SPECIAL REPAIRS TO BLDG NO P-I (INSPECTION BUNGALOW) AT REST HOUSE ROAD AND FOOTPATH AND HARDSTANDING AT OFFICE COMPLEX AND SINGLE LIVING ACCN OF SIGNAL SECTION UNDER GE (SOUTH) BANGALORE

Amount

Demolition of brickwork or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, and precast concrete articles, staking serviceable material and removing debris outside MD land complete all as specified and directed.

M&L for Precast cement concrete type C1 1:3:6 block masonary with solid blocks exc 10cm in width & setting in CM 1:6 complete all as specified and directed.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 incl finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement based paint complete all as specified and as directed.

M&L for preparation of old distempered surfaces of ceilng and applying one coat of oil bound distemper all as including cleaning splashes of distmeper on floor/objects etc complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces of walls and cornices and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old distempered surfaces of walls and applying a coat of Oil bound distemper including stopping of nail holes, filling of cracks, etc and cleaning all window panes from splashes / droppings, complete all as specified and directed.

M&L for complete removal of existing treatment by wire brushing, rubbing down with water of old painted surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistance primer over 1 mm thick birla wall care putty, including stopping of nail holes, filling of cracks, etc and cleaning all window panes from splashes / droppings complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 on ceiling of concrete surfaces finished even and smooth without using extra cement including taking down plaster, including raking out joints, hacking for key, scrubbing down with water etc and removing rubbish of the premises complete all as specified and as directed.

M&L for preparing of newly plastered surfaces and applying three coats of white wash on ceilings complete complete all as specified and as directed.

Taking down cement plaster on brick or stone walls or concrete ceiling etc, incl raking out joints, hacking for key scrubbing down with water, etc. complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:6 on fair face of brick or concrete surfaces of walls finished even and smooth without using extra cement including raking out joints, hacking for key, scrubbing down with water etc and removing rubbish of the premises complete all as specified and as directed.

M & L for applying two coats of Oil bound distemper on newly plastered surfaces incl preparing the surfaces and applying one coat of alkali resistant priming paint complete all as specified and directed .

M&L for complete removal of existing treatment of old treated surfaces of walls including washing, rubbing etc. and aapplying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.

M&L for preparation of old decorated surfaces of walls and applying one coat of premium acrylic exterior paint complete all as specified and as directed.

M&L preparation of old painted surfaces of wood work and joinery exceeding 10 cm width or girth and applying one coat synthetic enamel paint complete all as specified

S&F in repairs galvanised mild steel wire cloth, 0.56 mm nominal ida of wire and average width of aperature 1.18 mm and fixed with tinned tacks, or galvanised wire staples .

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing 3.0mm thick plain galss ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F sheet glass ordinary quality 4mm thick in square not exc 0.50 Sqm each pane glazing with oil putty, clip in metal frame and wooden beading in wooden frame complete all as specified.

S&F in repair 15 mm bore Fancy type Bib taps, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F in repair 15 mm bore diameter CP two way bib taps with crutch or butterfly handle,screwed down, screwed for pipe or for brass ferrule complete all as specified and directed.

S&F in repairs pillar taps, brass, with capston heads, fancy type, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe complete all as specified and directed.

S&F in repairs stop valves male/female threaded 15 mm nominal bore, brass, fancy type, chromium plated, screwed down, high pressure with Capston head, screwed both ends for iron/CPVC pipes or for unions complete all as specified and directed .

S&F in repairs angle valves male/female threaded 15 mm nominal bore, brass, fancy type, chromium plated, screwed down, high pressure with Capston head, screwed both ends for iron/CPVC pipes or for unions complete all as specified and directed.

M&L in repairs 15mm dia CP swan neck long body fancy type sink tap complete all as specified.

S&F in repairs fancy type wall mixture of brass, chromium plated, 2 in 1 system with hot and cold arrangement all as specified and as directed.

S&F in repairs CP Toilet paper holder fancy type 150mm Size with brackets complete all as specified.

M&L in repairs Health Faucet 15mm size, ABS Body, with wall hook and 1 metre stainless steel braided rubber hose pipe complete all as specified .

M&L for towel ring 200-250mm dia made of heavy duty stainless steel pipe or chromium plated all as specified and as directed.

M&L for stainless steel peg set of 06, 450mm long as specified and as directed.

S&F 304 grade stainless steel folding towel rack 24 inch, curved design, wall mounted type, chrome finish including 4 nos hook, 01 towel rod supported with wall flats, tubular pipes fixed with chromium plated concealed screws complete all as specified.

S&F in repairs Glass corner shelf including CP railing, radius 250 mm complete all as specified and directed.

S&F in repair vitreous china wash hand basin, snowwhite countersop of size 750x380x130mm including taps waste chain and plug and porecelain stopper but incl brackit and cutting fair pinning in ends of brackets complete all as directed flat back size 550 x 400 mm excluding taps, waste pipe chain and plug and porecelain stopper but incl brackets and cutting for pinning in ends of brackets complete all as specified and directed.

S&F in repairs EWC with integral flushing cistern of vitrous china (one piece) white or coloured including fixing bolts and flush pipe, seat cover, hinging device, 'P' or 'S' trap WC connector etc, complete all as specified and directed .

S&F in repairs sink with drainage board made of stainless steel 1 mm thick, kitchen or laboratory, with plugs, washers and wastes coupling, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe over all size 915mm x460mm bowl size 405mm x 355mm x 178mm (minimum), including PVC waste pipe 40 mm dia complete all as specified and directed.

S&F in repairs brass chromium plated grating 125 mm dia circular with centre hole/ without hole of approved make and fixing with cement mortar 1:3 on Nahani trap or floor trap complete all as specified.

S&F in repairs Swivel shower rose 15mm of brass chromium plated 150 mm dia round with shower arm of 190mm Long Light Body complete all as specified and directed .

S&F in repair tubular towel rail 600 mm long of brass chromium plated 20 mm dia D type 60 cm long fixed with two plugs (gutties) of 2nd class hard wood embedded in cement mortar 1:3 with MS screws complete all as specified.

S&F in repair 32 mm dia PVC waste pipe for WHB complete all as specified.

M&L in repairs 32mm dia Waste coupling, brass, chromium plated for SS Kitchen sinks, WHB etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified.

S&F in repairs fancy type brass bracket with screw 20-25 mm dia including wooden plugs, scews etc complete all as specified.

S&F in repairs fancy type stainless steel bracket with screws for wall /corners 20-25 mm dia including wooden plugs complete all as specified.

S&F in repairs coloured mild steel powder coated curtain rods 25 mm dia 1mm wall thickness all as specified .

S&F in repairs stainless steel medium weight curtain rods 25 mm dia all as specified .

S&F in repair PVC (SWR) pipes 75 mm size in bore single socketed , in any length with rubber ring joints, fixed to walls including dismantling and breaking of pipe and fittings complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 110 mm size in bore single socketed , in any length with rubber ring joints, fixed to walls including dismantling and breaking of pipe and fittings complete all as specified and as directed.

S&F 75mm PVC (SWR) bends any radius complete all as specified and as directed.

S&F 110mm PVC (SWR) bends any radius complete all as specified and as directed.

S&F 75mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frame)n. exc 1.5 sqm complete all as specified and directed.

Taking down chowkat or frames with shutter (without taking off shutters from the frame) exc 1.5 sqm but n.exc 4 Sqm etc complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm but n. exc 2.00 Sqm complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube and fixing in position with hold fast, complete all as specified and directed. (Cost of hold fast included in the unit rate of this item.)

M &L factory made solid pannel PVC door shutter 30mm thick (style) consisting of frame made out of MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck in side with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame wedded /sealed to the styles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at side,including two Nos tower bolts/ Handles for each shutter as per specification and drawing upto complete all as specified and as directed.

S&F sheet glass 4.8mm thick ordinary quality, in squares n exc 0.5 sq. m each pane complete all as specified and directed.

All as per item no.58 but 4.8mm thick sheet glass exc 0.5 sq. m each pane complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.56 mm nominal ida of wire and average width of aperature 1.18 mm and fixed with tinned tacks, or galvanised wire staples all as specified and as directed.

M&L for powder coated aluminium window sliding on two or three tracks, including aluminium shutter sections weighing not less than 0.37 kg/RM and frame bottom 0.55 Kg/RM, frame top and sides 0.43 Kg/RM including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, stainless steel screws, anodised aluminium fittings such as locking arrangements, rollers etc complete all as specified and directed.

S&F aluminium anodised frame for doors, windows vetilators with one of more rebates incl joining cleat for fixing etc, with powder coating complete all as specified and directed.

S&F powder coated, min thickness (50 micron) aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

S&F 19mm thick prelaminated particle board, interior grade, prelaminated both sides with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F stainlees steel 150mm door handles with stainless steel screws all as specified and as directed.

S&F stainlees steel 150mm tower bolt with stainless steel screws all as specified and as directed.

S&F stainlees steel 250mm sliding door bolt with stainless steel screws all as specified and as directed.

S&F in repairs alumiium cast type Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg

S&F in repairs alumiium cast type Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg

S&F floor door stopper(double) of aluminium alloy body and tongue anodised with hard drawn steel spring fixed to door overall length of cover plate 140mm complete all as specified

S&F stainless steel 100 mm butt hinges for doors complete upto 5th floor of bldgs all as specified.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing servicieable tiles to store and rubbish off the premises.

M&L 25 mm thick cement concrete type B-0, 1:2:4 (using 12.5 mm graded crushed stone aggregate), as in sub base of floors.

S&F Vitrified ceramic coloured tiles 10 mm thick (square/rectangular) area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6.

S&F Vitrified ceramic coloured tiles 10 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6.

S&F coloured non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white cement or coloured cement to match over 15 mm thick screed bed in cement mortar 1:6.

M&L glazed ceramic tiles in vertical surface 350x450x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of tiles including rendering 10 mm thick in cement mortar 1:6 complete all as specified & directed.

Dismantling existing water proofing treatment any type and thickness from top surface of roof slab and removing rubbish off the premises all as specified and as directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on concrete surfaces mixed with integral water proofing compound as per manufacturer's instructions, surfaces finished even and smooth without using extra cement complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid separately as supply only under relevant item of this schedule)

Demolition of cement concrete (reinforced) in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in roof/floor complete all as specified and directed.

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work n exc 15 cm in width or girth including cutting to edges, all mitres and stopped ends, etc.

Preparing the surface by Chipping of the loose/dead concrete, preparing the surface by removing the dust and laitance etc, Identify cracks and groove cut the cracks which is >5mm, clean the cracks and fill the same with precision grout or PU Sealant. Apply one coat of polymer based priming bond coat 1:4:7 (polymer, water and cement) to seal all the pores on the treated surface. Lay 45GSM glass fibre mesh (on horizontal surface only) or geo textile on the primed surface while it is in tacky condition. Apply two coats of PU RoofKoat/Davko K10 on the Glass Fibre Mesh with a gap of 3-4hrs between the coating complete inlcuding taking down and refixing of water supply lines, cabes etc all as specified and as directed. Make - STP/Berger/Cico/Pedilite

All as per item No 83 above but on newly plastered and finished suface of roof.

Supply only integral water proofing compound complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar incl removal of debries out side MD land.

M&L 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs,pillars, window cills, cooking platforms andlike in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with the granite complete all as specified and directed.

S&F assembled ready to use stainless steel grade 304, kitchen plate rack inlcuding top/middle shelves of 1.0mm thick sheet, square hollow supports, including bottom hooks, spoon holes, front and back open, size 915x915mm including taking down old rack all as approved and specified.

M&L for fabrication of kitchen or other cabinets, cupboards etc of openable shutters, shelves partitins, drawers etc made up of 20mm solid core ply finished with 1mm veneer ply on both faces, each shutter having a pair of self closing hinges, stainless steel fancy handles, tower bolt and other fittings as directed, taking down old cabinets, S&F solid wood frame complete all as specified and as directed. Note - 1. Surface area of each member is measured flat for payment. 2. S&F of all necessary hardware deemed to be inclusive in quoted rates.

Cleaning of scales, dirt from 500 ltr capacity PVC tanks, pipe mouth etc over roof of accessible/non accessible roof, including taking down and refixing if required, writing date of cleaning with stensil or other suitable method in Itallic or arial fonts 150mm height all as specified and as directed.

All as per item no.90 above but 1000 ltr capacity tanks.

S&F in repairs HDPE PVC lid (cover) for 500/1000 ltr capacity PVC water tank all as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) incl staking serviceable material and removing debris outside MD land complete all as specified and directed.

M & L reinforced cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone agg) as in foundation, incl rafts, footings, foundation beams, plinth beams, Cooking plateform bases for columns etc, basement slabs under reamed piles and mass concrete.

Formwork to sides of flat concrete foundations, footings, based of columns, rafts and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter.

S&F mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (anealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S&F mild steel TMT bars 5mm dia and over upto and incl 10 mm dia, cut to length, bent to shape required, incl cranking, bending spirally for hooping for in stirrups, spaces and binders and incl mild steel wire (anealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering.

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete with Mild steel grad Fe 410 -W (GdeE- 250) qualityA all as specified and directed..

M&L Sand filling under floors or in foundations including watering and consolidation as sand cushioning complete all as specified and directed.

M&L hardcore of broken stone or boulders of gauge n.exc 63mm deposited spread and leveled in layer n.exc 15 cm thick, watered and rammed to a true surface complete all as specified.

M&L 100mm thick Cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base.

M&L 75mm thick Cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base.

S&F chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors over 15 mm thick screed bed in cement mortar 1:6. complete all as specified

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F 1.8 mm thick plain, galvanised, zinc coating mild steel plain sheeting in ridge, hips, valley gutters, drip and straight flashing (length and grith as fixed) with grade of zinc coating 275.

M&L preparation of new or previously untreated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enemel paint over a coat of red oxide.

M&L preparation of old painted steel and iron surfaces of roof trusses or any description, over 10 cm in width or girth, not otherwise described and applying one coats of synthetic enemel paint.

Dismantling Wall and Ceiling Boards any thickness, all as specified and directed

M&L for false ceiling with 12 mm thick gypsum board in ceiling fixed on frame work of GI section, the main runner of 22 gauge GI sheet and cross runner of 24 gauge GI Sheet must be framed to form a mesh 0.6 x0.6 mtr centre, the gypsum board must be fixed to GI frame and joint to be properly filled in with POP paste and paper tap to get a levelled to smooth ceiling. Recessing of Gypsum board for fixing for light fixurs must be done with extra frame work of GI to hold the concealed light fixture etc including two or more coats of Plastic emulsion paint on ceiling with putty work designer complete all as specified and as directed.

S&F in repairs Stainless steel polished curtain rod medium weight 25mm dia with and including support wall bracket of and end knobs of polished stainless steel all as specified.

S&F Stainless steel polished wall brackets for holding curtain rod medium weight all as specified.

S&F in repairs Stainless steel polished end knobs spherical in shape suitable for 25mm rodall as specified.

Demolition of cement concrete any description and in any position not otherwise specially provided for and removing debries out side the MD land.

M&L 20mm thick Screed bed or bedding layer in cement mortar 1:6 for laying chequered tiles complete all as specified and directed.

M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment laid over 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M&L for point wiring with 1100 Volts grade 1.5 sqmm PVC insulated FRLSH unsheathed cable with multistandred copper conductor conforming to IS: 694:1990 (for Phase, Neutral and and Earth) in and including Non metalic PVC rigid condiut medium grade/ casing caping sutaible at site with ISI mark of appropriate size with all accessories laid in wall/ ceiling/floor etc, concealed with GI flush in box/terminal boxes of sutaible size, including front plate for mounting of modular switch/ socket and combined cover plate with fitting screw washer, including cutting chasses in wall/floor/roof for fixing of conduit and flush in box and making good the distributed surfaces matching with existing complete all as specified and as directed for following- One light/ Bell/ fan point controlled by one switch

All as per Item No 120 above here in before but for Modular type Socket 6/10 Amp of two module in independent board, 230 volts complete all as specified and directed by Engr-In-Charge.

All as per Item No 120 above here in before but for Modular type Socket 6/10 Amp of two module on same board, 230 volts complete all as specified and directed by Engr-In-Charge.

All as per Item No 120 above here in before but for Modular type additional light / fan point on the same switch circuit mounted on same switch board controlled with separate switch, 230 volts complete all as specified and directed by Engr-In-Charge.

All as per Item no 120 above here in before but with 2.5 sqmm PVC insulated FRLSH unsheathed cable with GI Flush in box for modular switch/ socket 16 Amps of sutaible size as required with front plate for mounting of modular switch/ socket and combined cover plate of as required at site complete all as specified and as directed by Engr-in-Charge.

S&F for modular switch piano, flush type single pole, one way 16 Amps, 230 Volts complete all as specified and directed by Engr-In-Charge.

S&F for Modular type Socket 6/16 Amp two way of 230 volts complete all as specified and directed by Engr-In-Charge.

S&F for modular switch piano, flush type single pole, one way 5/6 Amps, 230 Volts complete all as specified and directed by Engr-In-Charge.

S&F for Modular type Socket 6/10 Amp of two way point complete all as specified and as deirected by engr in charge

S&F for Modular type fan regulator 1/2 module as reqd, 230 volts complete all as specified and directed by Engr-In-Charge.

S&F for Modular type bell push switch one way 6/10 Amps, 230 volts matching with existing complete all as specified and directed by Engr-In-Charge.

S&F Call bell AC, 230 Volts matching with existing sample complete all as specified and directed by Engr-In-Charge.

M&L ceiling rose surface bakelite 65x50 mm two to three terminals.complete all as specified and as directed by Engr-In-Charge.

S & F of Single pole and neutral enclosure 10Amp, 230V with a two pin and earth plug and socket complete with one single pole MCB 230V complete all as specified and as directed by Engr-In-Charge.

M&L sub main wiring surface type with two runs of single core, PVC insulated, unsheathed multi standard copper conductor cable of size 10 Sqmm, 1100 volts grade (FRLS) and one run of 10 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through concealedin wall PVC conduit complete all as specified and as directed by Engr-In-Charge. (Note :- Two runs of 10 Sqmm cable, one run of 10 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length).

M&L sub main wiring surface type with two runs of single core, PVC insulated, unsheathed multi standard copper conductor cable of size 6 Sqmm, 1100 volts grade (FRLS) and one run of 6 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through concealedin wall PVC conduit complete all as specified and as directed by Engr-In-Charge. (Note :- Two runs of 6 Sqmm cable, one run of 6 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length).

S & F in replacement VTPN DB - Dobule Door made out of CRCA mild steel sheet flushed in wall, TPN 4 way with 200 Amp rated bus bar, 415 volt with PVC MCB blanking plate, stove enamelled for incorporated of MCBs, insulators and MCCB of capacity upto 125 Amps TP/FP etc, complete all as specified and as directed by engineer in charge

S&F MCB, DB double door type, made out of CRCA mild steel sheet flushed in wall, SPN 8 way with 200 Amps rated bus bar , 240 volts IP-43, with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc including complete all as specified and as directed complete all as specified and as directed by Engr-In-Charge.

Supply and fixing MCCB FP 415 Volts 100 Amps, 16 KA complete all as specifed and directed by Engr-In-Charge.

Supply and fixing MCB SPN 40 Amps, 240 Volts complete all as specified and as directed by Engr-In-Charge.

Supply & fixing MCB SP 06-40 Amp, AC, 240 volts, complete all as specified and as directed by Engr-In-Charge.

Supply and fixing surface & wall mounted LED batten 4feet with extruded aluminium housing and robust construction 20 W system lumen including flexible copper 2 core wire from tube light fitting to ceiling rose required length with all accessories all as specified and directed by Engr-in-Charge.

Supply and fixing surface & wall mounted LED batten 2feet 10 W with luminious efficacy not less than 100 lumen/watt including flexible copper 2/3 core wire from tube light fitting to ceiling rose with mounting provisions and all accessories with color of light warm white/cool day light as reqd at site complete all as specified and directed by Engr-in-Charge.

S&F in replacement wall mounting fancy light fitting in plastic body with lamp holder B22 base and diffiuser sutaible for and including 9w LED Lamp of colour as decided with mounting provision complete all as secified as directed by Engr-in-Charge.

Supply and fixing round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by Engr-In-Charge.

S&F LED weather proof bulk head light fitting of shape and size as per site requirment of wattage upto 10 watt light fitting with mounting clamp, LED driver holder, LED lamps etc including connecting up to in celling rose complete all as specified and as directed by Engr-in-Charge.

S&F in replacement LED recess/surface mounting as reqd 2x2 fittings 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with deffuser glare free light complete with driver, holders & LED lamp of colour as decided suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as derected by Engr-in-Charge

S & F post top lantern LED 15W made up of pressure die cast aluminium housing and LEDs as a light source prewired with electronic driver suitable for 15 watts light fitting with IP 65 protection with Surge protection device for protection of LED driver, lumen efficacy of light fitting shall be not less than 100 lm/W. with necessary mounting arrangements including taking down old unserviceable light fitting.complete all as specified and directed by Engr-in-charge.

S&F wall washer light fitting crafted from aluminium die cast with Bi- Directional beam integreated long lasting and IP-65 protected outdoor type of shape and size as per site requirment of wattage upto 10 watt light fitting with mounting provision etc including connecting up to in three core cable complete all as specified and as directed by Engr-in-Charge.

S & F Junction Box for Street Lights of size minimum 205x255x112 mm made out of Polycarbonate material totally enclosed, dust and vermin proof, rain protected , door pasted with rubber gasket, water tight IP 65 protection with teriminal box for three phase 4 wire system of rating min 32 Amps suitable to terminate LT Cable of size upto 25 sqmm.with option to mount one no MCB SP 06 amps including cable glands at both incoming and outgoing side mounted on security light pole with suitable bracket nuts, bolts including removal of exiting unsv all as specified and directed.

S & F LED flood light 30W made up of pressure die cast aluminium housing wth toughened glass and LEDs as a light source prewired with electronic driver suitable for 30 watts light fitting with IP 65 protection with Surge protection device for protection of LED driver, lumen efficacy of light fitting shall be not less than 100 lm/W. with necessary mounting arrangements colour as per deside at site including taking down old unserviceable light fitting.complete all as specified and directed by Engr-in-charge.

S&F in replacement wall mounted fan motor of 400 mm sweep plastic body complete with rotor, stator, outer body, blades, front and rear grills, fan regulator, swing system and other connected accessories including mounting provisions matching with existing complete all as specified and as directed by Engr- in- Charge.

Taking down unserviceable ceiling fan, wall mounted fan, cabin fan, exhaust fans etc of any type and size from position, disconnecting electric supply, repair/replacement of unserviceable items, including cleaning oiling/greasing,tightening of nut bolt and refixing matching with existing. complete all as specified and directed by Engr-In-Charge.

Supply only following items to be fixed under item no -29 complete all as specified and directed by Engr-In-Charge.

Ball/Roller bearing of size and shape matching with existing suitable for ceiling fans

Gun metal bush of size and shape matching with existing suitable for ceiling fans

Motor stator for ceiling fans wounded with copper wire of size matching with existing with insulation with casing complete.

Motor rotor prewired for ceiling fans of size and type matching with existing

Fan blades for ceiling fan of any type and size matching with existing

Plastic cup with screw for ceiling fans

Rubber bush with MS bolts, nuts & washers with 'U' clamps for ceiling fans complete all as specified and as directed.

S&F in replacement capacitor 2.5 Mfd suitable for ceiling / exhaust /wall mounting fans complete all as specified and as directed.

S&F in replacement down rod of 30/45 cm with nut, bolts and safety pin for ceiling fans complete all as specified and as directed.

M&L for Preparation of surface & painting the ceiling fans with blades complete after cleaning & applying one coat of stove enamelled white paint by spray painting, writing No complete all as specified & as directed by Engr -in-Charge.

Taking down, dismantling of geysers of any type/capacity from site for repair and Inspection, cleaning, descaling, brazing inner tank, internal wiring including replacement of unserviceable items as reqd, reassembling & reinstallation after necessary repair incuding testing after repair complete all as specified & directed. Note :(a) Replacement of major unserviceable items shall be measured & paid separately under respective item of work.. (b)Cost of replacement for minor items like washers, gaskets, nuts, bolts etc and items not mentioned below is deemed to be include in quoted rates.

Supply only following items to be fixed under item no -32 complete all as specified and directed by Engr-In-Charge.

Inner tank for geyser of capacity 25 ltrs of shape matching with existing.

Siphon Assembly suitable for geyser of capacity 25 ltrs of shape matching with existing.

Heating element rated 1.5/2.0 KW with mounting provisions round/tikona as reqd of shape matching with existing

Thermostat with auto cutoff provision switch capillary/screw type, with range 0-80 deg celcius of shape and size matching with existing suitable for geyser of capacity 25/50 Ltrs.

Indicator lamp red and green with coloured diffuser for geysers matching with existing.

Safety valve/high pressure valve matching with existing for geysers

NRV for geysers matching with existing.

Base fixing cover matching with existing.

Cover outer for geyser of capacity 25/50 ltrs of shape and size matching with existing.

M & L earthing complete with GI earth plate Electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth plate not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanished earth wire 4.0 mm dia by means of bolts, nuts check and washers of GI or steel all as shown in electrical plate No. 3 of SSR Pt -I connected to earthing test point all as specified or indicated including GI pipe 15 mm dia light grade for earth wire protection, necessary excavation, earth work in any type of soil, PCC chamber and RCC cover slab, connecting lead wire from test point to DB complete all as specified & as directed by Engr-In-Charge.

Supplying and fixing 1100 volts grade heavy duty cable PVC insulated multi stranded aluminum conductor, 10 Sqmm twin core served with inner sheathing of PVC tape and overall PVC sheathed in service connections complete all as specified and directed by Engr-In-Charge

Supply and fixing Rigid PVC conduit 20MM inclusive of medium grade boxes and of all tees,bends,elbows,reducers,bell mouth tube ends and fixing accessories such as couplers,lock nuts,saddles,pipe hooks etc.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 Sqmm x 4 core including taking down unserviceable UG cable complete all as specified and directed by Engr-In-Charge.

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth for laying of UG cables etc and getting out in soft /loose soil complete all as specified and as directed by Engr-In-Charge.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cms in any type of soil complete all as specified and as directed by Engr-In-Charge.

Removing excavated soil to a distance not exceeding 50 mtrs and depositing where directed at a level not exceeding 1.5 M above the starting point all as directed.

M&L for sand cushioning in trenches for bricks of u/g cable with coarse sand laid dry in trenches with uniform thickness complete all as specified and as directed by Engr-In-Charge.

Supply and lay burnt bricks of sub class 'B' laid dry across in trenches for cable protection all as specified and directed Complete all as specified and as directed by Engr - In - Charge.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundation, mass concrete for road crossing etc., complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in foundation, mass concrete for road crossing etc., complete all as specified and directed.

Supply and laying 25 mm GI pipe fitting tubes medium grade galvanished with all fittings complete laid in trenches including taking down the old unserviceable GI pipe from trenches Complete all as specified and as directed by Engr-In-Charge.

Supply and laying 20 mm GI pipe fitting tubes medium grade galvanished with all fittings complete laid in trenches including taking down the old unserviceable GI pipe from trenches Complete all as specified and as directed by Engr-In-Charge.

S & F float valves of size 20 mm and as reqired at site as complete brass fitting with rod and plastic ball Complete all as specified and as directed by Engr-in-in Charge.

S & F gun metal gate valve with inner wheel head, screwed both ends in iron pipe and fixed of Size 20 mm Complete all as specifed and as directed by Engr-In-Charge.

ANTTARANGNI INTERIOR (BID ID -3459338)

ABHISHEK CONSTRUCTIONS (BID ID -3460608)

S S CONSTRUCTIONS (BID ID -3459852)

Elite Constructions (BID ID -3460254)