PROVN OF TOILET BLOKS AT NIMU MIL STN UNDER AGE(I)NIMU

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out, in hard/dense soil.

Removal of excavated material (soil) to distance exc. 50m but n.exc. 100m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed

Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil, complete all as specified.

Extra over item No. 3 for each additional 1.5m depth or part there of in depth beyound the first 1.5 m depth.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. Or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil, complete all as specified and as directed.

M&L for Plain cement concrete 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) as in foundation filling and mass concrete, complete all as specified and directed by the Engr-in-Charge.

M&L for Precast cement concrete type-C-1 block masonary with solid blocks 1:3:6 (using 20mm graded crushed stone aggregate) exc. 10cm in width and setting in cement mortar (1:6), complete all as specified and directed by Engr-in-Charge.

M&L for 75 mm thick PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in flooring, PCC path, sub base and surface finished even and fair with out using extra cement all as specified and as directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.50 mm graded crushed stone aggregate as in flooring and surface finished rough all as specified and as directed.

M&L for Pressed steel frames size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed

M&L for mild steel work (angle iron or flat iron) as in hold fasts, wall ties, clamps, ventilator pipe, rain water pipe,band, straps, hooks for hanging fans, manhole covers, MS rungs and similar small articles conforming to Fe-310-O or Fe-410-O all as specified and as directed.

M&L for 40 mm thick PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in flooring and sub base all as specified and as directed.

S&F mild steel TMT bars 10 mm dia and over, cut to length , bent to shape required including cranking , bending spirally for hooping for columns, hooking ends, binding with and including mild steel wire ( annealed ) not less than 0.9mm dia , complete all as specified and directed by Engr-in-Charge.

S&F mild steel TMT bars 6 to 8 mm dia and over, cut to length , bent to shape required including cranking , bending spirally for hooping for columns, hooking ends, binding with and including mild steel wire ( annealed ) not less than 0.9mm dia , complete all as specified and directed by Engr-in-Charge.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions

M&L for RCC Design mix, M-25 ( using 20 mm graded crushed stone aggregate ) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete (Note:-TMT bars will be masured and paid sepretly)

M&L for RCC Design mix, M-25 ( using 20 mm graded crushed stone aggregate ) as in Beams, cantilevers, bressummers, lintels over 1.5m span (Note:-TMT bars will be masured and paid sepretly)

M&L for RCC Design mix, M-25 ( using 20 mm graded crushed stone aggregate ) as in Columns, pillars, piers, posts and struts (Note:-TMT bars will be masured and paid sepretly)

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe 410 W (Gde-E-250) quality A.

S&F Mild steel bolts. purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. exc 30cm long dia of neck exc. 12mm but n.exc. 20mm complete all as specified.

M&L for preparation of new surfaces of steel of any description , over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge ..

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L Non skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including laid over screed bed of 15mm thick of cement mortar 1:6 all as specified and directed.

Rendering 10mm thick on fair face of brick work or concrete/stone surfaces in CM 1:6 and finished even and smooth without using extra cement.complete all as specified and directed by Engr-in-Charge.

M&L for 3 coats of white wash on new plastered surfaces of wall including preparation of surfaces all as specified and as directed.

M&L for Glazed ceramic tiles in vertical surface 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with the shade of tiles including laid over backing coat of 10mm thick of cement mortar 1:4 all as specified and directed.

Rendering 15mm thick on fair face of brick work or concrete/stone surfaces in CM 1:4 mixing with WPC @2% by weight of cement or as per manufacturer instruction and finished even and smooth without using extra cement.complete all as specified and directed by Engr-in-Charge. Note:WPC will be measured and paid sepratly.

Supply only water proofing compound.

M&L for preparation of new plastered surfaces and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed by Engr-in-Charge ..

M&L for 2nd class hardwood 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats for doors.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy.

S&F 150mm long aluminium anodised, barrel tower bolts of extruded section

M&L for 2nd class hardwood 30mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. devided in squares in plain, chamfered or rounded. mittered and rebated with sash bars and providing in windows, ventilators and stiles and rails etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (b).

S&F 75mm long butt hinges, medium weight, cold rolled mild steel

S&F 100mm long extruded aluminium alloy handles, fabricated type 'D', anodised

S&F 100mm long aluminium anodised, barrel tower bolts of extruded section

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5 sq. m in each pane

S&F 3mm thick figured glass, pin head type and glazing with oil putty/wooden beading in squares n exc 0.5 sq. m in each pane

M&L for preparation of new wooden surfaces of any description, not otherwise descri-bed, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for hardcore of gauge n exc. 63 mm of broken stone or boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40 mm graded crushed stone aggregate in plinth protection including provision of necessary form work finishing the exposed surface even and smooth complete all as specified.

S & F rotational moulded polythene, two layers, water storage tank 1000Ltrs capacity, closed top, cylindrical, hoisted and fixed in position including minor repairing & 20mm flot ball brass valves high pressure with polythene float and flynut complete, Aluminium rod & high-density plastic ball screwed for iron pipe complete all as specified and dirtected by Engr-in-Charge .

S&F 25mm dia nipple suitable for HDPE water tank. (Minimum weight 25mm- 65gms)

S&F 25mm bore Unions. brass to connect iron to polyethylene

S&F 15mm dia 3-layer PP-R ( Polylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., complete all as specified and directed by Engr-in-Charge.

S&F 20mm dia 3-layer PP-R ( Polylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., complete all as specified and directed by Engr-in-Charge.

S&F 25mm dia 3-layer PP-R ( Polylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc., complete all as specified and directed by Engr-in-Charge.

S&F PP-R Gate valves 25mm dia (brass insert) as per requirement of the site

S&F 25mm ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule

S &F PVC(SWR) pipes single socketed, if any lenth with rubber ring joints, laid in trenches or in floor (75mm bore)

S&F PVC (SWR) floor trap75mm bore, plain with grating including jointing with solvent cement

S &F PVC(SWR) pipes single socketed, if any lenth with rubber ring joints, laid in trenches or in floor (110mm bore)

S &F PVC (SWR) 110 mm dia junction single, (Single T) equal or unequal provided with access door

S&F PVC (SWR) bends redius 110 mm bore

S&F in repair PVC (SWR) vent cowl 110mm in bore complete all as specified and directed by Engr-in-Charge.

S &F PVC(SWR) pipes single socketed, in any lenth with rubber ring joints, (110mm bore) fixed on wall

S &F PVC (SWR) 75 mm dia junction single, (Single T) equal or unequal provided with access door

S&F PVC (SWR) bends redius 75 mm bore

S&F in repair PVC (SWR) vent cowl 75mm in bore complete all as specified and directed by Engr-in-Charge.

S &F PVC(SWR) pipes single socketed, if any lenth with rubber ring joints, (75mm bore) fixed on wall

S&F Vitreous china wash basin, (flat back or angle back type) min size 550 x 400 mm including waste pipe ,32mm dia brass waste fitting, brackets and cutting for and pinning in ends of brackets or errecting stand but excluding taps, chain and plug .

S&F Pillar taps 15mm bore, cast copper alloy, fancy type, with capstorn heeds, chromium plated, screw down high pressure with or without lattered Hot or Cold with long screwed shranks and fly nuts, screwed for iron pipe and fixed

S&F PVC connection 15mm bore of 450mm long

S & F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)Vitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed by Engr-in-Charge.

S&F 40mm dia low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm

S&F stainless steel squatting pan of orissa pattern “long pan”, size 580 x 440 mm standard ivory with ‘P’ or ‘S” trap, front or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe) complete all as specified and directed by Engr-in Charge.

S&F in repair PVC low level valveless, flushing cistern 10 Ltr capacity with inlet , ball valve, float valve and handle & including brackets for fixing to walls and PVC flush pipe of LDPE pipe of pressure rating 6 kg (f)/ sq.cm complete all as specified and directed by Engr-in-Charge.

S&F Bib taps 15mm bore, chromium plated cost copper alloy with crutch or butterfly handle, screwed down screwed for brass ferrule

S&F Stop valve 15mm bore cost copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed bath ends for iron pipe or fixed union

M&L for Granite (of any type) tiles , 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixure of pigment to match the shade of granite stone including cutting and polishing types and laid over 1:4 CM screed bed, complete all as specified & directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, shelves and similar work not exc.200 mm thick (horizontal or slopping) for fair finished flat surfaces all as specified and as directed.

M&L for R.C.C. 1:2:4 type B-1, using 20 mm graded crushed stone aggregates as in slabs,supported on walls, beams and columns in floors, roofs, complete all as specified and as directed.

M&L for 10mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specifications and drawing

M&L for 2nd class softwood Plain fillets. Sectional area exc 13 Sqcm and n.exc 25 Sqcm as in square, rectangular or triangular in section, clean sawn, secured with nails or brads.

Returning filling in including spreading, levelling, watering and well remming in layers not exceeding 25cm thick in hard/dense soil complete all as specified.

Removal of excavated soil to distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed

M&L for 100mm thick PCC 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) as in foundation,sub base, filling & mass concrete all as specified and as directed.

M&L for 75 mm thick PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in flooring/pavment/hard standing and surface finished even and fair with out using extra cement including making impressions of expanded metal while the concrete is green all as specified and as directed.

Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm prmied and sealed with sealing compound, Grade `A' for 100 mm thick slab complete all as specified & directed.

M&L for drilling and tapping cast iron water mains (in position) for branch connections with straight plain brass ferrule of same size for the internal dia 20mm.

M&L for stone masonry walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, bulit in cement mortar 1:4, complete all as specified and directed by Engr-in-Charge.

M&L for stone masonry walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, laid dry, complete all as specified and directed by Engr-in-Charge.

M&L for 100mm thick concrete bed to drain pipe in PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) including packing under and haunching against the sides of pipe after laid and tested for 110 mm bore pipe, complete all as specified and directed by Engr-in-Charge.

M&L for Cement Concrete , 1:2:4, type B1 using 20mm graded agg as in lintel upto 1.50 m span, cills, steps, seismic and other silmilar bands, plinth courses, sring courses,lacing courses, parapets and railings upt 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in item 04028, water troghs and the like including weathering, slightly rounded or camphered angles and throating, complete all as specified and directed by Engr-in-Charge.

Precast reinforced cement concrete, type B-1,1:2:4 (using 20mm graded crushed stone aggreagate)as in manhole cover set in cement mortor 1:4 , complete all as specified and directed by Engr-in-Charge.

Sch "A' Part-II E/M work:- M&L for point wiring with two single core PVC insulated, unsheathed, FRLS type, 1100 volts grade, multistranded copper conductor cable 1.5 sqmm in and including PVC casing caping ISI marked with all connected accessories including one single core multistanded PVC insulated FRLS type, 1.5 sqmm copper conductor cable unsheathed as earth continuity cable including closed recessed wooden terminal boxes of suitable size made of 2nd class hard wood for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet top cover complete all as specified for the following:- Make of cable: Finolex/Polycab/Havells/Plaza. (a) One light /fan/bell point/buzzer point exhaust fan controlled by one nos, one way 5/6 Amps switch.

All as per item No. 86 here-in-before but One 3 pin socket outlet, 5 Amps, independent board, with cables 1.5 sq. mm size

All as per srl item No 86 here-in-before but with conductor of size 4 sqmm (Nominal area) for one 3 pin socket outlet 15 Amps on independent board complete and earth continuity wire with 4 sqmm PVC insulated stranded copper conductor Cable.

S&F Socket outlet multipurpose 2 in 1, 5 pin, 5 Amp flush type

S&F Socket outlet multipurpose 2 in 1, 5 pin, 5 and 15 Amp flush type

S&F Switch piano, flush type single pole, one way 5 Amp

S&F Switch piano, flush type single pole, one way 15 Amp

S&F Ceiling rose 65x50mm, 2 to 3 terminal PVC/polycarbonate, isolated body

S&F LED lights fitting 1x 20W, 4 feet, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F Supply and fixing LED light fitting decorative box type type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F Supply and fixing LED light fitting mirror type type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S&F exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc.

S&F sheet metal powder coated versatile double door SPN distribution board, 8 way suitable for MCB's fitted with copper bus bar rated 200amps, neutral link , earth bar and din rail suitable for use on 240 Volt, 50Hz .

S&F MCB SPN 63 Amp 240 volt AC with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

S&F MCB SP 6-32 Amp 240 volt AC with 10KA breaking capacity of 'C' series in distribution boards all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

M&L for Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to galvanized earth lead wire 4mm dia by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, strip protected by dia 40 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggregate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result complete including taking out of existing earthing all as specified.

Supply, laying and testing LT XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 10 sq. mm 2 core complete all as specified

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth; for laying of cable/pipe & getting out in any type of soil complete all as specified and directed

Returning filling in including spreading, levelling, watering and well remming in layers not exceeding 25cm thick in hard/dense soil complete all as specified.

Removal of excavated material (soil) to distance exc. 50m but n.exc. 100m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed

S&F DWC tubing of size 90/75 mm dia for laid in tranches/along the pole/wall for protection of cable complete all as specified and directed

M/S Web Company