DEVELOPMENT AND BEAUTIFICATION OF SONEGAON LAKE NAGPUR. (PHASE-II)

Amount

Laying and Jointing PVC Pipe. Heading

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. By Mechanical Means (Spec. No. : Bd.A. 1 Page 259/CSR I Page No. 148) i. Lift upto 1.5 m.

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. By Mechanical Means (Spec. No. : Bd.A. 1 Page 259/CSR I Page No. 148) ii. Lift above 1.5 m to 3.00 m.Depth

Transportation of Material obtained from debries of various sorts including necessary excavation / loosing including loading,unloading and conveying and disposing as directed. a) For 1 KM

Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layers including watering and compacting etc. complete.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete.

Providing soling using 80 mm size trap metal in 15 cm. layer including filling voids with Crushed sand/grit, ramming, watering etc. complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.),with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mixcement concrete in M20 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap/ granite/quartzite/gneiss metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M- 25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M- 25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete.

Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete

Providing Second class fly ash brick masonry with conventional / I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of two bars of 6 mm diameter / two hoop iron strips 25 mm x 1.60 mm at every third course, properly bent and bounded at ends scaffolding raking out joints and watering etc. complete.

Providing internal cement plaster 6 mm thick in a single coat in cement mortar 1:4 without neeru finish to concrete surface in all positions including scaffolding and curing etc. complete.

Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete.

Providing internal cement plaster 20mm thick in Single coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc.complete.

Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.

Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622- 2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete.

Providing and laying vitrified matt finish tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622- 2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete.

Providing and fixing heavy duty inter locking concrete Coloured paving blocks of 60 mm thickness of having a strength of 300 Kilogram/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete

Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete.

Providing and applying plastic emulsion paint of approved quality, colour and shade to new surface in three coats including scaffolding, preparing the surface. (excluding primer coat) etc. complete.

Providing and fixing solid core flush door shutter in single leaf 32 mm thick decorative type of exterior grade as per detailed drawings approved face veneers 3 mm thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete.

Providing and fixing steel ventilator fully glazed partly fixed as per detailed drawing with hot dip zinc coating including fabricating glazing with plain / obscured glass pans 5 mm thick and approved type quality and iron oxidized fixtures and fastening with guard square bars 12 mm 10 cm c/c and oil painting 2 coats etc. complete.

Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/Running metre. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 Kilogram/Running metre.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 Kilogram/Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weight o.417 Kilogram/Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With powder coating without box

Providing and fixing M40 grade thick vibrated pull cast or similar type concrete frame with chamfer conforming to I.S. 65241983 having 6 mm dia. bars 3 Nos. And stirrups @250 mm c/c and fixing in wall with 6 Nos of hold fast of 12 mm dia bars 500 mm long including primer and oil painting etc, complete) frame size 60 mm x 100 mm .

Providing and fixing 30mm thick SOLID PANEL PVC INTERNAL DOOR SHUTTER consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 40mm x 20mm for stiles ,top, lock and bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame shall be covered with 5mm thick heat molded PVC channel of size 30 x 100mm forming stiles, and 5mm thick, 125mm wide PVC sheets for top rail, lock rail and bottom rail on either side, and 15mm (5mm x 3) thick, 20mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 10 mm thick prelam PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles and rails with 30mm wide x 5mm thick PVC sheet beading on either side, and joined together with solvent cement adhesive etc. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the C Channel using PVC solvent cement adhesive. including stainless steel fixtures and fastening Complete as per direction of Engineerincharge,manufacturer'sspecification and drawing.

Providing and fixing mild steel grill work for windows, ventilators, etc. 15 Kilogram/Square Metre as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete.

Providing and fixing on walls/ ceiling/ floors, 15 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes weight of 1.48 Kilogram/metre with necessary fittings. remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floors 20 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 1.93 Kilogram/meter with necessary fitting remaking good the demolished portion and applying primer of anti-corrosive oil paint, 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floors, 25 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes weight of 3.01 Kilogram/meter with necessary fittings . remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floors, 32 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes weight of 3.89 Kilogram/meter with necessary fittings . remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing 15 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete.

Providing and fixing screw down 15 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete

Providing and fixing screw down for 20 mm dia. wheeled stop tap of brass including necessary sockets/union nut complete.

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing and laying concrete pipes of I.S.NP. class of 100mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and laying concrete pipes of I.S.NP. class of 225mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.

Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140Kilogramwith frame etc complete.

Providing and fixing 1st class white glazed earthenware Orissa Type W.C. Pan 580 mm dia including P or S trap cast iron soil and vent pipe upto the outside face of the wall (1:5:1 0) cement concrete bedding 15 mm thick, 10 liter P.V.C. flushing cistern with all necessary pipe connection etc. complete.

Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete.

Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters

Providing and fixing 10 cm PVC nahani trap with grating etc. complete.

Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

providing and fixing oval type under counter wash hand basin of 16 inch x 22 inch size and of special colour shade having telephonic black / coloured granite of 180 mm thick stone black kadappa framework including chromium plated coupling bottle - Trap using CERA company or equivalent oval typa wash basin model no 3448 as per detailed drawing or as directed by engg incharge etc complete. (Counter size 1.20 m x 0.60 m )

Providing and fixing European type Colour glazed earthenware water closet pan with UPVC seat and lid with chromium plated brass hinges and rubber buffers including UPVC and vent pipe up to the outside face of wall 10 liter enameled low level flushing cistern with fittings pipe stop tap brackets for fixing cistern 32 mm dia. UPVC flush pipe with fittings and clamps ,20 mm dia.UPVC overflow pipe ,mosquito proof couplings G.I. chain and pulley,with water Jet and fitting including cutting and making good to the walls and floors testing etc. complete.( prior approval of sample and brand by Ex. Engineer is necessary before use)

Providing and fixing in position UPVC ultra violet stabilized 110 mm outer diameter cowl dome confirming to I.S.-4985 including making joints with solvent cement etc. complete

Providing & fixing different design in GFRC as per the detail drawings & sizes with high density concrete made from Portland cement, crushed stone, & polymers reinforced with continuous filament glass fiber mat & jali reinforcing as required. Color to match sample.As per directed by Engineer in charge Walls -stone effects

Providing & fixing different design in GFRC as per the detail drawings & sizes with high density concrete made from Portland cement, crushed stone, & polymers reinforced with continuous filament glass fiber mat & jali reinforcing as required. Color to match sample.As per directed by Engineer in charge Arches & Columns

Excavation for foundation in earth, soils of all types, sand, gravel, soft murum including shoring and strutting, dewatering as necessary and disposing off excavated stuff as directed etc. complete. ( By Mechanical Means ) a) Upto 1.50m lift Normal Rate

Excavation for foundation in earth, soils of all types, sand, gravel, soft murum including shoring and strutting, dewatering as necessary and disposing off excavated stuff as directed etc. complete. ( By Mechanical Means ) b) 1.50m to 3.00m lift, Add 10%

Transportation of Material obtained from debries of various sorts including necessary excavation / loosing including loading,unloading and conveying and disposing as directed. e) For 5 KM

Providing and laying in situ / ready mix / ready mix M10 cement concrete of trap/ granite/ quartzite/ gneiss metal in foundation including necessary centering, formwork, bailing out water, compacting and curing etc. complete. (with fully automatic micro processor based PLC with SCADA enabled with reversible drum type mixer/ concrete batch mix plant (pan mixer) with natural /artifical sand)

Providing and laying in situ / ready mix M-30 controlled reinforced cement concrete of trap metal for raft slab including "V" haunches, formwork, scaffolding, compaction by vibrating, finishing curing etc. complete. concrete batch mix plant / pan mixer with fine agreegates of required specifications ( VSI sand finely washed etc ) etc. complete. (excluding reinforcement). a) RCC Grade with reversible drum type mixer/ concrete batch mix plant (pan mixer) .

Providing and laying in situ / ready mix M-30 cement concrete of trap /granite/quartzite/ gneiss metal for cast in citu R.C.C. solid piers,column etc . including provision of V shaped false joints to form suitable panels on the faces to approve design with compacting by vibrating and curing complete. Including plywood/steel formwork, centering ( excluding dewatering by means of pump) and including bailling out water and including CM 1:3 curing complete. a) Height upto 5 M. (With Concrete Mixer)

Providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2 coats of oil painting approved quality and shade etc. complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M- 10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing, fixing and installation of decorative type Gate in cast iron and MS pipes of Required height consist of MS pipes, CI flat leafs etc as per detailed drawing and specification provided by architect & engineer in charge, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Providing, fixing and installation of decorative type grillwork in cast iron and MS pipes of height 1.5m to 2.0m consist of MS pipes, CI flat leafs etc as per detailed drawing and specification provided by architect & engineer in charge, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.

Providing and fixing Country cut teak wood double or single leaf panelled shutters, 35 mm thick style top and freze rail 95 x 35 thick with lock and bottam rail 195 x 25 mm thick and panels without ventilator as per detailed drawing excluding the door frame, stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats complete

Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete

Providing and laying Cast in situ/Ready Mixcement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M- 25 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M- 25 of trap /granite / gneiss/ quartzite metal for R.C.C. arches with skew backs as per detailed design and drawings or as directed including steel centering, plywood/steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement, including cover block). Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed) With fine aggregate (Crushed sand VSI Grade)

Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 Square Metre /Kilogram with two coat using approved chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete.

Providing and laying cement concrete flooring 50mm thick with M20 cement concrete laid to proper level and slope in alternate bays including compaction, filling joints, marking lines to give the appearance of tiles of 30cm x 30cm or other size laid diagonally/ square etc. finishing smooth (with extra cement) in any colour as directed and curing etc. complete.with Crushed sand VSI Grade

Providing and fixing in position anodised (as per IS 1868/1982) Aluminium fixed staggered ( Z Type) Ventilator with aluminium rectangular pipe 63 mm x 38.10 mm x 1.22 mm at weight 0.650 Kilogram/Running metre, Aluminium angle of size 15 mm x 15 mm x 1 mm,aluminium channel of 9 mm sizes, S.S.mosquito net of 304 Grade,4 mm thick float glass per detailed drawing and as directed by Engineer in charge etc.complete.

Providing and laying in trenches 50 mm dia. medium grade having embossed as ISI Mark galvanised iron pipes ?of 5.17 Kilogram/meter necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing push cock (Self closing tap) symet type of 15 mm dia. including necessary socket, testing etc. complete.

Providing and fixing White Glazed Earthenware full stall type Urinal with P.V.C. flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 mm dia. P.V.C flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connectionup to the outside face of the wall

Providing and installing bio digester unit based on DRDO technology made of fibre reinforced plastic (FRP) having composition and following technical specifications and including necessary pipe and accessories up to 3 meter length, excluding the necessary excavation for installing the bio digester. Percentage of fibre glass (glass content in fibre glass should be minimum 30%): -33.33% Percentage of polyester resin: - 66.67% Water absorption (as per ASTM):-0.30% Flammability as per ASTM Tensile strength:-115 MPA Specific Gravity at 25 degree centigrade 1.45 Izod impact strength:-65KJ/M2 Heat defection/distort temperature:-65deg C Corrosion resistance (Non Corrosive) fitted with Inlet pipe size rigid PVC: -100mm Outlet pipe size rigid PVC:-80mm Gas outlet rigid PVC with Valve: 20mm Bacteria immobilization PVC mattes (on all partition) With DRDO TOT licensee and latest batch certificate(month & year of supply) and capacity as below f) Up to 80 user size (2.7mx1.5mx1m), Capacity of Biodigester:-4000 liters, Area of top, bottom and side walls: - 16.50 sq.m, Area of partition walls: 4.50sq.m, Total weight of FRP: - 202.50 Kilogram, Bacteria inoculums quantity: - 1400 liters, Minimum thickness of side walls / top and bottom: 6mm, One Number of inside partitions: - 4, Minimum thickness of partition wall: 3mm

Providing structural steel work in hollow section of various thickness and sizes in square, rectanular and round shape from 25mm to 450mm section as per IS 4923 YST 310 Grade produced from iron ore and blast furnace route etc. as per detailed designs and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, making riveted/bolted/ welded connections and painting complete.

Providing and laying Polished Shahabad Stone flooring 25mm to 30mm thick and required width wide in plain/ diamond pattern on a bed of 1:6 C.M. including cement float, filling joints, with neat cement slurry, curing, polishing and cleaning etc. complete.

Dismantling stone masonry in lime or cement mortar including stacking the materils as directed with all leads, lifts etc.

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 5.0 to 9.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary)

Providing cast in situ / ready mix M20 grade cement concrete for head walls of CD work / retaining walls etc. including necessary form work, compaction, finishing and curing etc. complete. (with reversible drum type mixer/ concrete batch mix plant (pan mixer) with SCADA

Providing coursed rubble masonry first sort of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in superstructure including racking out joints on the inside when plastering is to be done, watering and scaffolding etc. complete.

Providing and fixing stone cladding in required thickness (115 to 150mm) in sandstone / basalt stone in alternate layer as per drawing to RCC wall,column brick walls, etc in ashlar finish including cost of stone, fixing in cement mortor in 1:3 (1 cement : 3 sand), synthetic adhesive, pointing with white cement mortor 1:2 (1white cement : 2 matching colour stone dust ) with an admixture of pigment matching the stone shade including dressing of stone, drilling holes, making chassis, metal cleats clamps, hoisting, fixing, finishing, cleaning, scaffolding & curing all complete as instructed and to the satisfaction of the architect/Engineer in charge.

Providing and fixing Sand Stone/ Black Stone of approved quality vein & colour for Cladding/Moulding to 230 mm thick solid sand /black stone on the size of cladding/Moulding stone should be as per profile on Parapet Wall as shown in detailed drawing. The top surface of cladding/ Moulding should be carved & moulded as shown in drawing. As per drawing approved by Engineer in-charge / Architect. Including cutting, dressing, machine / hand polish to surface, embossing, carving, grooving, mural work, installation and grinding, scaffolding, hoisting, erecting, fixing by mechanical jointing along with approved adhesive (like Adeldite), cement slurry and making level surface by cement mortar 1:4 before fixing, transportation of all materials up to site of work, approved water proofing treatment, filling of joints, cleaning, applying Anti-Moss treatment on surfaces of stone with specified chemical approved by Engineer in-charge including all material, labour, lead and lift etc.. complete

Providing and laying weep holes of 100 mm diameter PVC pipes as per drawing for abutment returns, return walls etc. Complete.

Providing tuck pointing with cement mortar 1:3 for stone/Brick masonry including scaffolding and curing etc. complete.

Providng Grouting by specially prepared grout of approved make chemical with cement in proportion 1:3.5 (1 part chemical & 3.5 part cement by weight) along wih 50 ml super plasticizer non cracking antiwash high strength polymer cement grout P C grout available in bags or equivalent with proper water for injectable consistency and applying it in the body of structure like slab, beam, column, pillars, deckslab, retaining wall, basement, underground and elevated water storage reservoir concrete and brick wall, crack portion of structure etc. by injectng method, to achieve its original strength including drilling of suitable diameter drills holes at 2 to 4 Nos. per sqm. using caps and nozzle grouting machinery necessary, scaffolding, finishing and covering gurantee of 10 years on court stamp paper of Rs. 100/- and necessary testing etc. complete. (Prior permission of S.E. in writing is necessary before inclusion of this item in estimate)

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.

Supplying, Drilling/Cleaning hole and injecting chemical. Application to be designed separately for Rebars as Simply Supported, Moment or Splice Connection as per EC2/TR 023 or relevant tested and accepted rebar guidelines. The chemical should have ETA approval for seismic rebar as a minimum qualifying criterion. Drilling hole with double flute type drill bits or hollow drill bits to the required depth by rotary hammer drill, cleaning with brush and jet of clean air, filling resin and hardener using serrated nozzle to eliminate mixing error with standard HDE A22 battery dispenser along with piston plug. The installation and the setting instructions should be strictly followed as per the manufacturer’s recommendations. The adequate diameter and embedment of rebars to be decided as per PROFIS Rebar Software & the report to be submitted to the project manager/ design engineer for approval. Scanning before drilling to be done to avoid hitting existing rebars. Re 500 -10 mm dia 200mm depth

Providing and fixing on walls/ ceiling/ floors, 100 mm dia.heavy grade having embossed as ISI Mark galvanised iron pipes weight of 14.74 Kilogram/meter with necessary fittings. and remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 600mm diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.

Providing internal cement plaster 20mm. thick in Single coats in cement mortar 1:3 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete.

Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness or Tape Grooves 35 to 45 mm thickness or as required, in all position including preparing the surface, scaffolding etc. complete.

Providing and applying two coats of textured synthetic paint of approved shade and quality and one coat of primer before applying textured paint including scaffolding if necessary preparing surface by thoroughly cleaning oil, grease, dirt and other materials as required, etc. complete.

Providing and fixing bituminous pad 25mm thick for expansion joints in retaining wall, compound wall etc. complete.

Supplying hard murum/ kankar at the road site, including conveying and stacking complete.

Spreading hard murum/ soft murrum/ gravel or kankar for side width complete

Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering etc. complete.

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader / Paver on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- By Mix in Place Method and Grading - I Material a) Spreading with motor grader / Paver

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader / Paver on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- By Mix in Place Method and Grading - II Material a)Spreading with motor grader / Paver

Construction of dry lean cement concrete Sub- base over a prepared sub- grade with coarse and fine aggregate ( VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, , cement content not to be less than 150 Kilogram/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge , compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etc. complete.

Stamp Concrete of 100mm Thickness - Providing and Laying in-situ M30 Grade unreinforced plain cement stamp concrete of 100mm thickness pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate (natural sand / VSI grade finely washed crushed sand) Confirming to IS 383, as per mixed in a batching and mixing plant / non tilting mixer and weigh batcher as per approved mix design, admixtures, transporting to site in nagpur city with lead upto 20KM (on Inner Ring Road from Avasti nagar to wadi), spreading, laying with approved make pover, compacted and finished in a continous operation, finishing to lines and grades Also Providing, Placing and applying stamp powder which is light fast UV resistant pigment with appropriate chemical compounds of desired colour on base concrete after excess bleed water has evaporated using dry shake method @5kg per sqm. Including texturing, and covering with plastic sheet (min 200 micron thickness) and also applying two coats of UV-stable,30 % solids clear sealer @ 150 to 250 gms per sqm using surface roller and protecting from falling dust,dirt and curring by curring compound / by providing cement vata in cement Mortor 1 :8 @ 0.6m x 0.6m center to center, admeasuring 80mm at bottom and 40mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-incharge or Landscape architect etc. complete. (prior approval of superinteding Engineer will be necessary )

Cutting transverse contraction joints 3 to 4 mm wide and depth 60mm. .in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay / slab etc. complete including subsequent widening of the groove 8 to 10 mm. wide at top having depth of 15 mm. as directed by Engineer incharge.

Providing to contraction joints polysuphide sealent (Pouring grade) confirming to BS : 5212 - 1989 into sawed groove widened at top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter (appraox. 25% larger than the initial 3 mm.to 4 mm. joint) overlaid with bond breaking tape as per detailed drawing. Item includes cleaning the joints with water jet / air compressor and allowing joint to become thoroughly dry before sealent is applied and applying primer. (A) Contraction and longitudinal joints (15 mm. deep x 8 mm.wide)

Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to IS 3395 : 1997 below concrete pavement including all materials and labour complete.

Providing and fixing of retro- reflectorised informatory sign board rectangular/Square in shape having area greater than 0.9 square meter made out of mm aluminum sheet bonded with white retro reflective sheeting of Class ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3, supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with two coats of grey stove enamel paint and supported on two Number mild steel angle iron post 75 mm x 75 mm x 6 mm, 3.5 mt long firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing The angle iron post shall be duly painted with one coat of epoxy primer and two coats of epoxy finish paints having alternate black and white bands of 25 cm width including GI fixures and transportation etc.complete.The nut bolts of board with angle iron post/supporting structure after fixing at site has to be electrically welded. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) sheeting shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty a) 2mm aluminum sheet Class B

Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed.

Providing and fixing precast tapering kerbs of M-20 (Single tapered divider) as per the detailed drawing filling in joint by cement Mortar 1:2 Cement pointing and curing, including excavation upto depth of 0.25m,PCC-M10 is upto 0.12m and painting exposed faces with one coat of road marking paint of approved col 1) 300 X 150 X 450 mm

Providing and laying in situ / ready mix controlled grade of M20 of trap /granite /quartzite /gneiss metal for RCC works in cut off walls / curtain walls including necessary scaffolding, centering, compacting by vibrator, finishing and curing etc. complete. (with fully automatic micro processor based PLC with SCADA enabled with reversible drum type mixer/ concrete batch mix plant (pan mixer) with fine agreegates of required specifications ( VSI sand finely washed etc ), excluding reinforcement)

Providing and fixing Natural stone pavers / cobbles from Black Gaboriau granite / sand stone available in colours like black, gray, green, yellow of approved mines Available in hand cut 8" x 4" / 4" x4" with thickness 65 mm to 75 mm including cost of all materials, manufacturing ,curing transportation of block to work site , loading, laying paving stone blocks in position and fixing it in required position on a prepared bed of C.M. 1:6 , 35mm to 50 mm thick or fly ash morter bed of 35mm to 50 mm thick including ramming rolling and levelling to desired slope, filling joints with neat cement slurry curring and cleaning etc. complete (Prior permission of S.E.in writing is necessary before inclusion of this item in estimate). complete.

Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight C. I. cover of 75Kilogramwith lid and frame fixed in cement concrete.

Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and C.I. lid cover of 75Kilogramwith lid and frame fixed in cement concrete.

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with vibratory roller to the required density. By Mechanical Means - Grading I (Using Screening Type B (11.2 mm) Aggregate)

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with vibratory roller to the required density. By Mechanical Means - Grading II (Using Screening Type B (11.2 mm) Aggregate)

Providing and fixing in position HDPE pipe (90 mm dia) of specified OD, grade pe -63, including necessary fittings such as bore nipples , tees, flanges reducers, clamps, plugs etc. including necessary excavation trench filling, necessary drilling holes in walls, slab etc. and making good the surface complete.(for 6 kglsq.cm pressure) (prior approval of sample and brand by ex. engineer is necessary before use

Providing and fixing in position HDPE pipe (75 mm dia) of specified OD, grade pe -63, including necessary fittings such as bore nipples , tees, flanges reducers, clamps, plugs etc. including necessary excavation trench filling, necessary drilling holes in walls, slab etc. and making good the surface complete.(for 6 kglsq.cm pressure) (prior approval of sample and brand by ex. engineer is necessary before use )

Providing and fixing pop up sprinkler 32 mm dia. inlet having 13 to 18 meters radius including necessary swing joint, sockets, saddles, riser pipe, union nut, testing etc. complete. (prior approval of sample and brand by ex. engineer is necessary before use.)

Providing and fixing gate valve of brass 2 1/2" (65 mm) as specified dia. Including necessary sockets, flanges, nipples, union nut testing etc. complete. (prior approval of sample and brand by ex. engineer is necessary before use.)

Providing and fixing quick coupling valve 3l4"of brass including necessary Sockets, swivel hose pipe 3/4" - 30 meters length, swivel elbow, opener key, g i tees, flanges, union nut, testing etc. complete. (prior approval of sample and brand by ex. engineer is necessary before use)

Providing and fixing rectangular / round valve box of hdpe / pe material 12 " with green top opening cover, testing etc. complete. (prior approval of sample and brand by ex engineer is necessary before use.)

Providing and fixing rectangular / round valve box of hdpe / pe material 10 " with green top opening cover, testing etc. complete. (prior approval of sample and brand by 4. ex engineer is necessary before use.)

Providing and fixing Drip Irrigation System of Tube diameter -16mm, the number of meter in the Bay From (100 to 500) length of Bay is 30m, drip emitters- compensated PC & uncompensated ( No PC), Consumption- 1 liter/hr, 1.6 liter/hr, 2 liter/hr, 4 liter/hr & 8 liter/hr, Dipper distance from 200-2000mm the wall thickness 0.7mm to 1 mm, operating pressure 1 to 4 bar, the material resistance to UV & temperature changes including all labour, material & fixing etc. compled

Yield Testing of borewells using90" 'V' Notch by air lift method for two hours for successful borewell as per yielidng Borewell and installation. Yield testing of Borewell using 80"V'

Driling of 150mm diameter Inwell vertical bore including removing the excavated material upto a distance of 50 metres, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete.

Providing casing pipe welded threaded joints medium class ERW Mild Steel block as per ISI 1239 specifications with socket and inserting in Tube well through over burden including transportation to site cutting threading & grouting the sand with cement slurry including in the cost of the coupling and plugs of 4.8mm thick etc. complete 150mm dia perforated. providing casing pipe welded threaded joints.

Providing and laying in trenches 80 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 10.15 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing , Laying and lowering double flange sluice valve confirming for IS-2906/14846 including worn gear arrangements as per test pressure stainless steel spindle,caps including all taxes transportation etc.complete.80mm Sluice Valve PN-1 without bye pass arangement

Providing and supplying ISI mark CI D/F reflux valves (non-return valves) of following dia.including all taxes (Central and Local),railway freight,inspection charges unloading from railway wagon,loading into truck,transportation upto departmental stores/site, unloading, stacking etc.complete.reflux valves as per I.S.5312 Part I(1984) iii) 80mm

Supplying on site fresh Garden soil (free from stones rubbish like dried grass roots, other such materials) for excavation area of depth of 20 cms.( consolidated thickness).(As per P&G DSR 2022-23 Items of garden work,Sr No.38a)

Supplying on site well decomposed Farm Yard Manure for excavation area of depth of 20 cms. ( consolidated thickness).(As per P&G DSR 2022-23 Items of garden work,Sr No.38b)

Providing on site well established (free from weeds /diesease etc.) ready to fix lawn turf in slabs/ rolls of required variety as directed .(As per P&G DSR 2022-23 Items of garden work,Sr No.14, item no 2)

Providing on site required variety of Shrubs (free from weeds /diesease etc.) 30 cms. apart c/c.Name:-Murraya(Kamini);Bag Size 7'' x 8" (plants list) 1(a) serial no 15.

Providing on site required variety of Hedges Well Developed, Healthy Foliage / Half Bloom Stage , Free from Pest and Diseases. apart c/c.Name:-Bougavillae Thema ;Bag Size 8'' x 10" (plants list) 7(b) serial no 10.

Excavation for planting lawn/ shrub/ flower bed/ hedges/ edges/ canna bed in earth, soil of all types, soft murum, including removing the excavated material up to a distance of 50 mtrs. for a depth of 20 cms.(As per P&G DSR 2022- 23 Items of garden work,Sr No.5)

Mixing garden soil/silt & manure thoroughly well, watering previous night. Planting reqired plant species, lawn grass as directed etc. complete for required depth 20 cms. for planting lawn/ shrub/ flower bed/ hedges/ edges/ canna bed/ ground cover. (1/10 of semiskilled labour)(As per P&G DSR 2022-23 Items of garden work,Sr No.23)

Maintainance of Newly Developed lawn(Instant Lawn) Area. For First 30 days Only (As per P&G DSR 2022-23 Items of garden work,Sr No.29)

Maintainance of Newly Developed Shrubs Area. For First 30 days Only (As per P&G DSR 2022-23 Items of garden work,Sr No.31)

Supplying on site fresh Garden soil (i. e. 3 part soil ) (free from stones rubbish like dried grass roots, other such materials) for excavated pit size area of 1 x 1 x 1m ( consolidated thickness).Quantity of soil 0.653 cum x 800/cum = 522.40/-.(As per P&G DSR 2022-23 Items of garden work,Sr No.45a)

Supplying on site fresh Garden soil (i. e. 3 part soil ) (free from stones rubbish like dried grass roots, other such materials) for excavated pit size area of 0.45 x 0.45 x 0.45m ( consolidated thickness).Quantity of soil 0.079 cum x 800/cum = 63.20/-.(As per P&G DSR 2022-23 Items of garden work,Sr No.43a)

Supplying on site well decomposed Farm Yard Manure FYM (i. e. 1 part FYM) for excavated pit size area of 0.45 x 0.45 x 0.45m. ( consolidated thickness).Quantity of FYM 0.203 cum x 950/cum = 21.85/-.(As per P&G DSR 2022-23 Items of garden work,Sr No.45b)

Providing on site Flowering Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-HAMELIA PATENS ;Bag Size 8 x10'', ht 45- 60CM (plants list sr no1 ( b) , item no 6 Page no -16)

Providing on site Flowering Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-hibiscus ;Bag Size 8 x10'', ht 45- 60CM (plants list sr no1 ( b) , item no 7 Page no -16)

Providing on site Flowering Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-IXORA MINI ;Bag Size 8 x10'', ht 45- 60CM (plants list sr no1 ( b) , item no 8 Page no -16)

Providing on site Flowering Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Jatropha ;Bag Size 8 x10'', ht 45- 60CM (plants list sr no1 ( b) , item no 12 Page no -16)

Providing on site Flowering Shrubs Specification:-Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Mogara/Jasminum ;Bag Size 9 x11'', ht 20- 45 CM (plants list sr no1 ( b) , item no 14 Page no -16)

Providing on site Flowering Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Murraya/ Kamini ;Bag Size 9 x11'', ht 20- 45 CM (plants list sr no1 ( b) , item no 15 Page no -16)

Providing on site Flowering Shrubs Specification:-Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Ratrani/ Night queen ;Bag Size 8 x 10'', ht 45- 60 CM (plants list sr no1 ( b) , item no 19 Page no -16)

Providing on site Flowering Shrubs Specification:-Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Russelia ;Bag Size 8 x 10'', ht 30- 45 CM (plants list sr no1 ( b) , item no 23 Page no -16)

Providing on site Flowering Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Tagar Variegated ;Bag Size 10 x 10'', ht 30- 65 CM (plants list sr no1 ( b) , item no 25 Page no -17)

Providing on site Flowering Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Tecoma capensis ;Bag Size 10 x 10'', ht 30- 65 CM (plants list sr no1 ( b) , item no 26 Page no -17)

Providing on site Flowering Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Tecoma capensis ;Bag Size 10 x 10'', ht 30- 65 CM (plants list sr no1 ( b) , item no 26 Page no -17)

Providing on site Foliage Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Alpinia ;Bag Size 13 x 13'', ht 30- 60 CM (plants list sr no 2 ( b) , item no 2 Page no -18)

Providing on site Foliage Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Aralia ;Bag Size 13 x 13'', ht 30- 60 CM (plants list sr no2 ( b) , item no 3 Page no -18)

Providing on site Foliage Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Cordyline ;Bag Size 13 x 13'', ht 30- 60 CM (plants list sr no2 ( b) , item no 5 Page no -18)

Providing on site Foliage Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Cyperus Golden ;Bag Size 18 x 18'', ht 90- 120 CM (plants list sr no2 ( b) , item no 8 Page no -18)

Providing on site Foliage Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Diffenbachia ;Bag Size 13 x 13'', ht 45- 60 CM (plants list sr no2 ( b) , item no 10 Page no -18)

Providing on site Foliage Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Facus Golden ;Bag Size 13 x 13'', ht 45- 60 CM (plants list sr no2 ( b) , item no 15 Page no -19)

Providing on site Foliage Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Facus Safari ;Bag Size 13 x 13'', ht 45- 60 CM (plants list sr no2 ( b) , item no 18 Page no -19)

Providing on site Foliage Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Mayurpankhi/ Thuja ;Bag Size 13 x 13'', ht 45- 60 CM (plants list sr no2 ( b) , item no 21 Page no -19)

Providing on site Foliage Shrubs Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Pisonia alba ;Bag Size 10 x 10'', ht 30- 45 CM (plants list sr no2 ( b) , item no 22 Page no -19)

Providing on site Flowering Climbers and creepers Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Allamanda (allamanda cathertica) ;Bag Size 7 x 8'', ht 15- 30 CM (plants list sr no 3 , item no 2 Page no -19)

Providing on site Flowering Climbers and creepers Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Kunda ( Jasminum Multiflorum) ;Bag Size 7 x 8'', ht 15- 30 CM (plants list sr no 3 , item no 6 Page no -19)

Providing on site Flowering Climbers and creepers Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Jui ( Jasminum officinale) ;Bag Size 7 x 8'', ht 15- 30 CM (plants list sr no 3 , item no 7 Page no -19)

Providing on site Flowering Climbers and creepers Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Passionflower (Passiflora blue) ;Bag Size 7 x 8'', ht 15- 30 CM (plants list sr no 3 , item no 9 Page no -19)

Providing on siteBalbous / Rhizomatous plants Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Dahlia ;Bag Size 7 x 8'', ht 30- 45 CM (plants list sr no 4 , item no 4 Page no -20)

Providing on siteBalbous / Rhizomatous plants Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Lilium sp. ;Bag Size 7 x 8'', ht 30- 45 CM (plants list sr no 4 , item no 6 Page no -20)

Providing on siteBalbous / Rhizomatous plants Specification:- Well Developed, Fresh, Healthy half in bloom, Free from pest and disease Name:-Chrysanthemum ;Bag Size 7 x 8'', ht 30- 45 CM (plants list sr no 4 , item no 10 Page no -20)

Providing on site Flowering Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged. Apart c/c.Name:-Bahva (Amaltash);Bag Size 18 x18'', ht 8- 10'(plants list sr no 5C, item no 1 Page no -22)

Providing on site Flowering Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged. Apart c/c.Name:-Bakul ;Bag Size 18 x18'', ht 8- 10'(plants list sr no 5C, item no 2 Page no -22)

Providing on site Flowering Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged. Apart c/c.Name:-Gulmohar ;Bag Size 18 x18'', ht 8- 10'(plants list sr no 5C, item no 4 Page no -22)

Providing on site Flowering Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged. Apart c/c.Name:-Kadamb;Bag Size 18 x18'', ht 8- 10'(plants list sr no 5C, item no 5 Page no -22)

Providing on site Flowering Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged. Apart c/c.Name:-Kanchan;Bag Size 18 x18'', ht 8- 10'(plants list sr no 5C, item no 6 Page no -22)

Providing on site Flowering Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged. Apart c/c.Name:-Largesstroemea ;Bag Size 18 x18'', ht 8- 10'(plants list sr no 5C, item no 7 Page no -22)

Providing on site Flowering Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged. Apart c/c.Name:-RAIN TREE ;Bag Size 18 x18'', ht 8- 10'(plants list sr no 5C, item no 9 Page no -22)

Providing on site Flowering Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged. Apart c/c.Name:-SHITA ASHOK ;Bag Size 18 x18'', ht 8- 10'(plants list sr no 5C, item no 10 Page no -22)

Providing on site Flowering Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged. Apart c/c.Name:-SPATHODIA ;Bag Size 18 x18'', ht 8- 10'(plants list sr no 5C, item no 12 Page no -22)

Providing on site Flowering Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged. Apart c/c.Name:-Nilmohar ;Bag Size 18 x18'', ht 8- 10'(plants list sr no 5C, item no 8 Page no -22)

Providing on site Foliage Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged.. Apart c/c.Name:-Arjuna ;Bag Size 18 x18'', ht 8- 10'(plants list sr no 6C, item no 3 Page no -24)

Providing on site Foliage Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged.. Apart c/c.Name:-Deshi Badam ;Bag Size 18 x18'', ht 8- 10'(plants list sr no 6C, item no 4 Page no -24)

Providing on site Foliage Trees Specification:- Minimum Girth 8 to 10 c.m. Minimum 5 to 6 Branches with Maximum number of Leaves ,clear trunk, well Developed Canopy,Healthy conditionFree from pest and diseases,well seteled in appropriate size of Plybag,uniform in size and root system are undamaged.. Apart c/c.Name:-Drooping Ashok ;Bag Size 18 x18'', ht 8- 10'(plants list sr no 6C, item no 5 Page no -24)

Providing on site HEDGES Specification:- Well developed, healthy Foliage/ Half bloom stage, free from pest and diseases .Name:-Bougavillae Thema ;Bag Size 18 x18'', ht 60cm to 75 cm (plants list sr no 7d, item no 2 Page no -26)

Providing on site HEDGES Specification:- Well developed, healthy Foliage/ Half bloom stage, free from pest and diseases .Name:-Bougavillae Glabra;Bag Size 13 x13'', ht 60cm to 75 cm (plants list sr no 7d, item no 3 Page no -26)

Providing on site Ground Cover Specification:- Well developed, healthy, free from pest and diseases .Name:-Asparagus ;Bag Size 7 x8'', ht 10cm to 20 cm (plants list sr no 8, item no 3 Page no -26)

Providing on site Palms Specification:- Palm should be well Developed,Good Branching ,healthy Condition,appropriate Size in Polybag,undamaged. .. Apart c/c.Name:-Areca Palm ;Bag Size 18 x18'', ht 8- 10'(plants list sr no1,item no 11d)

Providing on site Palms Specification:- Palm should be well Developed,Good Branching ,healthy Condition,appropriate Size in Polybag,undamaged. .. Apart c/c.Name:-Fox tail palm;Bag Size 18 x18'', ht 8- 10'(plants list sr no3,item no 11d)

Providing and Supplying Cement Pot size 36 Inch x 18 inch x 18 Inch of good quality, Durable well finish on edge with good strength

Excavation pit size 1.00 x1.00 x 1.00m for planting large flowering/ shady trees (plant height 2 to 4 mtr.)/ palm varieties of height (plant height 2 to 4 mtr.) in earth, soil of all types, soft murum, including removing the excavated & unwanted material up to a required distance of 50 mtrs. (As per P&G DSR 2022-23 Items of garden work,Sr No.12)

Excavation pit size 0.45 x 0.45 x 0.45 m for planting earth, soil of all types, soft murum, including removing the excavated & unwanted material up to a required distance of 50 mtrs. (As per P&G DSR 2022-23 Items of garden work,Sr No.10)

Mixing garden soil/silt & manure thoroughly well, watering previous night. Planting reqired plant species as directed etc. complete for required pit size 1.00 x 1.00 x 1.00m.(1/10 of semiskilled labour)(As per P&G DSR 2022-23 Items of garden work,Sr No.27)

Maintainance of Newly Planted tree varities having height 2mtr. - 4mtr. For First 30 days Only (As per P&G DSR 2022-23 Items of garden work,Srs No.35)

Providing and filling in the foundation with sand of approved quality including watering, compacting etc. complete. (To be executed with prior approval of Superintending Engineer)

Spiral Slide:- Providing and fabricating and erecting spiral slide with ISI mark G.I. Pipe the assembly constitutes of the following. (a) The sliding chute shall be made up of fiber reinforced plastic (FRP) type moulded one and shall be painted with attractive colours and shade, minimum joints shall be provided for FRP spiral slide. The design of spiral is such that the children would not fall down while sliding in rotation towards down slide. The FRP slide shall be of 6 mm thick and should be finished both side with specialty designed horizontal landing where the child is not going to got hurt. (b) Platform height 3.0mtr. of aluminum chequred plate 3 mm thick with railing shall be made up of FRP with safe railing having 20 NB GI pipe for grip, with a height of 500 mm as recommended in the international safety standards. (c) Central support pipe shall be made up of 75 NB G.I ISI mark pipe with suitable arrangement. (length 4.0 m) (d) Ladder, Railing and steps made up of 20 mm NB G.I. pipe with steps for ladder 12 Nos. (length 0.4 m) Platform support pipe shall be made of 40 mm NB G.I. pipe 2nos of (3.5 m per no) G.I. pipe with proper foundation arrangement. The sate play area shall be a minimum of 3.5mtrs x 2.8mtrs. the painting shall be of required quality and support pipe are embedded in C.C. (1:2:4) mix of size 0.45 x 0.45 x 0.50 m and one coat of anticorrosive paint over it two coats of oil painting of approved quality and shade etc. complete as per design and drawing. All pipes are G.I. ISI ‘B’ class.

Wave Slide ( FRP ( Fiber Reinforced Plastic) / Roto Molding ( LLDPE/HDPE) Rec. Age :- 4-12 year The area :- 4.8 m x 0.5 m Safe play area :- 5.8 m x 1.5 m Height :- 1.5 m This item consists of ISI marked structure. The attractive wave slide chute is made up of 4 mm thick fiber reinforced plastic materials. The structure comprises of 20 NB and 25 NB powder coated GI pipe. The center support is made in 80 NB powder coated GI pipe.:The ladder cum railing is made 20 NB and 25 NB GI pipes.The platform is made up of 14 SWG GI sheet with anti skid for firm foot grip. There are triangular steps 16 SWG GI sheet. The chute has its end such as it causes safe landing of the child.All pipes are ‘A’ class pipes. All Structure Are of Powder Coating All Work done as per general Raw Material Sheet Added Below.

Double Arch Swing :- Rec.Age :- 4-14 yrs. The area :- 3 m x 1.5 m Safe play area :- 4m x 3.5 m The arch shaped side frame of the swing is made up of 80 NB GI pipe and top pipe is made up of 50 NB GI pipe.All pipes are ‘A’ class pipes. The frame is powder coated to give an esthetic look. The two swing are made up of 10 mm thick anti skid chequered reinforced rubber top. The belt seat is suspended on 6 mm rubber coated GI chain. The ball clearings are munted inside a specially designed nylon clamp. All Structure Are of Powder Coating All Work Done as per General Raw Material Sheet added Below.

Animal Merry Go Round :- Rec.Age :- 3-12 yrs. The area :- 1.5 m dia Safe play area :- 2.5 m dia The mainframe of the animal merry go round is made up of 25 NB & 40 NB GI pipes. The GI pipes are powder coated. The stand is made in 80 NB GI pipes. All pipes are ‘A’ class pipes. The whole structure is mounted on heavy-duty bearing shaft permanently lubricated with water sealant.The animal seats are made out of molded plastic in rotational molding process (LLDP/HDPE) It accommodates 4 children at a time. All Structure are of Powder Coating All Work Done As Per General Raw Material Sheet Added Below.

Multi Seater See-Saw:- Rec.Age :- 3-10 yrs. The area :- 3m x 0.5 m Safe play area :- 4 m x 1.5 m The MS See-Saw comprises four FRP ( FIBER REINFORCED PLASTIC/ROTO MOLDING (LLDPE/HDPE) Seats The lever is consisted of 20 NB and 80 NB powder coated GI pipes. The bearing used in this item is heavy duty nylon bush type. The stand for see-saw is made using 50 NB GI pipe All pipes are ‘A’ class pipes All Structure Are of Powder Coating All Work Done as per General Raw Material Sheet added Below.

SATELLITE SCRAMBLER :- Rec.Age :- 4-12yrs. The area :- 2.4 M X 2.4 M Safe play area :- 3.4 m x 3.4 m Height :- 3.4 M This item comprises top globular frame, ladder frame and support columm and steps. The pipes used in this item are 25 NB and 40 NB GI pipes.The top globe is fabricated from 25 NB GI pipes supported on a 40 NB vertical GI pipes. All pipes are ‘A’ class pipes. The structure is powder coated to avoid rusting and for esthetic look. The steps of the ladders are made from 15 NB GI pipes. The chain ladder is 7 mm Thick for climbing the scrambler All Structure Are of Powder Coating All Work Done as per General Raw Material Sheet added Below

DOUBLE BAR :- Rec.Age :- 6-14 yrs. The area :- 1.9 M X 1.5 M Safe play area :- 2.9 m x 2.5 m The double bar being from exercise range provides a structure for physical exercise to the children the complete structure is made out using 40 NB powder coated GI pipes. The spacer pipes used are of 25 NB GI pipes All pipes are ‘A’ class pipes. All Structure Are of Powder Coating All Work Done as per General Raw Material Sheet added Below

Simple Side (Galvanized iron Chute) :- Providing fabricating and erecting Simplex Side composed of 40 mm dia G.I. ISI mark 2 Nos. (3.00 m length per no) for supporting plant form, 20 mm dia G.I. Pipe for ladder slant 2 Nos. (3 m length per no) steps 11 nos. (0.40 m per no Railing 2 nos. (2.70 m per no) bracing 4 Nos. (0.20 m per no) and vertical 20 mm NB G.I. Pipe dia G.I. Pipe for hand rest at platform level 4Nos (0.45 m per No) 4 Nos. horizontal (0.50 m per no)and for side chute slant 2 Nos.(4.30 m per no) and for middle vertical support of side chute 2 nos. (1.30 m per no) and the end of chute vertical supports 4nos (0.9 m per nos) also M.S. angle 40 x40 mm x 5 mm as stiffeners below chute and along edges length wise (Total length 10.4mtr.) Railing and support pipe embedded in cement Concrete block (1:2:4 mix) of size 0.45 x0.45 x 0.45mtr and 18 Gauge Galvanize iron sheet for slide chute (4.30 m x 0.45 mtr.) and Aluminum chequred sheet 3 mm thick fixed on ISA 40 x 40 x 5 mm thick for platform size (0.50 m x 0.45 m) and one coat of anticorrosive paint and oer it two coat of oil painting of approved quality and shade etc. complete. As per detail design and drawing. All pipes are G.I. ‘B’ class ISI Mark.

Rain – Bow – Ladder :- Providing fabricating and creating Rain – Bow – Ladder composed of two semicircular 40 mm NB GI ISI mark pipe (length of one pipe 6.28 m) embedded in cement concrete block ()1:2:4 mix) of size 0.45 x 0.45 x 0.45 m and 20 mm NB GI ISI round pipe 19 nos. (0.50 m length per no) for steps at equal spacing and one coat of anticorrosive paint and over it two coat of oil painting of approved quality and shade etc. complete as per detail design and drawing. All pipes are G.I. ‘B’ class ISI mark.

Animal shape Dust Bin (FRP) :- Providing and fixing Penguin / Rabbit shape dust bin of size 2 feet diameter 3.5 feet height made out of animal shape Fiber Reinforcement Plastic structure of 5 mm thick in two colours well finished and smoothened with a door for opening on back side as per drawing and painting in attractive colour combination in synthetic enamels paint.

Tube Slide :- Providing fabricating & erecting Tube Slide of platform height 1.5 m composed of 40 mm NB GI ISI mark 2 nos. (2.1 m length per no) for platform 20 mm NB GI ISI mark pipe of total length 23mtr. includes for Ladder slant 2 nos. (2.25 m Length per no) Steps 7 nos. (0.40 m per nos) Railing 2 nos. (2.0 m length per no) Bracing’s 4 nos. (0.2mtr length per no) and for platform 4 nos. (0.45 m length per no) 4 nos. (0.5mtr length per no) and for support 6nos (1.3 m length per no) and sliding chute in tubular shape shall be made up of fiber glass reinforced plastic ( FRP) 5 mm thick molded both side finish shall be with attractive colour a shade with Translucent dia 0.75 m and Translucent length 3.8 m with aluminum chequered plate 3 mm thick of size (0.5 x .04 m) all railing and support pipes are embedded in C.C. blocks M 15 (1:2:4) grade of size 0.30 x 0.30 x 0.50 m and one coat of anticorrosive paint and over it two coat of oil painting of approved quality and shade etc. complete as per detail design and drawing. All pipes are G.I. ‘B’ class ISI mark.

Spring Duck Rider :- Made in 40 x 40 x5mm thick angle base with heavy duty spring of 2 Nos. with FRP animal duck of 3mm thickness etc. complete

Spring Horse Rider :- Made in 40 x 40 x5mm thick angle base with heavy duty spring of 2 Nos. with FRP animal horse of 3mm thickness etc. complete ( Tender approved rate 2006-07)

F.R.P Security cabin of size 1.8 m x 1.8 m x 2.40 m(Height) with single door and two windows with sliding glass panel including all the sections used in fabrication work must be of required strength and get approved from engineer-in- charge. The cabin should have slopping roof with decorative canopy. ( Tender approved rate 2006-07)

Two seat swing :- providing and fabricating and erecting Two Seat swing composed of to Horizontal ISI mark 50 mm NB G.I. Pipe of 3.0 m in length, vertical inclined G.I. Round Pipe 40 mm NB ISI mark 4nos (2.90 mtr length per No) for leg support and bracing pipe 40 mm NB G.I. Pipe 2 nos. (0.40 m per no) and inclined pipe shall be fixed firmly to top horizontal pipe, leg pipe shall be embedded with hold fast in C.C. bloc (1:2:4 mix) of size 0.45 x 0.45 x 0.45 m and two heavy duty ball bearing assembly for swinging with G.I. chain 8 mm, 4 nos. (2.30 m length per no.) Embedded with hold fast in C.C. bloc (1:2:4 mix) of size 0.45 x 0.45 x 0.45 0.45m and two heavy duty ball bearing assembly for swinging with G.I. chain 8 mm, 4 nos. (2.30m length per no.) and Aluminum chequred sheet 3 mm thick size 0.45 x 0.30mtr per sheet fixed on 15 mm NB G.I. ISI Pipe frame and one coat of anticorrosive paint and over it two coat of oil painting of approved quality and shade etc. complete as per design and drawing.

M/S Aditya Construction Company