Minor repair and painting in Farmers Guest House at Dr YSP University of Horticulture and Forestry Nauni, Solan.

Amount

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level complete in all respect as per satisfaction of Engineer-in-Charge.

a) 1:5:10 (one Cement: five sand : ten graded stone aggregate 40 mm (forty milimetre) nominal size.

Providing and fixing Kiln seasoned and chemically treated hollock wood 35 mm thick. glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing 25mm thick pre-laminated medium density fibre board exterior grade (Grade-I) IS: 14587:1998 marked with one side decorative and other side balancing lamination for cupboard shutters edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand including ISI marked nickel plated bright finishing M.S. piano hinges conforming to IS: 3818 marked with necessary screw etc all complete as per the satisfaction of Engineer-in-charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws with 35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size etc. complete in all respect as per satisfaction of Engineer-in-charge. a) Kiln seasoned and chemically treated hollock wood.

Providing and fixing 2nd class teak wood 40mm into 12 mm wooden Chamfered moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing ISI marked oxidized/ chromium plated M.S. single acting spring hinges with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.a)150 mm ( one hundred fifty milimetre)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.

a). 200x10 mm (two hundred into ten milimetre)

b). 150x10mm (one hundred fifty into ten milimetre)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete in all respect as per satisfaction of Engineer-in-Charge.

a). 125mm (One hundred twenty five milimetre)

b). 100mm (one hundred milimetre)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using tube etc. as required. Complete in all respect as per satisfaction of Engineer-in-Charge. a).In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

40 mm (forty milimetre) thick Cement concrete flooring 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20mm (twenty milimetre)nominal size finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing glass strips in joints of terrazo/ cement concrete floors etc. complete in all respect as per satisfaction of Engineer-in-charge.40 mm wide and 4 mm thick

18mm (eighteen milimetre) thick Cement plaster skirting up to all height, with cement mortar 1:3 (one cement : three sand), finished with a floating coat of neat cement etc. as required complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and laying rectified Glazed Ceramic floor tiles (Kazaria / Oreint bell / Nitco make) of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (one Cement : four sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc complete in all respect as per satisfaction of Engineer-in-Charge.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four sand) etc. complete in all respect as per satisfaction of Engineer-in-charge a)25 mm thick (twenty five milimetre)

Grouting the joints of flooring tiles having joints of 3 mm width in different size of tiles/ Kota stone, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing etc. complete as per the satisfaction of Engineer-in-charge.

Providing and fixing 1st quality ceramic glazed floor tiles (Kazaria / Nitco / Oreintbell make) conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dado over 12 mm thick bed of cement Mortar 1:3 (one cement: three sand) and jointing with grey cement slurry @ 3.3Kilogram per Square Metre including pointing in white cement mixed with pigment of matching shade etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete in all respect as per satisfaction of Engineer-in-Charge (tata/ Jindal make). a). 0.63 mm thick with zinc coating not less than 275 gm/m².

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete in all respect as per satisfaction of Engineer-in-charge. a) 0.63 mm thick with zinc coating not less than 275gm/m². (G.I. sheet will be supplied by university free of cost)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion etc. complete in all respect as per satisfaction of Engineer-in-Charge. (i) Single socketed pipes a). 110 mm (one hundred ten milimetre) diameter (Finolex/ D-Plast/ Vectus/ Kisan/ Prayag Make).

Providing and fixing on wall face unplasticised – PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion etc. complete in all respect as per satisfaction of Engineer-in-charge.

a). Coupler 110 mm (one hundred ten milimetre)

b). Bend 87.5° 110 mm (one hundred ten milimetre)

c). Shoe 110 mm (one hundred ten milimetre)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete etc. in all respect as per satisfaction of Engineer-in-Charge.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade etc. in all respect as per satisfaction of Engineer-in-Charge. a) One or more coats on old work.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade etc. in all respect as per satisfaction of Engineer-in-Charge.a) One or more coats on old work

Finishing walls with Acrylic Smooth exterior paint of Required shade etc. in all respect as per satisfaction of Engineer-in-Charge. a). Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface.

Demolishing cement concrete manually/by mechanical means including disposal of material within all leads etc. complete as per direction of Engineer-in–charge. a). Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix).

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within all leads of etc. complete in all respect as per satisfaction of Engineer-in-charge. a). G.S. Sheet

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead etc. as required complete in all respect as per satisfaction of Engineer-in-Charge. a). Of area 3 sq. metres and below

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge a). With cement mortar 1:4 (one cement: four sand).

Renewing glass panes, with wooden fillets wherever necessary complete in all respect as per satisfaction of Engineer-in-Charge. a) Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding.

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.

RAKESH CHAUHAN

abhishek guleria

Rakesh Vasistha