8339 REPAIR MAINT TO ROOF FALSE CEILING FLOORING PLUMBING JOINERY ETC AT INDA BLDG MOC NOORBHOY BLDG NCD AND OTHER AREA UNDER AGE BR II UNDER GE NW KUNJALI

Amount

Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc including all necessary scaffolding as required and rubbishing off the premises etc complete all as specified and as directed.

M&L Plastering 15mm thick in CM 1:6 on brick surfaces, finished with Neeru finish on walls complete all as specified and as directed.

M&L Plastering 5mm thick in CM 1:3 on concete surfaces as in ceiling finished even & smooth without using extra cement in ceiling complete all as specified and as directed.

Rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:4 finished even and fair including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified. (Water proofing compound to be measured and paid for separately).

Supply only integral water proofing compound complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets any thickness including cover fillets etc complete all as specified and as directed.

M&L for POP false ceiling using 600X900x12 mm thick plaster of paris with gypsum binder sheet decorative type and necessary provision for concealed type light fittings, fixed on 22 gauge GI channel grid work, main joist of size 50x25 mm spaced at 750 mm centre, secondary joist of size 75X20 mm fixed to main joists spaced at 900mm, suspended to roof members using 25x25x2 mm GI angles and fasteners @ 1.2 M C/C, including dismantling old un serviceable flase ceiling, complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall vertically with screws and C/C deistane 30 CM to make PVC frame as per specification and drawing complete all as directed. (Make Rajshree or equivalent as approved by GE)

S&F PVC wall paneling consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as directed. (Make - Rajshree or equivalent as approved by GE) (Colour of PVC sheet shall be approved by GE)

S&F in repair false ceiling with powder coated exposed GI grid suspension system (E-Grid T-2430 or equvalent load carrying capacity with mid span deflection not exc. 1/360 span with hanger spacing of 1200mm c/c) consisting of main runner 3600mm long, cross Tee 1200mm/600mm long and wall angle. The main runners to be placed @ 1200mm, the cross Tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600mm to form a modular grid of 1200mmX600mm. Additional cross Tees of 600mm shall be placed perpendicular to the cross tee 1200mm long to finally form a grid of 600mmX600mm. Grid of modular size 600mmX600mm shall be supported by 6 mm dia G.I. wire from purlins/soffit with and including 6mm thick high pressure steam cured non asbestos fiber cement designer ceiling board (Density>1200Kg/Cum) of size 595mmX595mm, confirming IS 14862 & Type B Category III of ISO 8336, tested as per AS 1530 part 3 & BS-476 Part 4, 5, 6, 7 & 8, complete all as per manufacturer's instruction. (Make : Armstrong/Chanakya/Everest or equivalent as approved by GE)

S&F 2nd class HW plain fillets clean sawn square, rectangular or triangular in section, sectional area exc 13 but n.exc 25 sqcm fixed with nails all as specified and directed.

S&F for 9 mm thick veneered decorative plywood , grade 1 (with BWR resin) with decorative face veneers on one faces, fixed with screw to timber frame on wall and ceiling etc complete all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles and disposing off complete all as specified and as directed.

M&L brick work with sub class B bricks straight or curved on plan exceeding 6 m mean radius built in CM 1:6 complete all as specified and as directed.

All as per Srl item No 15 here in before but except bricks

M&L stone walling of random rubble, uncoursed brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar 1:4 complete all as specified and as directed.

All as per Srl item No 17 here in before but except stone

M&L for flush pointing in CM 1:3 to random rubble masonry, uncoursed or brought upto courses complete all as specified and as directed.

Taking down chowkats or frames but n exc 1.5 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and as directed.

Taking down chowkats or frames exc 1.5 sqm but n exc 4 sqm each but with shutters (without taking off shutters from the frame) complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sq.m each complete all as specified and as directed.

Taking down shutters of any description n.exc 1.00 Sqm each complete all as specified and as directed.

S&F 2nd class hard wood (SAL) plain, solid, straight chawkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S&F 35mm thick factory made 2nd class HW rail & stile plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

M&L for 2nd class hard wood glazed and skeleton shutters of 35 mm thick , open rebated and prepared to receive glass, gauze, etc. divided in to quares,with plain, chamfered or rounded , mitred and rebated sash bars,any numbers ; edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.20 (a) ; supplied and fitted to chowkhats complete all as specified and as directed.

S&F 40mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both side complete all as specified and as directed.

S&F 30mm thick 2nd class hardwood glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc. divided in to squares,with plain, chamfered or rounded , mitred and rebated sash bars,any numbers ; edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (b) ; supplied and fitted to chowkhats of Second class hard wood complete and as directed.

S&F solid PVC door frame(single rebated) of size 60mmX30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100X8 sheet metal CSK screws complete all as specified and as per as per manufacturers specifiecation and drawings. (Note :- Door frame shall be water proof,termite proof, elegant. and should have excellent screw holding strength to fix hinges and hold doors property for a long life)

S&F 30 mm thick factory made moulded door shutter wood free consisting of frame made out of MS tubes of 19 gauge thickness and size of 20 mm x 40 mm for stiles as well as top, bottom & lock rail. MS frame shall have a coat of metal primer of approved make & manufacturer. The inside panel shall consist of 20 mm thick multichamber hollow PVC section of 1 mm wall thickness, bonded using solvent cement/eynoacrylate adhesive with 5 mm thick moulded PVC sheet of density 600 Kg/Cbm manufactured by an ISO - 9001-2015 certified company with 2, 4, 6 raised panel design in plain/prelam colours after routing the moulded design on one side of the inside panel 5mm plain / prelam PVC sheet to be pasted using solvent cement /eynoacrylate adhesive on other side of the hollow PVC section. All the four edge of the panel to be sealed with lipping of 10 mm thick & 20 mm wide PVC sheet baton (made by sticking 2 Nos foam PVC sheets of 5 mm thickness using PVC solvent cement adhesive. Door edge lipping to be painted with PVC ink of matching colour of plain/prelam moulded PVC sheet of door 20 mm thick (5 mm x 4 Nos) thick PVC sheet to be given for lock provision at lock height . Door to be fixed with frame with 3 Nos stainless steel butt hinges of size 100 mm x 25 mm x 2 mm and 50 mm long steel screws drilled suitable to pass through both the walls of the MS tube other hardwares should be fixed with 20 mm x 8 mm size steel screws etc complete as per direction, manufacturer's specification and drawing.

S&F powder coated aluminium (minimum 25 micron thickness of coating) of various section as required for doors, window & partion/Ventilator etc including fixing and making the frames hinges to receive glass/wire gauge etc. Complete incl all fittings like rubber beading, clips locking arrangement, handle, tower bolt for shutter, sealant etc all as specified and as directed.

S&F aluminium grill with and including suitable aluminium anodised frame F/H section as requird manufactured by M/S Decogrill as per design No DG- 102, 7.5 mm thick all as specified and as directed.

S&F aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel stapple etc. complete all as specified and as directed.

S&F in repairs aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel stapple etc. complete all as specified and as directed.

S&F in repairs 18/19 mm thcik prelaminated partical board exterior grade prelaminated one side with lamination and other side balancing white lamination fixed with screw to frame work cupboard etc including 6 mm thick teak wood beading all around complete all as specified and directed.

All as per Srl item No 36 here in before but 9 mm thick pre-laminated partical board

S&F 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts all as specified.

S&F for aluminium anodized barrel tower bolts 200 mm of extruded section and fixed complete all as specified and as directed.

S&F for aluminium anodized barrel tower bolts 150 mm of extruded section and fixed complete all as specified and as directed.

S&F 150 mm size aluminium alloy handles, febricated type extruded section, ISI marked complete all as specified and as directed.

S&F 100mm size aluminium alloy handles, febricated type extruded section, ISI marked complete all as specified and as directed.

S&F butt hinges 100 mm stainless steel hinges medium weight and fixed complete all as specified and as directed.

S&F butt hinges 100 mm mild steel hinges medium weight and fixed complete all as specified and as directed.

S&F butt hinges 75 mm mild steel hinges medium weight and fixed complete all as specified and as directed.

M & L for MS flat for hold fast. Conforming to Fe-310-0 or Fe-410-0 complete all as specified and as directed.

S&F in repairs 125 mm long floor door stopper of aluminium door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and as directed.

S&F in repairs door closer hydraulically regulated, designation No 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bar; barred iron doors; ladder; framed balusters; walkj ways, railings, frame work for water tanks and similar work conforming to Fe 290 Gd E-165 complete all as specified and as directed.

S&F hand rails, half round or other stock section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars for doors, balusters, nosing to steps including embeding in concrete and screwing etc wind ties for roof incl securing bolts, post and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wires, etc flat iron fillets (for securing wire mesh etc ) incl all necessary drilling bolting or riveting etc and similar work conforming to Fe-290 Gde E-165 all as specified.

M&L for 100 mm thick cement concrete 1:4:8, type D-2 (using 40 mm graded stone agg) as in sub base complete all as specified and as directed.

M&L 100 mm thick cement concrete 1:2:4, type B-1 (using 20 mm graded stone agg) as in hardstanding laid in alternate complete all as specified and as directed.

M&L Factory made cement concrete tiles 25 cm x 25 cm x 22 mm thick, machine pressed chequerd glossy finished of approved colour (with grey cement and pigment), set jointed and pointed in neat cement slurry in floors and cut and polished over & including 15 mm thick bedding layer in cement mortar 1:6 complete all as specified and as directed.

M&L for Factory made machine pressed precast concrete inter locking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness M-35 Grade, glossy finished of approved colour laid over and including 25 mm thick fine sand cushion to a line and slope etc and joined complete including spreading screened river sand over surface for filling the joints with rising surface vibrator etc complete all as specified.

M&L for Factory made machine pressed precast concrete inter locking paver block any shape and size confirming to IS-15658-2006 of 80mm thickness M-40 Grade, glossy finished of approved colour laid over and including 25 mm thick fine sand cushion to a line and slope etc and joined complete including spreading screened river sand over surface for filling the joints with rising surface vibrator etc complete all as specified.

Providing plain cement concrete type B-1, 1:2:4 (using 20 mm graded stone agg) as in lintels upto 1.5 M clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, roof kerbs, water troughs and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L for rolled mild steel section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors ; fixed with angle cleats or other connecting plates conforming to grade Fe 290 (Gde-E-165) incl one shop coat of zinc chromate primer incl preparation of surfaces complete all as specified and as directed.

Dismantling plain or corrugated steel/AC roof sheets any gauge, thickness, including Nainital or similar pattern roof covering all as specified and directed.

S&F in repair pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, chajjas, fixed with self tapping screws as specified.

S&F in repair pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, chajjas, valley gutter, ridge and fixed with crumple joint etc fixed with self tapping screws all as specified and directed.

Dismantling stone slab and tiles of of any description or thickness laid bedded and pointed in any mortar in floors, aprons etccomplete all as specified and as directed.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills,cooking platforms, working table and like over 20 mm thick screed bed or bedding layer in cement mortar (1:4), including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granitecomplete all as specified and as directed.

M &L for machine cut kota stone slab flooring 18 to 20 mm thick as in steps, landings, floors etc laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing,mirror polishing incl making 02 Nos grooves in steps over & incl 20 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M &L for machine cut kota stone slab 18 to 20 mm thick as in skirting/vertical surfaces jointed and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and 15 mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

M&L for roughening surfaces of old concrete surfaces by picking, sweeping cleaning and washing down with water to remove dust etc including taking down tarfelt and 15 mm thick screeding in cement mortar 1:4 finished even and smooth without using extra cement including mixed with water proofing compound as per manufacturer instructions (WPC shall be measured and paid separately).

M&L plain cement concrete 1:2:4, type B-0 (using 12.50 mm graded aggregate) as a leveling course on roof surfaces and coping etc. complete all as specified and as directed.

M&L for applying a coat of oil based bituminous primer @200gm/Sqm on the prepared pastered roof surface, then appy a coat of blown type bitumen grade 85/25 heated to working temprature @1.20Kg/Sqm as per manufacture instructions, manufactured by the same agency of APP membrane. Providing and laying five layered 4 mm thick APP (Atatic poly propylene) modified polyester reinforced water proofing membrane with minimum weight of 4.60 Kg/Sqm as specified here-in-after. The APP membrane shall be laid using LPG torch-on-application with minimum 100 mm side overlap and 150 mm end overlap. The laying of membrane shall be got done through an authorized applicator of manufacturer of the membrane. The APP membrane shall be taken upto minimum 200 mm on vertical surfaces. The edge of the membrane shall be sealed with sealant. The rain water gutter portion shall be finished with cement mortar 1:4 to provde requisite slop towards rain water pipe outlet. Notes :- (i) Irrespective of lap the net covered area shall only be measured and paid (ii) The quoted rate shall be deemed to be inclusive of primer for APP membrane and SBR latex complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding and disposing the rubbish to the out side of MD land complete all as specified and as directed.

S&F 2 mm thick PVC sheets/tiles(flooring) laminated plain cloured, marbled mosaic or mottled finish,laid with approved rubber based adhesive in floors completed.

Dismantling cast iron or reinforced concrete drain pipes of dia upto 100 mm jointed in cement mortar fixed to wall of high rise buildings and taking out from trenches as required.

S&F 100 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls with MS clamps complete all as specified and as directed.

S&F 75 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls with MS clamps complete all as specified and as directed.

S&F 50 mm bore Cast iron soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in floors all as specified and directed.

Fixing only CI pipes 75 to 100 mm bore fixed to wall with MS clamps all as specified and directed all as directed.

S&F in repairs CI Bends100 mm bore (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

S&F in repairs CI Bends 75 mm bore (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

M&L in repairs Cast iron nahani trap with grating including jointing to waste pipe run lead 100 mm complete all as specified and as directed.

Taking down PVC wastage and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc complete all as specified and directed.

S&F 160mm dia bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with MS clamps all as specified and directed.

S&F 160mm dia bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F 75 mmbore PVC (SWR) bends any radius complete all as specified and as directed.

S&F GI tubing medium grade with all fittings like Tee, bend, elbow etc, 15 mm bore fixed to walls or ceilings with saddles/spacers including taking down existing old 15mm bore GI water tubing and connections complete all as specified and directed.

S&F GI tubing medium grade with all fittings like Tee, bend, elbow etc, 20 mm bore fixed to walls or ceilings with saddles/spacers including taking down existing old 20mm bore GI water tubing and connections complete all as specified and directed.

S&F in repairs Vitreous China wash down water closet pan ( pedestal pattern) , white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed.

S&F in repairs, Plastic water closet seat, black or white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed.

S&F in repairs water closet squattin pan (Orissa pattern) 580x440mm, white with integral foot rests including connecting to 'P' trap and to flushing pipe antisyphonage pipe including making good to floor (excluding flushing cistern and flush pipe but including cast iron 'P' trap 100mm dia) complete all as specified and as directed.

S&F in repairs fancy type CP Pillar taps long body 15 mm dia, cast copper alloy, with capstan heads, screwed down high pressure ,with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repairs fancy type bib taps, chromium plated cast copper alloy 15mm bore with crutch or butter fly handle, screwed down, complete all as specified and as directed.

S&F in repairs fancy type angle valve chromium plated cast copper alloy 15mm bore with crutch or butter fly handle complete all as specified and as directed.

S&F in repair wash hand basin vitreous china white (flat back) of size 550x400mm including bracket 15mm dia 32mm dia waste coupling and 32mm dia PVC waste pipe 90cm long etc. complete all as specified and as directed.

S&F PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S&F in repairs PVC valveless syphonic action type ,flushing cistern Low level white, with inlet ball valve, float and handle 10 Ltr capacity including brackets complete all as specified and as directed.

S&F Flush pipe of Polyethylene of low or high density or PVC 32 mm dia. for low level cistern complete all as specified and as directed.

S&F PVC bathroom cabinet with 4mm thick looking mirror of overall size 450 x 300 x 120 mm of approved tint and pattern and drilling in and fixing with 02 Nos. chromium plated screws complete all as specified and as directed.

S&F vitreous china urinal, half stall type white (excluding flushing cistern, flush pipe) but including PVC waste pipe , providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement and fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe. (exclusive of fixing supply pipe to flushing cistern trap and waste pipe) fixed in repair complete all as specified.

Disconnection existing tanks, setting aside (or lowering if required) for cleaning etc and hoisting and reconnecting and re-fixing in the same position capacity exc 250 Ltr and n.exc 500 Ltr complete all as specified and as directed.

Dismantling water tank of capacity exc. 250 Ltrs but n.exc. 500 ltrs.

Dismantling water tank of capacity exc. 500 Ltrs but n.exc. 1000 ltrs.

Dismantling water tank of capacity exc. 1000 Ltrs but n.exc. 2000 ltrs.

S&F in repairs rotational moulded polythylene water storage tank (ISI Marked) of 500 ltr capacity (Cylindrical vertical with closed top) hoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for inron pipe and fixed (minimum weight 210 grms ) all as specified in SSR Part I including taking down exiting old tank complete all as specified and as directed.

S&F in repairs rotational moulded polythylene water storage loft tank (ISI Marked) of 300 ltr capacity hoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for inron pipe and fixed (minimum weight 210 grms ) all as specified in SSR Part Iincluding taking down exiting old tank complete all as specified and as directed.

S&F in repairs rotational moulded polythylene water storage tank (ISI Marked) of 1000 ltr capacity (Cylindrical vertical with closed top) hoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for inron pipe and fixed (minimum weight 210 grms ) all as specified in SSR Part Iincluding taking down exiting old tank complete all as specified and as directed.

S&F in repairs rotational moulded polythylene water storage tank (ISI Marked) of 2000 ltr capacity (Cylindrical vertical with closed top) hoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for inron pipe and fixed (minimum weight 210 grms ) all as specified in SSR Part Iincluding taking down exiting old tank complete all as specified and as directed.

S&F in repairs PVC modular section 20mm thick as in profile including 'C' channels, aluminium all around the profile all as specified.

S&F health faucet ABS Body with 8 mm dia 1 mtr flexible tube and wall hook (Make - Jaquar CAT Part No.-ALD-565 or equivalent as approved by GE)

S&F in repairs aluminium anodised tubular towel rail 20mm dia D type 60 cm long between flanges complete all as specified and as directed. (Make - Jaquar CAT Part No.-ACN-1111SM or equivalent as approved by GE)

S&F counter top wash hand basin incl chromium plated brass waste coupling and PVC waste pipe complete all as specified and directed. Make _ Jaquar CAT Part No.- ALS-WHT-85601 or equivalent as approved by GE

S&F in repairs single piece WC with UF foft close seat cover, hinges, fixing accessories set and accessories set, cistern fittings incl trap/connecting piece complete all as specified and directed. (Make - Jaquar or equivalent as approved by GE)

S&F collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc as specified erected in position and securing runners with holdfasts and brackets complete all as specified and directed.

Removing of bldg materials exc 5 KM and depositing outside of MD land complete all as specified and directed.

Preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of of primer complete all as specified and directed.

M&L for preparation of newly plastered plastered surfaces of ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for preparation of plastered /unplastered surfaces of ceiling surfaces and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying one coat of synthetic enamel paint with necessary scafolding for high rise bldgs etc all as specified and directed.

M&L for preparation of newly steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed.

Complete removal of existing treatment on wall surfaces by scrapping, washing & rubbing down with water and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M&L for preparation of old decorated surfaces of wall and applying one coat of oil emulsion distemper complete all as specified and directed.

M&L for applying 1 to 2 mm thick wall care putty (JK/Birla) for making the surface even & smooth all as specified and directed.

M&L for preparation of old decorated surfaces of ceiling and applying one coat of oil emulsion distemper complete all as specified and directed.

Complete removal of existing treatment on wall surfaces by scrapping, washing & rubbing down with water etc and applying two coats of plastic paint over a coat of primer all as specified and directed.

M&L for preparation of newly plastered surfaces of wall, soffits, facia roof and applying two coats of weather proof acrylic based paint (100% acrylic) over one coat of cement based primer with necesssary scaffolding for high rise blds etc all as specified and directed.

M&L Complete removal of existing treatment of old decorated surfaces of walls soffits, facia roof and applying two coat of weather proof acrylic based paint (100% acrylic) over one coat of cement base primer with necessary scafolding for high rise bldgs. etc all as specified.

M&L preparation of old decorated surfaces of walls, soffits, roof facia and applying one coat of weather proof acrylic based paint (100% acrylic) with necessary scafolding for high rise bldgs etc all as specified and directed.

M&L for preparation of old painted wooden surfaes of any description over 10cm width or girth and applying one coat of synthetic enamel paint including external window with necessary scafolding for high rise bldgs complete all as specified and directed.

M&L for chipping, removing carefully concrete work by low impact hammer breakar without damaging the structure & cleaning and disposal of debries out side the premises etc complete as directed, hard concrete should not be removed by force including necessary scafolding for high rise bldgs etc all as specified and directed.

M&L for clean existing reinforcement with wire/rotary wire brush, making the surfaces free from loose material dirt etc complete applying two coats of alkaline rust converting primer FEOVERT confirming to ASTM-B-117, on the rebars, including cleaning the reinforcement wire brushing to remover loose rust spalls with time interval of 6 hour between the coats and applying protective coating IPNET-RB complete all as specified and directed.

M&L for replacement of steel reinforcement with TMT bars of appropriate size where 20% of cross section is reduced including dismantling of rusted steel including application of rust converter FEOVERT and applying protective coating IPNET-RB complete all as specified and directed

M&L for carry out application of Bi-polar migratory corrosion inhibitor EPCO-KP-100/Protectsil CIT/Ferogard 903 on concrete surface (This inhibitor shall have migratory kind of properly which permits the material to migrate to a vertual extent of 100 mm through pores of concrete, inhibiting the corrosion and de-passivating the Electro-chemical reaction. It should have properly to attack anode as well as cathode, which is purely alkaline in nature (pH-9.5) so it has not carcinogen activity with concrete complete all as specified and directed. .

providing and applying structural grade EPIBOND-21-LP prior to application of any type of mortar plaster confirming to ASTM-C-882-91 (Arizona Slant Shear Test) to ensure bond between old concrete and new concrete complete all as specified and directed.

M&L for Building up the profile of structural members by using latex additives (MONOBOND) modified air cured mortar system (Polymer modified mortar) (1:5:15 = 1 monobond-5Cement-15 sand) -in damaged areas in 30mm thickness including leveling profliling and scaffolding for high rise buildings complete all as specified and directed.

M&L for Providing and applying jacketing around columns/RCC members with Micro concrete (Molith-MC) M40 including all lifts, shuttering, drilling holes and fixing shear anchor as per specification complete.Note: Reinforcement shall be measured and paid separately.(Rates including jacketing, formwork and micro concrete) complete all as specified and directed.

M&L for Drilling and fixing Rohibb Teflon nozzles in RCC members, including drilling holes of 12mm dia, 50 to 100mm deep holes in structural members at the intervals of 500 center to center in staggered manner or as directed by Engr-in-charge in RCC structural element. Work shall be carried out as under :- (i) Cleaning of holes. Clean the holes by air blower prior to fixing nozzles. (ii) Fixing of nozzles. Insert 12mm dia. Rohibb Teflon nozzles in cleaned holes. External end of nozzles to be machine to receive outlet of grouting gun.Fix it inside the holes by applying thixotropic epoxy putty to ensure complete sealing. Cure the system for min.12 hrs. (iii) Cutting of nozzles. Cut the nozzles by chisel after completion of grouting without damaging structural elements.

M&L for Injecting of site cement slurry grout, in the ratio 1:2 (1- Cement, 2-water) including super plsticizer (Supercom-100) 250 ml/50 Kgs. Mixing shall be done by mechanical mixer continuously stirring mechanically to keep cement particles in suspension. Injection of approved/specified grout by means of pump at a pressure of 0.5 Kg/cm2 etc complete till the grout mix flows out from the nozzle indicating complete filling of grout in the holes drilled. (for repair to wall & slab) complete all as specified and directed.

M&L for Injecting low viscosity MONOPOL (3-5cps) high molecular weight monomer by pressure and using mechanized injector gun with accessories till nozzles refuses to accept the grout, Including,Mixing of materials:Mixing of material components(part a&b) in the required quantities as per manufacturer's instruction by weigh batching.Grouting maintain the pressureat exit(0.5 to 1.0 kg/cm2) by monitoring pressure guage at exit.Grout the material through prefixed nozzles in the structural elements@ 100ml per nozzle. Repeat the process for all the nozzles. (Beam and columns) complete all as specified and directed.

S&F 8 mm thick toughned glass ) complete all as specified and directed.

S&F roller/venetian blinds vertical/horizontal type made out of standard cloth of approved texture with necessary accessories etc) complete all as specified and directed.

S&F 4mm thick bakelite sheet with decoratie choice laminated on both side complete all as specified and as directed.

S&F 3 mm thick aluminium composite panel cladding plain of approved colour/shade to beam/column/slab incircular/rectangular shape inbcluding cutting, notching, bending to shape as required jointing with silicon gel of approved colour & aluminum tubular hallow section 25 x 25 mm not exceeding 900 mm C/C on exceeding column/beam/slab to hold APC cladding etc. complete all as specified and as directed.(Note : colour/pattern of ACP sheet shall be given by GE).

MADHU ENTERPRIZES

Sachin santosh dalvi

PRABHU ASSOCIATES

SACHINENTERPRISES

RAJU ENTERPRISES

Genius Construction Co.