PROVISION OF CERTAIN SPECIAL REPAIR, LBW, REV AND MINOR WORKS, AT KOLHAPUR IN THE AREA OF AGE B/R (EAST) UNDER GE (NORTH) PUNE

Amount

Surface excavation not exc. 30 cm deep and averaging 15 cm deep and getting out in soft/ loose soil complete all as specified and as directed.

Excavation over areas not exc.1.5 metres deep and getting out in soft/ loose soil complete all as specified and directed.

Excavation over areas not exc.1.5 metres deep and getting out in hard /dense soil complete all as specified and directed.

Excavation in trenches not exc. 1.5 m wide and not exc. 1.5 m in depth for foundation, cable etc. or for shafts, wells, cesspits, manholes, pier holes, pole etc. n. exc 10 sq m on plan and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick with soils complete all as specified and as directed.

Removing of excavated material (soil) to distance not exc.50metres and deposited where directed at a level not exc.1.5 metre above the starting point complete all as specified and as directed.

Surface dressing n exc 15 cm deep in soft/ loose soil complete all as specified and as directed.

Material and labour for hardcore broken stone or boulders of gauge exc. 63mm but not exc. 100mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified and as directed.

Material and labour for moorum/ red bazri filling under floors with moorum brought from outside MD land, laid in layers n. exc 15 cm thick spread, levelled and rammed including watering etc complete all as specified and directed.

Material and labour for PCC (1:3:6) type C-1 (using 20 mm graded broken stone aggregate) as in filling in chowkats, bed blocks complete all as specified and as directed.

Material and labour for PCC (1:2:4) type B-1 (using 20 mm graded broken stone aggregate) as in benching, kerb, coping of manholes and the like including weathering, slightly rounded or chamfered angles and throating including use & waste of necessary form work complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C-1 (using 20 mm graded broken stone aggregate) as in coping, coping of poles, stays etc. including use and waste of form work, surface finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for precast solid cement concrete block masonry exc.10cm width using solid blocks of PCC design mix grade C5 set in cement mortar (1:6) complete all as specified and directed.

M&L Brick work with sub class 'B' old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:4 complete all as specified and directed.

Material and labour for precast RCC (nominal mix ) (1:2:4) type B-1, (using 20mm graded broken stone aggregates) as in manhole covers including form work/ mould complete all as specified and as directed.

Material and labour for RCC (design mix) M-30 (using 20mm graded broken stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M&L for RCC M-30 (using 20mm graded broken stone aggregate) in wall, retaining walls, basement walls, ballast walls and the like any thickness above top of footings including attached pilasters and buttresses complete all as specified and as directed..

Material labour for RCC (design mix) M-30 (using 20mm graded broken stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Material labour for RCC (design mix) M-30 (using 20mm graded broken stone aggregates) as in beams, cantilevers, bressummers, lintels over 1.50m span complete all as specified and as directed.

Material labour for RCC (design mix) M-30 (using 20mm graded broken stone aggregates) as in columns, pillars, piers,posts and struts complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

Material and labour for cutting holes in brick/ concrete walls built in cement mortar and making good in cement mortar 1:3 or cement concrete (1:2:4) type B1 (using 20mm graded broken stone aggregate) as required, superficial area n.exc150 Sqcm complete all as specified and as directed.

Material and labour for 20mm thick granite (of any type) work ( table rubbed and polished) in steps , jambs. pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Material and labour for formwork to sides of concrete foundations, footings, bases of column, raft and raft beams, side and soffit (if any ) of foundation and plinth beam and similar works, vertical or batter etc vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed.

Material and labour for formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses etc vertical or to batter for rough finished flat surfaces of concrete complete.

Material and labour for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc. 200 mm thick for fair finished flat surfaces of concrete all as specified and as directed.

Material and labour for formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves, bands, including supports, overhangs, etc. for fair finished flat surfaces of concrete complete all as specified and as directed.

Material and labour for formwork to sides of pillars, posts, struts, columns and stanchions, square, rectungular or polygonal for fair finished flat surfaces of concrete complete all as specified and as directed.

Material and labour for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n. exc. 20cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc.10cm but n.exc. 20cm wide for fair finished surfaces complete all as specified and as directed.

Material and labour for 2nd class hardwood, plain, solid straigtht chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, in pieces for replacing one side or certain portion of decayed portion without taking down chowkat or frame including making good disturbed portion with cement mortar (1:4) complete all as specified and as directed .

Supply and fix for 30mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze,etc.(without sash bars), edges of framing plain,chamfered or rounded, fitted with cut and mitred beads for securing glass,etc; for windows, ventilators etc. the size of the rail and stile as specified in SSR Par-I, Section 8, clause 8.24 (b) complete all as specified and as directed.

Supply and fix for 30mm thick flush shutters solid core construction, with block board core and plywood face panels, commercial type on both sides including 4mm thick teak wood edging on all sides complete all as specified and as directed

Taking down chowkats or frames with shutters (without taking off shutters from frame) area not exc.1.5 sqm each complete all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frame) area exc.1.5 sqm and not exc.4 sqm each complete all as directed

Taking down shutters of any description, area exc.1 sqm and not exc. 2 sqm each complete all as directed.

Taking down door shutter of any description, area exc.1sqm and not exc. 2 sqm each and refixing in same opening after making necessary repair, easing and adjusting complete all as directed.

Supply and fix for solid PVC door frame of size 50mm x 47mm, made out of 5 mm thick plain colour PVC sheet, reinforced with mild steel square tube complete all as specified and as directed.

Supply and fix Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with wood free EPS supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

Supply and fix for 150 mm long aluminium anodised, barrel tower bolts of extruded section, fixed with stainless steel screws complete all as specified and as directed.

Supply and fix for 200 mm long aluminium anodised, barrel tower bolts of extruded section, fixed with stainless steel screws complete all as specified and as directed.

Supply and fix for 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and as directed.

Supply and fix for 75mm size stainless steel butt hinges fixed with stainless steel screws complete all as specified and as directed.

Supply and fix for 125mm size aluminium handles, anodised, cast type complete all as specified and as directed.

Supply and fix for 150mm size extruded aluminium alloy handles fabricated type anodised fixed with stainless steel screws complete all as specified and as directed.

Supply and fix in repairs, 25mm bore aluminium powder coated fancy type curtain rod as per sample kept in GE (N) Pune office complete all as specified and as directed.

Supply and fix in repairs, aluminium powder coated fancy type decorative brackets suitable for 25 mm dia curtain rod (minimum projection from wall 75 mm ) fixed to wall including drilling, rawl plug, screws etc complete all as specified and as directed.

Supply and fix tubular towel rail brass chromium plated, 20mm dia, D type, 60cm long between flanges including brackets with brass screws and wooden plugs complete all as specified and as directed.

Taking out unserviceable wire net of any description from steel windows, ventilators, verandah frame by taking out old flat iron flats and removing the same from site and supply and fix for galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples including flat iron fillets 12x3mm size with nut & bolts complete all as specified and as directed.

All as per serial item No. 48 here-in-before but from wooden frame with and including 2nd class HW wooden beads not exc.3 Sqcm cross section.

Supply and fix for stainless steel wire cloth 0.36 mm nominal dia of wire, average width of aperture 1.40 mm, fixed with stainless steel wire staples complete all as specified and as directed

Taking out old rusted/ unserviceable mild steel work such as steel windows/ ventilators shutters with guard bar fly proofing shutter and other section etc. and removing same from work site including necessary cutting in brick walls complete all as directed.

Supply and fix for mild steel framed work such as in grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

Supply and fix for framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, reveting, etc. not exc 10 kg each brackets, conforming to Fe-290 Grade-E-165 complete all as specified and as directed.

Supply and fix for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

S & F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 05cm and n exc 10cm long, diameter of neck 5 to 10mm complete all as specified and as directed

Material and labour for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia. or securing with clips complete all as specified and as directed.

S&F for expanded metal, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members, weight per sqm n. exc. 4 Kg complete all as specified and as directed.

Supply and fix for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including applying one coat of red oxide primer complete all as specified and as directed.

All as per serial item No.59 here-in-before but without glazing bars.

Supply and fix for pressed steel frames of size 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, as per ISI mark, complete all as specified and as directed .

Supply and fix for pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, as per ISI mark, complete all as specified and as directed .

Supply and fix for aluminium anodised louvered ventilator with adjustable louvers using standard aluminium section as specified including glass 4mm thick frosted and stainless steel wire mesh 0.36mm dia wire and 1.40mm aperture etc complete all as specified and directed.

Material and labour for 0.63mm thick plain, black, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) complete all as specified and as directed.

Taking down old existing tarfelt of any type and course, from roof surface including adjoining parapets and removing the material to a distance exceeding 50m but n.exc. 100m including roughening old concrete surfaces by tucking & rubbing with wire brushes and cleaning the surfaces with water to remove all loose dust etc. complete all as specified and derected.

Cutting out cracks to 'V' section (shape) in existing roof slab or terracing cleaning out, wetting and grouting with cement and sand slurry (1:3) complete all as specified and as directed.

Material and labour for water proofing treatment to RCC roof slab including parapet complete all as specified below and as directed by Engineer-in-Charge including testing :-(a) On the dried plastered surface, one coat of approved bituminous primer @ 0.40 Litre/Sqm. Bituminious primer shall be 'Tar Mastic' manufactured by M/S STP LTD or 'EMW FLATE' manufactured by M/S Texsa India Ltd. or equivalent of make as per particular specifications as approved by GE. (b) On this primered surface, APP modified bituminous polymeric memberance 3mm thick weighing not less than 3.60 Kg/Sqm with plain finish reinforced with non woven polyester fabric weight not less than 150gms per Sqm. Polymeric members shall be taken to a height of 60cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrance flashing. (c) Application of two coat of bituminous aluminium paint over the polymeric membrane after necessary preparation and cleaning. Note :- (i) Laying APP based polymeric membrance shall be done by torch application method or as per manufacturers instructions. (ii) A minimum overlap of 150mm shall be made at the end and 100mm shall be made at the longitudinal sides of the polymeric membrance respectively and sealed all ovelaps and joints as per Manufacturers instructions. (iii) APP based polymeric membrance shall be "SUPER THERMOLAY" manufactured by M/S STP LTD or MOPOLY FP manufactured by M/S Texsa India Ltd. or equivalent of make as per particular specifications as approved by GE.

Supply and fix in repairs for 12mm thick particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, including 4mm thick teak wood edging externally, fixed with screws to timber frame work as in cup board shutters complete all as specified and as directed.

Supply and fix in repairs for 18mm thick particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, including 4mm thick teak wood edging externally, fixed with screws to timber frame work as in cup board shutters complete all as specified and as directed.

M & L machine cut cudappah stone slab 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Material and labour 75mm thick PCC (1:4:8) type D2 (using 40mm graded broken stone aggregate) as in sub base complete all as specified and as directed.

Material and labour 100mm thick PCC (1:3:6) type C2 (using 40mm graded broken stone aggregate) as in sub base complete all as specified and as directed.

Material and labour 50mm thick PCC (1:3:6) type C2 (using 40mm graded broken stone aggregate) as in sub base complete all as specified and as directed.

Material and labour 75mm thick PCC (1:3:6) type C2 (using 40mm graded broken stone aggregate) as in plinth protection/ courtyard/ foot path/ hard standing finishing the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour 40mm thick PCC (1:2:4) type B1 (using 20mm graded broken stone aggregate) as in floor topping finishing the surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for roughing surfaces of old concrete floor by picking, sweeping, cleaning and washing down with water to remove dust, etc. complete all as per specified and as directed.

Material and labour for coloured glazed ceramic tiles of minimum size 300mm x 200mm x 7mm thick as in vertical surface such as dado/ skirting and of colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick backing coat in cement mortar (1:3) complete all as specified and as directed.

Material and labour for coloured glazed ceramic tiles of minimum size 300mm x 450mm x 7mm thick as in vertical surface such as dado/ skirting and of colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick backing coat in cement mortar (1:3) complete all as specified and as directed.

Material and labour for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.11sq.m but not exceeding 0.18sq.m as in floor etc., colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

Material and labour for coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.18sq.m but not exceeding 0.38sq.m as in floor etc., colour and pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles, laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed.

Material and labour for machine pressed precast cement concrete coloured interlocking tiles, paver block, any shape and size as approved, 40mm thick, conforming to IS 15658-2006, M-35 grade with grey cement and pigments in floor/ pavement laid over and including 25mm thick sand cushioning laid dry to the profile including vibrating with surface vibrator after laying of tiles complete all as specified and as directed. NOTE: (i) Manufacturers test certificate shall be submitted alongwith sample.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as directed.

Material and labour for 5mm thick rendering in cement mortar (1:4) on ceiling finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 15mm thick in CM (1:6) on other than fair faces of brickwork or concrete surfaces or stone wall finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of concrete roof surfaces to maintain proper slope, finished even and smooth without using extra cement mixed with integral water proofing compound as per manufacturer's instructions complete all as specified and as directed. (Note: Supply only waterproofing compound will be measured and paid separately).

Material and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of brick/ concrete surfaces, finished even and smooth without using extra cement mixed with integral water proofing compound as per manufacturer's instructions complete all as specified and as directed. (Note: Supply only waterproofing compound will be measured and paid separately).

Taking down cement plaster any description on brick/ block/ stone walls, roof etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Material and labour for preparation of newly plastered or unplastered surfaces of ceiling and applying three coats of white wash all as specified and as directed.

Material and labour for preparation of newly plastered or unplastered wall surfaces and applying two coats of oil bound/ acrylic distemper over a coat of alkali resistant priming paint complete all as specified and as directed.

Material and labour for complete removal of existing treatment on walls, preparation of surfaces and make the surfaces free from loose particles, oil stains etc., preparing surfaces and applying two coats of oil bound/ emulsion distemper over a coat of alkali resistant priming complete all as specified and as directed.

Material and labour for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and as directed

Material and labour for complete removal of existing finish/treatment on wall surfaces, preparing surface and make surface free from loose particles, oil stains etc and applying two coats of cement based paint on wall complete all as specified and as directed.

Material and labour for hacking out old broken glass (any thickness, size, and quality of description) from metal/ wooden frame including punching or drilling out old glazing pins, spring clips and providing and fixing new ones complete all as specified and as directed.

Supply and fix 3mm thick sheet glass, ordinary quality and glazing with oil putty/ bead in square not exc. 0.5sqm in each pane complete all as specified and as directed.

Material and labour for preparation of new untreated wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of old surfaces of wood and wood based material of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

Material and labour for preparation of new steel or iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

Material and labour for preparation of old painted steel surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed.

Supply and fix for 20mm bore steel water tubing 'medium grade' galvanised, with all fittings as in trenches complete all as specified and as directed.

Supply and fix for 15mm bore steel water tubing 'medium grade' galvanised, with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

Supply and fix for 20mm bore steel water tubing 'medium grade' galvanised, with all fittings and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing with all fittings and connections complete all as specified and as directed.

Taking up or down 25 mm bore steel tubing with all fittings and connections complete all as specified and as directed.

Taking up or down 40 mm bore steel tubing with all fittings and connections complete all as specified and as directed.

Supply and fix for 500 litres capacity, rotational moulded polythelene water storage tanks (ISI marked) (three layer, cylindrical vertical with closed top), hoisted and fixed in postion including 20mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210gms) including dismantling existing tank complete all as specified and as directed.

Supply and fix for 2000 litres capacity, rotational moulded polythelene water storage tanks (ISI marked) (three layer, cylindrical vertical with closed top), hoisted and fixed in postion including 20mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210gms) including dismantling existing tank complete all as specified and as directed.

Supply and fix for 7500 litres capacity, rotational moulded polythelene water storage tanks (ISI marked) (three layer, cylindrical vertical with closed top), hoisted and fixed in postion including 25mm size brass float valve, high pressure, with polythene float and flynut and connected fittings including dismantling existing tank complete all as specified and as directed.

Supply and fix in repair bib tap for 15mm bore pipe, chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

Supply and fix bib tap for 15mm bore pipe, chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

Supply and fix pillar tap for 15mm bore pipe, cast copper alloy, with capstan heads, chromium plated, cast copper alloy, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed. Make: Jaquar, Prayag

Supply and fix brass chromium plated mixer for mixing hot and cold water screwed down high pressure for iron pipe of 15mm bore complete all as specified and as directed.

Supply and fix stop valves for 20mm bore pipe, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fix stop valves for 25mm bore pipe, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fix stop valves for 15mm bore pipe, fancy type, chromium plated, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fix stop valves for 15mm bore pipe, fancy type, chromium plated with long shank and cup (concealed type), cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fix waste coupling of PTMT (half or full threaded) (minimum weight 45gms) for 32mm bore dia discharge pipecomplete all as specified and as drected.

Supply and fix waste coupling of PTMT (half or full threaded) (minimum weight 60gms) for 40mm bore dia discharge pipecomplete all as specified and as drected.

Supply and fix for grating doom round 100mm dia of PTMT (minimum weight 25gms) complete all as specified and as drected.

Supply and fix for grating round 140mm size of PTMT (minimum weight 50gms) complete all as specified and as drected.

Supply and fix for 15mm size PVC connection 450mm long including PTMT nuts etc complete all as specified and as directed

Supply and fix in repair for PVC (SWR) pipe 110mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

Supply and fix for PVC (SWR) bends any radius of 110mm bore complete all as specified and as directed.

Supply and fix for PVC (SWR) floor trap 75 mm dia of outlet, plain with grating including jointing with solvent cement fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed

Supply and fix in repair for PVC (SWR) floor trap 75 mm dia of outlet, plain with grating including jointing with solvent cement fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed

Material and labour for PCC (1:3:6) type C2 ( using 40mm graded broken stone aggregates) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm bore of pipe all as specified and as directed.

Material and labour for PCC (1:3:6) type C2 ( using 40mm graded broken stone aggregates) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 200mm bore of pipe all as specified and as directed.

Material and labour for 150mm bore RCC pipes, class NP3 laid and jointed with collars and tested complete all as specified and as directed.

Material and labour for 200mm bore RCC pipes, class NP3 laid and jointed with collars and tested complete all as specified and as directed.

Supply and fix for vitreous china European type wash down water closet pan, (Pedestal pattern) white with P or S trap including plastic water closet white closed pattern with flat bottom and cover with mild steel chromium plated hinging device and fixing bolts, necessary inlet and outlet connections including PVC low level flushing cistern 10 litres capacity, valveless, syphonic action type, white with inlet, ball valve, float and handle including brackets and PVC flush pipe 32mm dia complete all as specified and as directed.

Supply and fix in repairs for vitreous china, squatting pan, 'Orissa' pattern, size 580 mm x 440 mm, white, front or back inlet and foot rests any pattern, including making good to floor and concrete, connections to trap, inlet, outlet, anti-syphonage pipes, etc. complete all as specified and as directed.

Supply and fix in repairs 10 litres capacity PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, 32mm dia PVC flush pipe and connections to pipes, making good the disturbed surfaces complete all as specified and as directed.

Supply and fix for vitreous chinaware wash hand basin, white, flat back, size 550x400 mm, CP waste coupling, chain and plug, waste fittings, union and PVC waste pipe 32 mm dia 90cm long, 15mm dia PVC connection 450mm long including PTMT check nuts and all necessary inlet outlet connections including CI brackets complete all as specified and as directed.

Supply and fix in repair for vitreous chinaware wash hand basin, white, flat back, size 550x400 mm, including cutting for and pinning in ends of and including brackets or erecting stand and waste pipe 32 mm dia of required length and all necessary inlet outlet connections complete all as specified and as directed.

Supply and fix for chromium plated jet spray for WC with 100cm long PVC pipe including necessary GI fittings like toe, nipple etc. complete all as specified and as directed. (Make CERA or equivalent as approved)

Supply and fix in repair brass chromium plated fancy type shower rose 125mm size with swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed.

Supply and fix in repair brass chromium plated shower arm 15 mm size, minimum 195mm long with bend of 45 degree with flange complete all as specified and as drected.

Supply and fix for stainless steel sink made of Stainless Steel, 1mm thick with drainage board made of 1mm thick sheet, with plug, washers and waste coupling, waste pipe, including bedding in cement mortar to dwarf wall or cast iron cantilever brackets and connecting union to pipe, over all size 915 mm x 460 mm with bowl size 410mm X 330mm X 160mm all as specified and directed.

Supply and fix in repair for stainless steel plate rack of size 24 inch x 36 inch x 10 inch, made out of 0.63mm thick stainless steel sheet (Grade AISI 304 18/8), S S screws and round pipe, fixed to wall with screws complete all as specified and as directed. Make – Blue Star Silver Shine Cat No.SSKPR-312 or equivalent from Nirali/ Jain Brothers Sanitation Pvt Ltd (Jayna )/ Prayag as approved by GE.

Dismantling of stone slabs and tiles of any description or thickness in floor, apron etc., laid bedded and pointed in any mortar complete all as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as directed.

Supply and fix, laying and jointing for UPVC pipes (SCH-40) 50mm bore including necessary fittings such as bends, elbows, tees, unions, reducers, clamps, jointing materials etc laid in trenches complete all as specified and as directed.

Supply and fix, laying and jointing for UPVC pipes (SCH-40) 75mm bore including necessary fittings such as bends, elbows, tees, unions, reducers, clamps, jointing materials etc laid in trenches complete all as specified and as directed.

Supply and fix, laying and jointing for UPVC pipes (SCH-80) 100mm bore including necessary fittings such as bends, elbows, tees, unions, reducers, clamps, jointing materials etc laid in trenches complete all as specified and as directed.

Supply and fix and jointing for UPVC pipe 25mm bore of pressure rating 10kgf/cm2 fixed complete to walls, ceilings or in floors etc. including all fittings and accessories like unions, beds, tee, elbow, sockets, jointing materials etc complete.

Supply and fix and jointing for UPVC pipe 20mm bore of pressure rating 10kgf/cm2 fixed complete to walls, ceilings or in floors etc. including all fittings and accessories like unions, beds, tee, elbow, sockets, jointing materials etc complete.

Supply and fix and jointing for UPVC pipe 15mm bore of pressure rating 10kgf/cm2 fixed complete to walls, ceilings or in floors etc. including all fittings and accessories like unions, beds, tee, elbow, sockets, jointing materials etc complete.

M&L for gravity flow filter unit 50mm bore as specified in para 29.2.5 of SSR Part-I including Purpose built filter of size 3mx3mx1.5m and the filter material shall consist of coarse sand of 1.5 to 2mm size at the top, followed by gravel of 5 to 10mm size and boulders of 5 to 20 cm at bottom, the thickness of each layer shall be about 0.5m complete and all as specified in para 29.2.5.3.2. of SSR Part-I and as directed by Engr-in-Charge. Note: Excavation, earth work and brick work shall be measured and paid for separately.

Material and labour for hardcore broken stone or boulders of gauge exc. 63mm but not exc. 100mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface complete all as specified and as directed.

Taking down/ out unserviceable LT cables of any cross sectional area and connections and joints including pipes, bricks etc of any description laid in trenches or fixed with walls/ poles, complete all as directed. Note: Excavation and earth work shall be measured and paid separately.

Supply, laying and testing for LT XLPE UG cable insulated screened PVC bedded galvanised steel strip or wire armoured, heavy duty electric power cables with stranded aluminium conductor 1100 volts grade with cable glands, lugs etc laid in trenches, fixed on wall/ pole including brass cable glands, clamps etc. of size 10 Sqmm 4 core cable complete all as specified and as directed. Note: Excavation and earth work, sand cushioning, brick protection, GI pipe shall be measured and paid separately.

All as per serial item No. 153 here-in-before but for 16Sqmm 4 core cable.

All as per serial item No. 153 here-in-before but for 25 Sqmm 4 core cable.

Taking down carefully unserviceable point wiring of any description/ type/ size of light/ fan / tube/ power / two way/ bell etc. on TW batten/ conduit including removal of batten/ conduit/ gutties/ wooden boards/ switch/ sockets/ regulators/ holders/ ceiling roses/ call bells etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ ceiling so as to match with the existing finishes complete all as directed.

Taking down the existing unserviceable main switch/ cut out/ MCB DBs/ sheet metal enclosure of any type/ capacity/ description as existing at site including MCBs any type/ capacity and making good the disturbed surfaces of wall/ ceiling to match with the existing finishes complete all as directed.

Taking down the unserviceable submain wiring of any type/ description as existing at site including making good the disturbed surfaces to match with the existing finishes complete all as directed.

Taking down the existing unserviceable street security light fitting any type/ capacity from pole including disconnecting and removing pipe bracket etc. and making good the disturbed surfaces of wall/ ceiling to match with the existing finishes complete all as directed.

Taking down the existing unserviceable tube light, decorative wall mounted, bulk head, batten aluminium, bollard light fitting any type/ capacity and making good the disturbed surfaces of wall/ ceiling to match with the existing finishes complete all as directed.

Taking down the unserviceable earthing and making good the disturbed surfaces complete all as directed.

Material and labour for point wiring using approved colour coding as per IS, with multistranded FRLS copper conductor 1.5 Sq. mm (nominal area), two single core PVC insulated and unsheathed multistranded cable 1100 volts grade ISI-694 marked through and including heavy duty ISI marked, 20 mm dia rigid PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ ceiling etc, with GI terminal sunken boxes 1.2mm thick 60mm deep of suitable size as per site requirement, covered with modular white cover plate with frame suitable for housing modular switches, sockets, regulators etc. including PVC insulated multistranded FRLS copper conductor 1.5 Sqmm (nominal area) single core cable as earth continuity conductor and connecting to the common earth dolly for one light point controlled by one, one way switch 5 Amps complete all as specified and as directed.

All as per serial item No.162 here-in-before but point wiring for one ceiling/ exhaust fan point controlled by one, one way switch 5 Amps and regulator.

All as per serial item No.162 here-in-before but point wiring for one 3 pin 5 Amps socket outlet controlled by one switch on same board.

All as per serial item No.162 here-in-before but point wiring for one 3 pin 5 Amps socket outlet controlled by one switch on independent board.

All as per serial item No.162 here-in-before but point wiring for one bell point controlled by one bell switch 5 Amps.

All as per serial item No.162 here-in-before but point wiring for one light point controlled by two, two way switchs 5 Amps.

All as per serial item No.162 here-in-before but with FRLS copper conductor 2.5 Sqmm (nominal area), single core, PVC insulated and unsheathed multistranded cable 1100 Volt grade ISI-694 marked including PVC insulated multistranded FRLS copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor for 3 pin 15 Amps socket outlet on independent board.

Material and labour for point wiring using approved colour coding as per IS, with multistranded FRLS copper conductor 1.5 Sq. mm (nominal area), two single core PVC insulated and unsheathed multistranded cable 1100 volts grade ISI-694 marked through and including heavy duty ISI marked, PVC casing and capping including all accessories, GI sunken/ surface boxes 1.2mm thick 60mm deep of suitable size as per site requirement, covered with 3mm thick hylem sheet, ISI marked for switches, sockets, regulators etc. including PVC insulated multistranded FRLS copper conductor 1.5 Sqmm (nominal area) single core cable as earth continuity conductor and connecting to the common earth dolly for one light point controlled by one, one way switch 5 Amps complete all as specified and as directed.

Supply and fix for lamp holder, PVC body/ polycarbonate type with back plate suitable batten/ slanting fittings complete all as specified and as directed.

Supply and fix for modular switch, one way 6 Amps, 1 module complete all as specified and as directed.

Supply and fix for modular switch, one way, 16 Amprs, 1 module with neon indicator complete all as specified and as directed.

Supply and fix for modular switch, two way 6 Amps, 1 module complete all as specified and as directed.

Supply and fix for modular bell push, 6Amps, 1 module complete all as specified and as directed.

Suply and fix for bell electric ding dong type suitable for operation on 230 volt 50 HZ A C supply including taking down existing complete all as specified and as directed

Supply and fix for modular socket outlet multi purpose 2/3 pin 6 Amps, combined 2 module complete all as specified and as directed.

Supply and fix for modular socket outlet multipurpose, 2/3 pin, 6/16 Amps, combined 2 module complete all as specified and as directed.

Supply and fix for modular step type fan regulator 120 watt 1 module suitable for 230 volt 50 Hz AC supply including taking down of existing complete all as specified and as directed.

Supply and fix for switch piano flush type, single pole, one way, 6 Amp complete all as specified and as directed.

Supply and fix for sheet metal enclosures single pole and neutral with a two pin and earth plug and socket complete with one MCB SP 20/32 Amp complete all as specified and as directed.

Supply and fix for ceiling rose, 2/3 terminals, PVC/ polycarbonate type, isolated body suitable ISI marked complete all as specified and as directed.

Supply and fix for sheet metal enclosure MCB DB SPN 12 way with 200 Amps rated bus bar 240 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc and making good of disturbed surface to match with existing colour of wall complete all as specified and as directed. Make: L&T Cat No. DBSPN012DD or equivalent of Legrand, ABB

Supply and fix for sheet metal enclosure MCB DB TPN 4 way with 200 Amps rated bus bar 415 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc and making good of disturbed surface to match with existing colour of wall, connecting complete all as specified and as directed.

Supply and fix for MCB SPN rated capacity 40 Amps, 240 Volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

Supply and fix for MCB SP rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

Supply and fix for MCB TPN rated capacity 63Amps, 415Volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

Supply and fix for highly efficient LED bulbs 10W with lumens out put not less than 1000 lumens, used as ready replacement for existing GLS/ CFL direct fit lamp in B-22 cap of make Havells/ Philips/ Wipro/ Bajaj/ HPL as approved complete all as specified and as directed.

Supply and fix for LED 10 watts batten aluminium extruded with decorative end caps all as per Cat No. BCLSB 10 NW/ WH of make Bajaj, Wipro Cat No. LL20-111-XXX-65-NE or its equivallent model in Havells, Philips as approved complete all as specified and as directed.

Supply and fix for energy saving new generation 10 watts LED bulk head fitting IP-65 luminaire with opal diffuser prewired and necessary mounting arrangements, provision of 3 core multistranded copper conductor of size 23/0.193 from ceiling rose with LED bulb all as per Cat No.BIBWP 10W LED of make Bajaj/ Philips Cat Part No WT140LED 7SCW PSU or its equvalent in Wipro/ Havells complete all as specified and as directed.

Supply and fix for wall mounted LED 20watts with lumens out put not less than 2000 lumens, box type (decorative) light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver connector block etc complete with all accessories internally pre wired all as per Cat No. BCLAB 20W of make Bajaj, Cat No. LL20-281-XXX065-ALI of Wipro or equvalent of make Philips/ Havells/ Syska/ Jaguar as approved and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 4' x 20watts complete all as specified and as directed.

Supply and fix for energy saving new generation environmental friendly long life versatile pressure die aluminium IP-66 for security light fitting luminaire of capacity 15 watt with high power LEDs as light source and electronic driver with lumens out put not less than 1500 lumens, with prewired of make Bajaj Cat No. BRLEP 15 W LED, Philips Cat No. BRP040 or equvalent of make Wipro/ Havells/ Crompton as approved, necessary mounting arrangements and provision of 2.5 Sqmm 3 core copper conductor cable multistranded from ceiling rose to light fitting including 40mm dia 1.5 metres long GI pipe medium grade bracket of suitable shape with clamps made out of MS flat iron of size 40mm x 6mm, nuts, bolts including taking down old existing unsesrviceable tube light fitting complete all as specified and as directed.

Supply and fix for energy saving new generation environmental friendly long life versatile pressure die aluminium IP-66 for security light fitting luminaire of capacity 25 watt with high power LEDs as light source and electronic driver with lumens out put not less than 2500 lumens, with prewired all as per Cat No. BRLEP 25 W LED WH (Edge plus series) of make Bajaj, Philips CAT part No. BRP042 LED HP CW 25W or equivalent of make Wipro/ Havells/ Crompton/ as approved, necessary mounting arrangements and provision of 2.5 Sqmm 3 core copper conductor cable multistranded from ceiling rose to light fitting including 40mm dia 1.5 metres long GI pipe medium grade bracket of suitable shape with clamps made out of MS flat iron of size 40mm x 6mm, nuts, bolts complete all as specified and as directed.

Supply and fix for energy saving new generation environmental friendly long life versatile pressure die aluminium IP-66 for security light fitting luminaire of capacity 45 watt with high power LEDs as light source and electronic driver with lumens out put not less than 4500 lumens, with prewired all as per Cat No. BRTFG 45 W LED WW of make Bajaj, Philips Cat No. BRP052 or equivalent of make Wipro/ Havells/ Crompton as approved, necessary mounting arrangements and provision of 2.5 Sqmm 3 core copper conductor cable multistranded from ceiling rose to light fitting including 40mm dia 1.5 metres long GI pipe medium grade bracket of suitable shape with clamps made out of MS flat iron of size 40mm x 6mm, nuts, bolts complete all as specified and as directed.

S & F for Energy saving new generation environmental friendly LED security light luminaire with long life versatile pressure die-cast housing with toughened glass and individual LEDs with secondary optics and IP 66 protection with high power LEDs as light source and electronic driver of capacity 60 watts with lumens out put not less than 6000 lumens with pre wired and necessary mounting arrangementsnd provision of 4 sq mm twin core copper conductor cable multi stranded from fitting to junction box including necessary GI pipe medium braket of required dia 1.5 mtr long bend to required shape with suitable with MS clamps made out of flat iron of size 40 x 6 mm - 02 sets, bolt & nuts complete all as directed by Engineer- in-charge. Make :- Bajaj Cat No BRTFG 60W LED I or its equvalent in Philips, Wipro.

S & F for Energy saving new generation environmental friendly LED security light luminaire with long life versatile pressure die-cast housing with toughened glass and individual LEDs with secondary optics and IP 66 protection with high power LEDs as light source and electronic driver of capacity 100 watts with lumens out put not less than 9000 lumens with pre wired and necessary mounting arrangementsnd provision of 4 sq mm twin core copper conductor cable multi stranded from fitting to junction box including necessary GI pipe medium braket of required dia 1.5 mtr long bend to required shape with suitable with MS clamps made out of flat iron of size 40 x 6 mm - 02 sets, bolt & nuts complete all as directed by Engineer- in-charge. Make :- Bajaj Cat No BRTFG 100W LED WW or its equvalent in Philips, Wipro.

Supply and fix for energy saving new generation environmental friendly long life versatile presure die cast housing and heat sink in aluminium extrusion IP 66 flood light fitting luminaire 80watts with secondary optics, high power LEDs as light source and electronic driver of capacity 80 watts with lumens out put not less than 8000 lumens,with pre wired suitable for sports lights complete all as per Cat No.BARFEG 80W LED of make Bajaj or equivalent of make Philips, Wipro, Havells, Syska, Jaguar as approved and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

Supply and fix for energy saving new generation environmental friendly long life versatile presure die cast housing and heat sink in aluminium extrusion IP 66 flood light fitting luminaire 160watts with secondary optics, high power LEDs as light source and electronic driver of capacity 160 watts with lumens out put not less than 16000 lumens,with pre wired suitable for sports lights complete all as per Cat No.BARFEG 160W LED of make Bajaj or equivalent of make Philips, Wipro, Havells, Syska, Jaguar as approved and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

Supply and fix for energy saving new generation environmental friendly long life versatile presure die cast housing and heat sink in aluminium extrusion IP 66 flood light fitting luminaire 180watts with secondary optics, high power LEDs as light source and electronic driver of capacity 180 watts with lumens out put not less than 18000 lumens,with pre wired suitable for sports lights complete all as per Cat No.BARFEG 180W LED of make Bajaj or equivalent of make Philips, Wipro, Havells, Syska, Jaguar as approved and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed.

Supply and fix for LED post top latern 40 watts light fitting made of cast aluminium spigot housing with decorative opal acrylic diffuser with IP 65 protection complete with all accessories, fixed on GI pipe medium grade 50mm bore, of suitable height complete all as specified and as directed. Make: Bajaj, Cat Part No.BGCL 40W LED WH, Jaquar Cat Part No. LBLD04R108XW LED or equivalent of make Philips, Wipro, Havells, Crompton, as approved.

S & F for Integral decorative LED bollard with polycarbonate diffuser square shaped with IP 65 protection suitable for 9 watts LED bulb and provision with necessary MS base box made out of MS sheet of 2 mm thick of suitable size abbended in PCC 1:2:4 base, elecrical connections with adequate size complete as all specified and as directed. Make: Bajaj Cat part No BGBOS 600 9W LED, or its equavalent in Philips, Wipro. Note: The contractor shall submit 5 years warranty from date of completion of work.

S&F ceiling fan 1200mm sweep BEE 5 star rated, ISI marked 240 volt AC 50 HZ single phase with hanging rod, conopy set, clamps, bolts nuts and connecting with three core flexible PVC copper conductor cable of size 1.50 sqmm from ceiling rose to fan complete all as specified and directed. Make: Havells Cat No. ES-50 or equivalent of Usha, Orient, Bajaj.

Supply and fix for water heater storage type (Geyser) vertical type with copper inner container of capacity 25 litres, electrically operated, AC 230 Volts including 04 Nos of hold fastener nuts of required suitable size fixed in brick wall including PVC connection pipe (copper) chromium plated 8mm dia both ends threaded with brass coupling bolts both side, cone washer, not less than 45cm long suitable for hot/ cold water system complete all as specified and as directed. Make: Havells Cat part No. GHWASESWH025 or equivalent of Recold/ Bajaj

Supply and fixing of exhaust fan metal body of 230mm sweep, AC single phase, 240 V, heavy duty including metallic louvers and shutter and connecting with three core flexible PVC copper conductor cable of size 1.50 sqmm from ceiling rose to fan including making opening for fixing and making good as per existing as per site requirement complete all as specified and directed. Make: Havells Cat No. Ventil Air- DX White or equivalent of Crompton, Bajaj.

Material and labour for dry sand cushioning in trenches/ ducts for protection of underground cable (below, above and around the UG cable laid in trenches) of 23 cm spread thickness ( 8 cm in depth before laying the cable and 15 cm in depth after laying the cable) and consolidated (punned) up to 18 cm thickness complete all as specified and as directed. Note : - Thickness after punning shall be measured for payment

Material and labour for sub class 'B', old size bricks for cable protection cover, common burnt clay building bricks, laid dry and flat abutting each other with width equal to length of brick and gap between adjacent bricks not exc.10mm complete all as specified and as directed.

Supply and laying for 25mm bore GI tubing light grade laid in trenches as in protection of UG cable at road crossing/ hard standing/ on pole (with necessary MS clamps, nuts, bolts and painting two coats synthetic enamel paint over a coat of red oxide primer) as per site requirement complete all as specified and as directed.

Supply and laying for 40mm bore GI tubing light grade laid in trenches as in protection of UG cable at road crossing/ hard standing/ on pole (with necessary MS clamps, nuts, bolts and painting two coats synthetic enamel paint over a coat of red oxide primer) as per site requirement complete all as specified and as directed.

Supply and fix for 25mm bore steel water tubing 'medium grade' galvanised, with all fittings laid in trenches complete all as specified and as directed.

Supply and fix for gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe 25mm bore, ISI marked complete all as specified and as directed.

Supply and fix for 25mm dia gun metal ISI marked reflux valve (non return valve), ISI marked, flanged and drilled pattern with 2 Nos rubber insertion gasket joints, nuts, bolts & washers of required size & Nos complete all as specified and as directed.

Material and labour for submersible cable with multistranded copper conductor of size 4.0 Sq. mm 3 core 1100 volts PVC insulated weather proof, sheathed heavy duty ISI marked complete all as specified and as directed.

Supply and fix for junction box for street lights, CPRI approved, of size 250 x 300 x 150 mm made out of CRCA sheet 2 mm thick totally enclosed, dust and vermin proof, rain protected slanted roof top, door pasted with rubber gasket, water tight IP 42 protection single leaf shutter in front having proper locking arrangements and painted with powder coating paint and suitable size of "connectwell" stud teriminal (provision for socket bolting)- 05 Nos suitable for 415 volts, 50 Hz, 3 phase 4 wire internal wiring system including MCB SP 06 amps- 01 No and mounted on security light pole with suitable bracket nuts, bolts including taking down of exiting unserviceable box complete all as specified and as directed.

Supply and fix for junction box of size 150 x 150 x 150 mm made out of CRCA sheet 3 mm thick totally enclosed, dust and vermin proof, rain protected having proper locking arrangements and painted with powder coating paint and suitable size of "connectwell" stud teriminal complete all as specified and as directed.

M & L for street light fitting bracket made out of GI pipe 40 mm bore, medium grade 1.50 metre long, bent to required shape and fixing to poles with and including suitable size mild steel clamp made out of flat iron of size 40mm x 6 mm - 02 sets, nuts, bolts as required duly painted with two coats of aluminum paint over a coat of red oxide zinc chrome primer, including taking down existing bracket complete all as specified and as directed.

Supply and fix black bolt with hexagon head and nut round neck of any size as required at site complete all as specified and as directed.

Supply only PVC insulated and PVC sheathed multistranded copper conductor cable of size 4 core 6 Sqmm with necessary electrical connections from fitting to connector block including taking down unserviceable one complete all as specified and as directed. Make: Finolex/ Havells as approved.

Supply, installation, testing and commissioning of 3 phase, AC 415 volt, 50 hz, 5 HP, 2900 RPM submersible water pump set, electric motor driven, having discharge 50 LPM at 40 metres head, suitable for UG sump complete all as specified and directed. Make: Crompton Greaves/ KIRLOSKAR/ Jyothi/ KSB

Supply ,installing, testing and commissioning out door type LT panel board of suitable size, CPRI approved factory made totally enclosed, dust and vermin proof, made of 3.15mm thick CRCA sheet, duly fabricated with door hinged and having proper locking arrangement fixed with MS angle of size 50mm x 50mmx 6mm thick and painted with powder coating paint and comprising with and including following accessories and mounted on PCC plat form of 100mm thick in PCC (1:3:6) type C2 (using 40mm graded broken stone aggregate), 1.0 metre all round the panel complete all as specified and as directed:- (Contd....)

Material and labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less then 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel and connected to main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm with one handle for lifting made out of 8mm dia MS bar, funnel, wire mesh, 20 mm bore galvanized steel tubing (medium grade) for watering, filling charcoal or coke and salt in alternate layers, 15mm bore galvanized steel tubing light grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No.3 of SSR Part-I . (Note: GI earth wire and protection pipe upto 7.5metres shall be deemed to be included in quoted rate)

Material and labour for sub main wiring with approved colour coding as per IS with two runs of single core PVC insulated FRLS cable with multistranded copper conductor of size 6.0 Sq. mm nominal area and drawing through and including non metallic rigid heavy duty PVC conduit white/ ivory and conduit accessories concealed in wall including one run of single core PVC insulated 6.0 Sqmm (nominal area) multistranded FRLS copper conductor as earth wire connected from DB to DB/ main board complete all as specified and as directed. (Note- Two runs of 6.0 Sqmm, one run of 6.0 Sqmm conductor and one run of PVC conduit will be measured as one unit)

Note : 1. Rerformance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site. 3. The site is in scattered area. The building(s)/site(s) shall be handed over in phases and the contractor will have to arrange his working programme accordingly. No claim whatsoever for not giving the entire site on award of work and for giving the site gradually will be admissible, except granting fair and reasonable extension of time.

shrilaxminarayan constructions

m/s Pravin s Bhosale

SHRIYA CONSTRUCTION

M/s Ajinkya Kailas Laigude