SPL REPAIR TO BLDG NO. P-46 AND P-47 (OR MD ACCN DEFENCE COLONY) UNDER ZONE-II AREA AT JAIPUR MIL STN

Taking down cement plaster or cement lime plaster, any description on brick, stone walls or concrete surface of ceiling etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified & as directed.

Demolition of cement concrete (unreinforced) in any description and in any position, not otherwise specifically provided for and removal of same from outside MOD land complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and removal of same from outside MOD land complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:4 on fair faces of brick masonry surfaces or concrete surface finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm thick in CM 1:6 on stone masonry surfaces or on surface other than fair faces of brick masonary finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm thick in CM 1:4 on stone masonry surfaces or on surface other than fair faces of brick masonary finished even and fair complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on concrete surface of ceiling finished even and smooth w/o using extra cement complete all as specified and directed.

M & L for dubbing out average 5mm thick on irregular faces of ceiling in CM (1:3) as floating/ setting coat in patches n exc 3 sqm each patch complete all as specified and directed .

M&L for coloured jointfree non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed using chemical adhessive of exterior grade of 5-7mm thickness and pointed in white or coloured cement to match the shade of tile complete all as specified and directed Note : Quoted rate shall be inclusive chemical adhesive

M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm, in floors etc. set and jointed using chemical adhessive of exterior grade of 5-7mm thickness and pointed in white or coloured cement to match the shade of tile complete all as specified and directed Note : Quoted rate shall be inclusive chemical adhesive

M&L for light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles exc 0.18 sqm but not exceeding 0.38 Sqm on vertical surfaces of wall such as dado, skirting etc set and jointed using chemical adhessive of exterior grade of 5-7mm thickness and pointed in white or coloured cement to match the shade of tile complete all as specified and directed Note : Quoted rate shall be inclusive chemical adhesive

M&L for coloured glazed ceramic tiles 450mm X 300mm X 7 to 8mm thick on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed

M & L for 20 mm thick Granite (Rajasthan black) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat forms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over 15mm thick screed bed in CM 1:4 complete all as specified and directed

M&L 18-20 mm thick kesaria Green marble (table rubbed & polished) as in steps, jambs, pillars, window cills, cooking platforms and like in CM 1:4 incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed.

M&L for 25mm thick marble slab (machined polished) as in vertical partitions, below kitchen cooking plat form and raised platform of kitchen complete all as specified and directed .

M&L for 25mm thick PCC 1:2:4, type B-1 (using 20mm graded stone aggregate) as in flooring and all other similar works finished even and fair complete all as specified and directed.

M&L 15 mm thick screed bed or bedding layer in cement mortar 1:6, for laying floor finishes /tiles /kota stone etc complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick of size 550 x 550 mm in floor over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and granite polishing complete all as specified and directed .

M & L machine cut kota stone slab flooring 20-25mm thick in steps in single piece laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed.

M & L machine cut kota stone slab flooring 20-25mm thick in riser of steps, dado, skirting in single piece laid over and including 10mm thick bedding layer in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed.

Rounding to edges of stones slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

S&F Factory made single plain WPC (Wood Polymer Composite) solid plain shutter, cabinets etc of 18mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant WPC to be laminated with acrylic sheet foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on one faces and other face pasted with white sunmica sheet of minimum 14 micron thick in shutter and including fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S&F Factory made single plain WPC (Wood Polymer Composite) solid plain shutter, cabinets etc of 12mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant WPC to be laminated with acrylic sheet foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on one faces and other face pasted with white sunmica sheet of minimum 14 micron thick in shutter and including fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S & F smart slide stainless steel (Grade SS-304) kitchen Plain basket, fancy type of size 17" x 20" x 4" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) kitchen prerforated cutlery basket, fancy type of size 17" x 20" x 4" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) kitchen cup & saucer basket, fancy type of size 17" x 20" x 4" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) Plate/thali basket, fancy type of size 17" x 20" x 6" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F smart slide stainless steel (Grade SS-304) kitchen grain baskets, fancy type of size 17" x 20" x 10" of approved make for modular kitchen complete all as specified & directed Make : Godrej, Hindware, Lifetime or equivalent

S & F stainless steel (Grade SS-304) telescopic basket guide/sliding channels suitable for running basket, bright finish complete all as specified & directed. Make : Godrej, Hindware, Lifetime, Hettich or equivalent

S & F auto close hinges, stainless steel of grade SS-304 , bright finish fixed complete all as specified. Make : Godrej, Hindware, Lifetime or equivalent

S & F stainless steel handles of size 100 mm fancy type of approved make complete all as specified & directed. Make : Godrej, Hindware, Lifetime or equivalent

S&F in repair sinks made of stainless steel 18 guage of grade SS-304, kitchen or labortory with plugs, washers and wastes pipe and coupling including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to ipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair 15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or laid in floor including taking down old complete all as specified and directed.

S&F in repair 20 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or laid in floor including taking down old complete all as specified and directed.

S&F in repairs 15 mm bore bib tap, fancy type, chromium plated cast copper alloy with cruth or butter fly handle, long body, screwed down, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

S&F in repair 15mm bore swan neck kitchen sink cock, cast coper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union for kitchen complete all as specified and directed.

Supply only pillar taps 15mm bore swan neck cast coper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union complete all as specified and directed.

S&F in repair brass CP towel rail 20mm dia, D type 60 cm long between flanges complete all as specified and directed.

S&F in repair double soap dish, CP brass 'R' type fixed to plugs with chromium plated brass screws complete all as specified and directed..

S&F in repair brass chromium plated shower rose 125mm x 125 mm size with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair 15mm bore stop/angle valves, cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed for iron pipes or for unions and fixed complete all as specified and directed.

S&F in repair PVC Connections 15mm size, 450mm long with PTMT nuts complete all as specified and as directed.

S&F in repair 20mm bore gun metal gate valve, screwed down high pressure with iron wheel head screwed both ends for iron pipe or for union complete all as specified and directed.

S & F in repair 15mm bore wall mixer, brass, chromium plated, fancy type, 3-in-1 for mixing hot & cold water, with L-bend pipe for connection to overhead shower, bright finish with three joints screwed the ends for iron pipe and plugging complete all as specified and directed.

S & F in repair 250 mm corner glass shelf with brass brackets incl chromium plated brass screws complete all as specified & directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), including plastic water closet seat, black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device and connection to drain (or out going pipe) and to flushing pipe etc. incl trap set in cement concrete complete all as specified and directed.

S&F in repairs PVC valveless, syphonic action type flushing cistern, low level, 10 ltr capacity, white, with intel, ball valve, float and handle including brakects, 32 mm dia polyethylene of low or high density or PVC flushing pipe and connections to pipes and fixing of chain and pull, or lever, if any complete all as specified & as directed.

S&F in repairs vitreous china wash hand basin white flat back of size 550 x 400 mm excluding taps, waste pipe, chain & plug and porcelene stopper but including brackets /fastners, 32mm dia brass chromium plated waste coupling with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, cutting for and pinning in ends of brackets, including fixing of pillar tap complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work with sub-class 'B' bricks (old size), straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed

M&L for brickwork with subclass ‘B’ bricks (old size), straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 complete all as specified and directed.

M&L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed.

Dismantling of 75mm bore cast iron soil/waste pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed. Note : The length shall be measured along the centre line including fittings and accessories

Dismantling of 100mm bore cast iron soil/ waste pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed. Note : The length shall be measured along the centre line including fittings and accessories

S&F 110 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified & directed.

S&F 110 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints fixed to wallls complete all as specified & directed.

S&F 75 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints laid in trenches or floors complete all as specified & directed.

S&F 75 mm bore UPVC (SWR) drainage pipes (type B conforming to IS-13592) single socketed in any length with rubber ring joints fixed to wallls complete all as specified & directed.

S&F 110 mm dia PVC (SWR) junction single (Single Tee with access door) equal or unequal complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends any radius with access door complete all as specified and directed.

S&F 75mm dia PVC (SWR) junction single (Single Tee with access door) equal or unequal complete all as specified and directed.

S&F 75mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F 75mm dia PVC (SWR) branch piece, double (double y) complete all as specified and directed.

S&F 110 mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair PVC (SWR) 75 mm dia of outlet nahani trap/floor trap including jointing with solvent cement complete all as specified and directed.

S&F in repair SGSW gully trap square or round mouthed type 'P' of size 150mm x 150mm with CI grating complete all as specified and as directed

S & F in repair MS CP Grating doom 100 mm dia with or without waste hole complete all as specified and directed.

S & F in repair 500 Ltrs capacity rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc incl 20mm dia ball valve high pressure of PTMT with polythene flynut and aluminium rod incl dismantling of old tank all as specified in SSR Part I complete all as specified and directed by Engineer-in-Charge.

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed.

S & F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube of 1.25 mm thickness suppling & fixing in opening as per specification & drawing given in SSR Part-I complete as directed and specified

S&F Factory made moulded solid core PVC door shutter decorative both side 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing given in SSR Part-I complete as directed and specified.

S&F 30 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, 1mm thick veneer / mica of approved pattern on both side and teak wood on edges complete all as specified and as directed

S & F 35mm thick second class hardwood factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc divided into square , with plain, chamfered or rounded, mitred and rebated sash bars any numbers , fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :- S & F Glass/gauge shall be measured and paid for separately

S & F 30mm thick factory made partly gauzed and partly panelled skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :- S & F Glass/gauge shall be measured and paid for separately

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples in window or door complete all as specified and as directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples in window or door complete all as specified and as directed.

S&F aluminium mesh of weight exc.0.55 Kg/Sqm as support to SS wire cloth complete all as specified and directed.

S&F mild steel framed work such as door frame, grills, gratings, etc. with ends of bars shouldered and / or riveted or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways;drainage crossings, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed

S & F 100 mm butt hinges medium weight cold rolled mild steel and fixed complete all as specified and as directed.

S & F 250mm long stainless steel sliding door bolt, bolt type, not less than 12mm dia with & including a min of six bolt & nut, four on bolt plate & two on staple plate and fixed complete as directed and specified.

S & F stainless steel handles of size 150 mm fancy type of approved make and fixed complete all as specified & directed.

S & F 200mm long stainless steel (Grade SS-304) barrel tower bolts and fixed complete all as specified & as directed.

S & F 75mm (overall size of cover plate) size floor door stoper of stainless steel body and tongue, anodised, with double pin and rubber shoe fixed in bottom of door shutter complete all as specified and as directed.

S & F MS Helical door spring 150mm long including roller and roller plate complete fixed to angle iron chowkats. as directed and specified.

S & F in repair pressed steel factory made cupboard shutter with frame of 1.25 mm thick and shutter 1 mm thick PBI sheet with 6 nos 3.15 mm thick and 100 mm long steel hinges, godrej patern locking arrangement incl 12 mm dia vertical rod incl spray painting in factory in wood finish pattern complete all as specified and directed

S&F in repair 20 mm dia SS (grade 304) drapery/curtain rod medium weight incl taking down old one with finials, brackets etc complete all as specified and directed

S&F SS (grade-304)brackets/ end brackets for holding 20mm dia drapery rod complete all as specified and as directed.

S&F SS (grade-304) Finials, fancy type of approved make and pattern suitable for 20mm drapery rod complete all as specified and directed.

M&L for prearation of new or previously untreated steel and iron surface of any description, over 10cm in width and girth not otherwise described and applying two coat of synthetic enamel paint over one coat of red oxide (zinc chrome) primer complete all as specified and directed.

M&L preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified & as directed.

M&L for preparation of new wooden or wood based surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of old painted surfaces of wood or wood based materials of any description ot otherwise described, over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for WPT in sunken floors as described here under:- Sunken floor and sides up to finished floor level shall be plastered with 15 mm thick cement plaster in CM 1:4 mixed with water proofing liquid @ 150 ml per bag of cement . (ii) Pitch free polyurethane elastomeric single compound liquid membrane with UV restence approx thickness of layer (1-2mm)(in two coat of 600 micron each ) with coverage of 0.94 kg per Sqm in each coat complete all as specified and directed by Engineer-in-charge with following specification (i) Elongation 400%ASTMB-412 (ii) Tensile strength-2.10 Mpa ASTMD-412 (iii) Crack bridging at low temp-1.5mm ASTMC-836 including preparation of surface and filling cement concrete 1:4:8 type D2 (40mm graded aggregate) ,including demolition existing sunken treatment complete all as specified an as directed Note :- (i) liquid membrane water proofing membrane shall be laid in sunken floor and on sides up to finished floor level. (ii) The waterproofing treatment shall be got carried out by the manufacturer or their authorised applicators. (iii) Above aspects are deemed to be included in quoted rate. Note : Floor area only will be measured for payment purpose.

M&L for preparing newly plastered surfaces and applying two coats of distemper with distemper oil emulsion white or tinted over a coat of primer over two coat of wall care putty to make smooth the undulated surfaces complete all as specified and directed.

M&L for complete removal of existing treatment on walls, including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of distemper with distemper oil emulsion white or tinted by mechanical means over a coat of primer over two coat of wall care putty to make smooth the undulated surfaces complete all as specified and directed.

M&Lfor Preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer with hand roller complete all as specified.

M&L for complete removal of exiting surface & thourughly wetted surface to ensure better sticking including sand paper gentle rubbing to obtain smmoth surfaces, including all necessary arrangement for execution of work and applying two coats of Cement Base Paint using hand roller of over one coat of water based white pigmented akali resistant priming paint for external wall complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of old decorated plastered surfaces of walls, soffits of chajjas, cornices etc and applying two coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for complete removal of existing treatment old plastered or unplastered decorated surfaces of ceiling and applying two coat of white wash complete all as specified and directed.

M&L providing cement concrete type B-1, 1:2:4 (using 20 mm graded aggregate) in lintels up to 1.5m clear span, cills, bed plates,coping, kerbs water trough & the like including weathering, slightly rounded or chamfered angles & throating complete as specified and directed

Taking down existing roof treatment complete including demolition of PCC, Mud phuskas, lime concrete etc any description upto mother slab, and properly cleaning the surface to remove loose particles with wire brushes and removing the debris out side of MoD land complete all as specified and as directed.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC type B-0,( 1.2.4) using 12.5 mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement measured & paid separately.

Supply only integral water proofing compound ISI marked complete all as specified and directed.

M&L rendering 10mm thick in cement mortar (1:3) on concrete surfaces to receive water proofing treatment finished even and fair complete all as specified.

The surface shall be painted with one coat of polymeric primer @ 0.40 kg per sqm conforming to IS: 3384 and a coat of bitumen grade 30/40 @ 1.20 kg/ Sqm below the layer of APP based polymeric memberance.( 3 mm thick minimum weight not less 150 gms ) and Side over lap shall be 75 mm and ends shall be 100 mm and all over lap and joints insert upto the ht 150 cm vertical surface imbeded in wall and finishing in CM 1:3, embeding membrane into spout pipe, roof down ward facia and shall sealed by torch application with bitumen 30/40 grade, coved filled in PCC (1:2:4) type B-0 of radious 75 mm at roof junction, parapet wall and other vertical surface as per manufacturers instruction complete all as specified and directed. Note : work shall be executed through authorised applicator of manufacturers only

M&L preparation of APP based polymeric surface and applying two coat of aluminium paint all as specified & as directed.

M & L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

M&L for 75mm thick plain cement concrete 1:4:8, type D-2 using 40mm graded stone aggregate as in sub base to flooring complete all as specified and directed.

M&L sand filling under floors or in foundations including watering, spreading and levelling in layers of 25 mm thick complete all as specified and as directed.

M & L rubber moulded machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, with grey cement and no pigment laid over 25mm thick sand cushion layer complete all as specified and as directed. Note : Sand cushion shall be measured and paid seperately

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

S & F in repair stainless steel kitchen plate rack of approved quality of overall minimum size 750 x 600 x 250mm with partitions for small/ large plates etc made out of stainless steel 24 gauge, fixed with rawl plug and CP steel screws complete all as specified and directed.

Dismantling/ chipping of unsound weak loose & cracked concrete/ cover of reinforcement over RCC columns / beam / parapet, roughening and cleaning concrete surfaces with steel wire brushes, washed with water and allowed to dry, including dusting of steel reinforcement, mild steel wire fabric of weight exc. 4 Kg/ Sqm as reinforcement, tied or tuck welding to existing reinforcement to concrete surfaces, applying adhesive/admixture over steel mesh, applying rust remover, removing rusted steel bars, applying two coats of alkaline rust converting primer SIKA rust off - 100 or equivalent apply bonding agent to old concrete surface and providing PPM to the reqd thickness and finishing the surface with micr concrete SikaREp Microcrete-4 or equivalent having compressive strength more than 60 N/mm2 ( 28 days) to true line incl necessary formwork, shuttering, scaffholding etc reqd at site of work complete all as specified and directed.

Dismantling loose/cracked concrete completely as in chajjas, balconies, roof projections upto double storey buildgs including cleaning existing reinforcement, applying rust remover, removing rusted steel bars, apply bonding agent to hold concrete surface and casting chajjas using RCC 1: 1 1/2: 3 type B1 (using 20 mm graded stone aggregate) to outward slope incl necessary formwork, scaffholding etc complete all as specified and directed.

Dismantling/ chipping of unsound weak/ loose & cracked concrete/ cement plaster as in soffits of chajjas, ceillings, roof projections upto double storey buildgs including cleaning existing reinforcement, applying approved rust remover, removing rusted steel bars if necessary , apply Epoxy resin concrete bonding (Sikadur-32LP @ 0.4 Kg/Sqm) coat on prepared RCC surfaces as per manufacturers instructionbonding agent to old concrete/ plaster surface and finishing to required thickness with PMR (polymer modified ready to use cementitious mortar) complete all as specified and directed.

M&L Mild steel TMT bar 10 mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as directed and specified.

,--- ditto--- all as per srl item No. 121 above but TMT bar of 6 to 8mm dia complete all as directed and specified.

Dismantling loose / cracked concrete cover as in RCC facia upward or downward of thickness not exc 100 mm , cleaning concrete surfaces with steel wire brushes, washed with water and allowed to dry incl cleaning of rusting of steel reinforcement, providing mild steel wire fabric of weight exc. 4 Kg/ Sqm as reinforcement tied to existing reinforcement or tuck welding to existing reinforcemrnt and applying PMR (polymer modified ready to use cementitious mortar) to the reqd thickness and finishing the surface to true line incl necessary formwork shuttering, scaffholding etc reqd at site of work complete all as specified and directed

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates conforming to Fe410-W(Gde E-250) Quilaty B complete all as specified and directed.

M&L pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws /J hook, L-type crancked hook complete all as specified and directed

M&L for retrieving peeple plants from walls roofs, chajja upto double storey height incl taking out deep roots and poring Hcl acid and making good the disturbed surfaces with CM 1:4 incl all means reqd at site complete all as specified and directed.

Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, n exc 200mm thick (Horizontal or sloping) for fair finished flat surfaces of concrete complete all as specified and directed.

M & L for RCC M-25 (Design Mix) (using 20mm graded stone aggregate) as in slab supported on walls , beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed. Note : Reinforcement & formwork shall be measured and paid for separately.

S & F repair for Toilet Duct Pipelines for Domestic Water Pipes downtake pipes fixing done with Pipe Supporting Clamping System having Profile Bracket + Slotted C Channel + U Bolt R/M System - 1. Domestic Water Supply Down take lines 3/4" GI - 2 nos. from Terrace to 1st Floor Vertical Fixed line with wall distance 2": Pipe Support Clamping made of 1. Profile Bracket Wall Distance 2" made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Slotted "C" Channel B3 Type to be used of size 12" (Continuous Slotted "C" Channel with ribs) made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing as per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty.: 1. Profile Bracket Wall distance 2" - 2 Nos. 2. Continuous Slotted C Channel of B3 Type Size 12" - 1 No.; 3. U Bolt R/M for 3/4" GI pipe Dia. - 2 nos. 4. Justi Khilla GI coated 2 1/2" - 4 nos. Refer CE Jaipur Zone Technical Drawing no. TD/2022/01.

S & F repair for Toilet Duct Pipelines for Domestic Water Pipes downtake pipes fixing done with Pipe Supporting Clamping System having Mono Bracket + U Bolt R/M System - 1. Domestic Water Supply Down take lines 3/4" GI - 1 nos. from 1st Floor to Ground Floor Vertical Fixed line with wall distance 2": Pipe Support Clamping made of 1. Mono Bracket with slot Wall Distance 2" for 3/4" GI pipe made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs. 2. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing as per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty.: 1. Mono Bracket with Slot Wall distance 2" for 3/4" GI pipe - 1 Nos. 2. U Bolt R/M for 3/4" GI pipe Dia. - 1 nos. 3. Justi Khilla GI coated 2 1/2" - 2 nos. Refer CE Jaipur Zone Technical Drawing no. TD/2022/01.

S & F repair of Toilet Duct Pipelines for Soil Water Down take pipe fixing done with Pipe Supporting Clamping System having Mono Bracket + U Bolt System - 1. Soil Water Pipe 4" PVC - 2 pipe running from Terrace to Ground Floor Vertical Fixed line with wall distance 3": Pipe Support Clamping made of 1. Mono Bracket with Slot Wall Distance 3" for 4" PVC pipe made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079); material size 48 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs. 2. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing as per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty.: 1. Mono Bracket with Slot Wall distance 3" for 4" PVC pipe - 1 Nos. 2. U Bolt R/M for 4" PVC Pipe Dia. - 1 Nos. and 3. Justi Khilla GI coated 2 1/2" - 2 nos. Refer CE Jaipur Zone Technical Drawing no. TD/2022/01.

S & F repair for Bathroom Duct Pipelines for Domestic Water Pipes downtake pipes fixing done with Pipe Supporting Clamping System having Profile Bracket + Slotted C Channel + U Bolt R/M System - 1. Domestic Water Supply Down take lines 1/2" GI - 2 nos. from Terrace to 1st Ground Floor Vertical Fixed line with wall distance 2": Pipe Support Clamping made of 1. Profile Bracket Wall Distance 2" made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Slotted "C" Channel B3 Type to be used of size 12" (Continuous Slotted "C" Channel with ribs) made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing as per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty.: 1. Profile Bracket Wall distance 2" - 2 Nos. 2. Continuous Slotted C Channel of B3 Type Size 12" - 1 No.; 3. U Bolt R/M for 1/2" GI pipe Dia. - 2 nos. 4. Justi Khilla GI coated 2 1/2" - 4 nos. Refer CE Jaipur Zone Technical Drawing no. TD/2022/01.

S & F repair for Bathroom Duct Pipelines for Waste Water Pipe downtake pipes fixing done with Pipe Supporting Clamping System having Profile Bracket + Slotted C Channel + U Bolt R/M System - 1. Waste Water Pipe 4" PVC Down take running from 1st Floor to Ground Floor Vertical Fixed line with wall distance 3": Pipe Support Clamping made of 1. Profile Bracket Wall Distance 3" made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. 2. Slotted "C" Channel B3 Type to be used of size 10" (Continuous Slotted "C" Channel with ribs) made of Low Carbon Hot Roll gauge corrected Oil Pickeled & Drawn (HROP D) Steel (IS 1079) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. 3. U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing as per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 10204 3.1. Material Qty.: 1. Profile Bracket Wall distance 3" - 2 Nos. 2. Continuous Slotted C Channel of B3 Type Size 10" - 1 No.; 3. U Bolt R/M for 4" PVC Pipe Dia. - 1 nos. and 4. Justi Khilla GI coated 2 1/2" - 4 nos. . Refer CE Jaipur Zone Technical Drawing no. TD/2022/01.

S&F factory made UPVC top hung double shutter using standard sections as per manufacturers instructions incl SS wire guage of 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and glazed shutter with 5 mm thick toughned glasss incl hinges stays & hardware etc complete9.Design of ventilator shall be - bottom half fixed toughened glass 5 mm th , upper half with two shutters ie gauged and glazed.) filling the gap between wall & UPVC frame with silicon sealant complete all as specified & directed. ( Note: The unit rate quoted by contractor excluded cost of glass and includes all other connected accessoried & silicon sealant for fill the gap between wall and window, net opening will be measured for payment purpose)

S & F for 5mm thick Toughned glass as in hinged door/window/ventilator ,partitions automatic doors and similar work including cutting to shape,drilling holes required.

S&f for 4.8 mm thick frosted glass odinary qulity and glazing with neosprene beading n.exc 0.5 Sqm in each pane complete all as specified and as directed.

Taking down carefully surface aluminum /copper point wiring, casing capping /PVC concealed conduit for (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable, single core, 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one light point controlled by one, one way switch 6 Amp complete all as specified and directed.

,---ditto--- all as per item No. 140 above but for one fan point controlled by one switch 6 amp complete all as specified and directed.

,---ditto--- all as per item No. 140 above but for one 3 pin 5 Amp socket outlet controlled by one switch on same board complete all as specified and directed.

,---ditto--- all as per item No. 140 above but for one 3 pin 5 Amp socket outlet controlled by one switch on indepdendent board complete all as specified and directed.

,---ditto--- all as per item No. 140 above but for one bell point controlled by one bell push complete all as specified and directed.

,---ditto--- all as per item No. 140 above but for one light point controlled by two, two way switch complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable single core, 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor incl modular sunken GI metal boxes not less than 1.0mm thick moulding in wall and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc as required for one 3 pin, 15amp socket outlet on independent board complete all as specified and directed.

Taking down carefully sub main wiring with PVC casing capping / PVC surface conduit and making good disturbed surfaces complete all as specified and directed.

M&L for sub main wiring with two run of 4 Sqmm single core, PVC insulated, unsheathed, FRLS multistranded copper conductor cable alongwith one run of 4 Sqmm earth wire as earth continuity conductor (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed rigid non-metallic PVC conduit of 20mm dia, ISI marked, ivory colour with fitting / fixing accessories of suitable size as required including making connection as required complete all as specified and directed. NOTE - Two run of 4 sq.mm phase and neutral wire, One run of 4 sq.mm earth wire & One run of PVC conduit with accessories shall be measured as One length.

,---ditto-- all as per item No. 148 above but wiring with two run of 2.5 Sqmm and one run of 2.5 Sqmm earth in 20mm dia PVC conduit complete all as specified and directed.

S&F modular socket, 6 Amps, 2/3 pin combined, 2 module AC 240 volts complete all as specified and directed.

S&F modular switch, 6 Amps, one way, 240 volts, 1 module complete all as specified and directed.

S&F modular switch 16 Amps, one way, 240 volts, 1 module complete all as specified and directed.

S&F modular socket, 6/16 Amps, 2/3pin combined, 2 module AC 240 volts complete all as specified and directed.

S&F angle holder, insulated polycarbonate body with back plate complete all as specified and directed.

S&F ceiling rose PVC polycarbonate isolated body, 3 terminals 230 Volt complete all as specified and directed

S&F modular hum free electronic step fan regulator 120-280 volts of 120 watts capacity including connecting up complete all as specified and directed.

S&F modular bell push, 6 Amp, 1 module complete all as specified and directed.

S&F door bell AC 240 volts, single pole complete all as specified and directed.

S&F in repair MCBs Distribution board SPN, 8 ways, powder coated CRCA steel sheet, degree of protection IP-43, IK-09 with reversible double door, 240V, recess mounted having insulated 200 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs incl taking down old U/S DB complete all as specified and directed. Note : MCBs and MCB DB shall be of the same make.

S&F MCBs of 'B' curve, single pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked, 240Volts including required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed.

S&F MCBs of 'B' curve, Double pole 40 to 63 Amps having breaking capacity 10 KA, ISI marked, 240Volts including required wiring connections with copper lugs of suitable size provided in MCB DBs incl connection testing and commissioning complete all as specified and directed.

S&F LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficiency of 105 lumen per watt and total power consumption not more than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed. Make - Philips Cat part BN308C LED20S-6500 L120 PSU WH, Crompton Cat part CIS-305-40-57-SL-DP-NWH, Havells Cat no STOUTPLUS600BS20WLED840SPCWH.

S&F LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficiency of 105 lumen per watt and total power consumption not more than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed. Make - Philips Cat part BN308C LED20S-6500 L120 PSU WH, Crompton Cat part CIS-305-40-57-SL-DP-NWH, Havells Cat no STOUTPLUS600BS20WLED840SPCWH.

S&F in repair LED bulk head light fitting 9 watt IP 66 & IK 09 with with pressure die cast aluminium housing & polycarbonate diffuser duly prewired connection with 0.75sqmm PVC insulated & sheathed three core flexible multi stranded copper conductor cable complete all as specified & directed.

S&F exhaust fan, high speed, steel body 300mm sweep, 1400 RPM, four blade, heavy duty motor, copper wound double ball bearings, grey colour with louver, nuts, bolts and washers incl three core 0.75sqmm copper cable connection with protective steel bird guard fixed in wall including making suitable size opening and making good the disturbed portion as per existing complete all as specified & directed.

Taking down carefully exhaust fan any sweep, metal body with louvers, fan motor and accessories complete and including minor repair and refixing the same after repairing at new or old location complete all as specified and directed.

S&F in replacement fresh air fan of sweep 300 mm, made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, 1200 RPM, copper winding incl making connections complete all as specified and directed.

S&F ceiling fan 1200mm sweep 50 Hz AC 230 votls, white colour with BLDC fan motor, Min air delivery 210 CFM with service value 6.00 BEE 5 star rated incl blade set, 0.45 mtr down rod, canopy set, rubber reel including 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and writing MES No. on fan body as required complete all as specified and directed.

M&L for taking out ceiling fan 1200mm sweep 50Hz AC 230 volts and refixing at new location including minor repair and replacement of fan blade, down rod, nut, bolt and washer and spray painting in existing colour including 0.5sqmm thre core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling as required and writing MES No. on fan body complete all as specified and directed.

M&L for earthing complete with galvanized steel earth plate electrode of size 60cmx60cmx6.0mm buried directly in ground, vertically to depth not less than 2.25mtr below normal ground level with top edge of the earth plate at depth not less than 1.5 metre below ground level surrounded from all sides with alternate layers of charcoal and common salt and connected to GI lead wire 4.0mm dia by means of GI bolts, nuts washers & check nuts electrode connected to main switch board or main control board or on poles or on transformer and GI pipe medium grade 20mm bore for watering, 40mm bore GI pipe medium grade for protection of GI wire upto test point including providing funnel and wire mesh GI frame and 10cm thick suitably reinforced RCC pit cover, PCC chamber pit with PCC (1:3:6) type C2 using 40mm graded stone aggregates complete including excavation and earth work in any type of strata, disposal of surplus soil to a distance not exceeding 50 mtr, all as specified ans shown in Electrical plate No. 3 of SSR Part-1, PCC pit shall be provided at least 50 cm away from the earth pit and not just on earth pit including testing on completion complete. (Note - GI lead wire size 4.0mm upto 7.5 m included in the item).

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ