REPAIRS TO ROOF CEILING FLOORING WALL PLASTERING DOOR WINDOW SCANTLING TO BLDG NO A B C D E G I J AND K ZONE AT RMS

Amount

Demolition of cement concrete (un-reinforced) in ground floors and pavings n.exc 15 cm thickness (below or above GL) and removing rubbish of the premises complete all as specified and as directed.

Demolition of cement concrete (reinforced) in any position and in any description such as manhole, septic tank cover slab ( cast in situ or precast ) , complete all as specified and as directed.

M&L for R.C.C (1: 2 :4) type B1 (Nominal Mix) using 20 mm graded stone aggregate as in slab supported on walls , beames and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc.complete all as specified and as directed.

M&L for Use and waste of formwork to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick , rough finished surfaces of concrete, flate, complete all as specified and directecd.

Demolition of brick work or stone/boulder masonry built in cement mortar ,complete all as specified and directed.

M&L for brick work with sub class ‘B’ bricks , straight or curved on plan exc 6 metre mean radius as in full brick thick walls built in CM(1:6) using old size bricks complete all as specified and as directed.

M&L for brick wrok with sub-class 'B' bricks, straight or curved on plan to any radius, built in CM (1:4) using old size bricks in half brick thick walls complete all as specified and as directed.

Dismantling timber scantling 40 Sqcm and over in section, in any position, un -framed work complete all as directed.

Dismantling wooden boarding, any description, fixed in any position with nails complete all as directed.

Second class hard wood timber scantling 40 Sqcm and over in section, in any position, clean sawn ,un -framed work, fixed with nails , complete all as specified and directed.

S & F Second class hard wood timber boarding ,20 mm thick, planed one side with butt jointsc, fixed with nails , complete all as specified and directed.

S & F 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and directed.

Taking down chowkats including shutter (without taking off shutter from the frame) area not exc 1.50 Sqm each complete all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exceeding 1.50 Sqm and not exceeding 4 Sqm each and removing complete all as directed.

Taking down shutters of any description n.exc 1 Sqm each complete all as directed

Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm eachcomplete all as directed

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue and pinned at joints complete all as specified and as directed.

S&F for second class hardwood 30 mm thick plain, framed, panelled shutter (two panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F for second class hardwood glazed and skeleton door shutters, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats complete all as specified and as directed.

S&F for second class hardwood glazed and skeleton window and ventilator shutters, 30mm thick, open rebated and prepared to receive glass, gauze, etc. provided with stiles and rails, edge of framing plain, chamfered or rounded, fitted with cut and mitred beeds for securing glass etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (b); supplied and fitted to chowkats complete all as specified and as directed.

S&F for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling & fixing in opening complete all as specified and as directed.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per manufacturer,s instruction and directed.

Taking down Aluminium window shutter with frame (without taking off shutter from the frame) area not exc 1.50 Sqm each complete all as directed.

Taking down Aluminium window shutter with frame (without taking off shutter from the frame) exceeding 1.50 Sqm and not exceeding 4 Sqm each and removing complete all as directed.

S&F Anodised Aluminium work in any position such as door frames, window frames, grills , guard bars etc with one or more rebates incl necessary joining cleats for fixing etc complete all as specified and directed

S&F for anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section of size 40 x 18 x 1.29mm thick including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed

S&F for anodised aluminium sliding window shutters without sash bar, thick including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, rollers etc. complete all as specified and directed

S&F anodised aluminium door shutters, aluminium section weighing 0.55 kg/m incl necessary joining cleats, glazing clips, rubber neoprene packing handles 2 Nos in each door, hinges anodised aluminium snap beading screws etc, complete all as specified and directed.

S & F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and as directed.

S&F steel windows with side hung shutters including pintal type hinges with MS handles and tower bolts complete without glazing bars, as fly proof shutters with one shop coat of primer complete all as specified and directed.

S&F Aluminium, anodised, barrel tower bolt 200mm long of extruded section and fixed complete as specified and directed.

S&F Aluminium, anodised, barrel tower bolt 150mm long of extruded section and fixed complete as specified and directed.

S&F Aluminium, anodised, barrel tower bolt 100mm long of extruded section and fixed complete as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 100 mm size complete as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 75 mm size complete as specified and directed.

S&F 150 mm size aluminium alloy handles, fabricated type, anodised ,complete all as specified and as directed

S&F 100 mm size aluminium alloy handles, fabricated type, anodised ,complete all as specified and as directed

S&F aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy and fixed length of bolt 300mm complete all specified and as directed.

S&F Mortice lock,vertical type Brass 2 levers, size 100 mm incl three set of key fixed in repairs complete all as specified and directed.

S&F 300mm ordinary mild steel rat tail rod patttern springs includding roller and roller plate complete as specified and directed.

S&F double action floor spring hydraulically regulated made upof minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainlessl steel cover governing pivot made of brass other parts made of mild steel heavyduty and fixed ,complete all as specified and directed.

S & F for door closer hydraulically regulated ( Aluminium extruded section) designated No. 2 universal type, suitable for door shutter upto 701 to 850 mm in width & of weight between 36 to 60 Kg.fixed in repair complete all as specified and directed.

S & F for door closer hydraulically regulated ( Aluminium extruded section) designated No. 2 universal type, suitable for door shutter upto 701 to 850 mm in width & of weight between 36 to 60 Kg fixed in repair complete all as specified and directed.

S&F galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples, complete as specified and directed..

S&F galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples fixed in repairs, complete as specified and directed..

M&L for second class hardwood beads, straight (any size) for fixing galvanised MS wire cloth, renewed , including mitres etc, complete all as specified and directed.

M&L TMT steel bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete as in reinforcement to concrete all as specified and as directed.

S&F of mild steel framed work such as grills gratings etc with ends of bars shouldered and or rivetted or forged into spikes framed guard bars and similar work conforming to Fe-290-0 Gde E-165 complete all as specified and as directed.

Welding or repair of steel window/doors with hinged or peg stay, shash bar and guard bars etc with complete each window work exc 2.5cm but n exc 5cm in length n exc 6mm in thickness, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as directed

Dismantling asbestos cement (Corrugated or semicorrugated) sheets in roof covering, complete all as directed.

S&F asbestos cement corrugated or semi corrugated sheet 6mm thick in roofs etc fixed with “L” or ‘J” type or cranked hook bolts ,complete all as specified and as directed

All as per item No 52 hereinbefore but except sheets ( Note: asbestos cement corrugated or semi corrugated sheet retrived from item No 51 here in before shall be reused)

S&F 6mm thick asbestos cement two piece adjustable serrated ridge for corrugated or semi corrugated sheets fixed with ‘L’ hooks or ‘J’ type cranked bolts complete all as specified and as directed.

S&F 0.63mm thick galvanised corrugated mild steel sheeting, with two corrugation side lap fixed with GI 'L' type or 'J' type or cranked hook bolts in roof, walls etc with grade of zinc coating as per IS complete all as specified and as directed.

All as per item No 55 hereinbefore but except sheets ( Note: CGI sheet retrived from item No 50 here in before shall be reused)

S&F Mild Steel, plain, black Sheeting 0.80mm thick as in eaves and barge boards fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles,stopped ends etc , complete all as specified and as directed.

S&F 0.50mm thick prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour as approved of 550 Mpa tensile strength as in roof covering/ cladding to wall etc. fixed with self tapping screws complete as specified and directed

S&F 0.50 mm thick Prepainted galvalume aluminium zinc coating GI based plain steel sheet any colour as approved of 550 Mpa tensile strength as in ridges etc fixed with self drilling and self tapping screws, complete all as specified and directed.

Dismantling wall and ceiling boards (fibre pulp insulation etc) or insulation boards, slabs, blankets any thickness, incl cover fillets, complete all as directed

S & F for 4 mm thick of size 600x600mm HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board Classic to be fixed aluminium grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size complete all as specified and directed.

S&F for 4 mm thick veneered decorative Plywood (no of ply 05), grade-I (with BWR resin) with decorative face veneers on one face, fixed with screws to timber frame work complete all as specified and directed.

Dismantaling floor,hearth or wall tiling including cement mortar bedding (but not backing),removing serviceable tiles to store and rubbbish off the premises.complete all as directed

M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded aggregate) as in paving/plinth protection , laid in alternate bays, finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 40mm thick plain cement concrete 1:2:4, type B1, (using 20mm graded stone aggregate) as in floor finished the surface even and smooth using extra cement complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular), area of each tiles exc 0.06 Sqm but not exc 0.11 Sqm in floors etc set and jointed in neat cement slurry and piinted in white/coloured cement to match including 15mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

All as per item No 66 here-in-before but as in skirting/ dado for vertival surfaces ,including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular), area of each tiles exc 0.11 Sqm but not exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and piinted in white/coloured cement to match including 15mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

All as per item No 68 here-in-before but as in skirting/ dado for vertival surfaces ,including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 300mm x 200mm x 7mm thick on vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match with the existing, ,including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

S&F vitrified ceramic tiles 10 mm thick light shade (square/rectangle) area of each tile not exe 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white/coloured cement to match including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

All as per item No 71.00 here in befroe but on vertical surfaces including rendering 10mm thick in cement mortar 1:4 ,complete all as specified and as directed.

Taking down cement plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. complete all as directed

M&L for 10 mm thick rendering on fair faces of concrete surfaces in ceiling in cement mortar 1:4 finished surfaces even and smooth (without using extra cement) complete all as specified and as directed.

M&L for 15mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6 finished surfaces even and smooth (without using extra cement) complete all as specified and as directed

Demolition of reed lathing single or double including battens and plaster or chicken wire lathing ,complete all as directed.

M&L GI wire netting 0.71 mm dia and 12 mm mesh lathing in to reed in walls incl all laps cutting and waste fixed in repairs complete all as specified and directed

M&L for rendering 15 mm thick in CM 1:4 on one side of lathing finished even and smooth without using extra cement, complete all as specified and as directed.

M&L for rendering 12 mm thick in CM 1:6 on other side of lathing finished even and smooth without using extracement complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls and applying one coat of white wash , complete all as specified and as directed.

M&L for preparation new surface of wall and applying two coats of distemper oil emulsion over a coat of 3mm thick wall care putty filling complete all as specified and directed.

M&L for complete removal of existing treatment of wall and applying two coats of distemper oil emulsion over a coat of 3mm thick wall care putty filling complete all as specified and directed.

M&L for preparation of old decorated surface of wall and applying one coat of distemper oil emulsion , complete all as specified and as directed.

M&L for preparation on newly plastered surfaces on wall and applying two coats of cement based paint over priming coat of alkali resistant priming paint ,complete all as specified and as directed.

M&L for preparing old painted surfaces of wall by washing, rubbing down and stopping of painted surfaces and applying a coat of cement base paint ,complete all as specified and as directed .

Hacking Out Old Broken Glass (any thickness, size, quality or description) from Wooden Frames, Glazed with Putty or fixed with Beads, complete all as specified and as directed.

S & F 3 mm thick, figured glass,pin head type and glazing with oil putty in squares in exc 0.5 sq.m in each pane complete all as specified and as directed.

S&F 3mm thick sheet glass , ordinary quality and glazing with oil putty in square n.exc 0.50 sqm each panes complete all as specified and as directed.

S & F 5.5 mm thick, thick sheet glass , ordinary quality and glazing with oil putty in squares in exc 0.5 sq.m in each pane complete all as specified and as directed.

S & F for Sun control 25 micron reflective type sticked to glass panes as per instructions of manufactures, complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description, over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint (1st quality) over priming coat of pink primer complete all as specified and as directed.

M&L for preparation of old decorated wooden surfaces of any description, over 10cm in width or girth, not otherwise described,, and applying one coat of synthetic enamel paint (1st quality) complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description and French polishing on surfaces including a coat of wood filler complete all as specified and directed.

M&L for preparation of old decorated wooden surfaces of any description and French polishing on surfaces including a coat of wood filler complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint (1st quality) over priming coat of red oxide zinc chrome primer complete all as specified and as directed.

M&L for preparation of old decorated steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described, and applying one coat of synthetic enamel paint (1st quality) , complete all as specified and as directed.

M&l for preparation old decorated surfaces on wall and applying one coat of weather exterior acrylic emulsion wall paint, complete all as specified and as directed.

S&F for Vitreous china squatting pan ‘orissa’ pattern of size 580X440mm white, with P or S trap, integral foot rest, indian rubber cones (Nozzles of WC Pan), joints between flush pipe and socket of WC pan (excluding flushing cistern and flush pipe), fixing with and including provision of 150 mm thick lime concrete bedding,fixed in repair, complete all as specified and as directed.

S&F vitreous china wash hand basin, white, flat back, size 550x 400 mm including a pair of MS brackets and cutting for pinning in ends of brackets but including chain and plug and porcelain stopper, MS chromium plated grating, PVC waste pipe, fixed in repair, complete all as specified and as directed.

S&F PVC flushing cistern 10 litre capacity, low level valve less, symphonic action type, white, with inlet, ball valve, float and handle including 32mm dia PVC flush pipe, a pair of cast iron brackets duly painted/ recting stand including cutting and pinning in ends, making good disturbed surfaces in cement mortar 1:3,, fixed in repair,complete all as specified and directed.

S&F PVC connection 15mm size with PTMT nuts, of 450 mm length fixed in repairscomplete all as specified and directed.

S&F brass chromium plated shower rose 125 mm size , with or without swivel joints, fixed to steel pipe or union, complete all as specified and directed. (MAKE :Jaquar/ Kohler/ Marc/ Grohel/ Lauret/ Crabtree )

S&F 15mm dia steel water tubing, galvanised, medium grade, with all fittings and fixed to wall and ceiling or laid in floor in old/new position ,including taking down the old unserviceable pipe,complete all as specified and as directed.

S&F 20 mm dia steel water tubing, galvanised, medium grade, with all fittings and fixed to wall and ceiling or laid in floor in old/new position ,including taking down the old unserviceable pipe,complete all as specified and as directed.

S&F Bib tap, 15 mm bore , long body cast copper alloy(fency type), chromium plated ,'with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule a ,fixed in repair complete all as specified and directed. (MAKE:- Prayag /Cera/Hindware/ Century)

S&F Stop valves, 15mm bore, ,chromium plated, serewed down high pressure, with crutch or butter fly handle, screwed both ends for iron pipe or for union fixed in repair , complete all as specified and directed. (MAKE:- Prayag Cat No 7326 or equivalent of make Cera/Hindware/ Century)

S&F angle Stop valves, 15mm bore, ,chromium plated, serewed down high pressure, with crutch or butter fly handle, for iron pipe or for union a , complete all as specified and directed. (MAKE:- Prayag or equivalent of make Cera/Hindware/ Century)

S&F for 15mm dia of pipe stop valves, concealed type and chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for Unions fixed in repair,complete all as specified and directed.

S&F Bib tap, 15mm bore, standard of PTMT, any colour screwed for iron pipe ,Minimum weight 90gms), fixed in repair complete all as specified and directed.

Taking out old drain pipes PVC (SWR) pipe 110mm/ 75 mm in any length with rubber ring joints ,fixed on wall , complete all as directed.

S&F 110 mm PVC (SWR) pipe single socketed in any length with rubber ring joints ,fixed on wall , complete all as specified and as directed.

S&F 75 mm PVC (SWR) pipe single socketed in any length with rubber ring joints ,fixed on wall , complete all as specified and as directed.

S&F Stack clamps for 75 mm bore pipe made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F Stack clamps for 100 mm bore pipe made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

m/s chakraborty enterprises

M/S RAHUL TRADING CO.

commercial enterprises

das enterprises

KAILASH KUMAR LADHA

SK SINGH