Providing Deep Borewell with Sintex Tank in ward 35

Amount

Towards cost of Geophysical investigation survey charges.

Supply and delivery of 200mm dia of (Casing medium) PVC casing plain pipe including cost and conveyance at site etc., complete as per standard specification (Twad S no 1.1 pg.no 22)

Supply and delivery of 150mm dia of (Casing medium) PVC casing Slotted pipe ( Company Slots) including cost and conveyance at site etc., complete as per standard specification ISI make (Twad S no 1.1 pg.no 22)

Supply and delivery of 150mm dia of (Casing medium) PVC casing plain pipe including cost and conveyance at site etc., complete as per standard specification `(Twad S no 1.1 pg.no 22)

Drilling 150mm dia pilot bore to the required depth Below ground level.(Twad S no 12 pg.no 302)

Drilling 150mm dia pilot bore up to 60 m to 90 m from Ground level.(Twad S no 12 pg.no 302)

Drilling 150mm dia pilot bore up to 90 m to 120 m from Ground level.(Twad S no 12 pg.no 302)

Drilling 150mm dia pilot bore up to 120m to 150 m from Ground level.(Twad S no 12 pg.no 302)

Drilling 150mm dia pilot bore up to 150m to 180 m from Ground level.(Twad S no 12 pg.no 302)

Supply and delivery of 200mm dia(8”) PVC end cap including cost and conveyance etc., complete (Twad Sor 1.5 pg.no 27)

Reaming from 150mm dia pilot bore to 200mm dia size bore as directed by the Departmental Officer, to the required depth up to 60 from Ground level (Twad Sor 12.b pg.no 302)

Labor charges for inserting the P.V.C. casing pipes assembly with slots (or) without slots in the drilled holes including joining the pipes etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Municipal Engineer excluding cost of casing pipe etc., complete 200mm dia PVC casing pipe (Twad Sor 12.e pg.no 304)

Charges for developing the bore wells with Air Compressor 600cfm (Minimum 8 hours) including transportation labor and fuel charges for Compressor as directed by the Departmental Officer and conducting yield test by “V” notch method.(Twad Sor b pg.no 305)

Supply and Fixing of 5 HP Motor Submersible Pump set ISI mark IS 8034Without panel board 75LPM and 60M Head including Fixing Charges and all Charges etc. Complete.(Rate with TNVAT @4% on Basic cost Excise Duty)(Sor S no 408 pg.no 105)

Supply and delivery of suitable 3 phase panel board to 5HP with DOL Starter Auto On/Off Switch etc.,(Twad Sor S no 112 pg.no 115)

Supply and Delivery of 2.5 Sqmm PVC insulated and Sheathed 3 Core flat type copper cable confirming to IS 694/1990 Including all charges with excise duty and handling charges etc (Twad Sor S no 12.1 pg.no 120)

Towards Labour Charges for the errection of Submersible pump set in bore well including fixing and jointing submersible cable with proper clamps up to the starter to riser pipes to the required depth valves erection clamps, pressure gauge up to the exterior of panel board consisting of TPICN switches starter ,Volt meter, Ammeter, three pilot (indicating) Lamps capacitor single Phasing preventor,water level guard and laying and jointing the cables and twin earthing as per IE rules etc., Complete and testing the pump set and trail run for 10 days 2 HP Plat form All round (Twad Sor S no 17.3 pg.no 308)

Supply and run off 4 to 6 Sq.mm polythene insulator and PVC sheathed (Heavy Duty) service meter Aluminium cable of 1100 V grade on bearer wire for servive connection mains (SD 61).(320 Aluminim Wire)(Twad Sor S no 12.0 pg.no 120)

2" dia Pipe clamp set (Twad s no 5.16 pg no 44)

2" dia pvc bend (Sor s no 395 c pg no 100)

2" dia G.I Elbow (Twad s no 5.16 pg no 44)

2" dia G.I Union (Twad s no 5.16 pg no 44)

2" dia gate valve (Twad s no 5.2 pg no 45)

2" U Pvc Pipe (Twad s.no3(6) pg no 24)

2" dia pvc pipe (Sor s no 394 pg no 99)

2" dia pvc Tee (Sor s no 395d pg no 100)

3/4" dia G.I Tee (Twad s no 5.2 5.16 pg no 44)

3/4" dia G.I Elbow (Twad s no 5.2 5.16 pg no 44)

3/4" dia Pvc Tap (Sor s no 160 pg no 68)

3/4" dia GI Coupler (Twad s no 5.2 5.16 pg no 44)

saddle piece (Twad s no 5.1 B 5.16 pg no 44)

Supply and delivery and fixing of HDPE tank 2000 litres capacity as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixnig charges as directed by TWAD Board officers etc.,(Twad S no 17.0 p no 89)

Providing Construction of Brick work for HDPE tank with Pcc in 1:2:4 and Brick work CM:15 using II class ground moulded bricks of size 8 3/4 x 4/2 x 3/4 Earth Filling Plastering CM 1:5 20mm Thick painting etc Complete

Supply and fixing of 0.75 x 0.75 x 0.45 size made up with MS angle and plats of a kiosk erected on a masonary pedsal for protecting accessories etc., complete complying with standard specification.(Twad s no 18.0 pg no 89)

Providing painting and lettering over the PVC tank for the work details as per instrution given by the departmental officers etc., complete complying with standard specification.

Electrification charges for EB service connection

Supply and delivery of 25mm GI Pipe Service Pipe With Bend Including Coat and Coneyance etc,Complete as per Standard Specification as Directed by the Departmental Officers (Twad S no 50 Pg no 42

Sri Vaishnavi Enterprises