SPECIAL REPAIRS TO BLDG NO P 12 JCOS MD ACCN ELEPHINSTON ROAD OF CAFVD KIRKEE IN GE C KIRKEE

Amount

Taking down chowkats and frame n.exc 1.5 Sqm each of any type including shutters without taking off shutters from the frame and removing from site complete all as specified and as directed.

Taking down chowkats and frame exc 1.5 Sqm but n.exc 4.00 sqm each of any type including shutter wiuthout taking off shutter from the frame and removing from site complete all as specified and as directed.

Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 sqm each and removing to store complete all as specified and as directed by Engineer-in-Charge.

Taking down shutters of any description exc 1.00 sqm but n.exc 2.00 sqm each resecuring, easing, adjusting and re-fixing in same opening after minor repairs including all necessary fittings complete all as specified and as directed by Engineer-in-Charge.

S & F Pressed steel door frame for doors of size 105 x 60mm with single rebate including necessary fixing lugs, hinges, lock strike plate, etc complete with and including hollow section of frame to be filled with PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) complete all as specified and as directed by Engineer-in-Charge.

S & F Pressed steel door frame for doors of size 165 x 60mm with double rebate including necessary fixing lugs, hinges, lock strike plate, etc complete with and including hollow section of frame to be filled with PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) complete all as specified and as directed by Engineer-in-Charge.

S & F 35mm thick plain framed panelled factory made door shutters (two panels) with lock rail and panel of 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge.

S & F 35mm thick 2nd class HW glazed or skelton shutter open rebated divided into square with plain chamfered or rounded mitred and rebated without sash bar and prepared to receive gauze or glaze, size of members as per clause No. 8.20 (a) of SSR pt-1 complete all as specified and as directed by Engineer-in-Charge.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S & F Factory made internal PVC door frame of size 50x47mm single revated made out of extruded 5 mm PVC foam sheet, mitre cut at two corners and jointed with 02 Nos of 150 mm brackets of 15x15 mm MS square tube. The two vertical door profiles are to be in forced with 40x20 mm MS tube of 19 gauge through out the frame complete all as specified and as directed by Engineer-in-Charge.

S & F steel window with side hung shutter incl projecting type hinges with steel handles and steel peg stay complete with glazing bar dovetailed or welded complete all as specified and as directed by Engineer-in-Charge.

S & F steel window with side hung shutter including projecting type hinges with steel handles and steel peg stay complete without glazing bar dovetailed or welded complete all as specified and as directed by Engineer-in-Charge.

S&F Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete all as specified and as directed by Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) exc 0.50 sqm from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed by Engineer-in-Charge.

S&F sheet glass 3 mm thick ordianary quality and galzing with oil putty in square n.exc 0.5 Sqm in each pane complete all as specified and as direcetd at site.

S & F Galvanised mild steel wire cloth, 0.63 mm nominal dia of wire and average width of aperture 1.40 mm complete all as specificed and as directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete half fixed glazed and half top hung glazed complete all as specified and as directed (Glass shall be measured and paid separately).

S&F aluminium anodised barrel tower bolt 200mm long of extruded section with steel screws complete all as specified and as directed.

S&F aluminium anodised barrel tower bolt 150mm long of extruded section with steel screws complete all as specified and as directed.

S&F for aluminium handles size 150 mm cast type anodised complete all as specified and as directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt 12mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

Taking up or down GI tubing 15mm bore and connections including removal to store complete all as specified and as directed by Engineer in charge.

Taking up or down GI tubing 20mm bore and connections including removal to store complete all as specified and as directed by Engineer in charge.

S & F GI tubing 15mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer in charge.

S & F GI tubing 20mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer in charge.

Refixing 15mm and 20mm bore old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed.

S&F in repairs PVC connection 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F in repairs bib taps, cast copper alloy with butterfly handle, screwed for 15mm bore of iron pipe or for brass ferrule complete all as specified and as directed.

S & F in repairs stop valves cast copper alloy, screwed down, high pressure with butterfly handle, screwed both ends for iron pipe or for unions 15mm bore complete all as specified and as directed.

S&F in repair gun metal gate valve with iron wheel head, screwed both ends for iron pipes 20 mm bore complete all as specified and directed.

S&F 500 litres capacity (Triple layer) rotational moulded, polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings, including taking down existing old unserviceable water tank complete all as specified and as directed.

S&F Rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe- 290 (Gde E-165) complete all as specified and as directed.

S&F Rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe- 290 (Gde E-165) complete all as specified and as directed.

S&F in repairs Vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests including connection to trap and to flushing pipe, antisyphonage pipe complete all as specified and as directed.

S&F in repairs wash down water closet (pedestal pattern) complete (including fixing of seat cover) pedestal pan and trap including connection to drain (or outgoing pipe ) and flushing pipe, antisyphonage pipe etc complete all as specificed and as directed.

S&F in repairs PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc with and including PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S&F in repairs PVC (SWR) pipes, single socketed, 110mm bore in any length with rubber ring joints, fixed to walls etc complete all as specified and directed.

S&F in repairs PVC (SWR) pipes, 75 mm bore, single socketed, in any length with rubber ring joints, fixed to walls etc complete all as specified and directed.

S&F in repairs PVC (SWR) bends of any radius with access doors 110 mm bore/dia complete all as specified and as directed.

S&F in repairs PVC (SWR) bends of any radius with access doors 75 mm bore/dia complete all as specified and as directed.

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and as directed.

S & F in repair CP brass shower rose 125 mm dia complete all as specified and as directed.

M & L for 18-22mm thick machine cut cuddappah stone slab as in cooking platform (horizontal) or support to cooking platform (vertical) laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L Chitter black Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade over and including 20mm thick cement screed in CM (1:4) complete all as specified and as directed.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm with and including 32/40mm dia PVC waste pipe with coupling complete all as specified and as directed.

S&F in repair wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing complete all as specified and as directed.

S&F 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified and as directed.

Dismantling at any height of single layer Mangalore pattern or similar tiles in roof coverings complete all as specified and as directed.

S&F roof tiles, Mangalore Pattern, interlocking at side joints laid dry single layer or similar tiles in roof coverings complete all as directed.

Ditto all as per item 49 above but except tiles complete all as directed.

S&F ridge or hip tiles to suit Mangalore Pattern of roofing tiles bedded and jointed in CM 1:6 complete all as directed.

Ditto all as per item 51 above but except tiles complete all as directed.

S&F Galvanised, corrugated mild steel sheeting 0.63 mm thick with two corrugation side lap fixed with coach screws and washers and including necessary fittings as in roof or wall etc with grade of zinc coating 275, including dismantling of plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern as in roof covering/vally gutters.

M & L for plain, galvanised mild steel sheeting in ridges hips valley gutters drip and straight flashing (length and girth as fixed) by using 1.00mm thick sheet grade of zinc coating @275 Gms/Sqm both sides and welded or soldered joints including necessary fittings including dismantling of plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern as in roof covering/vally gutters complete all as specified and as directed by Engineer-in-Charge.

S&F second class soft wood clean sawn battens at 30 cm centre to centre and sectional area exceeding 15 and not exceeding 25 sqcm including Dismantling battens for tiles singles etc of any size including tilting fillets spaced exc 15 cm complete all as specified and as directed.

S&F 2nd class hard wood timber clean sawn fixed in scantling including dismantling timber fixed in scantlings 40 sqcm and over in section, in any position complete all as specified and as directed.

M&L 2nd class H/W plain fillets,rails, rafters, purlins, square, rectangular in section clean sawn secured with nails brads exc 13 sqcm but n exc 25 sqcm including dismantling timber as in fillets, rail, posts rafter, purlins etc under 40 sq.cm in section (unframed work) complete all as specified and as directed.

S & F for E-board 'Everest' make 595x595x4mm thick white prelaminated sett embossed reinforced designer ceiling board tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 4mm dia to be fixed by approved rawl plug, level and justers and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour including taking down wall/ceiling boards(fibre, pulp insulation etc) or insulation boards any thickness including fillets complete all as specified and as directed.

M&L Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with Creosote complete all as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surfaces etc at any position including raking out joints, hacking for key, scrubbing down with water complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finishing top surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finishing top surfaces even and smooth without using extra cement complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and as directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and as directed.

M&L preparing old plastered wall surfaces and applying two coats of oil bound distemper complete all as specified and as directed.

M & L preparing new plastered wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

M & L preparation of newly plastered surface of wall and applying two coat of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

M & L preparing old plastered wall surfaces and applying two coat of cement based paint (any tint) on walls complete all as specified and as directed.

M&L two coats of synthetic enamel paint over a coat of pink primer on new wooden surfaces including all necessary preparation over 10 cms width or girth complete all as specified and as directed.

M & L for preparing of old painted wooden surfaces of any description not otherwise described over 10cm width or girth and applyinbg one coat of synthetic enamel paint any tint complete all as specified and as directed.

M&L for preparing new Steel Surfaces of any description, over 10cm in width or girth, not otherwise described and applying evenly two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

M&L 25mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in base course including demolition of existing PCC floor complete all as specified and as directed.

M&L for non skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15 mm thick screed bed in CM (1:6) and demolition of existing floor tiles or stone slab complete all as specified and as directed.

M&L for non skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15 mm thick screed bed in CM (1:6) and demolition of existing floor tiles or stone slab complete all as specified and as directed.

M&L for non skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including 15 mm thick screed bed in CM (1:6) and demolition of existing floor tiles or stone slab complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles in vertical surface 450 X 300 X 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with and including 10 mm thick cement plaster (1:4) and Dismantling of floor hearth or wall tiling including cm bedding (but not backing) removing serviceable tiles in store rubbish of the premises as backing coat complete all as specificed and as directed.

Demolition of cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) complete all as specified and as directed.

M&L 75mm thick Plain Cement concrete (1:3:6) Type C-2 (using 40mm graded stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement complete all as as specified and as directed by Engr-in-Charge.

M&L 40mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) finishing the surface even and smooth with using extra cement complete all as specified and as directed.

M & L for point wiring with two single core PVC insulated multi stranded FRLSH Copper cable of size 1.5 sqmm drawn in and including PVC casing caping of required size with all fittings and accessories alongwith green colour FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one light/ fan / call bell point controlled by one, one way switch including PVC switch board and accesories of required size and making good to disturbed surfaces Note - One phase, one neutral and one earth of copper wire will measured as one point.

All as per item No 80 above for One three pin 5 Amp socket outlet point with cables 1.5 sqmm size on independent board.

All as per item no 80 above for One three pin 5 Amp socket outlet point ,with cables 1.5 sqmm size on same board.

All as per item no 80 above but FRLSH copper stranded cable of size 2.5 sq mm alongwith all fitting and accessories complete.

M & L for sub main wiring with two single core PVC insulated multi stranded FRLSH Copper conductor cable of size 6.0 sqmm drawn through in and including PVC casing caping of size with all accesories and one single core green colour FRLSH Copper conductor cable of size 4 sqmm as earth wire and connected to earth dolly and making good to disturbed surfaces .NOTE: (a)Two run of cable with one run of earth wire and one run of casing capping will be measured as one unit (RM)

S&F 5 Amp switch Piano flush type single pole one way incl dismantling taking down unsv one .

S&F 5 Amp flush type bell push single pole one way incl dismantling taking down unsv one .

S&F socket flush type 6 amps, 5 pin, 230v incl dismantling taking down unsv one all as specified and as directed.

S&F switch socket combination multipurpose 2-in-1 flush type 3 pin 16 amps and 3 pin 6 amps, 230v

S&F ceiling rose surface Bakelite three terminal all incl dismantling taking down unsv one

S&F flush type electronic fan regulator with 5 step type, 240 Volts AC, 50 Hz

S&F Sheet metal Enclosure SPN 8 way (MCB DB) Double door, 240 Volts AC of Make Schneider /ABB/Legrand or eqvt

S&F MCB, SPN (Double Pole) 32 amps, 240 Volts, 10 KA ‘’C” curve of Make Schneider / Legrand/ABB or eqvt

S&F MCB, Single Pole, 5 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’B” curve of MAKE- Schneider / Legrand/ABB or eqvt.

S&F LED Light fitting 1x18 watt AC decorative box type with driver ,holder including LED Tube Light connecting with three core flexible copper conductor cable from ceiling rose complete. Make-CG/ Bajaj/Philips/HPL/Havells

S&F LED Light fitting mirror type with with high output diffuser 2 feetr , 10 watt incl driver and Lamp connecting with three core copper conductor cable complete. Make-CG/ Bajaj/Philips/HPL/Havells

S&F LED building security light 15 watt, 230V complete with all accessories and including connecting up to ceiling rose with 0.5 sqmm three core copper flexible conductor cable, One GI medium grade 20mm dia bracket of total length 50 cm and fixed to wall with 2 Nos MS Clamp and fastener all as specified and directed. Make-HPL, Cat Part No HPLLEDST1560N or equivalent in Philips/Bajaj/CG

S&F ceiling fan of 1200 mm sweep 230 volt and min air delivery 210 CFM incl fan rod with suitable clamp, nut, bolt & washers complete of make Havells/Usha /Bajaj or equivalent all as specified and directed.

S&F Exhaust fan Metal body light duty 300 / 225 mm sweep 230 volt AC complete with frame and Louvers of Make- Havells/Almonard/ Crompton Greves or eqvt.

Making of suitable hole in brick / stone wall for fixing of Exhust Fan 300 / 225 mm sweep complete all as directed by Engineer-in-charge.

M & L for Earthing complete with galvanised steel pipe electrode, 40 mm bore, medium grade, 3 mtr long buried directly and vertically in ground with top edge at ground level after making bore hole of size not less than 300 mm dia and 3.0 Mtr long using suitable mechanical drilling rig (for drilling near the specified bldg), connected with galvanised steel earthing lead of 4mm dia all as shown in Plate No-2, connected to the earthing test point, concrete pit in PCC 1:3:6 type C-2with RCC precast pit cover slab 400mmx400mmx80mm with handle for lifting made out of 8mm dia MS rod, funnel, wiremesh, 15 mm dia light grade GI tubing for protection of GI wire 4mm dia, charcoal and salt in alternate 150mm thick layers around GI earth pipe, including necessary returning filling in & removal all as specified or indicated in SSR Part-I, including testing to achieve earth resistance value as per IS specification on completion.

Supply and lay LT UG cable 3.5 core 50 sqmm XLPE insulated sheathed armoured heavy duty 1100 volts grade laid in trenches complete incl indoor/ out door joint all as directed and specified.

Supply and lay LT UG cable 3.5 core 70 sqmm XLPE insulated sheathed armoured 1100 volts grade laid in trenches complete incl indoor/ out door joint all as directed and specified.

Excavation in trenches for laying of cable , for pole & stay N. exc.1.5 mtr wide & n.exc. 1.5 mtr in depth & getting out in Hard/dense Soil complete all as as specified and as directed by Engr-in-Charge.

Returning & refilling in including spreading levelling watering & well ramming in layers n.exc. 25 cm thick in soil complete all as as specified and as directed by Engr-in-Charge.

Removal of excavated material n. exc. 50 m and deposited where directed at a leveln. exc 1.5 m above the starting point complete all as as specified and as directed by Engr-in-Charge.

Material and labour for dry sand cushioning to underground cables in trenches including spreading, levelling, hand punning and consolidating, complete all as specified and directed.

M & L for reinforced precast concrete cable cover class LV type -1 flat of size 250mm x 150mm x 40 mm for cable protection all as specified and directed by Engr-in-Charge.

M&L for GI Pipe 100 mm dia medium grade laying in trenches for cable protection complete all as as specified and as directed by Engr-in-Charge.

Cutting to the existing Road/hard standing of any description and make good as per existing pattern complete all as directed by Engineer -in-charge.

Design, fabricate ,supply ,testing and commisioning of CPRI approved factory made LT Panel Board out door type fabricated out of 2mm thick CRCA sheet steel for outer body and 2.00mm thick CRCA Sheet for inner partition walls, independent cabinate with cabinate doors for MCCBs, Bus Bars, cable trays, metering equipment, vertical wall mounted type (With Bolts and Nuts) of size 1.4x1.6x300 mm with front door having glass window for viewing KWH Meter and other doors shall be opque.All doors should have gasket and locking arrangements. The cabinet shall be powder coated internally and externally, minimum IP-54 protection, suitablily grouted to PCC complete with internal wiring, epoxy powder coated and connection of cable ends with suitable size of aluminium cable lugs with the following accessories. (a) INCOMING (i) MCCB 100 Amps, 4 Pole, 415 V, 25 KA, -01 Nos (ii) Aluminium bus bar of cross section 40x5 mm duly mounted on FRP/DMC insulators suitable for 1.5 times of rating current and necessary drilling for connection and duly covered with heat shrinkable PVC sleeves of standred colour code -04 nos. (iii) Single phase KWH meter of rating 5-30 amps paid and measure saparetely (iv) MCB SPN 25 Amps, , 10 KA, Legrand Cat No 408716 Legrand/Havells/schiender.-12 Nos (v) Two way backelite with connector with nuts and volts and washers suitable for connecting the outgoining wires in the cabinet.. Make HPL/L&T/SIEMEN-9 Nos. (vi) Internal wiring of meter /MCB/ cable connector shall be carried out with 10 sq mm multicore flexible copper wire with FRLSH Grade PVC insulation of 1100 volts rating including necessary lugs/bolts/nuts/washers etc.Make of cable Havells/Polycab/Finolex. (vii) Indicating LED lamp(RYB) suiatble for AC 230 volts single phase supply-03 sets. Make RAAS/SIEMENS/L&T.

M & L for Single phase KWH meter of rating 5-30 amps base mounting electronic temper proof type with optical port suitable for AC 230 volts, 50HZ supply. Make HPL/L&T/SIEMEN

Om Construction

M/S JAYCONSTRUCTION CO