Special repairs to OR Md Accn block No P-79 and P-87 at Mil Stn Suranussi under AGE (I) Suranussi

Amount

Demolition of brick work built in cement mortar including all quoins arches etc.

Demolition of cement conc in ground floor and pavings not exceeding 15 cm thick above or below ground level.

Taking down cement or cement lime plaster incl raking out joints hacking for keys srubbing down with water etc.

Taking down chowkats or frames with Shutters ( without taking off the shutter from the frame ) of area n.exc 1.50 Sqm each and removing from site.

All as per Item No 4 above but area exc 1.50 Sqm but n.exc 4.00 Sqm.

Taking shutter only of any desription of size n. exc 1 sqm.

Taking shutter only of any desription of size exc 1 sqm and n.exc 2sqm.

Ditto all as per item No 7 above but refixing in the same opening.

M&L brick work , with sub class 'B' bricks built in cement mortar 1:6 straight or curved on plan exc 6mtr mean radius.

Ditto all as per item No 9 above but Except bricks works.

M&L 15mm thick cement plastering in cement mortar (1:6) on other than fair faces of brick work or concrete surfaces finished even & smooth without using extra cement complete all as specified.

M&L for 15 mm thick cement plastering in cement mortar (1:4) on fair faces of brick work or concrete surfaces with using water proofing compound finished even & smooth without using extra cement complete all as specified.

M&l for 5 mm thick rendering in cement mortar in 1:3 on ceiling complete all as specified.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering to Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to GdeFe 290(Gde E-165) complete all as specified.

M&L for 35 mm thick IInd class HW , factory made Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified.

M&L for 35mm th IInd class HW glazed /gauged shutters open rebated and prepared to receive glass /gauge etc without sashbars edges of framing plain or chamfered r rounded fitted with cut and mitred beads for securing glass/gauge etc all as specified in SSR Part I section 8 clause 8.24 (a)complete all as specified.

S&F solid PVC door frame of sie 50mmX 47mm made out of 5mm th plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing complete all as specified.

S&F 30mm th factory made PVC door shutter solid panel consisting of frame made out of MS tubes for top & bottom rails .Ms frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC strip of 20mm width stuck inside with solvent cement for stiles and plain colourPVC sheet for top rail , lock rail &bottom rail on either side & as gap insert for top rail & bottom rail . Panelling of plain of plain colur PVC sheet to be fitted in the MS frame welded/sealed to stiles & rails with suitable PVC sheet beading and joined together with solvent cement ,etc all as specified and shown on drawings complete all as specified.

Supply & Fixing for steel windows 1.25 mm thick box type (primer coated) ERW hollow 'P' section of size 60mm x 25mm single rebate comprises of skeleton shutter ERW sec 50 x 20 mm & 1mm thick and openable leaf consisting two nos sash bar of T section 20x3mm complete welded to frame including cutting holes and making good dismanteled portion in cement concrete (1:2:4) type B-I four nos for each window including following fitting welded to shutter complete all as specified and as directed by Engineer-in-Charge :- (i) Hold fast 150mm long 12 mm x 3mm made to shape - 04 Nos each window. (ii) Handle of Z Section 20 x 25 mm, 100mm long 01 Nos each leaf. (iii) MS tower bolt 150 mm long-02 Nos each leaf. (iv) Z Section 20 x 25mm, 100 mm stopper - 01 Nos per leaf (v) Cleat 55 mm long of hollow square 15x20x63mm welded to hinges - 01 Nos per leaf. (vi) MS Box type hinges of size 75 X 12 mm - 02 Nos per leaf. (vii) MS Guard bars square 12mm dia @10 cm c/c with GI frame fixed to window frame. (viii) Fabrication and fixing.

Ditto all as above ser item No 19 here in before but skeleton shutter to recieving wire mesh as directed by Engineer-in-Charge. Notes for srl item no 19 & 20 :- 1. Glass/Wiremesh shall be measearued and paid seperately under respective items of BOQ. 2. Flat iron of size 25mmx4mm will be provided to assemble both type of shutters. No extra payment sahll be admissible for flat iron. 3. CEJZ/TD-1019/08 Sheet 1/3 to 3/3 & CEJZ/TD-1020/08 Sheet 1/3 to 3/3 whichever is applicable shall be followed.

S&F 300mm size mild steel sliding door bolt plate type stove enamelled black with bright bolt not less than 12mm dia incl a minimum of six nut and bolts ,four on bolt plate and two on stapple plate complete all as specified.

S&F mild steel barrel tower bolt 200mm size stove enamelled black with bright bolt etc all as specified.

S&F 150 mm size mild steel pressed handle oval type stove enamelled black complete all as specified.

S&F 100 mm size mild steel butt hinges medium weight complete all as specified.

S&F floor door stopper aluminiumalloy body and tounge 140mm anodised with hard drawn steel spring etc complete all as specified.

S&F 300mm size mild steel rat rail rod pattern spring including roller and roller plate complete all as specified.

S&F in repair block board 19mm thick commercial type exterior grade fixed to timber frame work complete all as specified.

S&F in repair pre laminated decorative block board 25mm thick prelminated on one face etc fixed to timber frame work complete all as specified.

S&F galvanized mild steel wire cloth 0.56mm dia of wire and average width of aperture 1.18mm complete all as specified..

Ditto all as per item No 29 above but fixed in repair complete all as specified.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame includingpunching or drilling out old glazing pins/spring clips and providing and fixing new ones, S & F 3 mm thick glass sheet ordinary quality glazing with oil putty in square n.exc 0 .5sqm in each pane complete all as specified.

S & F 3 mm thick glass sheet ordinary quality glazing with oil putty in square n.exc 0 .5sqm in each pane complete all as specified..

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified..

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over15 mm thick screed or bedding layer in CM 1:6 complete all as specified..

M&L Non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles over 15 mm thick screed or bedding layer in CM 1:6.complete all as specified and directed by Engineer-in Charge.

M&L for glazed ceramic tiles coloured of size 450 mm x 350 mm x 7mm th on vertical surfaces such as in skirting, dado etc over 10 mm thick backing coat in cm 1:4 complete all as specified.

M&L 18-19 mm thick machine cut kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, over 20 mm th screed or bedding layer in CM 1:6 complete all as specified.

All as per item No 37 above but as in skirting over 10mm thick rendering in CM 1:4 complete all as specified.

S&F in repair vitreous china squatting pan ‘Orissa patten’ size 580x440mm white with intergral foot rest (excluding flushing cistern and flush pipe) with "P' or "S" trap including water connection to trap and flushing pipe, flushing cistern etc incl lime concrete bedding and PCC 1:2:4 for making good the floor fixed in repair complete all as specified and directed.

S & F in repair PVC 10 ltrs syphonic action type flushing cistern, low level with inlet, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets ball valve, float and handle including brackets,and connections to pipes and fixing of chain and pull, or lever, if anycomplete all as specified.

S& F in repair vitrious china wash hand basin flat back 550X400mm incl fixing bracket, pvc waste coupling and waste pipe,cp pillar tap etc all as specified and directed by engineer-in-charge.

S&F in replacement 20 mm dia harrison rails mild steel with decorative finish , with fixing brackets , stops, rollers complete all as specified and as directed (two brackets per 1.5 M length and 08 Nos roller per 1.RM).

Dismantling brick tile or terracing tile single layer on roof.

Demolition of mud in roofs ,any thickness incl plastering and leeping (weather full thickness removed or part there of).

Demolition of cement Concrete of any description and in any position not otherwise specifically provided for.

M/L for PCC 1:5:10 type E2 with using 40 mm graded stone aggrgate as in filling for sunken floor and like works complete all as specified & as directed.

Supply only Integral waterproofing compound complete all as specified & as directed.

Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified & as directed.

APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms/sqm) laid on primed surface by torch application complete all as specified complete all as specified & as directed.

M&L for 40mm average consolidated thickness PCC 1:2:4 type B1 with using 20mm graded stone aggregate as in padding on flat roofs etc all as specified and directed.

M/L 40mm thick brick tiles laid on mud mortar and joints grouted flush incement mortar (1:3) mixed with 5% of crude oil by weight of cement and pointed flush in CM 1:3 complete all as specified.

All as per item No 52 above but except tiles complete all as specified..

Dismantling water tanks of any description exc 250 and n.exc 500 ltr capacity.

S&F Rotational moulded polythene water storage tanks double layer (cylinder each vertical with closed top) of capacity 500 Itrs, hoisted and fixed in position including pvc float valve 20mm size,specified in SSR Pt-1 complete all as specified.

Taking up/ down GI tubing and connections with all fittings 15 mm bore.

Ditto all as per item No 56 above but 20mm bore.

S&F 15 mmdia GI tubing and connections fixed to wall or ceiling, laid in floor etc complete all as specified.

S&F 20 mmdia GI tubing and connections fixed to wall or ceiling, laid in floor etccomplete all as specified.

S&F in repair CP shower rose 15mm sizefixed to iron pipe complete all as specified.

S&F pvc connection 15mm size with PTMT nuts of length 450mm complete all as specified.

S&F in repair 15mm CP Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S&F in repair 15mm size brass stop valves with crutch or butterfly handles high pressure screwed both ends for iron pipe complete all as specified.

S&F in repair 20mm size stop valves PTMT high pressure screwed for iron pipe complete all as specified & as directed.

Ditto all as per item No 64 above but fancy type, chromium plated with long shank and cup (concealed type) complete all as specified.

S&F in repair towel rail 600mm long of PTMT incl cp brass srews etc complete all as specified & as directed..

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

M&L for framed work such as grill grating etc with end of bars rivetted or shouldered and rivetted or forged in to spikes , framed guard bars etc all as specified ( Fe 290 Gde E-165).

M&L preparing new surfaces of walls and applying two coats of oil bound distemper over a coat of alkali primer etc all as specified.

M&L preparing old surfaces of walls and applying two coats of oil bound distemper etc all as specified.

M&L preparing surfaces of new walls and applying two caots of cement base paint over and a coat of alkali primer complete all as specified.

M&L for Complete removal of existing treatment of walls and applying two caots of cement base paint etc all as specified.

M&L for three coats of white wash on on ceiling on newly plastered surfaces complete all as specified & as directed.

M&L for two coats synthetic enamel paint on new wooden surface over 10 cm width or girth over a coat pink primer complete all as specified.

Ditto all as per item No 74 above but one coat on old treated surface complete all as specified.

M&L for two coats of synthetic enamel paint on new steel surface over 10cm width or girth over a coat red oxide primerv etc all as specified.

Ditto all as per item No 76 above but one coat on old treated surface etc all as specified.

M&L for Screed bed or bedding layer of mortar 20 mm thick in CM 1:4 for laying floor finishes complete all as specified.

M & L for chequered cement concrete tiles 20cm x 20cm x 25mm thick set, jointed and pointed in neat cement slurry and pigments as in floors complete all as specified and directed by Engineer-in-Charge.

M/L Providing, cement concrete type B0 1:2:4 (12.5 mm graded aggregate ), as in roof kerbs or mud stops, rounded or chamfered on edges parapets copings, bed plates, etc complete all as specified.

M&L PCC 25mm th 1:2:4 type B-0 using 12.5 mm graded stone agg as in levelling course complete all as specified.

M&L for 50 mm th PCC 1:3:6 type C2 as in plinth protection with using 40mm graded stone aggregate etc all as specified.

S&F in repair PVC SWR pipe 75 mm dia single socketed in any length with rubber ring joints fixed to walls etc all as specified.

Ditto all as per item No 83 above but laid in trenches complete all as specified.

S&F in repair PVC SWR pipe 110 mm dia single socketed in any length with rubber ring joints fixed to walls etc all as specified.

Ditto all as per item No 85 above but laid in trenches complete all as specified.

S&F in repair 75mm size PVC (SWR) floor trap plain with grating incl to jointing with waste pipe with adhessive etc all as specified.

S&F 110 mm dia PVC SWR type bends any radius complete all as specified.

Ditto all as per item No 88 above but 75mm dia etc all as specified.

S&f 100 mm dia stack clamp made out of 25x4mm Flat iron etc all as specified.

S&f 75mm dia stack clamp made out of 25x4mm Flat iron etc all as specified.

Cutting grooves of size 75mm wide and 65mm deep in brick parapet wall for inserting APP membrane and making good the disturbed portion in CM (1:3) etc all as specified.

M & L Cement concrete 1:2:4 type B–1 using 20mm graded stone aggregates as in, copings, finishing side to path, including weathering, slightly rounded or chamfered angles and throating, as directed all as specified and directed by Engineer-in-Charge.

Form work to soffits of suspended slab such as roof slab/Kitchen slab n exc 200mm thick (horizontal/sloping/vertical) with fair finished surface complete all as specified.

M & L TMT bars 6mm to 8mm dia. cut to length bent to shape required including cranking, bending and binding with and including ms wire (annealed) n. less than 0.9mm dia or securing with clips complete all as specified.

Demolition of cement concrete is reinforced of any description and in any position not otherwise specifically provided for.

M&L Reinforced cement concrete (nominal mix) Type B-0 1:2:4 (12.5mm graded aggregate) in slabs supported on walls, beams, columns deck slabs and in shelves, the like all as specified and directed by Engineer-in-Charge.

M & L Reinforced cement concrete (nominal mix) Type B-0 1:2:4 (12.5mm graded aggregate) in Chajjas all as specified and directed by Engineer - in - Charge.

Taking down carefully aluminum point wiring on TW Batten/in conduit / with conduit (light/Fan/socket or power) complete and making good the disturbed surfaces of wall/ceiling etc including taking down fittings such as switches, ceiling roses, pendants, Regulators, sockets, light fittings etc and removing material from site except tube light fittings, fans etc which shall be re-used in work complete all as directed.

Material and Labour for Concealed point wiring complete with 1.5 Sq.mm (nominal area) FR PVC insulated multi stranded copper conductor in and including heavy duty PVC conduit (wall thickness 1.6 mm) including fittings & accessories, with MS concealed terminal boxes with 3mm thick laminated bakelite ( Hylum/Anchor) sheet top cover for mounting switch, socket etc for one light/fan/bell point controlled by one switch and regulator with PVC cable copper conductor including 1.5 Sqmm solid copper conductor with green FR PVC insulation earth common earth dolly, complete all as specified.

All as per ser item No 100 above but for 3 pin socket out let 5 Amps on same board complete all as specified.

All as per ser item No 100 above but for 3 pin socket out let 5 Amps on independent board complete all as specified.

All as per srl item No 100 above but for 3 pin socket outlet 15 Amps with 2.5 Sqmm stranded copper conductor PVC unsheathed cable independent including PVC cable copper conductor 2.5 Sqmm with green insulator as earth wire with cast iron/pressed steel terminal box all as specified.

All as per item No 100 above but one light point controlled by two way switches complete all as specified.

Supply and fixing switch piano flush type 5 Amp single pole one way complete all as specified.

Supply and fixing switch piano flush type 15 Amp single pole one way complete all as specified.

Supply and fixing switch piano 5 Amp flush type single pole two way complete all as specified.

Supply and fixing socket outlet 5 pin 5 Amps flush type multi purpose complete all as specified.

Supply and fixing socket outlet multipurpose 2 in one, 6 pin 15Amps flush type complete all as specified.

Supply and fixing angular lamp holder insulated body with back plate suitable for pendent fittings.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & as directed

Supply and fixing LED lights fitting 1x 10W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified.

Supply and fixing ceiling rose surface bakelite 65 x 50mm three terminals complete complete all as specified.

Supply and fixing bell push flush type 5 Amps complete all as specified & as directed .

Supply and Fixing fan regulator electronic step type and making connection complete all as specified.

Supply and fixing sheet steel enclosure with double door, detachable gland plates flush/surface mounting for MCB’s fitted with bus bar, earth bar and neutral link 8 ways SPN 240 V complete all as specified.

Supply and fixing sheet steel metal enclosure (DB) triple pole and neutral 4 way 415 ,Volt with 200 amps rated bus bar complete all as specified.

Supply and fixing Isolator SPN 240V, 40 Amp complete all as specified.

Supply and fixing Isolator SP 6 to 40 Amps 240 Volts complete all as specified.

Supply and fixing Isolater 63 Amps TPN 415 Volts complete all as specified.

Supply and fixing call bell single phase 240 volt complete all as specified & as directed.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified.

Supply and fix fans ceiling complete with electronic type regulator and accessories 230 V, 1200 -1400 mm sweep complete all as specified.

Supply and fixing exhaust fan 300 mm sweep 900 mm,heavy duty,AC single phase 230/240 volts,metal body with louver shutters including making circular hole in existing wall to accommodate exhaust fan and necessary civil work and making good the disturbed surface complete all as specified and directed.

M&L for submain wiring with two runs of single 4 sqmm PVC insulated unsheathed multistranded 1100 vols grade with copper conductor drawn through and including in steel conduit medium grade ISI marked and its accessories including one run of single core 4 sqmm PVC insulated unsheated multistranded 1100 volts grade with copper conductor cable as earth contuinity conductor along with the wiring and connected from DB to DB/ main board completeall as specified and as correct.

Material and Labour for earthing with galvanized iron earth plate electrode 600mm x 600mm, 6mm thick buried directly in ground vertically in a earth pit not less than 2.25mtr below normal ground level with top edge of the plate not less than 1.5mtr below normal ground level connected to GI earth wire 4mm dia by means of GI bolts, nuts, check nuts and washers (earth plate covered with alternate layers of charcoal dust and common salt 15cm thick), GI earth wire protected by GI pipe light grade 15 mm dia upto switch board and connected to main switch board including provision of GI pipe 20 mm dia light grade watering pipe with funnel and wire mesh, all as shown in Electrical Plate No. 3 of SSR Part-I, including PCC chamber (1:3:6) using 20mm graded stone aggregate and CI cover and frame including all necessary excavation and earth work and taking out old earthing complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 3½ Core complete all as specified & as directed.

Supply and fix GI tubing light grade for encasing cables for protection, laid under plinth/floors/roads/path/culverts or fixed on walls/on poles by means of MS clamps with necessary bolts, nuts and washers 40mm bore all as specified and directed.

Excavation over areas in soft/loose soil not exceeding 1.5 mtr deep and not exceeding 1.5 mtr wide for laying of cables, poles/stays and struts etc getting out including trimming sides and forming bottom surface all as specified and directed at site.

Returning, filling in including spreading, leaving,watering and well ramming excavation hard/soft in layers not exceeding 25 cm thick each, back in trenches after cables have been laid and tested, poles, stays, struts have been erected and tested, all as specified and directed.

Removing excavated surplus soil (Soft/loose soil) obtained from excavation to a distance not exceeding 50 mtr and deposting where directed at a level not exceeding 1.5m above the starting point all as specified and directed.

Material and labour for clean dry sand laid in trenches/ ducts for cushioning to cable complete all as specified.

Supply and fix common burnt clay building bricks sub class B designation 75 complete all as specified & as directed.

SUNRISE CONSTRUCTION COMPANY

DUGGAL CONSTRUCTION CO