each complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match,over and Incuding 15mm thick screed bed with CM 1:6 complete in floor for receive the tiles complete all as specified and as directed.

All as per item No 6 here-in-above but in skirting with 7-8 mm thick backing coat in CM (1:4) complete all as specified and directed.

Excavating in post holes (or similar holes) each n.exc 0.5 Cum getting out,returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm watering and removing surplus soil to a distance n exc 50m and making good surface (soft/loose soil) complete all as specified and directed

S&F rolled section as in main and cross beams hip, jack rafters, hollow section purlins, where connected to common rafter and running rails and guides for slidding doors fixed with angle cleats or other connecting plates of grade Fe-290 Gde E165 etc, complete all as specified and directed

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile stregth of 550 mpa as in roof covering fixed with self tapping screws complete all as specified and directed

M&L for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile stregth of 550 mpa as in roof covering fixed with self tapping screws complete all as specified and directed

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer to steel surfaces of any description over 10 cm in width or girth including preparation of new steel surfaces complete all as specified and directed

Demolition of brick or stone boulder masnory, built in cement mortar including all quoins arches, pillars, etc but excluding ashlar facing, dressed stonework and precast concrete articles complete.

M&L for walling of randowm rubble, uncoursed, well bonded, bedded and solidly hearted built in built mortar (1:6) complete all as specified and as directed.

M&L rendering 15mm thick in CM 1:6 on other than fair faces of brick or concrete surfaces finished even and smooth with out using extra cement all as specified and directed.

M&L for applying two coats of cement base paint on new/old plastered wall surface including preparation and previously untreated surfaces of wall complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed.

Surface excavation n exc 30 cm deep and averaging 15cm deep and getting out in soft /loose soil complete all as specifed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

Returning, filling in, including spreading levelling watering and well ramming in layers not exceeding 25 cms in thick as in soft/loose soils complete all as specified and directed.

Removing surplus soils to a distance not exceeding 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and directed.

M&L for precast PCC 1:3:6 type C1 (by using 20mm graded stone aggregate) block masonry with solid blocks 10 cm in width and setting in CM 1:6 complete all as specified and as directed.

M&L for PCC (1:3:6), type C-1 (using 20mm graded stone aggregate) as in coping complete all as specified & as directed

M&L for formwork to sides of concrete foundation, footings, bases of columns, raft and raft beams, sides & soffits (if any) foundation and plinth beam for rough finished surfaces of concrete complete all as specifed & directed.

M&L RCC (Nominal mix) type B1, 1:2:4 using 20mm graded stone aggr as in Foundations, including rafts, footings. foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed

M&L for formworks to sides and soffit of floor roof beam, beam haunching, girders, bressummers, lintels, cantiliver shelves including support overhangs etc also splays between floor and beam etc complete all specifed and directed.

M&L for RCC 1:2:4 (nominal mix) 20mm graded aggregate as in beams, cantilevers, bressumers, lintels over 1.5m span complete all as specifed and directed.

M&L for TMT bars 10mm dia and over cut to length bent to shape required incl, cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips conforming to IS:1786 complete all as specified and as directed.

M&L for MS bars 5mm dia and over upto and including 10mm in sitrrups cut to length, bent to shape required incl cranking bending spirally for hooping for columns, hooking ends and bnding with and incl mild steel wire (annealed) not less than 0.9mm dia quality conforming to TMT bars complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40mm stone agg) as in plinth protection, path/hardstanding finished cement concrete surfaces fair and even including forming construction joint filled with CM (1:6) all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) in two layers of 10mm and 5mm (outer layer CM should be added with liquid WPC) on fair face of brick or concrete surfaces complete all as specified and directed.

Supply only liquid water proofing compound

M&L for hard core of gauge n.exc .63 mm deposited spead, levelled, watered well rammed to a uniform surface n.exc 15 cm thick using broken stone or boulder complete all as specified and as directed.

M&L for 100 mm thick cement concrete 1:2:4 type B-2 (using 40mm graded stone aggregate) as hardstanding/flooring/path etc and finishing the surface even and fair etc complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate finished and even as in copping layer of floor complete all as specified and as directed.

M&L Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick rendering in CM (1:4) complete all as specified and as directed.

S&F rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postion (cylindrical vertical with closed top) hoisted and fixed in postion 500 ltrs capacity complete all as specified and directed.

M&L for 15 mm bore steel tubing medium grade galvanised with all fittings complete to walls & laid in floors complete all as specified and as directed.

M&L for 20 mm bore steel tubing medium grade galvanised with all fitting complete to walls & laid in floors complete all as specified and as directed.

S&F for 15mm chromium plated angle cock with flange complete all as specified and directed.

S&F toilet roll holder with flap CAT No AKP-CHR-35753P

S&F Health faucet with 1 mtr flexible tube and wall hook CAT No. ALD-CHR-573.

S&F valve brass 20mm dia high pressure with polythene float and fly nut complete secrewed for iron pipe brass ferrule etc all as spcified.

S&F Gun-metal, globe or gate valves 20mm bore GI pipe with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

S&F of pillars taps, fancy type, cast copper alloy with capstan heads, chromium plated, screwed down high pressure scewed for iron pipe 15mm bore of Make ESSCO Cat Part No SQT-508KN or equivalent.

S&F Soild PVC door frame of size 50mm X 47mm made out of 5mm plain clour PVC sheet reinforced with MS square tube supplying & fixing in opening as per specification and drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm th (style) consisting of frame made out of MS tubes for top & bootom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rails on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the stiles & rails with suitable PVC sheet beading & joined together with solvent cement suppling & fixing in the frame at site as specification & drawing given on MES schedule Part-II (2020) complete all as specified and directed.

S&F aluminum window and ventilator shutter, fixed type without sash bar, aluminum section weighing 0.55 kg/m including necessary joining cleats, glazing clips, 4mm thick glass/AC board/particle neoprene packing incl aluminium grill and anodised aluminium snap beading screws etc. complete all as specified and directed.

M&L for applying two coat of white washing including preparation of new or previously untreated surface of ceiling complete all as specified and directed.

M&L for applying two coats of exterior acrylic emulsion painting over a coat of alkali resistant primer including scaffolding upto 15m ht and preperation of old/new surfaces all as directed.

M&L for 150 mm long aluminimum handles cast type, anodised complete all as specified and as directed.

S&F for 150 mm long aluminimum anodised barrel tower bolt complete all as specified and as directed.

S&F for 75mm size mild steel butt hinges medium weight.

S&F CP towel rack, size 600mm long with lower hanger type complete (Make : Jaquar coe AKP-35781PS)

S&F designer corner glass shelf 25 x 25 cm with CP steel frame complete (Make Jaquar Code ACN : 1173 or equivalent)

S&F 150mm bore PVC (SWR) bends any radius complete all as specified and directed.

S&F vitreous china wash down water closet pedestal pattern white with all fittings fixed as in repairs (excluding flushing cistern and flush pipe) including plastic water closet seat, white closed pattern with flat bottom and cover and MS CP aluminium/PVC hinging device complete all as specified and directed.

M&L for Mild Steel round bars 10mm dia and over dia cut to length, bent to shape required incl cranking, bending spirally, hooking/ends and binding with and incl MS wire not less than 0.9mm dia or securing with clips completed all as specified and directed.

S&F powder coated grid frame work for false ceiling comprising of the following sections for making partitions of 600 x 600m size fixed to walls with rawl plugs & screws and hanged to roof with and including 1mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 28mm x 23mm x 0.3mm thick cross tee shall be 24mm x 23mm x 0.3mm thick and wall angle shall be 20mm x 20mm x 0.3mm thick complete all as specified and as directed.

Supply and fix 4mm thick Non asbestos fibre cement building boards (E- board) of approved texture, for insulation and acoustic purpose of size 595 x 595 mm size fixed with staples on snap grid as in ceiling with and including dusting of surfaces and applying two coats of oil emulsion distemper over a coat of primer including preparation of surfaces complete all as per manufacturers instructions specifed and directed by the Engr-in -Charge.

M&L for chequred cement concrete tiles of size 200mm x 200mm x 25 mm/ 300 x 300mm x 25 mm thick as in pavement/footpath/trade/riser, set and jointed in neat cement slurry and pointed with grey cement and pigment laid over and including screed bed/bedding layer of 15mm thick in cement mortar (1:4) complete all as specified and as directed

Supply and fix PVC connection 15mm size with PTMT nut of length 600mm complete all as specified and directed by Engr in Charge. Make Prayag Cat No 323 or equivalent.

M&L for PCC 1:3:6 type C-2 (by using 40 mm graded stone aggregate) as in bed to drain pipes 150 mm bore, including packing under and haunching against the sides pipes after they are laid and tested, complete all as specified and directed.

Supply & fix 150 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall with necessary clamps,bolts, bends, tee etc.complete all as specified and as directed

M&L Cutting into 150mm dia existing manhole for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B:1 smooth finished, and reforming benching as requiered complete all as specified and as directed.

M&L for pre cast RCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in manholes covers etc including necessary form work and set in CM 1:4 complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed with wall etc complete all as specified and as directed.

Supply & fix, 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to wall with necessary clamps,bolts etc.complete all as specified and as directed

S&F for PVC (SWR) 75mm junction single (Single T) equal or unequal.

S&F for PVC (SWR) 110mm junction single (Single T) equal or unequal.

S&F for 110mm bore PVC (SWR) vent cowl fixed in position complete all as specified and directed.

S&F PVC (SWR) 75mm access door.

S&F PVC (SWR) 100mm access door.

Dismantling wall and ceiling board (fibre pulp, insulation etc) or insulation boards any thickness including cover fillets.

Dismantling of floor, earth or wall tiling including cement mortar bedding (but not backing) and removal of dismantled materials/rubbish from site complete all as specified and directed.

Taking down shutters of any description and size exc 1 Sqm but n. exc 2 Sqm complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area exc 1.5 sqm but n.exc 4.0 sqm all as specified and as directed

M&L for preparation of new plastered surfaces of walls applying two coats of distemper, oil emulsion, white or tinted over new wall surface and applying 02mm thick wall care putty complete all as specified and directed.

M&L for preparation of complete removal of existing treatment on old plastered surfaces of walls applying two coats of distemper, oil emulsion, white or tinted over old wall surface on a coat of 2mm thick wall care putty, complete all as specified and directed. (putty shall be paid and measured seprately)

Hacking out old broken glass any thickness, size, quality or description from wooden frames glazed with putty

Supply and fix Flush shutters, 35mm thick solid core construction, with particle board core with both face is covered with deco rative face veneer with lipping/frame to match the colour of the frame complete all as specified and directed.

M&L for 2nd class Plain fillets, square, rectangular or triangular in section, clean sawn, of sec area exc 6 & n.exc 13 Sqcm secured with nails or brads.

S & F MS butt hinges 100mm long complete.

S&F 250mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium complete all as specified and as directed.

S&F 3mm thick, sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane.

S&F in repair stain less steel wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanished wire staples complete all as specified and directed.

M&L preparation of old or previously treated wooden surfaces of any descripting over 10 cm width or girth and applying one coat of synthetic enamel paint over wooden surface complete.

S&F vetrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed or bedding layer in CM (1:6) all as specified and directed.

Ditto all as item No 89 above but on vertical surface of wall like skerting/dado/riser of steps etc on 15mm thick rendering complete.

Supply and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPD rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per

S& F 5.5mm thick glass pane area exc 0.5Sqm but n exc 1Sqm fixed on aluminium frame work of appropriate section as directed by Engr-In-charge.

Supply and fix in repair, 10 litre capacity low level PVC flushing cistern (white), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and directed.

Supply & fix in repair two way Bib tap, long body cast copper alloy, chromium plated with crutch or butterfly handle with healthfuceset, with ABS body with 1Mtr SS braided connection pipe screwed down for 15mm bore GI Pipe or for brass ferrule.

Supply & fix in repair Bib tap, long body cast copper alloy, chromium plated with crutch or butterfly handle, screwed down for 15mm bore GI Pipe or for brass ferrule including taking down old unserviceable one.

Supply & fix in 15 mm bore dia angular Stop cocks, cast copper, fancy type, chromium plated, with wall flange screwed down, screwed fro iron pipe or union and complete all as directed.

Supply and fix corner glass shelf 225x 225mm with CP steel frame complete all as specified and directed.Make CERA cat part NO: F5005102 or equialent.

S&F PVC connections 15mm size with PTMT nuts of length 450mm

S&F vitrous china white colour flat back wash hand basin (Full padestalpatern) of size 540mmx 395mmx185mm fixed with and including fixing accessories like CP wastcoupling(half or full threaded,waste pipe etc complete.Make CERA cat part No:S2040105 & S2090101 complete all as spd and directed by the Engr In charge.

Supply and fix in repair cromium plated wall mixer with telephone shower arrangement only with crutch (with Bush & piston Divertor fittings with aerator) and Chromium plated shower pack (single flow 70mm roundshape hand shower with 1.5M long spirocrome flex hose & wall bracket. Make ESSCO Cat Part No : SQT-517KN and SAE-551SH555.

S&F cromium plated central hole basin mixer extended casted spout with 450mm long braided hoses complete. Make ESSCO Cat Part No SQT-516KN

S&F in repair stainless steel towel rail 600mm long. Make ESSCO: Cat Part No AEC-1111N

Taking down 15mm dia steel tubing and connections, including cleaning and refixing or removal to store complete all as directed.

Supply & fix in repair 75mm dia PVC floor trap of outlet, with grating, including jointing to waste pipe fixed in PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) complete all as specified and as directed.

Material and labour for Decorative laminate 0.9mm thick type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's insturctions.

S&F decorative type curtain rod, chromium plated 25mm dia with fixing brackets, stops and complete fittings including making good the surface were damaged all as directed by Engr-in-Charge.

M&L for PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in coping complete all as specified and as directed.

S&F of Mild steel works as in posts, struts, etc in fencing including cutting tops to shape as directed drilling holes notching for wire etc, flat iron fillets/horizontal bars etc including necessary drilling, welding, bolting or riveting etc complete.

S&F of Mild steel screw bolts (Machine Made) with hexagonal heads, bolts washers etc (5 to 10mm dia) length of bolt exc 5cm and n.exc 10cm long completed.

S&F PVC coated chain link fencing of mesh size 50 x 50 made out of 3.5mm dia GI wire (2.5mm dia wire and 1mm thick PVC coating) fixed to any type standard rail, staining bolts etc completed.

S&F Galvanished, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm barbs at 75mm spacings and straining and fixing to any type of standard rails strainging bolts, including, securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc as directed (each line wire to be measured).

M&L for two coats of synthetic enamel paint over a coat of red oxide primer to surfaces of any description n.exc 10cm in width or grith incl preparation of new steel surfaces complete all as specified and directed.

Supply,laying jointing and testing in trenches or passing through pipe, 1100 Volts grade XLPE insulated, screened PVC bedded, galvanized steel strip or wire armoured LT electric power under ground cable conforming to IS:7098 (Pt-1)-1988, heavy duty electric cable with aluminium conductor of cross sectional area 70 Sqmm 3.5 core with necessary fixing arrangements such as lugs, glands and terminal etc complete all as specified and as directed Make Havells/Polycab

Supply and laying DWC pipe SN-4 with coupler 50 mm OD, ISI marked along with all accessories like socket, bend, couplers etc. Conforming to IS 14930, PartII complete with fitting and cutting, jointing etc. Laid in trenches/fixed to pole /laying under road crossing /fixed on pavement wall with clamps complete all as specified and as directed. Make Jindal/Telerex/MASTODON

M&L for Excavation in trenches n. Exc 1.5 mtr wide and n.exc 1.5 mtr depth for laying of cable/ foundation of pole and getting out in loose /hard /rocky soil complete all as directed

M&L for Returning filling in loose /hard /rocky soll including spreading, levelling, watering and well ramming in layers not exceeding 25cm complete all as specified

M&L for Removal of surplus excavated (soil) to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.50 m above the starting point complete all as specified

S&F 4 Pole MCCB 125 Amps, 50 Hz, 415 Volts rupturing capacity 35 KA with Adjustable ocerload, Short-circuit,Ground fault(4 Pole) & fixed Instantanous Netural Proection complete all as specifieds and directed by Engr-in-charge. Make havells cat part no IHLEFN40125 OR EQUIVALENT IN Legrand/L&T

S&F Sheet Mettal enclosure suitable for MCCB of capacity 4 Pole 125 Amps ,50 Hz 415 volts Make complete all as specifieds and directed by Engr-in-charge Make havells/Legrand/L&T

Supply and laying Galvanized Iron pipe light grade of dia 50 mm for cable protection in trenches /ducts/floor or fixed on walls /roof/poles etc including suitable fixing accessories complete all as specified and directed Make Tata /Jindal/prakash.Note:- Wherever the protection pipes are to be laid/fixed on poles/walls/other surface the cost of clamping using appropriate size/type of MS clamps nuts,bolts etc is deemed to be included in the unit quoted rates.

M&L for cutting the existing hard standing/PCC/WBM road at a depth not less than 45cm and 25cm in width for passing of cable through GI pipe, returning filling in, complete including finishing the surfaces by providing cement concrete (1:2:4) type B-2 (using 40mm graded stone aggregate) up to 20 cm depth, finising to a uniform smooth surface to match the existing surface complete all as specified and directed. Note; (i) GI pipes shall be measured and paid separately (ii) Any damages made /caused to the HT/LT cables, Water supply pipe lines,OFC cables etc during the excavation work shall be made good by the contr as per original & to the entire satisfaction of of Engr-in-charge. Cost of the same is deemed to be included in the unit quoted rates.

Supply, laying, jointing and testing in trenches or passing through pipe, 1100 Volts grade XLPE insulated, armoured heavy duty electric cable with aluminium conductor of cross sectional area 10 Sqmm 2 core with necessary fixing arrangements such as lugs, glands and terminal etc complete all as specified and as directed Make : Havells/Polycab

Supply and laying DWC pipe SN-4 with coupler 40 mm OD, ISI marked along with all accessories like socket, bend, couplers etc. Conforming to IS 14930, Part-II complete with fitting and cutting, jointing etc. Laid in trenches/fixed to pole /laying under road crossing /fixed on pavement wall with clamps complete all as specified and as directed. Make Jindal/Telerex

Steel tublar swaged poles complete with cast iron base plate finial taper plug, bolts, nuts & screws as specified type 410 SP-22 (8.5 meters long)

Supply and fixing LED street light fitting 60 watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65 /66 protection and impact resistance of IK07 complete GI bracket 1.5m long made out of GI dia suitable for fixing street lights bend to suitable radius incl 2 sets of clamps nuts bolts washers incl painting with aluminium paint etc complete all as specified and as directed. Make Havells/Philips

S&F in repair, Street light cable junction made of polycarbonate, "halogen free and weather proof"for outdoor installation (with metric knockouts for cable entry) IP-66 protection including short cable entry gland thread type with lock nut, four way terminal, GI flat strip clamps of size 25mm X 3mm with bolts,nuts and washers for fixing with MCB one 06 Amps inside the junction box complete all as specified and as directed. Make HENSEL Cat No DK 1010B or equivalent model of Havells/Sintex

Supply & fixing 1.5 Sqmm 3 Core, 240 volts Copper conductor cable heavy duty PVC insulated, round sheathed ISI marked in PVC conduit all as specified and as directed

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, inlcuding fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and as directed.

M & L for point wiring with 1.5 Sqmm PVC isulated unsheathed single core stranded copper conductor (FRLS) cable of working voltage 1100 Volts grade conforming to IS-694 pt-I & II of 2000 drawn in and including 25 mm size PVC casing caping (Double lock) with all casing capping fittings & accessories with 1.60 mm thick pressed steel or mild steel sheet sunk box covered with 3mm thick backelite sheet fixed with brass screws & cup washers including 1.5 sqmm PVC insulated unsheathed single core stranded copper conductor (FRLS) cable as earth continuity conductor connected to main switch/ DB's or common earth dolly complete for light point/ fan point/ exhaust fan point / call bell point controlled by one switch 5/6 AMP one way complete all as specifed and directed.

All as per item No 130 here-in-before but for one socket outlet 3 pin 5 amps independent board.

All as per item No 130 here-in-before but for one 3 pin socket outlet 5 amps on the same board with other switches

All as per item No 130 here-in-before but one bell/buzzer point controlled by one push button on the same board with other switches or independent

All as per item No 130 here-in-before but one light point controlled by two switches.

All as per item 130 here-in-before but for one socket outlet/metal clad socket of 15 Amps fixed on independent board with 2.5 Sqmm multistandard copper conductor wire FRLS PVC insulated and 2.5 Sqmm copper conductor wire FRLS PVC insulated using as earth wire complete all as spcified and directed by Engineer-in-Charge

All as per item 130 here-in-before but for one socket outlet/metal clad socket of 15 Amps fixed on independent board with 4 Sqmm multistandard copper conductor wire FRLS PVC insulated and 4 Sqmm copper conductor wire FRLS PVC insulated using as earth wire complete all as spcified and directed by Engineer-in-Charge

S&F in repair switch piano, flush type 6 amps 230 volts, single pole one way (ISI marked) complete all as directed.

S&F ceiling rose, PVC/polycarbonate insulated body, 3 terminal and 240 volts, ISI marked complete all as specified.

S&F in repairs sheet metal enclosure for 8 way Distribution Boards (DB’s), single pole and neutral double door with IP-43 protection suitable for fixing MCB's/lsolators after and including taking down old DB with MCB complete all as specified and as directed.

S&F in repairs MCB, single pole & neutral, 40 to 63 amps, 240 volts, 10 KA complete all as specified and as directed

S&F in repairs MCB single pole 6 to 32 Amps, 240 Volts, 10 KA rapturing capacity, 'C' Curve complete all as directed by Engineer-in-charge. (Make : Havells/legrand/C&S equivalent of approved make)

Supply & fix lamp holder angular/straight insulated body, with back plate suitable for battern futtings, white/ivory finish complete all as directed.

Supply & fixing LED tube 4 feet light fitting 1 x 18 W, 220 V AC decorative box type with dirver, holder including LED tube light connecting up with three core flexiable copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED bulk head fittings of 10 watts, presure die cast housing 2 crylic diffuser and frame with IP 66 protection complete all as specified and as directed.

M & L for earthing in repairs complete with galvanized steel earth plate electrode 600x600x6 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less 1.5 mtr deep below normal ground level connected to GI earth wire 4 mm dia connected to earth plate by means of nut, bolts, check nut & washer of galvanized iron or of steel, GI earth wire will be protected by 15 mm dia GI pipe 'light grade', watering pipe 20 mm dia GI 'light grade', GI wire meshed funnel, alternate layer of char coal and salt on all side to earth plate upto thickness of 150 mm, filling of black cotton soil in earth pit upto ground level, PCC chamber recessed for and including RCC cover including all necessary excavation & earth work, earth wire connected to O/H continious earth wire on pole, testing the earthing after completion all as specified and shown in electric plate No 3 of MES SSR Part-I 1991 print and as directed .

Supply and fix socket outlet 2 in 1, 3 pin, 6 AMP 230 Volts, 50 Hz, ISI marked all as specified and as directed. Make Havells/legrandor or equivalent.

Supply and fix socket outlet 2 in 1, 3 pin, 6 AMP and 16 AMP flush type 230 Volts, 50 Hz, ISI marked all as specified and as directed. Make Havells/legrandor or equivalent.

Supply and fix switch piano flush type single pole, one way 16 Amp 230 volts, 50 Hz, ISI marked all as specified and directed. Make Havells/legrandor or equivalent.

Supply and fix switch piano flush type single pole, two way 16 Amp 230 volts, 50 Hz, ISI marked all as specified and directed. Make Havells/legrandor or equivalent.

Supply and fixing Buzzer Ding Dong AC 230 volts single pole with suitable fixing arrangement complete with all accessories all as specified and directed.

Supply and fixing LEDZ inverter batten 1x20 watt 220 V, AC decorative box type with backup time up to 3 hrs, auto cut-off after full battery charging, LED tube light connecting up with three core flexible copper conductor cable of suitable size complete all as specified. Make Bajaj SKU Code 830414 or equit havells/Philips

Supply and fixing LED light fittings mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing LED lights fitting 1x9/1x10 W 220 V, AC bulk head luminaries including holder including LED driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified. Make Havells/Bajaj/Philips

Taking down and refixing of Geysers storage type after complition of civil work 25/50 ltrs capacity complete with grounding/drilling in wall and Provn of Zinc coated fastner 12mm dia 150mm long x 04 Nos including replace hot & cold PVC pipe complete including nuts/bolt, painting and complete testing all as specified and directed.

S&F single pole & neutral enclosure with a two pin & earth plug & socket complete with one single pole MCB C curve of 20A rating complete all as specified and directed.

S&F for MCB DB SPN 8 ways Double Door 240 Volt with 200 AMP rated bus bar, IP-42 IK-09, metal door, earth bar, neutral links complete incl blanking plates as required & fixed flush to wall/ other surface complete all as specified and as directed. Make :- Havells/legrand/C&S

S&F MCB single pole & neutral SPN 32 Amps, 240 volts, 10KA rapturing capacity, C curve complete all as directed Make :- Havells/legrand/C&S

Supply and fixing LED mirror lights along with fixture, 5 watts with suitable fixing arrangement complete with all as accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size all as specified. Make Havells/Bajaj/Philips

Supply, installation, testing and commissioning of electirc water heater, storage vertical type, BEE 5 star rated, 25 ltr capacity 230 volts AC, 50 Hz comprising of high wattage heating element for instant heating, extra thick SS inner tank or superior 304 grade, rust & shock proof ABS outer body, non-ferrous pressure plate with & including provision of pressure relief valve and grouting bolts suitably flushed to wall or any orther surface including electric connection with 3 core PVC insulated, sheathed, stranded copper conductor cable/flexible chord complete all as specified.Make : - Havells Cat No - Monza DX : GHWBMGSWH0525 or equivalent approved.

Supply and fixing exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz RPM 1200, copper winding of sweep 250mm

KAMLESH ENTERPRISE

M/S S. S CHETTRI AND SONS

SANJAY KAUSHIK

BIJAY MITTAL

M/S ANIL KUMAR THAKUR

DHARMINDER SINGH

RAAJ BANGAR