SPECIAL REPAIRS TO CERTAIN OTM AND MD ACCN AT VSN NAGPUR

Amount

B/R PORTION

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition), in chajjas, beams and similar suspended work including floor finishes complete all as specified and directed.

Demolition floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removal of debris to a distance exceeding 100m but not exceeding 250m all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Material and labour for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 all as specified and directed.

Material and labour for rendering 15 mm thick in CM 1:6 over brick surfaces, finished even and smooth without using extra cement all as specified and directed.

Material and labour for preparation of newly plastered wall surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed.

Material and labour for complete removal of existing treatment and preparation of surfaces including filling the cracks if any on surfaces of wall and applying two coats of Oil bound distemper over a coat of wall care putty complete all as specified and directed.

Material and labour for preparing old painted surfaces by washing, rubbing down and stopping of distempered and painted surfaces and applying a coat of distemper oil emulsion on ceiling surfaces complete all as specified and directed.

Material and labour for Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

Material and labour for glazed coloured ceramic tiles of size 300mm x 450mm, 7mm thick, laid on vertical surfaces such as skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tile complete all as specified and directed .

Material and labour for double charged Vitrified ceramic tiles, 10mm thick (square/rectangular) area of each tile exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tile complete all as specified and directed.

Material and labour for double charged Vitrified ceramic tiles, 10 mm thick (square/ rectangular) area of each tiles exceeding 0.36 sqm but not exc.0.42 sqm, laid on vertical surfaces such as skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tile complete all as specified and directed

Material and labour for rendering 10 mm thick as in backing coat on fair face of brick walls/ concrete surfaces for tiles in CM 1:4 complete all as specified and directed

Material and labour for Screed bed or bedding layer of mortar 15mm thick in cement mortar 1:6 for laying floor tiles all as specified and directed

Material and labour for machine cut cudappah stone slab, 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed

Material and labour for rounding to edges of stone slabs on edge, such as in steps, cooking platform and other similar situations all as specified and directed

Material and labour for Baroda green granite (or any type) tiles, 15 mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing all as specified and directed.

Supply and fix sinks made of stainless steel 1.00mm thick for kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm all as specified and directed.

Taking up or down steel tubing 15mm dia and connections, complete all as specified and directed.

Taking up or down steel tubing 20mm dia and connections, complete all as specified and directed.

Refixing old serviceable steel tubing, 15mm dia obtained from taking down and connecting in new or old position (Walls, ceiling, floors, etc.) with necessary provision of new fittings all as specified and directed.

Refixing old serviceable steel tubing, 20mm dia obtained from taking down and connecting in new or old position (Walls, ceiling, floors, etc.) with necessary provision of new fittings all as specified and directed.

Supply and fixing GI tubing,15mm dia 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Supply and fixing GI tubing,20mm dia 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Supply and fixed in repairs, 40mm dia low density polyethylene pipe (LDPE) of pressure rating 6 Kgf/Sqcm fixed complete in wall, floor etc all as specified and directed.

Supply and fixed in repairs, 40 mm dia, Waste fittings, brass chromium plated for glazed ware sinks, wash basins etc., with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

Supply and fix, waste coupling of PTMT 40mm (half or full threaded) suitable for kitchen sink. (Minimum weight 32mm- 45gms/40mm-60 gms) all as specified and directed.

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings all as specified and directed.

Material and labour for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour as approved by GE, having tensile strength of 550Mpa as in roof covering /cladding to wall, fixed with self tapping screws all as specified and directed.

Material and labour for prepainted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall , fixed with self tapping screws as specified.

Taking down cement or cement lime plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc.all as specified and directed.

Material and labour for rendering 15 mm thick in CM 1:4 on brick or concrete surfaces even and smooth without using extra cement mixed with water proofing compound @ 3% by weight of cement and finish surface fair and even all as specified and directed Note : WPC shall be measured and paid separately

Material and labour for preparing new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primer all as specified and directed

Taking down chowkat with shutter (without taking off shutters from the frame) exceeding 1.5sqm but not exceeding 4 sqm each all as specified and directed.

Taking down chowkat with shutter (without taking off shutters from the frame) not exceeding 1.5sqm each all as specified and directed.

Taking down shutters of any description not exceeding 1.00 sqm each all as specified and directed.

Taking down shutters of any description exceeding 1.00 sqm and not exceeding 2.00 sqm each all as specified and as directed.

Supply and fix IInd class HW plain solid, straight, chowkats and frame, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints all as specified and directed.

Supply and fix 35 mm thick second class hard wood factory made framed panel shutters (two panels) with panels of timber flat on both sides (feather edge) or veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part-I) kiln seasoned and chemically pressured treated all as directed.

Supply and fix, 30mm thick flush door shutter soild core construction with block board core and plywood face panels commercial type on both sides complete all as specified and as directed.

Supply and fix, aluminium anodised sliding door bolt 300 mm long with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extruded sections or cast aluminium alloy and fixed all as specified and directed.

Supply and fix, Floor door stopper of size 150 mm aluminium alloy body, double and tongue anodised with rubber shoe and fixed all as specified and directed.

Supply and fix, 200 mm long aluminium anodised barred tower bolt of extruded section and fixed all as specified and directed.

Supply and fix, extruded aluminium alloy handle 150 mm long fabricated type anodised and fixed all as specified and directed.

Supply and fix, butt hinge 100mm long, medium weight, cold rolled mild steel all as specified and directed.

Dismantling boarding, any description, fixed in any position with screws all as specified and directed.

Material and labour for providing and fixing Gypsum Board 12 mm thick in ceiling fixed with screws as per manufacturer's instructions all as specified and directed.

Supply and fix, GI frame work for seamless ceiling (Size of grid 605 x 605mm) comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel at 457mm centre to centre and Hangers 6mm dia GI wire (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long complete all as specified and directed

Material and labour for 1mm thick putty finish on wall surfaces with wall care putty and applying two coats of OBD all as specified and directed

Supply and fixed in repairs towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden plastic cleat (minimum weight 190 gram) all as specified and directed.

Supply and fix, powder coated Anodised aluminium frame and shutter for doors, windows, ventilators with one or more rebates including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws etc.(minimum thickness of powder coating 50micron) complete all as specified and directed

Material and labour for providing post constructional anti termite treatment by making hole of 12 mm dia to be drilled at 300 mm apart at the junction of external and internal wall with floor and construction and expansion joints if any at ground floor only and pouring the emulsion @ 1 Ltr / hole and plugging the same with white cement to match the existing surface complete all as specified and directed.

Material and labour for providing post construction anti termite treatment at points of contact of wood work such as chowkhets of wooden doors windows ventilators loft ward robes etc in oil or kerosene based solution @ 0.50 Ltr's / hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm C/C and sealing the same all as specified and directed.

Material and labour for preparation of old painted steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying one coat of synthetic enamel paint all as specified and directed.

Material and labour for complete removal of existing treatment on walls and applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces all as specified and directed.

Supply and fix, Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of stainless steel wire cloth i.e. panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly all as specified and directed.

Supply and fix, stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples all as specified and directed.

Supply and fix, solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with mild steel Square tube with single side prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet & fixed in position as per manufacturer's instruction all as specified and all as shown on drawing on Srl page No 160 of SSR Part-II 2020 (Rates)

Supply and fix, factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement and fixing in the frame at site as per specification & drawing all as specified and directed.

Supply and fix, MS rolled framed work such as grills, gratings, etc, with ends of bars shouldered and or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders framed balusters walk ways, railings, framework of water tanks and similar work conforming to Fe 290. Gde-E- 165 all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided all as specified and as directed

Supply and fix, sheet glass 4mm thick, ordinary quality not exceeding 0.5 sqm in each pane and in square and glazing with oil putty all as specified and as directed.

Supply and fix, pin head type glass 4mm thick, ordinary quality not exceeding 0.5 sqm in each pane and in square and glazing with oil putty all as specified and as directed.

Material and labour for preparing new surfaces of steel of any description not otherwise described 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed

Taking down carefully existing bitumen tar felt including plaster, concrete/brick coba /tiling from the roof /parapets till RCC slab and roughening the surface, wire brushing, cleaning and washing with water etc., and removing the rubbish to a distance exceeding 500m but n.exc 1Km & depositing where directed .

Taking down carefully existing bitumen tar felt including plaster from the roof /parapets and roughening the surface, wire brushing, cleaning and washing with water etc., and removing the rubbish to a distance exceeding 500m but n.exc 1Km & depositing where directed .

Material and labour for roof treatment on RCC roof slab complete as mentioned below, all as specified and directed:- (i) Cleaning the concrete surfaces of RCC roof slab as obtained after demolition/taking down of existing water proofing treatment thoroughly with wire brushes, washed and dried. (ii) Checking the roof slab by flooding test with water till total elimination of leakage/seepage/ dampness all as specified in SSR Part-I (after ascertaining location of leakage/seepage/ dampness, carrying out treatment vide Srl Item No.71 here-in-after of pressure grouting shall be operated at the required locations). (iii) Brushing surface with neat cement slurry at the rate of 3.00kg of cement per Sqm. (iv) Cleaning the plastered roof surfaces and applying a coat of bitumen primer @ 0.3 kg/sqm on top of dry surface and applying hot blown bitumen at the rate of 1.2Kg/sqm. (v) Laying APP modified polymeric membrane 3mm thick with non woven polyester core laid and bonded to the sub-strata and over-laps shall be sealed/fused by flame "torch', application method all as per manufacturer's instructions.

Material and labour for application of bitumen base aluminium paint @ 0.2 ltr/Sqm in two coats over APP modified polymer membrane as per manufacturer's instructions all as specified and directed

Material and labour for PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in filleting and benching slightly rounded off etc. Including necessary form work, if any, complete all as specified and directed.

Material and labour for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate to fill undulations over RCC roof slab to achieve uniform slope complete all as specified and directed.

Material and labour for rendering over roof slab 10 mm thick in CM 1:3 on concrete surfaces mixed with water proofing compound @ 3% by weight of cement and finished surfaces fair and even all as specified and directed. Note : WPC shall be measured and paid separately

Material and labour for grouting in roof through PVC nipples at a spacing of 45 to 60cm C/C including drilling injection points to a depth of 75-100mm, providing 10mm dia PVC nipples and pressure grouting using with and including cement mixed with plasticizing admixture like FOSROC (model CEBEX100) or PIDILITE (model 207 PIDICRET 8AM) @ 225gms/50kg of cement to fill up all capillaries/ voids/ honeycombing areas inside concrete with pressure of 2 to 4 Kg/Sqcm and continued till refusal. After grouting, nozzles to be sealed with the sealing compound/mortar etc, all as per manufacturers instructions and as directed. Note : After ascertaining the location of leakage/ seepage/dampness under Srl item No.66 here-in-before, this item shall be operated at the required location.

Disconnecting existing PVC water tanks of capacity exc 250 litres & n. exc 500 litres setting aside (or lowering) for repair work and hoisting, reconnecting, refixing in the same position complete all as specified and directed.

Disconnecting existing PVC water tanks of capacity exc 500 litres & n. exc 1000 litres setting aside (or lowering) for repair work and hoisting, reconnecting, refixing in the same position complete all as specified and directed.

Dismantling existing PVC water tanks of capacity exc 500 litres & n.exc 1000 litres capacity all as directed

Dismantling existing PVC water tanks of capacity exc 250 litres & n.exc 500 litres capacity all as directed

Supply and fix, 500 litres capacity rotational moulded polyethylene water storage tank, triple layered (Cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed .

Supply and fix, 1000 litres capacity rotational moulded polyethylene water storage tank, triple layered (Cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed .

Supply and fixed in repairs, 20mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all as specified and directed.

Supply and fixed in repairs, 20mm bore ball brass valve high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed all as specified and directed.

Supply and fix, ornamental type powder coated mild steel curtain rods of dia 25mm and thickness of 1mm including brackets etcall as directed

Supply and fixed in repairs, PVC connection 15 mm size with PTMT nuts of length 450 mmall as specified and directed.

Supply and fixed in repairs, vitreous china wash hand basin, white, flat back, size 550 X 400 mm, erecting on existing CI brackets all as specified and directed. Note : If above mentioned size is not available in the market, the next immediate higher size shall be provided by the contractor without extra cost.

Supply and fix, pillar taps 15mm bore dia of pipe cast copper alloy with capstan heads; chromium plated screwed down high pressure with or without lettered HOT or COLD with long screwed shanks and fly-nuts screwed for iron pipe and fixed complete all as specified and directed.

Supply and fixed in repairs, PVC (SWR) 110 mm bore pipe, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

Supply and fixed in repairs, 15mm bib taps fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule and fixed all as specified and directed

Supply and fixed in repairs, 15mm dia concealed angular stop valves, fancy type, chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or union and fixed all as specified and directed

Supply only integral water proofing compound.

Material and labour for Grubbing up tree trunk including cutting of trunk protruded over brick wall, chajja, roof digging out roots filling hole with concrete 1:2:4, type B0 (using 12.5mm graded stone aggregate) girth of tree exc 30cm and n exc100cm and removing of unserviceable material to a distance n exc50m and clearing site complete all as directed.

Material and labour for repairs to ends of chajja upto 600 mm wide and 100 mm thickness by removing the old loose concrete material, clearing the reinforcement and fishing the surface, applying epoxy base resin of manufacturer Pidicrete or Chouksi and make good with concrete 1:1.5:3 as required to exiting broken surface and fair and even in cement mortar 1:3 with epoxy coating and applying two coats of weather proof emulsion paint including necessary scaffolding as required at site etc complete all as directed.

Fixing only after repair Steel rolling shutters gear operated type with bevel gear box and crank handle, with out ball bearing, including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as directed .

Material and labour for Ball bearing of suitable size for rolling shutters of gear operated type all as directed

Material and labour for Safety lever locks mild steel with 4 levers suitable for gear operated type rolling shutter all as directed

E/M PORTION

Taking down carefully any type point wiring (light, fans, socket etc) complete including battens and fittings such as switch, ceiling rose, light fittings, regulators, socket, etc and making good disturbed surface of wall/ floor etc complete all as specified and directed.

Material and labour for point wiring (concealed) in walls and on surface of ceiling complete with FRLS PVC insulated unsheathed 1100 volts grade, conforming to IS-694, 1.5 Sq mm (nominal area) multi stranded copper conductor cable down though in and including non metallic medium grade rigid PVC conduit 20mm dia heavy grade, ISI marked, including all accessories, concealed in walls by cutting chases using machine and making good the disturbed surface, with and including suitable modular boxes, switch plates of suitable make and FRLS PVC 1.5 Sq mm copper earth continuity wire connected to earth dolly complete for the following all as specified and as directed. (a) One light point controlled by one, one way switch

Supply and fixing new Decorative LED light 36 watt recessed mounting type of size 600x600mm complete with all accessories & connector etc internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size all as specified and directed Make : CG Cat Part No LCTLRN-36-FO-CDL or equivalent model in Bajaj/Wipro.

Supply and fixing new master LED tube 4ft 20 W LED batten of high-quality materials and design, Extruded aluminum housing enhances safety, High quality PC Diffuser. Reliable and robust housing structure having nominal system lumen output of 2500 lumens and a minimum system efficacy of 125 lm/W. The luminaries should have a colour temperature of 6500K and CRI>83. The luminaries shall meet IP20 rating with THD<10% and PF > 0.95. The total power consumption should not exceed 20W (including driver) complete all as specified and directed. Make : CG Cat part No . CCS-100-20-65-HL2-DP-NWH or equivalent model in Bajaj/Wipro.

Supply and fixing new Surface mounting LED Luminaries 2ft and 10 Watt LED fitting with connecting up with copper 3 core flexible cord of minimum size 1.5 Sqmm complete all as specified and directed Make :CG Cat Part No. LCTL-10-CDL or equivalent model in Bajaj/Wipro.

Supply and fix switch modular type, single pole one way 6 Amps 250 volts AC suitable for 1 module without indicator all as specified and directed. Make : Legrand Cat No. 675501 or equivalent model in Anchor/Havells.

Note : The amount against Schedule of Credit on Page No. 46 shall be deducted from the total amount quoted against Sch 'A' while deriving contract Sum for Acceptance.

M/S Darshan Singh Plaha

chronicle enterprises