REPAIR/ MAINTENANCE (B/R PART) OF WATER SUPPLY INSTALATION OF AGE E/M UNDER ZONE-I AREA OF GE JAIPUR

Amount

M & L for preparation of old surface of walls and applying one coat of cement paint of any tint all as directed.

All as per item No 1 above but two coats of cement base paint

M&L preparation of old steel surface and applying one coat of synthetic enamel paint all as specified

M&L for including sand paper gentle rubbing to obtain smooth surfaces and applying one coats of oil bound distempering white or tinted using hand roller /brush on wall Surface including all necessary arrangement for execution of work, complete all as specified and directed.

M&L for including sand paper gentle rubbing to obtain smooth surfaces and applying two coats of oil bound distempering white or tinted using hand roller/brush on Wall Surface including all necessary arrangement for execution of work ,complete all as specified and directed.

M & L for preparation of old decorated surfaces of walls, pillars and cornices including brooming down and cleaning the surface and applying two coat of white wash all as specified and directed

M & L for preparation of old plastered or unplastered decorated surfaces and applying two coat of white wash on ceiling all as specified and directed

M&L for one coats painting with synthetic enamel paint to old wood or wood based surfaces of any description, not otherwise described over 10 CM width or girth including preparation of surface including all preparatory work complete all as specified and as directed by Engineer-in-Charge.

Complete removal of existing treatment & M&L for thourughly wetted surface to ensure better sticking including sand paper gentle rubbing to obtain smooth surfaces, including all necessary arrangement for execution of work ,preparation of existing surface with putty that applying (priming seal -o- prime ) on platered surface and two coat of weather proof exterior emulsion paint (weather coat smooth) using hand roller on external wall Surface of OVER HEAD TANK upto 25 meter hieght from GL complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete in ground floors and pavings not exc 15cm thickness (below or above ground level) complete all as specified and directed

M&L broken stone or boulders for hardcore of gauge not exc 63mm, deposited , spread and levelled in layers not exc 15cm thick watered and rammed to a ture surface complete all as specified and directed

M & L plain Cement Concrete 1:4:8 type D-2 (40mm graded aggregate) in sub base of floors

M & L 75 mm thick plain Cement Concrete 1:2:4 type B-2 (40mm graded aggregate) in sub base of floors complete all as specified and directed

M & L 40mm thick plain Cement Concrete 1:2:4 type B1 (20mm graded aggregate) in sub base of floors complete all as specified and directed

Demolition stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in cement mortar

M & L Machine pressed precast rubber moulded concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, with grey cement laid over and including 25mm thick sand cushion layer complete all as specified and directed

All as per item No 16 above but except tiles

M&L rubber moulded chequered cement concrete tiles 20cm x 20cm x 20mm thick , set , jointed and pointed in neat cement slurry in floors with grey cement and pigment over & including 20mm thick screed bed in CM 1:6 complete all as specified and directed

All as per item No 18 above but except tiles

M & L for precast PCC blocks or slabs 150 mm thick (1:2:4) mix type B-1 using 20 mm graded aggregated with plain or interlocking joints as directed complete in walls setting in CM (1:6) complete all as specified and directed

M&L for 50 mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement including necessary complete all as specified and directed by Engineer-in-Charge.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles.

M&L for brick work with old size sub-class ‘B’ bricks, straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 for raising of height of drain, manhole / wall complete all as specified.

All as per item No 23 above but except brick

Taking down cement plaster or cement lime plaster on brick / stone surfaces of wall or ceiling including raking outs joints, hacking for key scrubbing down with water etc

M&L for Chipping the RCC surface and cleaning the rusted reinforcement and exposed surface by wire brush, mechanical device or any other established method and applying the rust removing solution of approved make and quality with cotton swab to reinforcement and allowing to dry the same for 24 hrs ,brushing of loose particles and applying 1st coat of rust preventive coating of polymer and cement slurry in 1:1.5 proportion with soft brush without adding water including applying another coat of rust preventing after 4 hrs allowing air curing for 48 hrs etc. complete all as specified and directed (Note: Scaffolding/ staiging shall be includede in quoted rate)

M & L for 30mm thick polymer mortar to load carrying RCC members in two layers in proportion of 1:5:15 by weight of polymer of approved make and quality, cement and quartz sand with required WC ratio for desired consistency and applying and finishing by floating, curing after initial setting time etc. as per manufacturer specification etc. for OVER HEAD TANK upto 25 meter hieght from GL including all necessary arrangement complete all as specified and as directed by Engineer-in-Charge.

M & L for 15mm thick polymer mortar to load carrying RCC members in two layers in proportion of 1:5:15 by weight of polymer of approved make and quality, cement and quartz sand with required WC ratio for desired consistency and applying and finishing by floating, curing after initial setting time etc. as per manufacturer specification etcor OVER HEAD TANK upto 25 meter hieght from GL including all necessary arrangement complete all as specified and directed by Engineer-in-Charge.

M & L rendering 15mm thick on stone masonary surfaces or surface other than fair faces of brick work on wall in CM 1:4 finished even and smooth without using extra cement.

M & L rendering 15mm thick on fair faces of brick work or concrete surfacel in CM 1:4 finished even and smooth without using extra cement.

M & L for preparation of new plastered wall surfaces and applying two coats of cement base paint on wall

M&L for granite (of any type), 16mm to 18mm work (table rubbed and polished) in steps, jamps, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M&L for Dholpur stone 16 to 18 mm cladding gang saw cut with macnine cut edges, uniform colour of each stone size exceeding 0.25 sqm area and not exceeding 0.5 sqm fixed with and including one mumber SS clamps (grade-202) of flat 30mm X 2mm, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fasterner, polishing, rubbing & including silicon treatment.

M & L machine cut kota stone slab flooring 20-25mm thick,size of kota stone 450x450 mm over and including cement screed bed 20mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

Dismantling structural steel work including doors, gates, wrought iron or mild steel work of any description complete all as specified and directed.

S&F rolled mild steel work as in Joist, channel, angle or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lenghts i.e. within 20mm of the lenght directed) and similar work conforming to Fe-290 GdeE-165.

S&F mild steel work such as angle iron in posts & struts in fencing including cutting tops to shape hand rail straight portion , drilled and contersunk for balusters , nosing to steps, struts in fencing including cutting tops to shape as directed , drilling holes, notching for wire etc flat iron fillets ( for securing chain link fencing ) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 Gde E-165

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also fastening and fixing complete

S&F in repair mild steel round bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for chain link fening ( in new or old )

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil.

Dismantling galvanised chain link fencing of any description fixed to any type of fencing posts

Supply only chain link fencing 4 mm dia galvanized steel 100mm x 100mm mesh fixed to angle iron fencing post or angle frame complete all as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire

S&F screw bolts (machine made) with hexagonal or square head at one head and rounded the other or screwed both end each screwed end to be fitted with washers and one hexagonal or square nut exc 10cm nexc 15cm long dia of shank 11 to 15mm complete all as specified and directed

S&F as in repair galvanized 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossing with and provision of galvanized mild steel wire, staples or steel pins etc complete all as specified and directed

M&Lfor preparation of new steel surface of any description n. exc 10cm in width or girth when un connecting to other painting surface and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coarch screw and washer in roof wall etc

M&L for pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified

Dismantling plain or corrugated steel / FRP sheeting any gauge, thickness including nainital or similar pattern roof /wall covering

S & F steel work in tubular/ square/ rectangular trusses incl special shaped washer etc, complete using ERW orinduction butt welded tubes conforiming toIS 1161-1979 graded St-240

M&L for prearation of new steel surface and applying two coat of synthetic enamel paint over a coat of red oxide primer all as specified

M&L plain cement concrete type B1 1:2:4 ( 20mm graded aggregate) as in lintels, cills steps, seismic and other similar bands , copings, kneelers, apex stone bed plates , kerb ,water troughs and like including weathering, slightly rounded or chamfered angles and throating as directed.

S&F Sign board made out of 03mm aluminum composite panel both side alongwith retro reflective sheeting on both side with letters, stops, commas, short lines, dashes, hyphen, brackets etc of 100-150mm size fixed on 75mm dia SS Pipe of 3 mtr long all as specified and directed. Note: Area of sign board only shall be considered for payment

M&L for 25mm thick plain cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in floor all as specified

M & L for coloured non skid ceramic tiles 300x300x7mm thick in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over & including 15mm thick screed bed in CM 1:6 complete.

M & L for coloured glazed non skid joint free tiles 400x400x7 to 8mm thick in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over & including 15mm thick screed bed in CM 1:6 complete all as approved and directed

M & L for coloured glazed joint free ceramic tiles 450x300x7 to 8mm thick in vertical surface as in skirting over & including 10mm thick rendering on stone masonry surfaces or surfaces other than fair faces of brick work in CM 1:4 complete all as approved and directed

S & F in repair galvanised mild steel wire cloth 0.63 mm nominal dia of wire & average width of aperture 1.40mm and fixed with stainless steel wire staples

Taking down of shutters of any description exc 1 sqm but n exc 2 sqm each

Taking down door chowkaht or frame of any description area n.exc 1.50 Sqm each without taking off shutters from the frame.

Taking down door chowkaht or frame of any description area exc 1.50 Sqm but n exc 4 sqm each without taking off shutters from the frame.

Taking down resecuring or easying and refixing in same opening of old door shutters of any description exc 1 Sqm but n exc 2 Sqm in size.

S & F 35mm thick factory made plain, framed, paneled door shutters kiln seasoned and chemically pressure treated second class, hardwood (two panels) with lock rail and panel of 9mm thick BWP commercial marine grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive confirming to IS-710. The size of rails and style shall be as per IS-1003.

S & F 35mm thick factory made second class hardwood glazed and skelton door shutter kiln seasoned and chemically treated, open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete. The size of members of shutters shall be as specified in MES SSR Part-I.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube of 1.25 mm thickness suppling & fixing in opening as per specification & drawing.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S & F 300mm long mild steel sliding door bolt clip type stove enamelled black with bright bolt not less than 12mm dia with & including a min of six bolt & nut, four on bolt plate & two on staple plate

S & F 150mm long mild steel pressed handles oval type stove enamelled black complete

S & F 125mm long aluminium handles, cast type anodised complete

S & F 150mm long mild steel barrel tower bolt stove enamelled black with bright bolt and fixed complete

S & F 125mm long aluminium anodised barrel tower bolts of extruded section and fixed complete

S & F 100mm butt hinges medium weight cold rolled mild steel and fixed complete

Supply only 3mm thick plain sheet glass ordinary quality and glazing with oil putty in sqaures not exc 0.5 sqm in each pane.

Dismantling old unserviceable RCC / PVC water tank & removal from site complete all as directed capacity exceedind 250 ltr and not exc 500 ltrs

S & F 500 Ltrs capacity rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe pipe etc complete all as specified and directed.

S & F in repair towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms).

S&F in repair CP brass shower rose with swivel joints, including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of CP brass complete all as specified.

S&F in repair Vitreous china squatting pan Orisa pattern, size 580X440 mm white with intergral foot rest, with pvc valve syphonic action type flushing cistern, low level white ,with inlet, ball valve, float and handle including brackets 10 ltr capacity flush pipe of pvc 32mm dia for low level cictern complete.

S&F in repair vitreous china wash basin , white flat back size 550X400 mm including brackets , 32 mm dia waste coupling of PTMT (min weight 450 gms) 25mm dia PVC waste pipe 75 cms long with necessary fixing arrangement ,fancy type pillar tap cast copper alloy with capstan head cromium heads, chromium plated, screwed down high pressure with long screwed shanks and fly nuts complete.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm.

S&F in repair grating doom 100mm dia of PTMT (min weight 25 gms)

S&F in repair waste coupling of PTMT (half or full threaded) complete

S&F shelf of PTMT fixed to wall with steel screws and PVC rawl plug complete all as specified.

S&F sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12CM wide with chromium plated bracket guard and railing 60 CM long complete all as specified.

S&F 15mm bore fancy type stop valve / angle valve of cast copper alloy chromium plated screwed down, high pressure with crutch or butter fly handles screwed both ends for iron pipe or for unions complete all as specified.

S&F in repair bib taps 15mm bore short body cast coper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union complete all as specified and directed. (Cat Part No : F330003) Make : Hindware

Taking up or down 15mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed

Taking up or down 20 mm steel tubing and connections including cleaning for refixing or removal complete all as specified and directed by Engr-in-Charge

S&F15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

S&F 20 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge

Schedule of Credit

S.R.Enterprises

SAI MAX INFRAPROJECTS