SPECIAL REPAIR OF OR GOVT MD ACCN NO P3 P7 P8 APS COMPLEX PROVN OF ONE OVERED TRG SHED WITH HARDSTANDING AT MARIANI AND PROVN OF IRON GRILL ON EXISTING WINDOWS IN BLDGS IN ALL POCKETS OF MARIANI SARAIBARI AND BHALUKMARA AT JORHAT

Amount

Dismantling boarding, any description, fixed in any position with nails etc complete all as specified and as directed.

S&F Pre-painted, galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws,complete all as specified and directed.

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) etc complete all as soecified and as directed.

Materials and Labour for 75 mm thick plain cement concrete (1:3:6) type C1 using 20 mm graded aggregates as in plinth protection including finishing surface even and smooth without using extra cement , complete all as specified and as directed.

Materials and Labour for filling of joints with bitumen 85 / 25 grade mixed with coarse sand (1:3) etc complete all as specified and as directed.

Materials and Labour for plain cement concrete (1:3:6) type C1 using 20 mm graded aggregate as in surface channels and drains including necessary formwork etc complete all as specified and as directed.

Dismantling wrought iron or mild steel of any description not otherwise provided for etc complete all as specified and as directed.

Dismantling timber fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section etc complete all as specified and as directed.

Supply only integral water proofing compound ISI marked etc complete all as specified and as diretced.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as directed.

Materials and Labour for,Non - Skid ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm,conforming to IS 15622, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement sand mortar (1:4), complete all as specified and as directed

Materials and Labour for,Non - Skid ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement sand mortar (1:4), complete all as specified and as directed

Materials and Labour for, Glazed ceramic coloured tiles, 300 X 200 X 7mm thick, conforming to IS 15622, on vertical surfaces of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick screed bed or bedding layer of cement sand mortar (1:3), complete all as specified and as directed.

M&L for water proofing treatment to existing RCC roof slab, including parapet comprising with the following courses of treatment / specification from bottom to top:- (i) Taking out old unserviceable roof treatment and roughening the same old concrete slab by wire brushing , picking, sweeping clean and washing down with water to remove dust etc. Wire brushing and cleaning top surfaces of tiles , lime terracing or cement concrete , including flashing and junction of parapets etc. (ii) Cleaned surface shall be painted with a layer of blown grade bitumen of any penetration applied hot @ 1.70 kg per sqm binded with grit or pea size gravel @ 0.006 cum per sqm and lightly tempered ( Note:- Area of flashing etc , shall be added to the roof area) . (iii) Supply and lay chicken wire mesh of size 12.5 mm x 0.51 ( 24 SWG) hexagonal construction including all laps , cutting and waste in fabric reinforcement to 40 mm thick PCC 1:2:4 type B-0 ( using 12.5 mm graded stone aggregate) as in roof padding. (iv) M&L for Screed bed or bedding layer cement plaster 15 mm thick in cement sand mortar 1:3 for laying as in roof slab with mixing of water proofing compound and surface finished fair and smooth without using extra cement. (Note: WPC shall be measured and paid for under separate items) (v) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986. (vi) M&L for APP based polymeric membrane 3 mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) shall be less applied over bituminous primer as specified above over a Application of polymeric membrance shall by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (vii) Applying one coat of aluminum paint over the APP modified membrance @ 0.11Kg/sqm.

S&F in repair 15 mm dia 3-layer PP-R P o l y p r o p y l e n e random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimocrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polyproplyne random fittings fixed complete to walls, ceilings or in floors etc.

S&F in repair 20 mm dia 3-layer PP-R P o l y p r o p y l e n e random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimocrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polyproplyne random fittings fixed complete to walls, ceilings or in floors etc.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as directed.

M&L for false ceiling with powder coated EPOXED GI grid suspension system ( E-grid T-2420 or equivalent of armstrong having load carrying capacity of 12.5 Kg/Sqm with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm C/c ) consisting of main runner 3600 mm long,cross tee 1200 / 600 mm long and wall angle. The wall angle shall be fixed on PVC dash fasteners on the perimeter of the wall with stainless steel screws at a interval 300 mm C/c.The main runners to be placed @ 1200 mm, the cross tee of 1200 mm shall be inserted in the pre cut slots of main runner at regular interval of 600 mm to form a modular grid of 1200 mm x 600 mm.Additional cross tee of 600 mm shall be placed perpendicular to the cross tee 1200 mm long to form grid of size 600 mm x 600 mm with and including 6 mm thick HPSC ( High Pressure Stem Cured) oceanic , pre-primed, self embossed , textured designer board , water , termite and fire resistant for insulation and accoustic purpose to be placed in the grid system duly suspended with 2 to 3 mm dia GI wire hangers fixed with steel dash through fasteners from purlin with butterfly clips ( weight 0.007 Kg / clip) , hold down clips ( weight 0.0035 kg / clip) with provn of light fittings and fixtures etc complete all as manufacturer's instruction ,specified and shown on page No XIV & XV of SSR Part - II ( Rates) and as directed.

Demolition of cement concrete (un reinforced) as in roofs , floors , ( other than ground floors) beams, staircases, landing,chajjas and similar suspended work and removing debris to a distance n.exc. 100 m away from site etc complete all as specified and as directed.

M&L for Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement sand mortar 1:3 etc complete all as specified and as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4.0 Sqm each etc complete all as specified and as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n. exc. 1.5 Sqm each etc complete all as specified and as directed.

S&F aluminium sliding window with powder coated ( minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed sliding shutter and one leaf gauged ( fly proofing) sliding shuttter. (ii) Opening of windows exceeding 0.90 sqm but not exceeding 1.50 sqm. (iii) Thickness and weight per meter length of aluminium frame and section of shutter as per details shown on drawing. (iv) All vertical and horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading,screws etc . (vi) Rest all as specified in drawing No. CEZ/2015/TD/007 SHEET No IR/5 , 2R/5 , 3R/5, 4R/5 & 5R/5. Note 1:- Sheet glass, aluminium grill and stainless steel wire mesh shall be measured and paid against respective items of BOQ and all other items as shown on drawing shall be included in quoted rate. Note 2:- Only opening ize of windows shall be measured and consider for payment.

S&F aluminium sliding window with powder coated ( minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed sliding shutter and one leaf gauged ( fly proofing) sliding shuttter. (ii) Opening of windows exceeding 1.50 sqm but not exceeding 2.40 sqm. (iii) Thickness and weight per meter length of aluminium frame and section of shutter as per details shown on drawing. (iv) All vertical and horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading,screws etc . (vi) Rest all as specified in drawing No. CEZ/2015/TD/007 SHEET No IR/5 , 2R/5 , 3R/5, 4R/5 & 5R/5. Note 1:- Sheet glass, aluminium grill and stainless steel wire mesh shall be measured and paid against respective items of BOQ and all other items as shown on drawing shall be included in quoted rate. Note 2:- Only opening ize of windows shall be measured and consider for payment.

S&F aluminium sliding window with powder coated ( minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed sliding shutter and one leaf gauged ( fly proofing) sliding shuttter. (ii) Opening of windows not exceeding 0.90 sqm . (iii) Thickness and weight per meter length of aluminium frame and section of shutter as per details shown on drawing. (iv) All vertical and horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading,screws etc . (vi) Rest all as specified in drawing No. CEZ/2015/TD/007 SHEET No IR/5 , 2R/5 , 3R/5, 4R/5 & 5R/5. Note 1:- Sheet glass, aluminium grill and stainless steel wire mesh shall be measured and paid against respective items of BOQ and all other items as shown on drawing shall be included in quoted rate. Note 2:- Only opening ize of windows shall be measured and consider for payment.

S&F 5 mm thick sheet glass, ordinary quality in squares not exceeding 0.50 sqm in each pane in panels of aluminium windows, ventilators etc fixed with glazing clips, rubber beading and EDPM gasket etc complete all as specified and as directed.

S&F aluminium anodised grill of design ''DG-104' pattern made out of 7.5 mm plate and finished grill having 7.5 mm width and 6 mm thick etc complete all as per manufacturer's instruction and specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and as directed.

S&F Pressed steel frames 105 X 60 mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and as directed.

S&F Pressed steel frames 105 X 60 mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and as directed.

S&F 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated etc complete all as specified and as directed.

S&F Factory made solid panel wire gauge PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling shall be of wire gauge .The wire gauge shall be wrapped on an additional square 8 mm MS soild tube . Wire gauge shall be stretched to tightened firmly,fixed in the frame at site etc complete all as specified and as directed.

S&F 35 mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, and both faces shall be covered with decorative face veener with lipping / frame to match etc complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing etc complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed tothe stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. etc complete all as specified and directed.

Material and Labour for applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surface exceeding 10 cm in width or girth including necessary preparation of surfaces complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel or iron surface exceeding 10 cm in width or girth including necessary preparation of surfaces complete all as specified and directed.

M&L for mild steel work such as in bands, straps, supports or stays for RWP , ventilating pipes , clamps , hold fasts and wall ties etc conforming to Fe 290, Grade E-165 etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 ( Using 20 mm graded stone aggregate) as in fixing / blockage of holdfast , filling in hollow door frames and bed block etc complete all as specified and as directed.

S&F aluminium anodised barrel tower bolt, extruded type, 250 mm long, complete all as specified and directed.

S&F aluminium anodised barrel tower bolt, extruded type, 150 mm long, complete all as specified and directed.

S&F aluminium handles, cast type, anodized, 150 mm size, complete all as specified and directed.

S&F aluminium handles, cast type, anodized, 125 mm size, complete all as specified and directed.

S&F mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

S&F aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed,300 mm etc complete all as specified and directed.

S&F in repai floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor , overall length of cover plate 150 mm etc complete all as specified and directed.

S&F Door magic eye , round shape including necessary cutting in door of any description etc complete all as specified and directed.

S&F rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete Fe-410-W.Gde-E-250 ,quaty A complete all as specified and as directed.

S&F Mild steel, plain, black sheet 1.25 mm in wall cladding,steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required etc complete all as specified and as directed.

S&F in repair curtain rod 20 mm dia , brass chromium plated , fancy type with bracket , fixed with wooden block / PVC through fastener wall with galvanised screws including necessary drilling and making good to disturbed surfaces etc complete all as specified and directed.

M&L for Prelaminated particle board, 12 mm thick ,exterior grade, prelaminated one side with decorative choice lamination &other side balancing white lamination,fixed with screws to timber frame work

S&F 100 mm ,brass handles , cast type , polished ,suitable for Cupboard etc complete all as specified and directed.

S&F 125 mm Hasp and staple, safety type,brass with mild steel hinge pin including bolt to hinge plate and fixed with screws etc complete all as specified and directed.

S&F 100 mm Butt hinges, cast brass,with mild steel hinge pin, bright polished and fixed, typeB-11 complete all as specified and directed

Demolition and breaking up drain pipes of internal dia 100 mm of any description (Salt glazed ware, AC or Reinforced concrete) set in cement mortar etc complete all as specified and as directed.

S & F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints fixed to walls or trench etc complete all as specified and as directed..

S & F PVC (SWR) bends of any radius with oval access door , 110 mm bore etc complete all as specified and as directed..

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for including removing debris from site etc complete all as specified and as directed.

M&L for RCC 1;2:4 type-B1, ( using 20mm graded stone aggregate) as in slab supported on wall , beams and columns in floor, roofs,landings, balcanies, canopies, deck slabs and in shelves and similar works etc complete all as specified and as directed.

M&L for Formwork to sides and soffits in rough finished flat surfaces of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed.

M&L for Mild steel TMT deformed bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

Materials and Labour for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including necessary grinding and polishing etc complete all as specified and directed.

Dismantling water tanks of capacity exceeding 250 litres but not exceeding 500 litres including float valve and removing from site etc complete all as specified and as directed.

S&F Rotational moulded polyethylene 500 ltrs capacity water storage tanks , three layered, (ISI marked) (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including 20mm dia GI medium grade over flow pipe, approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.Make:- Polycon / Polytuf / Sintex.

S&F ball brass valve, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule of size 20 mm dia etc complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed.

M&L for Brick work with subclass‘B’ bricks,straight or curved onplan exc 6m mean radius, built in cement sand mortar 1:6 etc complete all as directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement sand mortar 1:4 etc complete all as directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface other than fair face of brickwork and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 5 mm thick, cement plaster, in cement sand mortar (1:4) mixed with water proofing compound @ 3% by the weight of cement used or as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed. Note: - (Water proofing compound shall be measured and paid separately)

Materials and Labour for preparation of newly plastered surfaces of wall and applying two coats of acrylic emulsion distemper over a coat of wall primer over and including 3 mm thick wall care putty chalk whitening etc complete all as specified and as directed.

Materials and Labour for preparation of newly plastered surfaces of wall and applying two coats of exterior acrylic emulsion base premium quality matt finish weather coat anti fungal paint over a coat of wall primer over and including provn of oil putty treatment etc complete all as specified and as directed.

M&L for preparation of old or previously treated surfaces of wall and applying one coat of white wash etc complete all as specified and as directed.

Complete removal of existing treatment of wall by wire brush and washing the surface with water thoroughly and applying two coats of exterior acrylic emulsion base premium quality matt finish weather coat anti fungal paint over a coat of wall primer over and including provn of oil putty treatment etc complete all as specified and as directed.

Complete removal of existing treatment of wall by wire brush and washing the surface with water thoroughly and applying two coats of oil bound distemper over a coat of wall primer ( smooth bodied opaque finish surface ) over and including 3 mm thick wall care putty etc complete all as specified and as directed.

M&L for preparation of old or previously treated surfaces of ceiling and applying one coat of white wash etc complete all as specified and as directed.

M&L for 100 mm thick plain cement concrete 1:4:8 type D- 2, (using 40mm graded stone aggregate) as in sub base of floor , finished even and rough etc complete all as specified and as directed.

M&L for Chequered cement concrete tiles of size 20 cm x 20 cm x 25mm thick set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick screed bed in cement sand mortar (1:6) etc complete all as specified and as directed.

Supply and Fix in repairs, sinks with drainage board made of stainless steel l mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm etc complete all as specified and as directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm length etc complete all as specified and directed.

S&F in repair Bib cock , cast copper alloy,chromium plated, long body with crutch or butterfly handle , fancy type 15mm , screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make :Prayag cat part no. 8506 or equivalent make in Sona / Hindware.

S&F in repair stop valve, fancy type chromium plated screwed high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions 15 mm dia, and fixed complete all specified and as directed.Make :Prayag cat part no. 8326 / 8328 or equivalent make in Parryware / Hindware.

S&F in repair Shower rose brass chromium plated 125 mm size with swivel joints etc complete all as specified and as directed.

S&F in repair brass chromium plated tubular towel rail 600mm long between the flanges and 20mm dia etc complete all as specified and as directed.Make:- Prayag cat part no. BA-30 or equivalent make of Parryware / Hindware.

S&F in repairs soap dish , chromium plated ,fixed with CP screws etc complete as specified and directed by Engr-in-charge.Make: Prayag / Hindware / Parryware.

S&F in repairs Gratings , chromium plated , 100 mm dia, fixed in floor with neat cement slurry to match the existing etc complete as specified and directed by Engr-in-charge.Make: Prayag / Hindware / Parryware.

S&F in repair sheet glass shelf assembly consisting of 5.50 mm thick sheet glass shelf , 12 cm wide with chromium plated bracket guard and railing 60 cm long etc complete as specified and directed by Engr-in-charge.Make: Prayag / Hindware / Parryware.

S&F in repair kitchen plate rack , stainless steel , of size 24'' x 24'' x 10'' including necessary fixing / fittings and making good to the disturbed surfaces etc complete as specified and directed by Engr-in-charge.Make: Prayag cat part No P-310 or equivalent make in Hindware / Nirali.

S&F in repair Vitreous China wash down (EWC) water closet pan (pedestal pattern), white cover (excluding flushing cistern and flush pipe) but including plastic water closet seat cover closed pattern with flat bottom and cover with MS chromium plated or aluminium hinging device, fixing bolts 'P' or 'S' trap for pedestal pattern complete all as specfied and directed. Make:- Prayag cat part no. 4018 / 4019 or equivalent make of Cera / Hindware. Seat cover make of Prayag cat part no. 511 or equivalent make of Cera / Hindware.

S&F in repair PVC (Plastic polymer Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve, manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length including 450 mm long PVC connection and making connections and good to disturbed surface with cement sand mortar 1:3 complete all as directed by Engineer-in-Charge Make:- Prayag cat part no.701 or equivalent make in Pearl / Hindware.

S&F in repair Cabinet mirror of size 450 mm x 300 mm made with 5 mm thick PVC sheet coloured, glass of approved make and fixed to wall with cp screws etc complete all as directed by Engineer-in-Charge Make:- Prayag / Parryware / Hindware.

S & F in repairs Wash basin, Vitreous China white, size 550 mm x 440 mm including brackets (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified. Make: Prayag cat part no. 4647 or equivalent make in Hindware / Parryware / Johnson

S&F in repair Pillar taps, cast copper alloy,fancy type with capstan heads, chromium plated,screwed down high pressure, with orwithout lettered 'Hot' or 'Cold' withlong screwed shanks and fly-nuts,screwed for iron pipe and fixed 15 mm dia complete all as specified and as directed. Make :Prayag / Hindware / Parryware.

S&F in repair brass chromium plated Bib tap, two ways , 15 mm dia complete all as specified and as directed. Make :Prayag / Hindware / Parryware.

S&F in repair 2-1 health faucet with 1.5 m PVC tube,and necessary hook fixed to wall with CP screws etc complete all as specified and as directed. Make :Prayag / Hindware / Parryware.

S&F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 etc complete all as specified and as directed.

Material and Labour for applying one coat of synthetic enamel paint on old or previously treated surfaces of wooden, exceeding 10 cm in width or girth including necessary preparation of wooden surfaces complete all as specified and directed.

Surface dressing n.exc not exceeding 15 cm deep in soft/loose soil complete all as specified.

Excavating in trenches n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil etc complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 Cm thick as in soft/loose soil etc complete all as specified and as directed.

Removing excavated materials (soil) to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed.

M&L for Hardcore of crushed stone, gauge n exc 63mm, deposited, spread and levelled well in layers n exc 15cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation , filling and mass concrete etc complete all as specified and directed

M&L for RCC 1:1.5:3 type A-1, nominal mix, ( using 20mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete etc complete all as specified and as directed.

M&L for RCC 1:1.5:3 type A-1, nominal mix, ( using 20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts etc complete all as specified and as directed.

Formwork to sides of concrete of rough finished on flat surfaces in foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Formwork in rough finished surfaces of of rectangular, square or polygonal sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed.

M&L for Mild steel TMT deformed bars, 5 to 8 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

S&F mild steel work as in tubular trusses , purlins, and posts etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 etc complete all as specified and as directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long and dia of neck 20 mm etc complete all as specified and as directed.

S&F Mild steel plates, plain or chequered, 5mm thick or over in thickness as per Fe 410-W (Gde-E-250) quality-A including necessary drilling holes in plates , bolting , riveting as required etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed.

M&L for 100 mm thick plain cement concrete 1:2:4 type B-2, (using 40 mm graded stone aggregate) as in floor , including spike rolling to surfaces or making impressions of expanded metal ,whilst the concrete is green etc complete all as specified and as directed.

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:4) on surface other than fair face of brickwork and finishing surface even and smooth without using extra cement, complete all as specified and directed.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with Grade 'A' sealing compound etc.complete all as specified and directed.

M&L for preparation of newly or previously untreated surfaces of wall and applying three coats of cement base paint etc complete all as specified and as directed.

M&L for plain cement concrete 1:3:6 type C-1 ( using 20 mm graded stone aggrgate ) as in foundation , filling and mass concrete and embedding of post in natural ground etc complete all as specified and as directed.

Supply and filling in dry and clean river sand in cable trenches before and after the cables are laid, as in sand cushioning to cables, complete all as specified and as directed.

Supply and laying common burnt clay building bricks, sub-class‘B’ designation 75, old size bricks, in cable trenches, as cable protection, complete all as specified and directed.

Supply,laying, jointing and testing of , XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 16 sqmm 2 core with aluminium lugs etc complete all as specified and directed.

Supply and Laying galvanized steel tubing, 40 mm bore, light grade in trenches or fixed to poles / Walls for cable protection including necessary cutting in road / hardstanding of appropriate depth and width and making good of the disturbed portion with PCC 1:3:6 type C-1 ( using 20 mm graded stone aggregate etc complete all as specified and directed

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, lamp holders, regulators, switch, socket outlets, bell push, ceiling rose etc removing material to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls with cement sand mortar (1:6) and white/colour wash to match with existing surfaces etc complete all as directed by Engineer -in -Charge .

Taking down copper/aluminium sub main wiring complete and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L Point wiring with single runs PVC insulated FRLSH grade, 1100V grade cable with multistranded copper conductor of size 1.5 Sqmm (Nominal area) (ISI Marked) drawn in and including PVC Casing capping of suitable size with all fittings and accessories including PVC rectangular board of suitable size and drawing continuous earth wire of PVC insulated FRLSH grade, unsheathed stranded copper conductor of size 1.5 Sqmm (ISI Marked) as continuous earth wire terminated in and including sunken box for following type of point wiring including making good disturbed of wall complete all as specified in SSR Part-I, 2009 and Part-II, 2010 and as directed by Engineer-in- Charge for one light point / one 3 pin socket outlet 5/6 Amps and one bell point on independent board controlled by one one way switch.

All as per item No 2 above but for one 2/3 pin socket outlet 5/6 Amps point on same board etc complete all as directed by Engineer -in -Charge .

All as per item No 2 above but for one 2/3 pin socket outlet 5/6 Amps point on independent board etc complete all as directed by Engineer -in -Charge .

All as per Item No. 2 here-in-before but with FRLSH grade, (ISI mark) PVC insulated and unsheathed two run multistranded copper conductor of size 4.0 Sqmm for one power point of 3 pin 15 Amps on independent board including FRLSH grade (ISI mark), PVC insulated, unsheathed one run multi-stranded copper conductor of size 4.0 sqmm green in colour as earth continuity conductor connected to common earth dolly complete all as specified and directed.

Material and labour for sub main wiring with two single core 6.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 6.0 sqmm green colour as earth lead including PVC casing capping of suitable size complete all as specified and directed. (Note: Two runs of 6.0 sqmm cable , one run of earth wire of 6.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- Finolex / KEI /Havells, PVC Casing Capping- Presto plast/Finolex/Kalinga.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, flush type, one way 5 Amps complete all as specified and directed.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, flush type, one way 15 Amps complete all as specified and directed.

Supply and fix Socket outlet (ISI marked), 2/3 pin and 5 Amps, flush type, , 240 volts complete all as specified and as directed.

Supply and fix Socket outlet (ISI marked), 2/3 pin and 15 Amps, flush type, multipurpose , 240 volts complete all as specified and as directed.

S&F Ceiling rose, 3 terminals PVC/polycarbonate, isolated body complete all as specified and directed.

S&F Electronic fan regulator flush type , 4 step type , 120 W , AC , 240 volts , 50 Hz , etc complete all as specified and as directed.

Supply and Fix LED wall mounting fixture made up of polycarbonate sheet ,B-22 base ,with 01 x 15 watt LED bulb including necessary electric connection etc complete all as specified and directed.Make:- Havells Cat part No LHFOFUE1TZ1WO12 or equivalent make in Bajaj / Crompton / Philips.

S&F lamp holder, insulated body, with back plate for batten fitting complete all as specified and as directed.

S&F LED bulb 15 watt energy efficient etc complete all as specified and as directed.Make:- Havells / Bajaj / Philips

S&F Call bell, ding dong, AC, 230 V, Single pole (ISI marked) completed all as specified and directed.

S&F Decorative ultra slim linear LED batten light fitting with co extruded polycarbonate body enviornmental friendly, energy efficient , E-LITE LED GREEN suitable for 18 watt LED 6000K , 240 volts LED tube light ( single side connection ) including 1 x 20 watt LED tube rod etc complete all as specified and directed.Make:- Wipro Cat part No. LL13-181-65SESL Havells Cat Part No:LHEXBLP7UN1W018 / Philips Cat part no.DX18Wor equivalent make in Havells / Crompton / Bajaj.

S&F Decorative ultra slim linear LED batten light fitting with co extruded polycarbonate body enviornmental friendly, energy efficient , E-LITE LED GREEN 9 watt LED 6000K , 240 volts LED tube light etc complete all as specified and directed.Make:- Wipro / Havells / Crompton / Bajaj.

S&F new generation energy saving building security light luminiries housing of versatile pressure die cast aluminium IP-66 with high power LED light 25 watt 230 volts 50 Hz with ballast / charging unit including all accessories , pre-wired including connecting up with 2.5 sqmm multi stranded aluminium conductor 2 core cables not less than 3 m length ,fixed to pole / wall etc and testing etc complete all as specified and directed.Make:- Wipro Cat part No LR02-291-XXX-57-XX or equivalent make in Havells / Crompton / Bajaj.

S&F Exhaust fan AC single phase 230 / 240 volts of weep 300 mm with plastic self closing louver and making necessary electric connection with flexible copper conductor cable 1.5 sqmm 3 core PVC insulated including cutting holes of appropriate size in brick wall or concrete wall and making good to disturbed surfaces with cement sand mortar 1:3 with necessary paint /white wash to match the existing etc complete all as specified and as directed. Make:- Usha / Crompton / Havells / Bajaj.

S&F in repair MCB DB SPN double door, IP-43 with 200 amps rated busbar ,earth bar , neutral links complete including blanking plates etc complete all as specified and directed. [Make:- L&T ,Cat No.DBSPN008DD or equivalent Model of Make Legrand/Siemens]

S&F in repair MCB SPN 40 amps 240 volts , 50 Hz , breaking capacity 10 kA ''C'' series etc complete all as specified and directed. Make:-L&T / Legrand / Siemens

S&F in repair MCB SP 6-32 amps 240 volts , breaking capacity 10 kA ''C'' series etc complete all as specified and directed. Make:-L&T / Legrand / Siemens

Materials and Labour for earthing complete with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge earth plate at a depth not less than 1.5M below normal ground level connected to galvanised steel strip 25/4 mm earth lead . by means of bolts, nuts check nuts and washers of galvanised steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm centre to centre both ways, with one handle for lifting made out of 8 mm dia. MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing medium grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009)

A M CHOUDHURY AND CO