CONSTRUCTION OF TRANSIT FACILITY FOR OFFICERS AT PALAM DELHI CANTT

EARTH WORK, EXCAVATION & DISMANTLING Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. (a) All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. (a) All kinds of Soil

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. (a) All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. (a) Ordinary rock

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. (b) Hard rock (blasting prohibited)

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. : All kinds of soil

Carriage of Lime, moorum, building rubbish By Mechanical Transport including loading, unloading and stacking beyond 5 km upto 10km

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming & watering, lead up to 50m & lift upto 1.5m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. (a) Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer in- charge.

ANTI-TERMITE TREATMENT Supplying chemical emulsion in sealed containers including delivery as specified. (a) Chlorpyriphos / Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for Post Construction anti-termite treatment (excluding the cost of chemical emulsion) : (a) Along the external wall below plinth protection concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc.: (i) With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Diluting and injecting chemical emulsion for Post Construction anti-termite treatment (excluding the cost of chemical emulsion) : (b) Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : (i) With Chlorpyriphos/Lindane E.C. 20% with 1% concentration.

Diluting and injecting chemical emulsion for Post Construction anti-termite treatment (excluding the cost of chemical emulsion) : (c) Treatment at points of contact of wood work by chemical emulsion Chlorpyriphos/ Lindane (in oil or kerosene based solution) @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.

PLAIN & REINFORCED CEMENT CONCRETE Providing and laying cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing. (a) 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) grade excluding the cost of centering and shuttering - All work up to plinth level.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. (a) All works upto plinth level. Concrete of M30 grade with minimum cement content of 350 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. (b) All works above plinth level upto floor V level. Concrete of M30 grade with minimum cement content of 350 kg /cum

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (a) Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centring and shuttering including strutting, propping, etc. and removal of form for the following items of RCC work at all depths and heights complete as per drawings, specifications and as per direction of Engineer-in-charge. (a) Foundations, footings, bases of columns, etc. for mass concrete.

Centring and shuttering including strutting, propping, etc. and removal of form for the following items of RCC work at all depths and heights complete as per drawings, specifications and as per direction of Engineer-in-charge. (b) Suspended floors, roofs, landings, balconies and access platform.

Centring and shuttering including strutting, propping, etc. and removal of form for the following items of RCC work at all depths and heights complete as per drawings, specifications and as per direction of Engineer-in-charge. (c) Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centring and shuttering including strutting, propping, etc. and removal of form for the following items of RCC work at all depths and heights complete as per drawings, specifications and as per direction of Engineer-in-charge. (d) Columns, Pillars, Piers, Abutments, Posts and Struts.

Centring and shuttering including strutting, propping, etc. and removal of form for the following items of RCC work at all depths and heights complete as per drawings, specifications and as per direction of Engineer-in-charge. (e) Stairs, (excluding landings) except spiral-staircases

Centring and shuttering including strutting, propping, etc. and removal of form for the following items of RCC work at all depths and heights complete as per drawings, specifications and as per direction of Engineer-in-charge. (f) Weather shade, Chajjas, corbels etc., including edges

Centring and shuttering including strutting, propping, etc. and removal of form for the following items of RCC work at all depths and heights complete as per drawings, specifications and as per direction of Engineer-in-charge. (g) Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20m nominal size) over 75mm bed of dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

Add for using extra cement in the items of design mix over and above the specified cement content therein.

MASONRY WORK Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : (a) Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. (a) Cement mortar 1:4 (1 cement :4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

FINISHING AND SURFACE TREATMENT 6mm cement plaster of mix for celling: (a) 1:3 (1 cement : 3 fine sand)

12 mm thick cement plaster with cement mortar 1:6 (1 cement: 6 coarse sand) on internal surfaces of walls (brick or concrete surfaces) finished smooth with trowel including scafolding, curing etc., complete at all heights : (Internal finishing side)

15 mm cement plaster on rough side of single or half brick wall of mix: (a) 1:6 (1 cement: 6 coarse sand)

Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): Flush / Ruled/ Struck or weathered pointing

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. : per bag of 50kg cement used in the mix

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour (a) New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : (a) Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and fixing of plaster mesh made out of galvanized iron of nominal thickness 0.35mm with a zinc coating of 120 gms per sqm at the junctions of masonry and concrete works including tying in position with suitable nails/screws etc. complete.

20mm thick water proof plastering in cement mortar 1:3 (1 cement : 3 coarse sand) in two layers of 10mm each with water proofing compound mixed as per approved manufacturers specification finished neat with extra cement including blenching, haunching and providing proper slope all as directed. For Chajja & Sunken Slab portions.

French spirit polishing two or more coats on new works including a coat of wood filler and preparation of surfaces etc. complete to give even and smooth glossy mat finish all complete as approved and directed.

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc Cement 0.152 cu.m per100 sq.m.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. (a) New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm at all heights.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete

FLOORING Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete. (a) Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. (a) Size of Tile 600x600 mm

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.: 1200x600mm Size.

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. (a) Granite stone slab colour black, Cherry/Ruby red (i) Area of slab upto 0.50 sqm

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. (a) White Agaria Marble Stone

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. : 8mm thick (a) Raj nagar plain white marble/ Udaipur green marble/ Zebra black marble

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. : 8mm thick (b) Granite of any colour and shade

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing GRC decorative Jali for cladding weight less than 4kg/sqfft of approved colour and design including all complete fittings as per direction of Engineer-In-Charge

Wall lining butch work upto 10m height with Dholpur stone 40 mm thick rough facing on the exposed surface with stone strips of minimum length 300 mm and required width, including embedding every tenth layer and bottom most layer in masonry or concrete after making necessary chases of size 75x75 mm and by providing layer of 75 mm thick strips i/c 12 mm thick bed of cement mortar 1:3 (1 Cement : 3 coarse sand) i/c ruled pointing in cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment to match the shade of stone complete as per direction of Engineer-in-charge.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : (a) Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing vinyl flooring, 4.5mm thick densely compacted Sports flooring, Glass Fiber tissue Impregnation for high dimensional stability, cushioned sports flooring in roll form and skirting in pattern in width of 2.0mtr and 15mtr length ,solid ,resilient ,fully flexible, with PUR guard and protective wear layer of 500 microns , in approved shade , Installation and considering the wastage after cutting the rolls to fit the floor size and also providing thermal welding for a seamless floor providing uniformity and on a smooth and moisture free levelled floor surface using rubber based adhesive Fevicol SR 505 manufactured by Fevicol , all complete and as per the instruction of the engineer in charge

Providing and fixing Premium interlock, 100% Glue-less, SPC flooring planks, 4.00 mm thickness of size 180 mm x 1220 mm in wooden surface texture, high strength wear layer of 300 microns, surface protection for antistain and ease in maintenance , and skirting in approved design and shade, Installation (considering the wastage) on a smooth and moisture free leveled floor surface, all complete and as per the instruction of the engineer in charge .

STEEL WORK Steel work welded in built up sections / framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. (a) In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer- incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. (a) 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Extra for providing mechanical device chain and crank operation for operating rolling shutters. - Exceeding 10.00 sqm and upto 16.80 sqm in the area

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

ALUMINIUM, WOOD & PVC WORK. Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. (a) 180x150 mm size P type

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) : 35 mm thick

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/ clerestory windows & desertory other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs /SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 50 x 100 mm

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). (a) Second class teak wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) (a) Second class teak wood (i) 35 mm thick shutters

Polishing in high gloss/matt finish melamine clear polish on wood work in required color/ wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes / grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. (a) With 12 mm mild steel U beading

Providing and fixing brass sliding door bolts with nuts and screws etc. complete. (a) 300x16 mm

Providing and fixing brass sliding door bolts with nuts and screws etc. complete. (b) 300x16 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : (a) 250x10 mm

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : (b) 200x10 mm

Providing and fixing bright finished brass handles with screws etc. complete (a) 125mm

Providing and fixing bright finished brass handles with screws etc. complete (b) 100mm

Providing and fixing of rubber nylon door buffer (dia of 40mm and 50mm long) on wall with rowl plug and screw.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene gaskit etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) : (a) For fixed portion (i) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene gaskit etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) : (b) For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separately). (i) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing stainless steel (SS 316 grade) adjustable friction window stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in charge complete. (a) 205 x 19 mm

ALUMINIUM WORK Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. (a) Upto 5mm depth and 5 mm width

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM / Neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) : (a) With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM / Neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) : (b) With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.

Providing & fixing Horizontal blinds 100mm wide of washable synthatic material with extruded powder coated hearail housing control units spacers, runners, tilt rod with reduction gear mechanism tilt control for 180 degree Louvers made of approved fabric and colour having scratchgurd coating to be provided. Horizontal Blinds made of glass fibre fabrics in width 5” (or 4”). Minimum overlapping of ¾” in fabric. Top aluminium anodized rail of 1.4 mm thickness.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.: With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. (a) 10 x 80 mm

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. (b) 10 x 120 mm

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875 – Part 3 (ii) Sites with structure height more than 20m for all wind speeds (a) Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. (i) Using R4 series with frame (64mm & above) x (45mm & above) & sash (44mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every panel along with multi-point locking system (Height above 1.8m).

Providing and fixing double glazed hermatically sealed glazing in aluminium windows, ventilators and partition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant) etc. as per specifications, drawings and direction of Engineer-in-charge complete.

Providing and fixing bright finished brass casement stays (straight peg type) with necessary screws etc. complete : (a) 250 mm weighing not less than 280 gms

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : (a) 2nd class teak wood (i) 50 x 20 mm

ROOFING Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conformingto IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer- in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer- in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes (a) 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. (b) Bend 87.5° : 110mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. (c) Shoe (Plain) : 110mm shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.: 110 mm

Providing and applying integral crystelling slurry of hydrophilic in nature for water proofing treatment to the RCC structures like retaining walls of the baseemnts, water tanks,roof slabs, podiums, reservoir, sewage, and water treatmemt plant, tunnels/ subways and bridge deck etc. , prepared by mixing in the ratio of 5:2 ( 5 parts of integral crystelling slurry : 2 parts water ) for vertical surface and and 3:1 ( 3 parts of integral crystelling slurry : 1 parts water) for horizontel surface and applying the same from negative ( internal) side with the help of synthetic fibre brush, the materials shallmeet the requirements as specified in ACI- 212- 3R- 2010 i.e. by reducing permeability of concrete by more than 90 percent compared with contro concrete as per DIN 1048 and ressistant to 16 bar hydrostatic pressure on negative side the crystelline slurry shall be capabele of self healing of crack up to a width of 0.50 mm. The work shall be carried out all complete as per specifications and the direction of the engineer in charge. the product performance shall carry guarantee for 10 years against any leakedge for vertical surfece of two coats @ 0.70kg / SQM.

Providing and fixing tiled false ceiling of specified materials of size 595x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. (a) 12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing

Providing and fixing tiled false ceiling of specified materials of size 595x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. (b) GI Metal Ceiling Lay in perforated Tegular edge global white colour tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. (a) With 16 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.55 to 0.6

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of Engineer-in-Charge all complete. (a) With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges Plain (500-600 mm)

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : (i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer.: Using rough kota stone.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : Using rough Kota stone

Providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear meter (expansive nature) for construction joints treatment of RCC structure such as raft slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining walls etc.. After cleaning the surface, one coat of required primer for swellable water stop tape shall be applied throughout the length of the joint @3.78 litre per 240 running meter. Over the primed surface swellable type water stop tape shall be placed. The work shall be carried out all complete as per specification and the direction of the Engineer-In-Charge. The product performance shall carry guarantee for 10 years against any leakage.

Providing, applying and finishing roof top and other structure surface with silicon adhesive based heat resistant paint of approved brand and manufaclture at all locations including preparation of surface, applying a priming coat, two coats of paint complete as per direction of engineer-in-charge

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm)

SANITARY INSTALLATIONS & PLUMBING Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid , 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required, make : Hindware Code : Sleek Plus Single Flush Star white, with all fittings and fixtures / Hindware / Paryware / equivalent . (a) W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required (a) One urinal basin with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: (a) White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing CP brass health faucet 15mm nominal bore and premium quality including wall outlet with shower hook in round shape, easy flex tube in chrome finish 1m long with nuts etc. all complete as per the directions of Engineer-in-charge.

Providing and fixing CP brass wall mixer 15mm nominal dia of quality & make as approved by Engineer-in-charge.

Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : (a) Kitchen sink with drain board : 510x1040 mm bowl depth 250 mm

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.:Semi rigid pipe (a) 32 mm dia

Providing and fixing S.S towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Internal Drainage Providing, fixing and jointing UV stabilized SWR (Type -B· 6 Kg pressure rating ) pipes conforming to IS:13592 including all fittings such as bends, clamps, tees, cowls, clean out plugs, offsets, Y -tees, tees, door fittings, cUps, clamps, stays etc. conforming to IS-14735, including jointing with rubber gasket fixing in sunk areas, Fixing at wall / ceiling level supported by steel clamps & hangers etc. including Cutting, chases/ holes in floors / walls / slab and making good the same after pipe have been duly laid and testing complete in all respects. (a) 75 mm diameter

Internal Drainage Providing, fixing and jointing UV stabilized SWR (Type -B· 6 Kg pressure rating ) pipes conforming to IS:13592 including all fittings such as bends, clamps, tees, cowls, clean out plugs, offsets, Y -tees, tees, door fittings, cUps, clamps, stays etc. conforming to IS-14735, including jointing with rubber gasket fixing in sunk areas, Fixing at wall / ceiling level supported by steel clamps & hangers etc. including Cutting, chases/ holes in floors / walls / slab and making good the same after pipe have been duly laid and testing complete in all respects. (b) 110 mm diameter

Providing and fixing soil, waste and vent pipes : 100 mm dia Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989

Providing and fixing S.S. towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing terminal guard : 100mm (a) Sand cast iron S&S as per IS - 3989

Providing and fixing terminal guard : 100mm (b) Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

Providing and fixing collar : 100 mm (a) Sand cast iron S&S as per IS - 3989

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 (a) 15mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour : Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms

Providing and fixing CP brass 32mm size bottle trap of approved quality and make and as per the directions of Engineer-in-charge.

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes, weighing not less than 60 gms

Providing and fixing PTMT urinal cock of approved quality and colour : 15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads weighing not less than 48 gms

Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe. : Total bracket length 580 mm of approved shape and design (for single 100 mm dia pipe)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. (a) 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. (b) 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.: External Work (a) 25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. (b) 32 mm nominal dia Pipes

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. : 15 mm nominal bore

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore

Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329 : 100 mm dia Ductile Iron Class K-9 pipes

Providing and fixing PVC trap of self cleansing design with CP brass grating with or without vent arm complete including cost of cutting and making good the walls & floors. 100mm inlet and 75 outlet

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250 mm diameter

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : (a) 150 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : (b) 250 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : (c) 300 mm dia. R.C.C. pipe

Providing and fixing C.P. brass double coat hook, conforming to IS 8931. (approved make )

Providing and fixing square-mouth S.W. gully trap grade 'A'’ complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : (a) 100x100 mm size P type (i) With F.P.S. Bricks class designation 35

Providing and fixing uplasticised PVC connection pipe with brass unions : (a) 15 mm nominal bore with 45cm length.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : (a) 20 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 100 mm diameter

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : (a) Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With Sewer bricks conforming to IS : 4885

Extra for depth for manholes : Size 120x90 cm With Sewer bricks conforming to IS : 4885

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar

Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal grating with frame and vertical grating complete as per standard design : (a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: (a) Inside dimensions 455x610 mm and 45 cm deep for single pipe line : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. (a) With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (a) 100 mm diameter

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (b) 150 mm diameter

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (c) 250 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : (a) 100 mm diameter S.W. pipe

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (b) 150 mm diameter S.W. pipe

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (c) 250 mm diameter S.W. pipe

Tubewells Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. (a) All types of soil - 300 mm dia

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. (b) Rocky strata including Boulders - 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. (a) 200 mm nominal size dia

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. - 150 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). - 150 mm dia

Providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear meter (expansive nature) for construction joints treatment of RCC structure such as raft slab, retaining walls, water storage tank and at the junctions of raft slab with the retaining walls etc.. After cleaning the surface, one coat of required primer for swellable water stop tape shall be applied throughout the length of the joint @3.78 litre per 240 running meter. Over the primed surface swellable type water stop tape shall be placed. The work shall be carried out all complete as per specification and the direction of the Engineer-In-Charge. The product performance shall carry guarantee for 10 years against any leakage.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc (a) 50 mm dia nominal bore

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (b) 65 mm dia nominal bore

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (c) 80 mm dia nominal bore

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. (a) All types of soil (i) 300 mm dia

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : (b) Rocky strata including Boulders (i) 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. (a) 150 mm nominal size dia having minimum wall thickness 5.00 mm

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. (a) 150 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maxi mum rate of useable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, including disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50mm x 1.6 mm complete, all as per direction of Engineer-in-charge.

KITCHEN CUPBOARD Providing and fixing 6mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge.

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc with auto closing spring loaded hinges (hydraulic type) etc complete as per direction of Engineer-in-Charge (payment for providing and fixing auto closing hinges shall be paid separately) (For Cupboard Front)

Providing M.S. Piano hinges ISI marked IS : 3818 finished with nickel plating and fixing with necessary screws etc. complete: Overall width 50 mm. (For Cupboard)

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 100x10 mm. (For Cupboard)

Providing and fixing magnetic catcher in cupboard / ward robe shutters including fixing with necessary screws etc. complete (Best make of approved quality): Double strip (horizontal type). (For Cupboard)

Providing and fixing special quality chromium plated brass cupboard locks with six levers including necessary screws etc. complete (Best make of approved quality) of : Size 50 mm. (For Cupboard)

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : Kiln seasoned and chemically treated hollock wood - 50x12 mm. (For Cupboard)

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately) :18 mm thick

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain white color board for backing of cup boards and bathroom/kitchen cabinets etc. of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel screws etc. all as per direction of Engineer-InCharge. (Note: stainless steel screws shall be paid separately) : 12 mm thick

Providing and fixing factory made 18 mm thick single extruded WPC (Wood Polymer Composite) solid plain white colour board Jali, CNC (Computer numeric control) routed of approved design by Engineer-in-charge which are machine cut for duct/shaft covering, partitions and facades comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium corbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with properties of being termite/borer proof, water/ moisture proof and fire retardant and fixing on M.S (mild steel) frame made of 25 x 25 x 1.5 mm square hollow box section including applying a priming coat of approved steel primer, placed at grid made at 1.0 x 1.0 m or as per requirement at site with necessary stainless steel fasteners and SS screws etc., all complete as per direction of Engineer-In- Charge. (Note: M.S (mild steel) framework with priming coat and necessary SS fasteners and SS screws shall be paid separately.

Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. : 10 x 120 mm

Providing and Fixing Wall Paneling with Leather Coulting nailed on 12 mm thk. Commercial Plywood with one side waterproof coating fixed with wall.

WPC Wall Paneling: Providing and fixing WPC paneling, the faming shall consist of aluminum tube sections 50mmx50mm @ 600mm c/c Both ways horizontally and vertically on the column/wall. The cavity of framework should be inserted with Resin Bonded Rockwool conforming to IS 8183, density 48 kg/m3, 50mm thick.The framing would be covered with wooden finish, perpolished, 100% non-tocixm non-formaldehyde, environmental friendly WPC/ Charcoal convoluted panels alternative box and flat section fixed on 12mm thick BWP ply/MDF fixed with stainless steel screws.The wooden surface will be covered with designer teak wood moulding of 50x25mm as per approved design and finished with Melamine polish. All completes as per Architect and direction of Engineer-in-Charge

Wooden Wall Paneling: Providing and fixing wall paneling, the faming shall consist of aluminum tube sections 50mmx50mm @ 600mm c/c Both ways horizontally and vertically on the column/wall. This framing would be covered with 12mm thick BWP Ply of approved Make Marion/ Century/ Green or equivalent. The BWP ply to be finished with 4 mm thick veneer of approved (Make- Century/Merino and making provision for opening for door, windows, electrical conduits, switch boards etc, including of inlay work with 12x12mm Bronze/Gold SS Strip with teak wood moulding of 50x25mm as per approved design and finished with Melamine polish. All completes as per direction Engineer-in-Charge

Wall Paper: Provide & laying of wall covering PVC coated with woven cotton OR woven Polyester washable wall paper with inlay work on finished surface i.e. on ceiling or wall. The base shall be make, flat, firm, dry, free of dust, suitable for wall paper application, grease and of uniform color made up of surfaces. Wall covering to be applied to the base with approved make of adhessive of approved Make and DeSign as per architect and the directions of (Make: Trusardi or italian)

Providing and fixing wooden blinds 50 mm basswood slat width horizontal strips with neccessary fixing arrangement with siper soft cord operating mechanism, aluminium had rail complete as per direction of Engineer-in-charge

Acoustic Wall Paneling: Providing and fixing Acoustical panels of 9mm thickness with square I beveled edge manufactured from 100% Polyethylene Terephthalate (PET) having density of >100 ( the panel WITH 60% recycled content) , Kgs/m3, fire resistant as per B1 Class A. The faming shall consist of aluminum tube sections 50mmx50mm @ 600mm c/c Both ways horizontally and vertically on the column/wall. The cavity of framework should be inserted with Resin Bonded Rockwool conforming to IS 8183, density 48 kg/m3, 50mm thick.The framing would be covered with 12mm thick BWP ply/MDF fixed with stainless steel screws.The panels to be further glued to the ply with SH/SR adhesive. The wooden surface will be covered with designer teak wood moulding of 50x25mm as per approved design and finished with Melamine polish. All completes as per Architect and direction of Engineer-in-Charge

Providing and fixing in wall lining medium density fibre board IS: 14587:1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete. :18 mm thick.

Providing and fixing skirting with Pre-laminated medium density fibre board exterior grade (Grade-I) conforming to IS: 14587:1998 marked, with (one side decorative and other side balancing lamination and edges to be sealed with PVC edge bending tape 2.00 mm thick of approved brand with necessary fixing arrangements and screws, including drilling necessary holes for rawl plugs etc. all complete. :18 mm thick.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. (a) 1.5 mm thick

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. (b) 1.0 mm thick

Providing and fixing storage wooden cabinets below kitchen counter comprising of external frame work of 2nd class teak wood 50x50mm frame work, carus with 19mm thick BWP type blcok board confirming partitions, over all depth 550mm two number horizontal partitions of the same block board, providing 1mm thick PVC edge band on all exposed edges of blcok board, providing shutter with block board with 75mm thick plain 75x45x2 mm thick S.S. Grade 304 butt hinges to each shutter leaf, inside exposed edge to be furnished with 0.8mm laminates of approved brand and shed door shutter lamination with 1mm thick decorative laminates as per direction of Engineer-in-charge and shop drawing complete. The front elevatin of the cabinet shall be measured in sqm for payment.

Providing, fabricating and fixing on wall with S.S dash fastner 100x10 mm sizes of wooden cabinets 350mm deep, fabricated frame work of required sizes in width and height with 19mm thick block board confirming to IS. 1659BWP type with edge lippling on all exposed edge 1mm thick PVC band fixed with adhesive SR-998 of pidilite or equivalent, backside 12mm thick commercial ply confirm to IS 303 BWR grade intermediate shelves 3no. inside & furnishing internal all surfaces with 0.7mm thick plain laminates of approved colour, external surfaces with 1mm thick pressure laminate of approved brand and manufacture, 3 number doule acting hydraulic S.S. hinges of Godre, EBCO heitich or equivalent to each shutters, decorative S.S. handles 150mm long on each shutters, complete work including all inputs of material labour and T&P etc. as per direction of Engineer-in-charge (Elevation area shall be measured for payment in Sqm).

Providing, fabricating and placing wooden cabinets / storage units of customized sizes wide 900, Depth 600mm, Height 2400mm fabricated of 19mm thick block board BWP type confirming to IS1659, backing with 12mm thick ply confirming to IS:710, including strengthening of the bottom support of horizontal partitions with alround band of 19mm thick block board 75mm wide strip fixed with adhesive and nails before fixing to frame, double leaf shutters of 19mm thick block board fixed with double acting spring hinges of approved brand and manufacturer including finishing the exposed faces except back and bottom with 1mm thick decorative laminates, of approved brand and manufacturer, plain laminates inside the all surfaces, back and bottom faces to be finished with synthetic enamel paint over approved quality pink wood primer, all edges of board frame and shutter to be provided with edge band of 1mm thick PVC of matching colour fixed hot pressed with adhesive like heatex of pidilite, or bondtite of astral etc all complete as per drawing and direction of Engineer-in-charge. (Elevation area in sqm. shall be measured for parment)

ROAD WORK & FOOTPATH Construction of granular sub-base 200mm thick by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. : With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer in-charge.

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, levelling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately. (a) 150mm thick Cement concrete manufactured in automatic batching plant (RMC plant) i/c transportation to site in transit mixer

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Providing and fixing Glow studs of size 100x20 mm made of heavy duty body shall be moulded ASA (Acrylic styrene Acryloretrite ) or HIP (High impact polystyrene) or ABS having electronically welded micro- prismatic lens with abrasion resistant coating as approved by Engineer in charge. The glow stud shall support a load of 13635 kg tested in accordance with ASTM D4280. The slope of retro- reflective surface shall be 35 (+/-5) degress to base .The reflective panels on both sides with at least 12 cm of reflective area up each side. The luminance intensity should be as per the specification and shall be tested as described in ASTM I: 809 as recommended in BS: 873 part 4 : 1973. The studs shall be fixed to the Road surface using the adhesive conforming to IS, as per procedure recommended by the manufacturer complete and as per direction of Engineer-in-charge.

Providing and applying 2.5 mm thick road marking strips (retro reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. (a) 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern

Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. : Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade

Supplying and stacking at site - of good earth - for building area filling etc. brought from outside approved borrow areas for all leads lifts and carried by mechanical transport including loading, unloading & royalty & including banking/filling earth in layers not exceeding 20cm in depth, breaking clods, watering, consolidating each deposited layer by ramming and watering, all complete as per specifications and directions of Engineer in Charge. Borrow area shall be arranged by Contractor at his own cost.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge)

Finishing walls with water proofing cement paint of required shade : (a) New work (Two or more coats applied @ 3.84 kg/10 sqm)

ARBORICULTURE Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be reduced by 8% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 4.75 mm

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Digging holes in ordinary soil and refilling the same with the excavatedearth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts ofstacked volume of earth after reduction by 20% : 1 part of stacked volumeof manure after reduction by 8%) flooding with water, dressing includingremoval of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : (a) Holes 1.2 m dia and 1.2 m deep

Digging holes in ordinary soil and refilling the same with the excavatedearth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts ofstacked volume of earth after reduction by 20% : 1 part of stacked volumeof manure after reduction by 8%) flooding with water, dressing includingremoval of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : (b) Holes 0.90 m dia and 0.90m deep

Providing and stacking of Bauhinia blakeana (Kachnar) plant of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and displaying of Areca Palm plant , having ht. 1.80 m to 2.10 m with 8 to 10 suckers, well developed, fresh and healthy with lush green foliage in 30 cm size of Earthen pot / Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Dracaena song of India specimen (three in one), having ht. 60 cm & above, well developed, fresh and healthy with good foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water) : Trees Plant

Complete maintenance of trees, jobs like making of basin at regular interval,application of fertilizer etc, (excluding the cost of material which shall be supplied by the department and other T & P material/articles shall be provided by the contractor) as per direction of officer in charge for 6 months after the completion of the project Trees for 250 no/(up to 4 & up to 3 year Slow & Fast growing Per tree group)

Providing and applying anti termite treatment of infected trees i/c all branches/ leaves by spraying chemical emulsion 0.5% (Chlorpyriphos 20% EC) concentration through power spray machine (@ 100 ml Chlorpyriphos per tree i/c cost of chemical) and as per direction of officer-in-charge.and as per direction of officer-in-charge.

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge.

Electrical Works Wiring of Light/Fan/Call Bell/Exhaust Fan/Ceiling Fan-Transit Suite (Indoor) Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm HR-FRLSH insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc. as required. (a) Group-A

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm HR-FRLSH insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc. as required. (b) Group-B

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm HR-FRLSH insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc. as required. (c) Group-C

Wiring for circuit/ submain wiring along with earth wire with the following sizes of HR-FRLSH insulated copper single core cable in surface/ recessed medium class PVC conduit as required (a) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of HR-FRLSH insulated copper single core cable in surface/ recessed medium class PVC conduit as required (b) 2 X 4.0 sq. mm + 1 X 4.0 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of HR-FRLSH insulated copper single core cable in surface/ recessed medium class PVC conduit as required (c) 2 X 6.0 sq. mm + 1 X 6.0 sq. mm earth wire

Wiring for circuit/ submain wiring along with earth wire with the following sizes of HR-FRLSH insulated copper single core cable in surface/ recessed medium class PVC conduit as required (d) 2 X 10.0 sq. mm + 1 X 10.0 sq. mm earth wire

Luminiaries: Installation, testing and commissioning of pre-wired, fluorescent fitting of all types, with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm HR-FRLSH insulated, copper conductor, single core cable and earthing etc. as required.

Supply & Fixing of Sleek high performance low-height LED downlighter suited for Recessed Type Fittings. (a) Power Consumption 10 W, Correlated Color Temperature (Nom) 6500 K, Luminous Flux 1000 lm, Luminous Efficacy (rated) (Nom) 110 lm/W Color rendering index (CRI) >80, Beam angle of light source 120 degree(s), Optic type Beam angle 120°, Ingress protection code IP20 [Finger-protected], Mech. impact protection code IK02 [0.2 J standard], Surge Protection (Common/Differential) Surge protection level until 2.5 kV, Protection class IEC Safety class I

Supply & Fixing of Sleek is a high performance low-height LED downlighter suited for Recessed Type Fittings. (b) Power Consumption 15 W, Correlated Color Temperature (Nom) 6500 K, Luminous Flux 1000 lm, Luminous Efficacy (rated) (Nom) 110 lm/W Color rendering index (CRI) >80, Beam angle of light source 120 degree(s), Optic type Beam angle 120°, Ingress protection code IP20 [Finger-protected], Mech. impact protection code IK02 [0.2 J standard], Surge Protection (Common/Differential) Surge protection level until 2.5 kV, Protection class IEC Safety class I

Supply & Fixing of Sleek Surface Downlight Slim profile surface mounted downlight with options of 1000 lumen. (a) Power Consumption 12 W, Correlated Color Temperature (Nom) 6500 K, Luminous Flux 1000 lm, Luminous Efficacy (rated) (Nom) 110 lm/W Color rendering index (CRI) >80, Beam angle of light source 120 degree(s), Optic type Beam angle 120°, Ingress protection code IP20 [Finger-protected], Mech. impact protection code IK02 [0.2 J standard], Surge Protection (Common/Differential) Surge protection level until 2.5 kV, Protection class IEC Safety class I

Supply & Fixing of Sleek Surface Downlight Slim profile surface mounted downlight with options of 1000 lumen. (b) Power Consumption 15 W, Correlated Color Temperature (Nom) 6500 K, Luminous Flux 1000 lm, Luminous Efficacy (rated) (Nom) 110 lm/W Color rendering index (CRI) >80, Beam angle of light source 120 degree(s), Optic type Beam angle 120°, Ingress protection code IP20 [Finger-protected], Mech. impact protection code IK02 [0.2 J standard], Surge Protection (Common/Differential) Surge protection level until 2.5 kV, Protection class IEC Safety class I

Supply & Fixing of Sleek Surface Downlight Slim profile surface mounted downlight with options of 1000 lumen. (c) Power Consumption 20 W, Correlated Color Temperature (Nom) 6500 K, Luminous Flux 1000 lm, Luminous Efficacy (rated) (Nom) 110 lm/W Color rendering index (CRI) >80, Beam angle of light source 120 degree(s), Optic type Beam angle 120°, Ingress protection code IP20 [Finger-protected], Mech. impact protection code IK02 [0.2 J standard], Surge Protection (Common/Differential) Surge protection level until 2.5 kV, Protection class IEC Safety class I

Supply & Fixing of Sleek Surface type downlights with bold and elegant metal delivers perfect balance of good design with high energy efficiency and solution for general indoor area lighting. (a) Power Consumption 18 W, Correlated Color Temperature (Nom) 4000 K, Luminous Flux 1000 lm, Luminous Efficacy (rated) (Nom) 110 lm/W Color rendering index (CRI) >80, Beam angle of light source 120 degree(s), Optic type Beam angle 120°, Ingress protection code IP20 [Finger-protected], Mech. impact protection code IK02 [0.2 J standard], Surge Protection (Common/Differential) Surge protection level until 2.5 kV, Protection class IEC Safety class I

Supply & Fixing of Consistent Chrome finish for uniform shine includeing 1 no Wall Light for 3 Watt, Holder Type - B-22, IP-20 rated,Class of Protection - I

Supply, fixing, testing and commissioning of Post Top fitting complete with 26 watt LED luminaries along with required Driver. Power Consumption 26 W, Correlated Color Temperature (Nom) 4000 K, Symmetric wide beam, Luminous Efficacy (rated) (Nom) 100 lm/W Color rendering index (CRI) >70, Optic type outdoor Distribution Symmetric Wide, Mounting device - Spigot for diameter 60 to 76 mm, IP65, Mech. impact protection code IK07, Surge Protection (Common/Differential) 4/4 kV, Protection class IEC Safety class I

Ceiling Fan: Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30cm) with 1.5 sqmm HR-FRLS insulated copper conductor, single core cable etc.

Supply of 1200mm sweep BLDC ceiling fan suitable for operation on 230V, 50 Hz AC supply, complete with down rod, rubber shackle, blades, condensor, canopies etc. complete as reauired but without regulator.

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. (Two module)

Wall Mounting Fan: Supply of 400 mm sweep Wall Mounting fan suitable for operation on 230V, 50 Hz AC supply, complete with Fixing Arrangement, blades, condensor, Inbuild regulator etc. complete as required.

Exhaust Fan: Installation, testing and commissioning of Exhaust fan, including wiring with 1.5 sqmm HR-FRLSH insulated copper conductor, single core cable etc.

Supply of single phase, 250 mm sweep, 1400 rpm exhaust fan suitable for operation on 230V, 50 Hz AC supply, complete with blades, condensor, frame etc. as required.

Supply of single phase, 450mm sweep, 1400rpm Industrial grade exhaust fan suitable for operation on 230V, 50 Hz AC supply, complete with blades, condensor, frame etc. as required.

Extra for fixing the louvers / shutters complete with frame for exhaust fan.

Call Bell/Buzzer: Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

Wiring of Light & power Plug Socket Outlet - Transit Suite (Indoor) Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 5/6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying, fixing, testing & commissioning of following size/ modules, Gl box along with modular base & cover plate for modular switches in recess etc. as required. (a) 1/2 Module (75mm X 75mm)

Supplying, fixing, testing & commissioning of following size/ modules, Gl box along with modular base & cover plate for modular switches in recess etc. as required. (b) 3 Module (100mm X 75mm)

Supplying, fixing, testing & commissioning of following size/ modules, Gl box along with modular base & cover plate for modular switches in recess etc. as required. (c) 4 Module (125mm X 75mm)

Supply & Fixing of 250 Volt, 4 Ft. long 2100lm 18 Watt Single LED Tube Light fittings complete with all accessories incl. LED Tube. Flicker free, high efficiency and robust industrial batten family suitable for surface, wall and conduit mounting.

Supply, fixing, testing and commissioning of integral flood (bracket light) fitting complete with 60 watt LED luminaries along with required Driver. Power Consumption 60 W, Correlated Color Temperature (Nom) 5700 K, Luminous Flux 8400 lm, Luminous Efficacy (rated) (Nom) 140 lm/W Color rendering index (CRI) >70, Luminaire light beam spread 130° x 88°, Optic type outdoor Distribution Symmetric Wide, Mounting device - Spigot for diameter 60 to 76 mm, IP66 [Dust penetration-protected, jet-proof], Mech. impact protection code IK10 [20 J vandal-resistant], Surge Protection (Common/Differential) 4/4 kV, Protection class IEC Safety class I

Water Cooler: Supply, erection, testing and commissioning of water cooler of cooling capacity 40 litre per hour, storage capacity 80 litre.

Supply, erection, testing & commissioning of 5 kVA single phase voltage stabiliser with working voltage 150 to 290 volt having low voltage cut off below 150 volt, high voltage cut off above 300 volt and time delay.

EPABX System: Supply Installation Testing & Commissioning of MITEL- Unify EPABX System complete with OpenScape Business x-5w UC Enabled IP Ready Voice Switch,,  Integrated IP Gateway for IP extension and ITSP’s  Integrated UC on motherboard  Expandable up to 512 users  Booster Server / S Software  DSP Resources built in (TDM to IP and Vice versa)  8 Party Conference  Auto Attendent  DECT Compatible  Q-Sig Compatible  SIP Compatible  Remote maintenance  CLI on Analog/Digital/IP/Trunks. Currently Equipped for: HARDWARE & SOFTWARE including LICENSECES for SYSTEM and following items: 1. Trunk- 08 Nos 2. Digital Extentions- 08 Nos 3. IP User Extentions-05 4. Analog Extentions-52 All UC Applications Hardware Inbuilt

Supply Installation Testing & Commissioning of Unify DIGITAL Phone OpenScape CP 400T complete with  3 Line Graphical display monochrome (Non Tiltable)  Hands- Free (Full Duplex)  Full HD Voice  3 Fixed Function keys with LED  16 Freely programmable keys  3 Navigations Keys with control Keys +/-

Supply Installation Testing & Commissioning of Unify Openscape CP 110 Phone Having Display- 03 line Fixed Keys -03 Keys Optical Call Alert, Mute, Hands free, Loud speaker, Volume Control

INFRASTRUCTURE FOR COMMUNICATION NETWORK for Complete Premesis Supply and fixing of MDF with Krones and connecting Cable

Supply & fixing of UPS for Power Backup for 30 Minutes

Supply & fixing of Analog Phone Signtel SL 910

Supplying & drawing of following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmoured telephone cable in existing Conduit all complete. (a) 2 pair

Supply & fixing of Modular Type Telephone ( RJ -11 ) outlet with GI box complete wirh Modular Cover plate

Peripheral Lighting & illumination Supply, fixing, testing and commissioning of integral flood (bracket light) fitting complete with 60 watt LED luminaries along with required Driver. Power Consumption 60 W, Correlated Color Temperature (Nom) 5700 K, Luminous Flux 8400 lm, Luminous Efficacy (rated) (Nom) 140 lm/W Color rendering index (CRI) >70, Luminaire light beam spread 130° x 88°, Optic type outdoor Distribution Symmetric Wide, Mounting device - Spigot for diameter 60 to 76 mm, IP66 [Dust penetration-protected, jet-proof], Mech. impact protection code IK10 [20 J vandal-resistant], Surge Protection (Common/Differential) 4/4 kV, Protection class IEC Safety class I

Supply, fixing, testing and commissioning of Post Top fitting complete with 26 watt LED luminaries along with required Driver. Power Consumption 26 W, Correlated Color Temperature (Nom) 4000 K, Symmetric wide beam, Luminous Efficacy (rated) (Nom) 100 lm/W Color rendering index (CRI) >70, Optic type outdoor Distribution Symmetric Wide, Mounting device - Spigot for diameter 60 to 76 mm, IP65, Mech. impact protection code IK07, Surge Protection (Common/Differential) 4/4 kV, Protection class IEC Safety class I

Supply, erection, testing & commissioning of 6 mtr long Octagonal Pole, (200X200)x12 mm thick base plate, complete with 1 Mtr long single arm bracket. Pole is comprising with pole box arrangement consisting with 1 no 6A DP MCB 'C' curve of 10kA rated and pole earthing provision in the base plate and complete.

Supply, erection, testing & commissioning of 6 mtr long Octagonal Pole, (200X200)X12 mm thick base plate, complete with 2 no 1 Mtr long double arm bracket. Pole is comprising with pole box arrangement consisting with 1 no 6A DP MCB 'C' curve of 10kA rated and pole earthing provision in the base plate and complete.

Supply, erection, testing & commissioning of 4 mtr long Octagonal Pole, (200X200)X12 mm thick base plate. Pole is comprising with pole box arrangement consisting with 1 no 6A DP MCB 'C' curve of 10kA rated and pole earthing provision in the base plate and complete.

Excavation, Shuttering & Foundation for Streel Light Octagonal pole by RCC of M-25 grade concrete with foundation bolt (Supplied along with Street Light Octagonal Pole by Pole manufacturer) and backfilling the remain excavation area beside the Foundation.

Supply and connection of (2x1.5+1x1.5) sqmm HR-FRLSH type flexible copper conductor for internal connection of luminaries from Pole box (junction Box inside the pole) to luminaris.

Supply of 1.1 kV grade, XLPE insulated, armoured, PVC outer sheath aluminium cable of following sizes. (a) 4 C X16 sq mm

Laying of one number XLPE power cable of 1.1 KV grade of following size direct in ground but excluding sand cushioning and protective covering (a) Upto 35 sq mm

Laying of one number XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL/HDPE pipe as required. (a) Upto 35 sq mm

Providing, laying following outer dia HDPE pipe of PE 100 grade, SDR - 17, PN - 8 in ground as required (a) 40 mm dia

Laying of following size cable in the existing masonary duct as required (a) Upto 35 sq mm

Laying and fixing of one number XLPE power cable of 1.1 KV grade of following size on wall surface as required. (a) Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number XLPE power cable of 1.1 KV grade of following size on cable tray as required. (a) Upto 35 sq. mm (clamped with 1mm thick saddle)

Supply & installing of 300 mm width X 62.5 mm depth X 2.0 mm thickness perforated pre-painted MS cable trays with perforation not more than 17.5 % in convenient sections, joint with connectors, suspended from the ceiling with MS suspenders including bolts and nuts, painting suspenders as required

Supplying and installing of 300 mm width X 62.5 mm depth X 2.0 mm thickness perforated pre-painted M.S. cable tray bends with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S.suspenders including bolts & nuts, painting suspenders etc as required.

Supplying and installing of 300 mm width X 62.5 mm depth X 2.0 mm thickness perforated pre-painted M.S. cable trays Tee’s with perforation not more than 17.5%,joined with connectors, suspended from the ceiling with M.S.suspenders including bolts & nuts, painting suspenders etc asrequired.

Supplying and making indoor end termination with brass compression gland and aluminium lugs for following size of XLPE aluminium conductor cable of 1.1 KV grade as required. (a) 1.0 C X 300 sq mm

Supplying and making indoor end termination with brass compression gland and aluminium lugs for following size of XLPE aluminium conductor cable of 1.1 KV grade as required. (b) 3.5 C X 120 sq mm

Supplying and making indoor end termination with brass compression gland and aluminium lugs for following size of XLPE aluminium conductor cable of 1.1 KV grade as required. (c) 3.5 C X 95 sq mm

Supplying and making indoor end termination with brass compression gland and aluminium lugs for following size of XLPE aluminium conductor cable of 1.1 KV grade as required. (d) 3.5 C X 70 sq mm

Supplying and making indoor end termination with brass compression gland and aluminium lugs for following size of XLPE aluminium conductor cable of 1.1 KV grade as required. (e) 3.5 C X 50 sq mm

Supplying and making indoor end termination with brass compression gland and aluminium lugs for following size of XLPE aluminium conductor cable of 1.1 KV grade as required. (f) 3.5 C X 35 sq mm

Supplying and making indoor end termination with brass compression gland and aluminium lugs for following size of XLPE aluminium conductor cable of 1.1 KV grade as required. (g) 3.5 C X 25 sq mm

Supplying and making indoor end termination with brass compression gland and aluminium lugs for following size of XLPE aluminium conductor cable of 1.1 KV grade as required. (h) 4 C X16 sq mm

Earthing Arrangement: Supply & earthing with G.I earth pipe 4.5 metre long, 40mm dia including accessories, and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal/coak and salt as required.

Providing and fixing earth bus of 25 mm X 5 mm GI strip on surface for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/recessed conduit/submain wiring/ cable as required.

Distribution Board Supply and fixing of the following ways prewired TP&N MCB distribution board of sheet steel for 415 volts, on surface/ recess complete with loose wire box, terminal connectors for all incoming and out going circuits, duly prewired with suitable size HR-FRLSH insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB / RCCB/ Isolator) (a) 4 way (4 + 12), Double door

Supply and fixing of the following ways prewired TP&N MCB distribution board of sheet steel for 415 volts, on surface/ recess complete with loose wire box, terminal connectors for all incoming and out going circuits, duly prewired with suitable size HR-FRLSH insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.(But without MCB / RCCB/ Isolator) (b) 8 way (4 + 24), Double door

Supplying and fixing following rating, four pole, 415 volts, C curve MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) 40 Amps

Supplying and fixing following rating, four pole, 415 volts, C curve MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required. (b) 63 Amps

Supply and fixing of 5A to 32A rating, 240/415 volts, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) Single pole

Supply and fixing of 5A to 32A rating, 240/415 volts, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (b) Single pole and Neutral

Supply and fixing of 5A to 32A rating, 240/415 volts, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (c) Double pole

Supply and fixing of 5A to 32A rating, 240/415 volts, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (d) Triple pole

Supply and fixing of 5A to 32A rating, 240/415 volts, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (e) Triple pole & Neutral

Electrical HT Substation & Swichgear: Transformer Supply, installing, testing and commissioning of outdoor type plinth mounted step down transformer, 11 KV/433 Volts (at no load) AC 3 phase 50 Hz, 630 KVA capacity, core type, double copper wound, oil immersed, naturally cooled, Oil Natural-Air Natural (ON AN), with external cooling tubes, delta connected on primary side (HV) and star connected on secondary side (LV) in accordance with vector group DYn-11, Neutral brought out on secondary side (LV side) and having tapings at -7.5% to 7.5% on HV side and to be changed by means of hand operated off load tap changer gear. The maximum temperature rise should not exceed 45 degree celsius in oil and 55 degree celsius in HV/LV winding when measured by resistance method after continuous full load run on an ambient temp of 40 degree celsius. The transformer shall be conforming to EEL-2 as per IS-1180 (Part - I) 2014 with latest ammendment 1,2,3 & 4 having total losses as per EEL -2 and shall comprise of the following:- (a) One cable box on HT side (primary side) consisting of three nos porcelain bushing with copper rods, complete with nuts and washers, with cable glands (b) One cable box on LT side (Secondary side) consisting of four nos porcelain bushing with copper rods, complete with nuts and washers, with cable glands (c) Oil conservator with drain valve and oil level guage. (d) De-hydrating breather with first fill of dehydrating agent (silica gel). (e) Exhaust vent, air release valve, Thermometer pocket on tank cover, Lifting lugs, Oil filling hole with cap / plug and four nos plain solid cast iron detachable rollers. (f) One no 100 mm dia, dial type thermometer, vapour pressure type, having range 0-120 degree celsius with metal guard having maximum perimeter temperature reading indicator with re-setting device. (g) Two earthing terminals on tank cover for earthing of body. (h) Name, Rating and diagram plate. (j) Extra bushing for neutral, in the LT cable box for providing independent set of earthing for (k) First fill of new transformer oil, IS-335 marked, filtered and tested upto 55 KV dielectric strength (l) Providing adequate size and nos of channels, embeded in floor, for movement of transformer.

HT Switchgear Supplying, installing, testing and commissioning of Indoor arc flash protected Draw-Out with roll on floor type Vacuum Circuit Breaker Panel , rated for 11kV, 800Amp, 26.3kA/3-sec, comprising of 1 No. ICOG VCB Panels confirming to IEC 62271-200, Internal Arc Classified IAC AFLR 26.3kA for 1sec, Accessibility Class LSC2B-PM Class, comprising of 800Amp, continuous rated Copper busbars and droppers, 02 Nos . Rack-In-Rack-Out Handles, structure made from AluZinc/GI sheets to prevent corrosion and rusting. The complete panel including HT and LT chamber with FRLS wiring shall be manufactured by approved OEM at its own facility, and same will be verified via stage/final inspection. Make ABB/Seimens/Schneider The Board shall consist of following panels:- Contd..... (A) 01 X ICOG Panel, each comprising of :- (i) 11kV, 800Amp, 26.3KA/3-sec, Draw-Out Vacuum Circuit Breaker as per IEC-62271-100. Vacuum Circuit Breaker having 03nos. vacuum bottles of same make as of circuit breaker, motorized spring charging mechanism (230VAC) with integral spring charging handle for manual charging, associated push-buttons, anti-pumping feature, and associated Shunt Trip/Close Coils (110VDC). (ii) Current Transformers 11kV, 200-100/1-1, Core1: Class 5P10, 2.5VA, Core2: Class 0.5, 2.5VA - Set of 03 Nos. Contd..... (iii) Main Protection Relay shall be numerical IED Relay confirming to IEC60255, having 04CT Inputs with microprocessor based protection scheme for tripping the breaker on various faults like (a) over-current or earth-fault in any of the three phases, (b) circuit-breaker-failure alarm, (c) interpanel tripping/blocking signals via GOOSE based peer-to-peer communication, on IEC61850 protocol. (d) Integrted arc flash protection with current and light sensing The relay shall be communicable on IEC 61850 GOOSE platform over RJ-45/USB/FO port, and fully integrated with the feeder, internally capturing feeder statuses incl. various status, Line-Current, Breaker On/Off/Spring.Chrgd, Trip Circuit Failure (from TCS relay), Local-Remote etc. and display locally on a built-in back-lit LCD screen with mimic as a Single-Line-Diagram with current measurements and suitably labelled status LEDs. Relay setting should be possible through inbuilt software or through addtional software supplied by the relay manufacturer. (iv) Metering Equipment including:- (a) 01 x Digital Ammeter (Acc.Cl.0.5) (v) LED Indications - (a) Breaker ON/OFF/TRIP/Spring-Charged, (b) Trip Circuit Healthy Contd...... (vi) 04-Window Annunciator with Hooter to indicate following alarms :- (a) OC Trip, (b) EF Trip (c) Trip Circuit Failure, (d) Inter-Tripping Fault, The Annunciator will be complete with required Acknowledge/Test buttons as required (vii) Control Equipment incl. (a) 01 x TNC Switch, (b) 01 x Emergency Trip Push Button, (c) 01 x Local/Remote Switch, (d) MCBs for AC/DC isolation (e) Heater Switch with Thermostat - 01no. (f) 3-pin socket with ON/OFF switch - 01no. (g) CFL Lamp with ON/OFF switch - 01no. (viii) Flush mounted Auxillary Protection Relays incl. (a) Trip Circuit Supervision Relay, (b) Master trip Relay,

Battery for Switchgear Design,Supply, installation, testing and commissioning of Automatic float cum Boost Battery Charger with DCDB suitable for Ni-Cd battery bank of suitable Ah capacity at 110 Volt complete in all respect. .

Control Wiring - Transformer Supply & Laying of 1.1 kV, 16 C, 2.5 sq mm PVC insulated & PVC round sheathed flexible industrial Cu control cable for laying from transformer marshalling box to HT panel.

Supply & Laying of 1.1 kV, 2 C, 2.5 sq mm PVC insulated & PVC round sheathed flexible industrial Cu control cable for laying from transformer marshalling box to HT panel.

Transformer Earthing Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

HT CABLE WORK Supply of 3 core, 185 sqmm, 11 kV(E), XLPE insulated, PVC inner & outer sheath, round armoured, aluminium cable as per Cable Code: A2XFY/2XFY and Specification as per IS: IS 7098 Part-2

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11KV grade of following size direct in ground including excavation, sand cushioning, protective covering with bricks and refilling the trench etc as required. (a) Above 120 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering with bricks and refilling the trench etc as required. (a) Above 120 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METALpipe as required. (a) Above 120 sq. mm and upto 400 sq. Mm

Providing, laying following outer dia HDPE pipe of PE 100 grade, SDR - 17, PN - 8 in ground as required (a) 90 mm dia

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11KV grade of following size in the existing masonry openduct as required. (a) Above 120 sq. mm and upto 400 sq. Mm

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable forfollowing size of 3 core, XLPEaluminium conductor cable of 11 KV grade as required : (a) 240 sq. mm

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable forfollowing size of 3 core, XLPEaluminium conductor cable of 11 KV grade as required : (a) 240 sq. mm

Supplying and making straight through cable jointing with heat shrinkable jointing kit complete with all accessories including ferrules suitable for following size of 3 Core, XLPEaluminium conductor cable of 11 KV grade as required : (a) 240 sq. mm

Cabling Work: Supply of 1.1 kV grade, XLPE insulated, armoured, PVC outer sheath aluminium cable of following sizes. (a) 1.0 C X 300 sq mm

Supply of 1.1 kV grade, XLPE insulated, armoured, PVC outer sheath aluminium cable of following sizes. (b) 3.5 C X 120 sq mm

Supply of 1.1 kV grade, XLPE insulated, armoured, PVC outer sheath aluminium cable of following sizes. (c) 3.5 C X 95 sq mm

Supply of 1.1 kV grade, XLPE insulated, armoured, PVC outer sheath aluminium cable of following sizes. (d) 3.5 C X 70 sq mm

Supply of 1.1 kV grade, XLPE insulated, armoured, PVC outer sheath aluminium cable of following sizes. (e) 3.5 C X 50 sq mm

Supply of 1.1 kV grade, XLPE insulated, armoured, PVC outer sheath aluminium cable of following sizes. (f) 3.5 C X 35 sq mm

Supply of 1.1 kV grade, XLPE insulated, armoured, PVC outer sheath aluminium cable of following sizes. (g) 3.5 C X 25 sq mm

Supply of 1.1 kV grade, XLPE insulated, armoured, PVC outer sheath aluminium cable of following sizes. (h) 4 C X16 sq mm

Laying of one number XLPE power cable of 1.1 KV grade of following size direct in ground but excluding sand cushioning and protective covering (a) Upto 35 sq mm

Laying of one number XLPE power cable of 1.1 KV grade of following size direct in ground but excluding sand cushioning and protective covering (b) Above 35 sq. mm and upto 95 sq. mm

Laying of one number XLPE power cable of 1.1 KV grade of following size direct in ground but excluding sand cushioning and protective covering (c) Above 95 sq. mm and upto 185 sq. mm

Laying of one number XLPE power cable of 1.1 KV grade of following size direct in ground but excluding sand cushioning and protective covering (d) Above 185 sq. mm and upto 400 sq. mm

Laying of one number XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL/HDPE pipe as required. (a) Upto 35 sq mm

Laying of one number XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL/HDPE pipe as required. (b) Above 35 sq. mm and upto 95 sq. mm

Laying of one number XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL/HDPE pipe as required. (c) Above 95 sq. mm and upto 185 sq. mm

Laying of one number XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL/HDPE pipe as required. (d) Above 185 sq. mm and upto 400 sq. mm

Providing, laying following outer dia HDPE pipe of PE 100 grade, SDR - 17, PN - 8 in ground as required (a) 110 mm dia

Providing, laying following outer dia HDPE pipe of PE 100 grade, SDR - 17, PN - 8 in ground as required (b) 90 mm dia

Providing, laying following outer dia HDPE pipe of PE 100 grade, SDR - 17, PN - 8 in ground as required (c) 63 mm dia

Providing, laying following outer dia HDPE pipe of PE 100 grade, SDR - 17, PN - 8 in ground as required (d) 50 mm dia

Providing, laying following outer dia HDPE pipe of PE 100 grade, SDR - 17, PN - 8 in ground as required (e) 40 mm dia

Laying of following size cable in the existing masonary duct as required (a) Upto 35 sq mm

Laying of following size cable in the existing masonary duct as required (b) Above 35 sq. mm and upto 95 sq. mm

Laying of following size cable in the existing masonary duct as required (c) Above 95 sq. mm and upto 185 sq. mm

Laying of following size cable in the existing masonary duct as required (d) Above 185 sq. mm and upto 400 sq. mm

Laying and fixing of one number XLPE power cable of 1.1 KV grade of following size on wall surface as required. (a) Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number XLPE power cable of 1.1 KV grade of following size on wall surface as required. (b) Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Laying and fixing of one number XLPE power cable of 1.1 KV grade of following size on wall surface as required. (c) Above 95 sq. mm and upto 185 sq. mm (clamped with 40x3mm MS flat clamp)

Laying and fixing of one number XLPE power cable of 1.1 KV grade of following size on wall surface as required. (d) Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Lightning Protection System: Providing and fixing of lightning conductor finial (Lightning Arrester), made of 25 mm dia 300mm long, GI tube, having single prong at top, with 85 mm dia 6 mm thick GI base plate including holes etc. complete as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing testing joint, made of 20 mm X 3 mm thick GI strip, 125 mm long, with 4 nos. of GI bolts, nuts, chuck nuts and spring washers etc. complete as required.

Safety Item (Electrical & Sub Station Area): Supply & erection of MS chequered plate of 600 X 400 X 7mm (thick) to cover the cable trench as required.

Supply, erection & fixing of ISI marked CO2 fire extinguisher suitable for 6.5 Kg.

Supply, testing & laying of 11kV Rubber Mat for electrical insulation purposes of size 6 ft X 3 ft X 0.5 at sub - station.

Supply & fixing of 6 No, GI fire bucket made from 24 SWG sheet of capacity 9 litre fitted on MS 50mm X 50mm X 6mm angle iron structure filled with clean & dry sand.

Supply & erection of shock treatment chart covered with glass & aluminium frame.

Supply & fixing of 11kV danger plate.

Supply and fixing of Schematic data on metal sheet of size 1200mmX600mm with aluminium frame

Supply & fixing of schematic diagram of HT/LT installation of suitable size.

Supply & erection of cable route marker for HT/LT cable made of CI plate duly engraved "Danger 11kV HT cable" & "440 V Cable".

Fire Detection System FIRE DETECTION AND ALARM SYSTEM - ANALOG ADDRESSABLE SYSTEM Design, Supply, installation, testing & commissioning of Fire Detection & Alarm system as per local fire norms & NBC / NFPA Codes:

Smoke Detectors (BFC) Supplying, installing, testing and commissioning approved make Addressable photo electric smoke detector. The acceptable sensitivity range of detector shall be in between 1.41 - 3.76 % / ft obs. The detector shall have single tricolour LED for 360 deg viewing. Addressing shall be via electronic means. The detector shall meet UL268, 7th guideline.

Smoke Detectors (AFC) Supplying, installing, testing and commissioning approved make Addressable photo electric smoke detector. The acceptable sensitivity range of detector shall be in between 1.41 - 3.76 % / ft obs. The detector shall have single tricolour LED for 360 deg viewing. Addressing shall be via electronic means. The detector shall meet UL268, 7th guideline.

Thermal Detectors (Rate of Rise) Supplying, installing, testing and commissioning approved make Addressable Heat detector. The Temperature range shall be between between 135°F (57°C) ─ 175°F (79°C) with fixed and rate-of-rise programmability. The detector shall have single tricolour LED for 360 deg viewing. Addressing shall be via electronic means. The detector shall meet UL268, 7th guideline.

Manual Call Point Supplying, installing, testing and commissioning approved make Addressable Manual Call Point (Single Action) The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. The device shall comply UL approval.

Fault isolator Supplying, installing, testing and commissioning of Isolator Module for Isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Monitor Module Supplying, installing, testing and commissioning approved make Addressable Monitor Module for Sprinklers, Panic Bars & other Third Party Inputs. The monitor module shall monitor potential free contacts. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the health status of the device. Addressing shall be via electronic means. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Fire Relay Modules Supplying, installing, testing and commissioning approved make Addressable Relay Module for AHU, Access Control, Lifts, Staircase Pressurization, Fire Suppression & other Third Party Outputs. The relay module shall provide contact rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be via electronic means. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Control Module Supplying, installing, testing and commissioning approved make Addressable Control Module for Sounders / Strobes / Sounder cum Strobes. The control module shall provide supervised NAC output rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be via electronic means. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Response Indicator Response indicator consisting of 16 gauge MS box with 75 x 75 x 6 thick cross brushed aluminium face plate for above false ceiling detectors.

Strobe Cum Hooter Supplying, installing, testing and commissioning of Sounder cum Strobe rated at 85 dBA @ 3m for Audible annunciation and 115cd flashintg at 1 Hz for visual indication. UL Listed

Fire Alarm Control System Fire Alarm Control panel Supplying, installation, testing and commissioning of 1-Loop micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting 252 detectors & Devices in any combination, with 6-inch (15.2 cm) touchscreen backlit multi-lingual liquid crystal display (LCD),minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger, Panel shall work in degrade mode in case of CPU failureThe panel shall be compatible for IBMS system. Should be designed to meet UL864 10th Edition

Cabling Job Supply, Installation, Testing and commissioning of 600/1000V rated, stranded copper conductor Fire survival 2C x 1.5 Sq.mm armoured cable in compliance to BS 7846 for the requirement of construction & performance and as per detailed specification provided. Cable shall be supplied with fixing accessories including end terminations, saddles, clamps with screws, cable tie etc. for fixing on wall/ceiling or on cable trays complete as required.

Area and Building Surveillance System Cameras 2MP IP Varifocal Vandal Dome Camera, Image Sensor: 1/2.7” 5MP Progressive scan Motorized Lens: 2.8 ~ 12mm, Resolution: 2880（H）x1620（V) or Higher IR Distance: 30 Mtr. Angle of View: Horizontal: 107-34°, Vertical: 55-19°, Diagonal: 134-38°, Min illumination 0.004lux,Video Compression: H.265+; H.265; H.264+; H.264; H.264B; MJPEG ,Video Streaming: Mainstream @30fps,5MP (2880x1620), 4MP(2592x1520) 3MP(2304x1296),1080P(1920x1080) 720P(1280x720), Substeam @30fps 720P(1280x720), VGA(640x480), QVGA(320x240), Third stream @30fps VGA(640x480), QVGA320x240); Motion Detection: 4 zone, Rectangle ; Major Protocols should include most of the following TCP/IP,HTTP,DHCP, DNS,DDNS,RTP/RTSP, SMTP,NTP,UPnP, SNMP, HTTPS,FTP, ONVIF (Profile S/Profile G/Profile T)must be listed on onvif portal; CGI; Event Trigger: Motion detection, Video tampering, Scene changing, Network disconnection, IP address conflict, Smart Detection:Face Recognition,Human&Vehicle Detection,Perimeter Intrusion Detection,Line Crossing Detection, Cross Counting,Stationary Object Detection, Heat Map,Crowd Density Detection,Queue Length Detection, Rare Sound Detection,Advance features: Starlight, WDR(120dB),Micro SD Card Slot up to 256GB, Alarm I/O-1/1, Audio I/O 1/1,Privacy Mask up to 8 level, ICR auto switch Power Source: 12V DC/PoE, Casing: Metal ,Weatherproof Standard: IP67,IK10, product must comply with NDAA complaince, Certification: BIS,CE,FCC,ROHS

2MP IP Outdoor Varifocal Bullet Camera, Image Sensor: 1/2.7” 5MP Progressive scan Motorized Lens: 2.8 ~ 12mm, Resolution: 2880（H）x1620（V) or Higher IR Distance: 50 Mtr. Angle of View: Horizontal: 107-34°, Vertical: 55-19°, Diagonal: 134-38°, Min illumination 0.004lux,Video Compression: H.265+; H.265; H.264+; H.264; H.264B; MJPEG ,Video Streaming: Mainstream @30fps,5MP(2880x1620),4MP(2592x1520) 3MP(2304x1296),1080P(1920x1080) 720P(1280x720), Substeam @30fps 720P(1280x720),VGA(640x480),QVGA(320x240), Third stream @30fps VGA(640x480), QVGA（320x240); Motion Detection: 4 zone, Rectangle ; Major Protocols should include most of the following TCP/IP,HTTP,DHCP,DNS,DDNS,RTP/RTSP, SMTP,NTP,UPnP,SNMP,HTTPS,FTP, ONVIF (Profile S/Profile G/Profile T) must be listed on onvif portal; CGI; Event Trigger: Motion detection, Video tampering, Scene changing, Network disconnection, IP address conflict, Smart Detection:Face Recognition,Human&Vehicle Detection,Perimeter Intrusion Detection,Line Crossing Detection, Cross Counting,Stationary Object Detection,Heat Map,Crowd Density Detection,Queue Length Detection, Rare Sound Detection,Advance features: Starlight, WDR(120dB),Micro SD Card Slot up to 256GB, Alarm I/O-1/1, Audio I/O 1/1,Privacy Mask up to 8 level, ICR auto switch Power Source: 12V DC/PoE, Casing: Metal ,Weatherproof Standard: IP67, product must comply with NDAA complaince, Certification: BIS,CE,FCC,ROHS

2MP 7-inch IR Outdoor PTZ Camera-1/2.8" Progressive Scan CMOS,Main Stream:25fps(2592x1944/2592x1520/2048x1536/2304x1296/1920x1080/1280x960/1280x720), Sub stream:25 fps (1280x720/640x480/320x240) ,Third stream: 25 fps (640x480/320x240),Focal Length: 5.0mm to 125mm, 25× Optical, 16x digital zoom, Color: 0.002 Lux @ (F1.6, AGC ON), ICR, Onvif ( Profile S, Profile G, Profile T) must available on onvif portal, support H.265+,MJPEG, 120 DB TWDR, 3D Digital Noise Reduction, HLC, BLC, Defog, EIS, DC 12V/POE+, IR range: 150m, Pan speed: configurable from 0.6° to 200°/s; preset speed: 200°/s,Tilt speed: configurable from 0.6° to 90°/s, preset speed 100°/s, Alarm Input-1-ch alarm input, Alarm Output-1-ch alarm output, Audio-1 channel input & output, Support on-board storage up to 256 GB (SD card not included), Supports intelligent analySupports intelligent analytics such as Auto Tracking,Face Recognition,Human&Vehicle Detection,Perimeter Intrusion Detection,Line Crossing Detection, Cross Counting,Stationary Object Detection,Heat Map,Crowd Density Detection,Queue Length Detection, Rare Sound Detection, product must comply with NDAA complaince, Certification: BIS,CE,FCC,ROHS

Network Video Recorder 32-Channel Network Video Recorder Max Resolution12MP; Bandwidth: Income 320Mbps; Outgoing 320Mbps; H.265+/H.265/H.264 Video Formats, 2 HDMI Port,US­ B3.0*1, USB2.0*2Support, 2xRJ45 Self-adaptivel0/100/1000 Mbps Network Interfaces, Sup­ ports live view, storage and playback of the connected camera at up to 12MP resolution, Connectable to the Third Party Network Cameras, Raid Supported: RAID0, RAIDl, Support Al: Face Detection & recognition, Vehicle & Pedestrian Detection, Cross Counting, Heat Map, Crowd Density Detection, Perimeter Intrusion Detection, Line Crossing Detection, Object Detection, Video Tempering, Queue Length Detection, License Plate Detection, Rare Sound Detection, Region Entrance & Existing, Web Monitoring: IEl0/11, Safari Vl2.l above, Firefox V.52 above, Google chrome V.57 above, Edge V.79 above, CE,FCC,ROHS,BIS,ISO 9001 Certified. Should support Harddisk capacity for recording of 8 cameras at FHD resolution @25FPS

LCD Display for CCTV Monitoring Supply, Installation, Testing & Commissioning of 32" LCD display with all accessory hardware & Software

Wiring & Port Supply, Installation, Testing & Commissioning of 24-Port Layer-2 switch and hardware accessories

Supply & Laying of CAT6 cable with PVC Conduit

Supply & Laying of CAT6 cable with GI Conduit for PTZ camera

Supplying, installing, testing and commissioning approved make FRLS PVC conduits on ceiling / wall / floor etc. complete with accessories like, Junction boxes, Collars, Bends etc.

Boom Barrier: Design,Supply ,installation,testing and commissoing of Electromechanical Boom barrier Manual Operation of length Upto 6 meter max. barrrier with push button only. Opening closing time 5-6 seconds. MTBF 5 Million Cycles. IP-54. Inclusive civil foundation 600mm X 600 mm X 100 mm. Make Godrej/Speedgate/Motwane with outdoor application,height of boom from 875 mm ,housing thickenss 2.0mm,Microprocessor based control unit,boom dimensinon 90x32 mm, IP54 controller protecting rating ,230 V,50/60 HZ ,24 V motor power supply ,200 W Power and Opening/Closing Time - 2 to 6 Secs , 100% Duty cycle,- 20 degree C to +55 degree C operating temperature necessary foundation/ fixing arrangements ,optical beam sensor ,access control operation, high range receiver,high range remote control,push button , bar with protective rubber profile ,flash point , manual release key in case of power failure ,for better visibity shall be aluminium with red reflective strip and all connected accessories ,including necessary foundation as per OEM instructions complete all as specified and as directed.

Supply & fixing of Photocell sensor for barrier

Supply & fixing of single channel loop detector

Exhaust Piping System Supplying and fixing exhaust gas piping of suitable dia. Welded black MS, B class pipe conforming to IS:3589 cut to required lengths and installed with necessary bends, supports and clamps, insulation of exhaust system with mineral wool / Rockwool, 50 mm thick wire mesh & aluminium cladding etc. as required as per specifications: 250 mm dia min. 4.5 mm thick

Supporting Structure Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (for cable support, for support of fuel tank, exhaust pipe including welding, grouting and painting with civil foundation etc. as required.)

Supplying, installation, testing and commissioning of 6 kg DCP extinguisher

Supplying, installation, testing and commissioning of Carbon dioxide type fire extinguishers of capacity 4.5 Kgs fitted with valve, discharge horn, conforming to IS 15683:2018

Supplying, installation, testing and commissioning of 9 ltr. Foam Extingusher with Trolly

Supplying, installation, testing and commissioning of Auto Glow Floor Indication & Exit Signages (450 x 200)

Water Supply Pumping Arrangment: Supply of 11KW/ 15HP Single stage mono block 65mm Section pipe capacity, 65/50 mm delivery pipe capacity based water supply pump of 2900 rpm speed, 240V 1-phase type.

Supply, Installation, testing and lifting/lowering from borewell of three phase Vertical Water Cooled Submersible Pump set to give discharge range upto 81 m3/hr at an head of 80 Mtr 415V, TP suitable for 200/250 mm dia bore well (suitable for casing pipe size 200/250mm) complete all as specified and directed.

Pump Control Panel with Star Delta Starter

Providing and fixing of GI Pipes complete with GI Fittings including, Cutting, Trenching, Fixing and laying (a) 80 mm Dia

Providing and fixing of GI Pipes complete with GI Fittings including, Cutting, Trenching, Fixing and laying (b) 65 mm Dia

Providing and fixing of GI Pipes complete with GI Fittings including, Cutting, Trenching, Fixing and laying (c) 50 mm Dia

Gun-Metal Non-Return Valve (NRV) of Different Size - Horizontal (a) 80 mm Dia

Gun-Metal Non-Return Valve (NRV) of Different Size - Horizontal (b) 65 mm Dia

Gun-Metal Non-Return Valve (NRV) of Different Size - Horizontal (c) 50 mm Dia

Water Flow Meter (a) 80 mm size Pipe

Water Flow Meter (a) 65 mm size Pipe

Air Conditioner Supplying, installation, testing & commissioning of 1.5 ton high wall inverter 5 star type split Airconditioner with copper coil material, tubing with nitrile rubber including indoor / outdoor units, suitable copper piping, stand for outdoor unit & all electrical connection etc complete.

Supplying, installation, testing & commissioning of 02 ton high wall inverter 5 star type split Airconditioner with copper coil material, tubing with nitrile rubber including indoor / outdoor units, suitable copper piping, stand for outdoor unit & all electrical connection etc complete.

Supplying, installation, testing & commissioning of stablizers of following capacity (a) 4 KVA

Supplying, installation, testing & commissioning of stablizers of following capacity (b) 5 KVA

Supply, Installation, Testing and Commissioning of Copper Pipe of following size soft copper piping with insulation of 6mm thick Nitrile Rubber pre formed sections including supporting fixtures and accessories etc., all complete (a) 3/4" Dia

Supply, Installation, Testing and Commissioning of Copper Pipe of following size soft copper piping with insulation of 6mm thick Nitrile Rubber pre formed sections including supporting fixtures and accessories etc., all complete (b) 1/4" Dia

Supply, laying, testing and commissioning of unarmoured copper power cable of size 3 Core x 1.5 Sqm

GYM EQUIPMENTS Providing & Fixing Resistance Bands Set for Exercise, Stretching, and Workout Toning Tube Kit with Foam Handles, Door Anchor, Ankle Strap, and Carrying Bag for Men, Women

Providing & Fixing (2.5 HP Peak) Manual Incline Motorized Treadmill for Home with 12 preset Workouts, Max Speed 12km/hr. Bluetooth Speaker|Max. User Weight 100Kg

Providing & Fixing 6 in 1 Multifunctional Weight Training kit - Dumbells, Kettlebells, Barbells & Push up Brackets in 1 (12)

Providing & Fixing Premium Workout Battle Rope for Core Strength Training, Poly Dacron Heavy Exercise Training Rope for Improve Strength Building Muscle - 30 Feet

Providing & Fixing Rowing Machine Indoor Rower Exercise Machine with 12 Gear Adjustable Resistance | Digital Monitor for Home Gyms Fitness and Cardio Training

Providing & Fixing Elliptical Cross Trainer With Lcd Display, Adjustable Seat, Hand Pulse Sensor, Adjustable Resistance For Home Use (Diy Installation With Video Call Assistance)

Providing & Fixing Heavy Duty Multipurpose Home Gym Bench, Adjustable Bench, Exercise Bench, Workout bench for the gym, Weight benches, bench for a home workout, an idol for bench press, Weightlifting bench

Providing & Fixing Power Squat Rack Heavy-Duty Adjustable Frame, Power Cages for Pull Ups and Training Purpose, Strength Training Equipments, Squat Stand for Home Gym Purpose

Providing & Fixing Fitness LAT Pull Down Machine with Cable Cross Over Machine Panel GF-72

Providing & Fixing 3 in 1 Heavy Duty Multifunctional Pull up bar for Wall mounting, Pull-up bar Training bar, dip Station for Training at Home, Training Weight up to 200kg

Providing & Fixing Premium All In One Suspension Trainer Kit for Full Body Workout Weight Resistance System | Suspension Straps for Training & Build Muscle Burn Fat Improve Mobility

Providing & Fixing Weighted Training Pull Sled with Vest - Fit for 1-2 Inch Plates, Sport Power Sled for Athletic Exercise and Speed Improvement

Providing & Fixing Gym Ball for Exercise - Anti Burst Exercise Ball with Foot Pump- Fitness Yoga Ball, Physiotherapy Ball, Birthing, Pregnancy & Labor Ball, Swiss Ball, Pilates Ball, Balance & Stability Ball

Providing & Fixing Fitkit by cult.sport FK4000 (Max Weight 120kg, Flywheel 13.22lbs) Bluetooth Enabled Exercise Spin Bike with Free Customized Diet Plan, Trainer Led Sessions & 6 months Warranty

Providing & Fixing FITNESS Alloy Steel Adjustable Dumbbell Set For Home Gym Fitness Equipment 10kg to 100kg (40KG) - Silver

Please Enable Macros to View BoQ information