NIT No-05 / EE (EnM) WnS S-III item No-02

LT Distribution panel sheet steel enclosure made out of 2 mm CRCA sheet totally enclosed, powder coated free standing, floor mounted type, dust & vermin proof, outward opening, lockable doors having hidden hinges and a bolted back cover both using non-deteriorating neoprene rubber gaskets to provide IP-54 protection .The each part of the fabricated panel will be strictly subjected to seven tank treatment. The various components, assemblies and sub equipment of the panel will be as per standard given in relevant IS. The bus bar of the panel will be shaped out of high conductivity, electrolytic conductor and shall be liberal sized in aluminium. The control wiring of the panel will be done with PVC flexible copper wires of 1.5 mm cross section. Each wire will be terminating with a ferule crimped to the wire, size 1800MM x1600x375mm. Having following components of approved make.

MCCB 415V, FP 3 phase High breaking capacity 50 KA 50Hz, 400Amp with spreader & Handle. Make :- L&T/Siemens

MCCB 415V, TP 3phase High breaking capacity 50KA 50Hz, 125 Amp with spreader & Handle. Make :- L&T/Siemens

MCB Single pole 6Amp. Make:- L&T/Havells

MCB Triple pole 63Amp. Make :- L&T/Havells

MCB Triple pole 32Amp. Make :- L&T/Havells

PVC insulated copper flexible cable single core 35 Sq mm Make:-Havells/Gloster/Finolex

Power capacitors 415V unit of 20 KVAR (Rs.247/-per KVAR) Make: Epcos

Over load relay 66-110 A Make: L&T/Siemens

Over load relay 6-10 A Make: L&T/Siemens

Digital Amp. Meter Make :- AE/L&T

Digital Volt Meter 0-500V Make :- AE/L&T

Motor protection Relay Make :- L&T/Siemens

Power contactor 220V 3 phase 95 Amp. Make :- L&T/Siemens

Power contactor 220V 3 phase 70Amp. Make :- L&T/Siemens

Power contactor 220V 3 phase 25Amp. Make :- L&T/Siemens

Star delta timer on delay make :- L&T/Siemens

Indicating lights LED type RYB & On/Off . Make :- L&T /Havells

Current Transformer 250/5 , 100/5 ,30/5 Make :- AE /Advance

On load change over switch 200 Amp. Open execution type Make :- L&T

Fitting of the above components in panel enclosure with terminal blocks, channels, ferrules, thimble, support insulator on bus bar, required hard wares complete in all respect.

Loading ,unloading by crane or heavy labour and cartage up to site cleaning & dressing the surface for Installation of the panel at site on base frame ,laying of cable ,termination of cable both incoming & outgoing side

Testing & commissioning of panel, as per required parameters with relevant IS .testing of the panel prior to switching on as follow (i) Continuity and earth testing (ii) Meggaring of all equipment for phase to phase, neutral to body, neutral to earth and phase to earth. (iii) Checking for all tightness of nut and bolts (iv) Alignments of doors etc. (vi) Interlocking tests. All function tests

Supply of Horizontal split casing pump with impeller and neck ring (Bronze), shaft and sleeve (SS- 410) and casing (CI) in fitted condition with suitable bearing along with IE2 rating TEFC motor. The pump and motor coupled on M.S Base plate with coupling and coupling Guard Head- 45 mtrs Discharge- 230 m3 / hr. Motor Ratings- 45KW/60 HP RPM- 1475 Duties of pump- Make M&P/ Kirloskar(Make of motor- CG/ABB/ Kirloskar/ DJB approved)

S/o Self priming Dewatering mono block pump model SP2HM,3 HP, 50x50 mm with CI impeller,EN-8 Shaft & gland packed 5 Hp 2800 RPM Make :-Kirloskar/M&P

S/o Vacuum Pump Model DV - 40 Size 40 mm x 40 mm coupled with motor 5HP, 1450 RPM 415 volt mounted on MS Fabricated Base frame coupled and Guard. Make:-Kirloskar/M&P

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. DSR 2018- 10.2

Providing and lying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering – All work up to plinth level: 1:2:4. ( 1 cement :2 coarse sand (zone –III) : 4 grade stone 20mm nominal size ) Volume of foundation 60 HP Electric pump set= 2 ( LxBxH) A- 2nos x(1.8x0.75x1.2 m= 3.24 cum B-Vacuum pump set = 1.00x0.6x1.2m= 0.72cum C-Dewatering mono Block =1.00x.6x1.2m=.72cum Total = 3.24+0.72+.72= 4.68 cum 5.1.3 DSR 2018

Centering and shuttering including strutting, propping etc. And removal of form for: For foundation, footing, bases of columns etc. for mass concrete. 5.9.1 DSR 2018

Steel reinforcement for RCC work for including straitening, cutting, bending, placing in position in binding all complete up to plinth level. Cold twisting bars 5.22.3 DSR 2018

Steel work in built up tubular ( round, square, rectangular hollow tubes etc.) trusses etc. including cutting, hoisting, fixing, in position and apply a primary code of approval steel primer, including welding and bolted with special shaped washer etc. Complete. Hot finished welded type tubes 10.16.1 DSR 2018

Providing of 200 mm dia. Non rising spindle CI D/F sluice valve as per IS 14846 PN 1.0. Make – Kirloskar / IVC.

Providing of 150 mm dia. Non rising spindle CI D/F sluice valve as per IS 14846 PN 1.0. Make – Kirloskar / IVC.

Providing of 150 mm dia Non return Valve CI D/F as per IS 14846 PN 1.0 Make – Kirloskar / IVC

Providing of 200 mm dia Foot Valve CI as per IS 14846 PN 1.0 Make – Kirloskar / IVC

Providing of Rubber insulation sheet, size 1.5 mm thickness. Make :- Jyoti/National

Providing of MS foundation Bolts of sizes 20 mm x 450 mm ISI mark

M S nut bolts size 16mm x 75mm ISI mark

Providing and fixing GI pipes ( medium) with fittings for external work including trenching and refilling Etc. External work 32 mm dia nominal bore 18.12.4 DSR 2018

Providing and fixing GI union in GI pipe including cutting and threading the pipe and making long screw etc complete (New work) 32 mm nominal bore 18.46.4 DSR 2018

Providing and fixing Gun metal valve with C.I wheel of approved quality (Screwed end) 32 mm nominal Bore 18.17.2 DSR 2018

Providing and fixing GI pipes ( medium) with fittings for external work including trenching and refilling Etc. External work 50 mm dia nominal bore 18.12.6 DSR 2018

Providing and fixing Gun metal non return valve of approved quality (Screwed end) 50 mm nominal Bore Vertical 18.19.4.2 DSR 2018

Providing and fixing GI union in GI pipe including cutting and threading the pipe and making long screw etc complete (New work) 50 mm nominal bore 18.46.6 DSR 2018

Fixing of M S base frame on the RCC foundation and tightening with foundation Nut Bolts. Fixing of Electric pump set on the MS base frame, make proper alignment and tightening the same with the help of required arrangements.

Making suction connection by fixing of sluice valve, gap pieces and flange as per site requirement. & Making delivery connection by fixing of sluice valve, NRV, gap piece and flanges as per site requirement

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture DSR 2018.13.62.1

Loading, unloading by crane or heavy labour and cartage up to site i/c Motor p/set, vacuum P/set, dewatering p/set etc. It also i/c the all job work which required to commissioning the BPS at per site requirement.

Testing and commissioning of complete system at no load and full load with all the required tests.

Shakti Trading Co.