Completion of the Balance work Civil and Electro Mechanical at the Emergency Operation Centre EOC IE Ompora Budgam

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :DSR 2022 18.10

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil :

Providing and laying of hand packed stone soling (size 150mm-230mm) before laying of mud mat including ramming and compacting with hand rammers including all carriages.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Backfilling available excavated earth excluding rock including all lifdts and leads complete job including consolidation compaction in 20cm layers watering all complete job

Providing and laying in position specified grade of reinforced cement concrete including curing including all carriages complete. but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing including all carriages complete. but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improveworkability without impairing strength and durability as per direction of Engineer-in-charge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately. ..1 All works upto plinth level including all carriages(Code no 5.38)

All works above plinth level upto floor V level (Code no 5.38.2 )

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

Centering and shuttering including strutting, propping etc. and removal of form for: Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc

Centering and shuttering including strutting, propping etc. and removal of form for: Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form for: Columns, pillars, piers, abutments, posts and struts.

Centering and shuttering including strutting, propping etc. and removal of form for: Stairs (excluding landings) except spiral staircases.

Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platforms.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more(codeno. 5.22A.6 ).

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing bolts including nuts and washers complete.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing including all carriages. Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

15mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement: 6 fine sand) (including cost of all material, leads, lifts and carriages etc upto site of work complete)

12 mm thick cement plaster on ceilings, etc. in (1 cement: 4 fine sand mix). Upto floor V level complete in all respects (including cost of all material, leads, lifts and carriages etc. upto site of work complete).

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shallbe also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacentfinished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing& direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately)Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation inprofile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement window double panels with S.S. friction hinges (300x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension.

Providing and fixing glazing in upvc door, window, ventilator, shutters and partitions etc. complete as per the architectural drawings and the directions of engineerin-charge. With toughen glass transparent in colour of 5.0 mm thickness.

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 10 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.

Providing and fixing 8mm thick high pressure laminated sheets matt finish in upvc doors and partation walls etc complete as per the architectural drawing and the directions of engineer in charge

Filling the gap in between aluminum frame and adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5mm width.

Providing and fixing factory made uPVC white colour partation walls comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. sealant shall be paid separately) Note: dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Dimensions of sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot &double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).(SSR 2020) 22.18

Door handle(stainless steel pipe pull handle bocare(25x127x457 mm) item weight 770 grams

door lockstainless steel(90x140x100 mm)glass to glass lock shape ovel

Door stopper(door mount ,stainless steel)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class deodar wood.(SSR 2020)9.1.3

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately).Second kail wood

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.Second Class kail wood

Providing and fixing hardware fittings of approved brand and of required type as approved by Engineer incharge. complete as per the specifications . (Brass) Modular door lock ss finish handle 10" with duaal locking system inside & outside

Providing and fixing hardware fittings of approved brand and of required type as approved by Engineer incharge. complete as per the specifications . (Brass) bright finished brass handles with screws etc. complete : 150mm

Providing and fixing hardware fittings of approved brand and of required type as approved by Engineer incharge. complete as per the specifications . (Brass) bright finished brass tower bolts (barrel type) with necessary screws etc. complete. :

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Providing and fixing 16 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of tile 600x600 mm(double charge

Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy,

bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing of 75 mm thick dewri stones tiles in flooring with single face fine cheasled only over a bed of cement concrete of grade 1:2:4 of thickness upto 75mm including all carriages complete job.(ramp external)

Wooden planking, tongued and grooved in flooring including fixing with iron screws complete: 25 mm thick Second class teak wood,

Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of: (a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. (b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. (c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyro grip non-combustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product. 300 mm Finished Floor Height (FFH)(SSR 2020)11.67.1

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work

With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

Proving and fixing of washable wall paper for wall Including cost of necessary adhesive specification and design approved by engineer incharge/consultants/client.complete job

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with Armourcrete of M/s The Structural Water Proofing Company Pvt. Ltd. Or Tapecrete of M/s CICO Technologies Ltd. consisting of applying : First layer of slurry of cement @ 0.488 kg/Sqm mixed with Armourcrete or Tapecrete @ 0.253 kg/Sqm. This layer will be allowed to air cure for 4 hours. Second layer of slurry of cement @ 0.242 kg/Sqm mixed with Armourcrete or Tapecrete @ 0.126 kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes supply of waterproofing compound, preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry).(SSR 2020)23.5

French spirit polishing, Two or more coats on new works including a coat of wood filler.(SSR 2020)13.78

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug a

t 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-incharge With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diax40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @ 230 mm interval ,including fixing of gypsum board/calcium silicate board to ceiling section and perimetre channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers’ specification and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimetre channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous and Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.(SSR 2020) 12.62.5

Providing and fixing plannes eaves boarding (300mm x 40mm )( nominal size) second class dewdare wood fixed with screws etc, including all carraiges .All job completed.

Providing and fixing 20mm thick wooden planks ceiling (frame work for base to be paid for separately) with M.S. screws 2nd class kail wood.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : Budloo wood

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gram/m (SSR 2020)12.4.1

Finishing walls with exterior ultima Allura Torino paint of required shade texture rough washability, anti fungal, @ 0.4 kgs / sqm in two coats Including primer coat complete in all respects

Providing and fixing devri stone clading 25 mm thick with exposed face fine dressed with rough backing on wall lining etc. upto 10 meter ht back filled with a grout of 12 mm thick cement sand mortar in 1:3 (fine cheiseled)including pointing in white cement 1:2 with admixture of pigment matching to stone.

Fabrication of modular kitchen with space of electronic chummney all type of modular steel baskets and accessories with provision of plate stand racks spoon basket try , cutlery basket, cup and saucer basket partation basket grain trolly withwith slider tray chennel and finish with granite top . Cbnite fabricate with 25 mm commercial board with over lap modular doors with hydralic auto closed hinges with fixing 8 degree or 0 degree and fixing of key lock and sliding drawers with railing channel size 450 mm in both side of each drawer , drawer lock and steel handle size 100mm inside the cabnit will be laminated sheet 0.8mm thick and outside laminated with texture design 1 mm thick laminate the cabnit will be divide in partation with 25 mm thick wooden board and both sides uper file cabnit, storage cabnit, and lower side cabnit with all locking arragment as per drawing. complete job

Providing and fabrication of wooden modular wadrobe with wall to wall and top to bottom finish with locking mirror and drawers as per drawing total size 1500mm wide x 3000 mm height x600 mm deep with 25 mm thick commercial board with over lap modular doors with hydrolic auto closed hinges with fixing 8 degree or 0 degree and fixed of key lock and sliding drawers with size 600mm x 150mm x 600mm with railing channel size 450mm in both sides for each drawer, drawer locks and steel handle size 100mm inside the cabnit will be laminated with plane laminated sheet 0.8mm thick with and out side laminated with texture design 1 mm thick laminate the cabnit will be divide into partation 25mm wooden board and both sides upper file cabnit, storage,and lower side cabnit with all locking arragment as per drawing complete job

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.DSR 2022 14.16 200 mm dia (OD-200 mm & ID-175 mm nominal)DSR 2022 14.16.5

Proving and fixing of second class deodar wood for wall penelling designed in ornamental pannals shape square / rectangular.(the ornamental pana

ls made up of 12 mm thick of dewdare wood and frame made up of 25 mm thick where 12 mm ornamental panals are fixed Including cost of necessary adhesive ,budloo wood backing and cost of nails etc design approved by Architect/engineer in charge/consultants.complete job.

Manufacturing supplying and fixing retro reflective overhead signage boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type-III of ASTM-D-4956-01 as approved by Engineer-in-charge; letters, borders etc. as per IRC : 67-2001 in silver white with blue colour background and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class -II of ASTM-D-4956- 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminum alloys, rivets or bolts and nuts @ 300mm c/c all along the periphery as well as in two vertical rows along with theft resistant measures including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminum sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawing, specification and direction of Engineer-in-charge (Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment)

Supply and installation signage plates for rooms.meeting halls etc of size 120mm x120mm x1.5mm in ss304 matt finish having letters engrave in the ss plate in black vinyl steam pressed to get a clean finish and having font size of name atleast 30mm fixed on the wall or door surface with high quality adhesive tape of 3M or equivalent complete to thesatisfaction of engineer in charge

Supply and installation signage plates for FIRE EXIT/ LIFT SIGNAGE of size 120mm x120mm x1.5mm in ss304 matt finish having letters engrave in the ss plate in black vinyl steam pressed to get a clean finish and having font size of name atleast 40mm fixed on the wall or door surface with high quality adhesive tape of 3M or equivalent complete to thesatisfaction of engineer in charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry bricks 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.

Providing and fixing G. I. chain link fabric fencing of required width in mesh size 50x50mm including strengthening with 2mm dia wire or nuts, bolts and washers as requiredMade of G. I. wire of dia 4mm, PVC coated to achieve outer dia, not less than 5mm in required colour and shade. complete as per direction of Engineer-in-charge. (SSR 2020)16.25.2

Supplying and stacking at site.Graded crushed stone aggregate of size 53 mm to 22.4 mm

Supply, transportation,Unloading , installation,testing & Commissioning of the following rating of UPS System including unloading,transportation from store to site ,

Supplying and stacking at site.Graded crushed stone aggregate of size - Stone screening of size 11.2 mm nominal size (Type B)

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening /binding material to fill up interstices of coarse aggregate, watering and compacting to the required density.

Painting runway / taxi track/ apron marking with adequate no. of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge including cleaning the surface of all dirt, scales, oil, grease and other foreign material etc. and lining out complete.New work (Two or more coats)New work (Two or more coats)

Providing and fixing cramps of required size and shape in RCC/CC/brick masonry backing with cement mortar 1:2 (1 cement: 2 coarse sand) including curing & drilling necessary hole in stones and embedding the cramp in the whole (fastener to be paid separately).

Providing and fixing expansion hold fasteners on CC / R.C.C./brick masonry surface backing including drilling necessary holes and the cost of bolt etc. complete.Fastener with threaded dia 6mm

Providing and fixing roller supports for gates including cost carriage primer coat etc complete job

Providing and fixing hold fast made of structural steel including cost carriage primer coat complete job

Providing and applying tack coat using hot straight run bitumen of grade – VG-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications. On W.B.M. @ 0.75 Kg/sqm.

Providing and applying tack coat using hot straight run bitumen of grade – VG-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications. On bitumen surface @ 0.50 Kg/sqm.

Providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specifications and directions of Engineer-in-Charge. 50 mm average compacted thickness with bitumen of grade VG-30 @ 3.5% (percentage by weight of total mix) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.

Providing and laying semi- dense Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. Plant of 100-120 TPH capacity.

Providing and laying seal coat of premixed fine aggregate (passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG-10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface including rolling and finishing with road all complete

Filling in paths etc in layers not exceeding 20 cm in depth consolidating each layer by rammng, watering (complete job) GSB filling under in paths.(SSR 2020)16.82.2+ CARRIAGE)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement: 3 coarse sand) including making joints with or without grooves (thickness of the joints except at sharp curve shall not to be more than 5mm) including making drainage opening wherever required complete etc. as per direction of Engineer-incharge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Adjustable TMR (Icu=Ics=100%)(8 Nos) Indicating Lamps ON OFF TRIP( 12 Nos), Capacitor Duty Contactor 25 A (8 Nos), Capacitor Duty Contactor 12.5 A (2 Nos) Capacitor Duty Contactor 5 A (2 Nos), Capacitor 10 KVAR H.D 440 V Gas Filled(2 Nos) Capacitor 25 KVAR H.D 440 V Gas Filled(8 Nos), Capacitor 5 KVAR H.D 440 V Gas Filled(2 Nos) APFCR 12 Stages, Auto Manual Switch(1 Nos) Load Bearing Members to be made out of 2.0 mm CRCA Sheet. Partitions to be made out of 1.6 mm CRCA Sheet, Gland Plates to be 3.0 mm Thick.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong v

ibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge.

Providing Retro-reflective regulatory sign board of size 900mm diameter made out of 2mm thick aluminum sheet, face to be fully covered with high intensity encapsulated lens type retro-reflective sheeting as approved by Engineer-in-charge. Letter, symbols, borders, etc. will be as per IRC:67 with required colour scheme on the boards and with the high intensity grade A. the aluminum sheet to be riveted to M.S. frame of angle iron of size 40x40x4mm. The boards will be fixed to 1 No. 50x50mm square post made of M.S. angle 50x50x4mm, 4m long welded to the frame with adequate anti-theft arrangement. Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminum sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per directions of Engineer-in-charge.

Supply, Installation, Testing and Commissioning of Variable Refrigerant Flow/ Variable Refrigerant Volume modular type air- conditioning system suitable for Heating/Cooling by 100% inverter driven capacity control compressor complete with indoor and outdoor units with individual controller , fittings etc. including full charging of R-410A refrigerant gas complete with operating range down to -20 deg c in heating mode. Make : CARRIER (to ensure compatibility with existing installed indoor units of CARRIER make) AIR COOLED VRF/ VRV OUTDOOR UNITS Supply Instalaltion, testing and commissioning of Modular type outdoor units alongwith base frame/Outdoor stands as recommended by OEM equipped with highly efficient scroll / DC Twin Rotary compressors all with inverter type compressors special heat exchanger, low noise condenser fan, auto check function for connection error, auto address setting and capacity as mentioned below.

Extra carriage of excavated material beyond 50m as per SOR 2022 carriage sheet (lead 150m)

Providing and making Gabion structure with mechanically woven double twisted hexagonal shaped wire mesh Gabion boxes as per IS 16014:2012, MORTH clause 2500, of required size, Mesh type 10x12 (D=100mm with tolerance of ± 2%), zinic +10% ,Al alloy + PVC coated, mesh wire diameter 2.7/3.7 mm ( ID/OD), mechanically edged/selvedged with partitions at every 1 m interval and shall have minimum 10Nos. of openings per meter of mesh perpendicular to twist, tying with lacing wire of diameter 2.2/3.2mm (ID/OD), supplied @3% by weight Gabion boxes filled with boulders with least dimension of 200mm, as per drawing, all complete as per directions of engineer-in-charge.

Providing and fixing thermal insulation of ceiling (under deck insulation) with specified glass wool conforming to IS: 8183, 50mm thick, wrapped in 200 G Virgin Polythene bags fixed to ceiling with metallic cleats (50x50x3mm) @ 60cm c/c and wire mesh of 12.5mm x 24g wire for top most ceiling of building. 12.50.1 With resin bonded fiber glass wool with density 24 kg/cum(SSR 2022 12.50.2)

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Electric resistance or induction butt welded tubes SOR 2022 (10.16.3)

Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.50 mm thick with zinc coating not less than 275 gram/m2 SOR 2022(12.1.6)

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. 110 mm diametre

Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

Plumbing & Sanitary Works for Guard Hut

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets,40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing Under Counter wash basin,with 32 mm Waste Coupling and other allied accessories including cutting and making good the walls wherever required:- White Vitreous China Under Counter Wash basin.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required : 510x1040 mm bowl depth 225 mm

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

Providing and fixing toilet paper holder with Flap made out of C.P Brass

Constructing septic tank, of size 5.0 mx 2.5 mx1.55 m approx. height(Height to be fixed as per site requirement i.e. below invert level of last manhole , in B/W, 350/230 mm thick ( minimum) walls .

Providing and fixing C.P Brass Soap Dish.

Providing and fixing on wall 35 LTRS Electric Geyser with ABS Body.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing CP brass towel rail complete with CP brackets fixed to wooden cleats with CP brass screws .

Providing and fixing CP Short Body Bibcock with Valve Flange

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing. 110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

75 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Providing and Fixing of Floor Traps 110 mm with double chrome plated Cover one Grated and one closed and all other fittings required.Makes:- Astral/SFMC/Finolex

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge. Concealed work, including cutting chases and making good the walls e

Providing and Fixing of Floor Traps 110 mm with double chrome plated Cover one Grated and one closed and all other fittings required.Makes:- Astral/SFMC/Finolex

1620 (20 mm OD) pipe

2025 (25 mm OD) pipe

SITC of ABC Type Fire Extinguisher (5 Kg capacity) N.S

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge.

Internal work (Exposed on wall) 2025 (25 mm OD) pipe

External work 4050(60 mm OD ) pipe

Providing and fixing unplasticised PVC connection pipe with brass unions: 45 cm length, 15 mm nominal bore

Cutting holes upto 30x30 cm in walls including making good the same with common burnt clay F.P.S.(non modular) bricks

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of P.V.C pipes including bed concrete as per standard design : 110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Supply, Installation of PVC Gully Trap of Size 110 mm

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 16 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.

50 mm Diameter

Supply,Installation,Testing and Commissioning 320 Cu.m/Hr. AC 220-240 Volts, 50 Hz exhaust fan made out of ABS Plastic Material with inbuilt thermo cutoff Protection and Noise Level not exceeding 37 dB of Following Sizes including connection etc. complete as required . 300 mm

Supply installation testing and commissioning of IP20 led downlighter 15 W-18 W +/- 1 W LED Surface downlighter round shape with minimum system lumen efficacy of 100 lm/W with Pressure Die cast Aluminium Heat Sink and P.F.>0.95 ,THD<10% ,CCT 5700K, CRI 80.The LED with Useful life of 50000 Hrs at L70.. The Input voltage range shall be 150V to 270V .The Fixture should have In-built Surge Protection of 2kV. Certification:- LM79 & LM80 test report should be from govt approved Inhouse NABL lab/ government of India authorised lab .

Metre

Per Liter

Providing and fixing 15cm wide 45 cm overall semi circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc. including making necessary connections with rain water pipes complete.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore

Supplying and Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in groundin Existing DWC Pipe including excavation, sand cushioning, protective covering and refilling the trench etc as required. 4.0 C X 16 Sq.mm A2XFY

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. 15 mm nominal dia

Point

Supply and Making end Termination with Brass Compression Gland and Aluminium Lugs for the Following Sizes of PVC insulated and PVC Sheathed/XLPE Aluminium Conductor Cable of 1.1 KV Grade as Required (Complete) 4 X 16 sq. mm (28mm)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Electric Works for Guard Hut

Supplying and fixing suitable size GI box with modular plate and cover in front on urface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Wiring for Circuit/Submain Wiring along with earth Wire with the following Sizes of FRLSPVC insulated copper conductor,single core Cable in surface/Recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and Fixing suitable size G.I box with modular plate and cover in front on surface or in recess,including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch,connection,painting etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earthbar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 way , Double door

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supply installation testing and commissioning of IP:20 Aluminium Batten 20W-22 W +- 1 W LED Surface Mounted 4 ft. with system lumen efficacy of 100 lm/W and P.F >0.9 THD <20% CCT 6500K,CRI 80 .The LED should have life of 50000 Burning Hours at L70.The input voltage shall be 150 V to 270 V.The fixture should have inbuit surge protection of 2KV.Certification-LM 79 and LM 80.The test report should be from Govt. Approved Lab/inhouse NABL Lab.

Single headed GunmetalDSR 2022 18.10.1

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or e

lectronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in Existing surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. DSR 2022 1.10.3

complete pending balance work as per site conditions for light point/ fan point/ exhaust fan point/ call bell point for Installation of modular switch, modular plate, suitable GI box etc. as required. N.S

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.DSR 2022 1.55.3

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. DSR 20221.21

20mmDSR 20221.21.1

32mmDSR 20221.21.3

40mmDSR 20221.21.4

Wiring for Light /Power Plug with 2 x 4 sq.mm FRLS PVC Insulated Copper Conductor single core cable in Existing surface/Recessed medium class PVC Conduit along with 1 No. 4 sq.mm FRLS PVC Insulated copper conductor single core cable for loop earthing as required.DSR 20221.12

Complete Pending Balance work for Wiring for Circuit/Submain Wiring along with earth Wire with the following Sizes of FRLSPVC insulated copper conductor,single core Cable in Existing surface/Recessed medium class PVC conduit as required.DSR 20221.14

2 X 2.5 SQ.MM + 1 X 2.5 SQ.MM EARTH WIREDSR 20221.14.2

4 X 4 sq. mm + 2 X 4 sq. mm earth wireDSR 20221.14.8

4 X 6 sq. mm + 2 X 6 sq. mm earth wireDSR 20221.14.9

4 X 16 sq. mm + 2 X 6 sq. mm earth wireDSR 20221.14.11

4 X 25 sq. mm + 2 X 16 sq. mm earth wireN.S

4 X 50 sq. mm + 2 X 25 sq. mm earth wireN.S

Supplying and fixing modular blanking plate on the existing modular plate and switch box excluding modular plate as requiredDSR 20221.26

Supplying and fixing two Module Stepped Type Electronic Fan Regulator on the existing Modular Plate Switch Box including Connections but Excluding Modular Plate etc. as RequiredDSR 20221.25

Supplying and Fixing suitable size G.I box with modular plate and cover in front on surface or in recess,including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch,connection,painting etc. as required.DSR 20221.32

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.DSR 20221.31

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)DSR 20222.4

4 way (4 + 12), Double doorDSR 20222.4.1

6 way (4 + 18), Double doorDSR 20222.4.2

12 way (4 + 36), Double doorN.S

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.DSR 20222.13

40 AmpsDSR 20222.13.1

63 AmpsDSR 20222.13.2

25 AmpsN.S

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)DSR 20222.3

12 way , Double doorDSR 20222.3.3

6 way , Double doorDSR 20222.3.1

Supplying and fixing following way VTPN D.B Conforming to IS:8623-1 and 3,IEC 61439-1 and 3 ,IK-08 Compliant,IP43 fabricated out of CRCA sheet SteelN.S

12 Way Incomer MCCB and Out going 12+12+12

Supplying and fixing 5 amps. to 32 amps.rating 240 volts 'C' series, miniature circuit breaker of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.DSR 20222.1

Single PoleDSR 20222.10.1

Double PoleDSR 20222.10.3

Triple pole and neutralDSR 20222.10.5

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.DSR 20222.2

100 A,36KA,FPMCCBDSR 20222.2.13

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.DSR 20222.11

ENVIRONMENTALLY SAFE MAINTENANCE FREE EARTHING SYSTEM

Supply, installation, testing and commissioning of Advanced Maintenance Free environment friendly Earthing system consisting of 1 no. of 3mtr length, 17.2 mm dia UL certified earth electrode made of high tensile low carbon steel circular rods, molecularly bonded copper on outer surface (minimum copper bonding thickness-250 microns) with GI terminals to connect incoming strips, (Environment friendly backfill compound duly certified as per ANSI/NSF standard 60/Toxic content certificate as safe for use near potable ground water resources strictly as per specification enclosed. The job includes Earth pit chamber (300mm x 300mm) with CI cover for the above. Necessary soil treatment is to be made by the contractor in order to improve the Pit resistance value.

Providing and Fixing 25 mm x 5 mm Copper Strip in 40 mm dia. G.I Pipe FRL Earth Electrode including connection with Brass nut ,bolt,spring,washer,excavation and refilling etc. as required.DSR 20225.10

SITC of Ceiling Fan,Capacitor type suitable for low voltage operation including wiring the down rods of standard length(Upto 30 cm)with 1.5 sq.mm FR PVC insulated,copper conductor,single core cable including providing and fixing phenolic laminated sheet cover on the Fan Box etc as Required.N.S 1200 MM SWEEP(5 STAR)

SITC of pre-wired Recess/Surface Mounted 2Ft X 2 Ft LED Panel Fitting with ,Driver Etc. including connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required. (.JAQUAR /WIPRO/PHILIPS or equivalent)125 LUMEN/WATTN.S

SITC of pre-wired Recess /Surface Mounted LED Ceiling Light 12 W including connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required.(.JAQUAR /WIPRO/PHILIPS or equivalent)N.S

SITC of pre-wired Recess /Surface Mounted LED Ceiling Light High Bay 150 W including connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required(.JAQUAR /WIPRO/PHILIPS or equivalent)N.S

SITC of pre-wired Recess Mounted LED Ceiling Light 18 W including connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required(.JAQUAR /WIPRO/PHILIPS or equivalent)N.S

SITC of pre-wired Surface Mounted LED Tubelight Light 1 x 22 W includ

ing connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required(.JAQUAR /WIPRO/PHILIPS or equivalent)N.S

Supply of AC 230/250 Volts, 50 Hz exhaust fan with louveres of Following Sizes including connection etc. complete as required .N.S

Supply, installation, testing & commissioning of inverter for dormitory building 3.5 kVA pure sine wave inverter, with inbuilt display and protections with double battery 12V, 260AH

Supply, installation, testing & commissioning of 2 x 3.5 kVA pure sine wave inverter, with inbuilt display and protections with 3 x double battery 12V, 260AH for ware

Supplying and Laying of 1 No XLPE insulated and PVC Sheathed /XLPE Power Cable of 1.1 KV Grade of Following Sizes in the existing RCC/Hume/DWC/Stone ware/Metal Pipe/Cable Tray as Required.N.S

3.5 C x 300 mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.N.S

3.5C x 185 mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.N.S

3.5 C x 50mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.N.S

3.5 C x 25mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.N.S

4.0 C x 16mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.N.S

Supply, Installation testing and commissioning of 3 C x 120mm² 11 KV XLPE insulated Aluminum. conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with Earth HT Cable).(Raychem make)N.S

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.DSR 20229.1

3.5 C x 300 mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.DSR 2022 9.1.30

3.5C x 185 mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.DSR 2022 9.1.27

3.5 C x 50mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.DSR 2022 9.1.22

3.5 C x 25mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.DSR 2022 9.1.20

4.0 C x 16mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.9.1.33

Supply, Installation testing and commissioning of Outdoor/Indoor Termintion Kit for 3 C x 120mm² 11 KV XLPE insulated Aluminum. conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with Earth HT Cable).(Raychem make)N.S

30KVA/30KW True Online Modular UPS with 30 KW Power Cabinet with 6 no. of 5 KW power Modules with 240VDC along with external SMF Battery Bank of minimum VAH of 28800VAH with 2 year onsite Warranty. Battery Make: - Exide Power Safe/ Quanta Make Batteries, With MS battery rack, BCB, Links & 1 x DC cable 5mtrs. N.S

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

300 mm width X 50 mm depth X 1.6 mm thicknessDSR 2022 4.6.4

450 mm width X 50 mm depth X 2.0 mm thicknessDSR 2022 4.6.6

600 mm width X 50 mm depth X 2.0 mm thicknessDSR 2022 4.6.7

Supply, transport, unloading, shifting & Fabrication of steel sections and erection of MS base frames, MS angle channels, flat etc for supporting various items of equipment such as various panels/switchgear,dummey panels, adaptor boxes addition support for proper cable termination, MS Fabricated cable trays, push button stations, junction boxes, light fittings, DB etc. The scope include welding, bolting, chipping , grouting etc, including applying one antirust coat of approved primer and two finished coats of approved paint with primer & paint, breaking and finishing of walls, floors etc. Contractor has to apply one coat of antirust paint (Red-oxcide ) with in one day after structural steel received. The scope is inclusive of minor civil work as required, supply of GI hardware materials, consumables, tools & tackles and necessary labour with supervision but not limited to, and complete as per approved drawings, specification and directions of Engineer-In charge.N.S

FIRE DETECTION WORKS

Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.DSR 2022 17.2.3

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.DSR 202217.2.4

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete asrequired. DSR 202217.2.6

Supplying, installation, testing & commissioning of fault isolator complete with base as required.DSR 202217.2.7

Supplying, installation, testing & commissioning of addressable manual call point complete as required.DSR 202217.2.14

Supply and drawing of 2 C X 1.5 Sq mm Un armoured cable in Existing Conduit.N.S

Supplying and Fixing of Following sizes of PVC Conduit along with Accessories in surface/Recess including painting in case of surface conduit,cutting the wall and making good the same in case of recessed conduit as required.

25mm PVC ConduitDSR 20221.21.2

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.DSR 202217.3.1

installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.DSR 202217.3.2

speaker cable Two pair, 2-core, 1.5 sqmmDSR 202217.5.3.2

Supply, installation, testing and commissioning of 120 liters Seamless Cylinder ( Or as per Calculation) with valve capable of withstanding pressure of 42 bar at 50 dec c Calculation, Cylinder / PESO / CCOE Approved.N.S

Supply, installation, testing and commissioning of 34 liters Seamless Cylinder ( Or as per Calculation) with valve capable of withstanding pressure of 42 bar at 50 dec c Calculation, Cylinder / PESO / CCOE Approved.N.S

Supply, installation, testing and commissioning of Pressure Gauge +Low pressure supervisory switch. Make (Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of SINORIX 1230 / FM200 VDS approved system. Gas calculation software should be VDS or UL Listed. Make (Kidde/Hochiki/Siemens/Feuerx)N.S

Supply, installation, testing and commissioning of Electromagnetic Actuator. The actuator should be capable of withstanding pressure at least of 90 bar. UL/VDS listed.Make (Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Manual Actuator. The actuator should be capable of withstanding pressure at least of 100 bar at 50 deg c. UL/VDS listed.Make (Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Pneumatic actuator. The actuator should be capable of withstanding pressure at least of 100 bar at 50 deg c UL/ VDS listed. Make(Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Flexible Discharge Hose with minimum bending radius of 125mm and brusting pressure should be more or equal to 180 bar. UL/VDS listed. Make idde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Flexible Actuation Hose with minimum bending radius of 75mm and brusting pressure should be more or equal to 660 bar. UL/VDS listed. Make (Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Discharge Nozzle. The nozzle should be capable of handling at least 176 bar at 50deg c .Ul/ VDS Listed. Make (Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Check Valve UL/VDS listed. Make Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Manifold complete for making header of gas cylinders.N.S

Supply, installation, testing and commissioning of Wall mount kitN.S

Supply, installation, testing and commissioning of 2 Zone Gas Release panel with release module and battery backup. Make (Kidde/Hochiki/Siemens/Feuerx/ Ravel).N.S

Supply, installation, testing and commissioning of Abort Switch. Make (Kidde/Hochiki/Siemens/Feuerx/ Ravel).N.S

Supply, installation, testing and commissioning of M.S. Seamless pipes as per ASTM A 106 Gr. B, schedule 40 with necessary fittings. Make jindal, MSS, TATAN.S

VESDA server grade detectors Make Xtralis, SiemensN.S

Installation, Tetsing & Commisioning of 12V 2 Amp Power Supply Unit with battery back up for above Detector. Make Xtralis, SiemensN.S

End CapN.S

T Joints & L Bends for sampling point networkN.S

Sampling Pipe Smooth bore PVC Pipe 21mm ID and 25mm ODN.S

Sampling point labelsN.S

Flash HooterN.S

2 core 1.5 sqmm FRLS armored cableN.S

TELEPHONE AND NETWORKING WORKS

Providing, fixing supplying, termination & certification of INTERNET networking . The item mentioned shall include the cost for laying Cat 6 UTP wire of in existing conduits for the wiring & it shall be such that each point has a dedicated single CAT 6 wire from the wall outlet to the patch panel.The rates quoted shall include the cost of termination of CAT6 cable in the wall sockets & patch panel including the cost of certification by network engineer using a penta-scanner , ferrulling of every point on both sides the contractor will have to provide the network certification in writing. Nothing extra shall be paid for on account of termination, crimping, certification etc. complete in all respects as desired by Engineer Incharge. The following items will be got exectued as under.

Supplying,Installation,Testing and Commissioning of I/O Modules Complete with Box,RJ-45 Socket,Front Plate as per the Satisfaction of the Engineer InchargeN.S

Supplying,Installation,Testing and Commissioning of I/O Modules Complete with Box,RJ-11 Socket,Front Plate as per the Satisfaction of the Engineer Incharge.N.S

Supplying and Fixing of Following sizes of PVC Conduit along with Accessories in surface/Recess including painting in case of surface conduit,cutting the wall and making good the same in case of recessed conduit as required. 25mm PVC Conduit

Supplying and Drawing of UTP4 pair CAT-6 LAN cable in the existing surface/Recessed Steel/PVC Conduit as required .N.S

Supplying and drawing 2 pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/PVC conduit as required.N.S

Supply, Installation, Testing and Commissioning of Semi managed 24 port POE , complete as per specification and as desired by EIC, N.S

Supply & Erection of lockable 9/12 U rack with 5A strip and two fan for distribution, mounting of patch panels, hubs, switches etc,, complete as per specification and as desired by EIC,Make : N.S

200 mm diaDSR 2022 18.11.7

commissioning of 10 Pair jelly filled armoured cable of 0.5mm of each Pair Telephone Cable in the existing surface/ recessed steel/ PVC conduit, complete in all respect as per specification and desired by EIC N.S

Supplying,Installation,Testing and Commissioning of 40 Inches Full H.D LED Display Monitor as per the Specifications attached.N.S

Supplying of 16 Channel Network Video Recoder(NVR) as per the Specifications Enclosed with a Hard Disk Memory of 8 TB Capacity(SONY/HONEYWELL/BOSCH)N.S

Supplying,Installation,Testing and Commissioning of 2 Mega Pixel Full High Definition Weather Proof Bullet Camera.N.S

Supplying,Installation,Testing and Commissioning of 2 Mega Pixel Full High Definition Dome camera.N.S

18 HP of any combination with high efficiency

10 HP of any combination with high efficiency

Indoor Units:Round Flow Cassette Type Testing and commissioning of Cassette Type Indoor units equipped withl, pre-filter, fan section with suitable static fan, multispeed motor, coil section with DX coil, outer cabinet, drain pan, drain pump, insulation, pipe connections, variable evaporative temperature control etc. of various capacities as per specifications and drawings, All indoor Units should have force shut option to connect with fire alarm or key card adaptor, so that the unit automatically stops in case of fire or key card removal.N.S Carrier Make

Cassette Type Indoor Unit - 1.6 HP

Cassette Type Indoor Unit - 2.5 HP

Cassette Type Indoor Unit - 3.2 HP

Heat Reclaim Ventilation Units (HRV) Supply, Installation, testing and commissioning of Heat Reclaim Ventilation (HRV) with airflow rate 950 CMH and external static pressure 135 pascal for the fresh air circulation.N.S Heat Reclaim Ventilator - 950 CMH, HeatingCapacity 10.92 KW

Supply and installation of Refrigerant Piping Y-Joints as required to connect the above outdoor units and indoor units. ( liquid and gas line as one set)N.S

Supply and installation of Refrigerant Piping HEADER -Joints required to connect the above outdoor units and indoor units. ( liquid and gas line as one set)N.S

Supply, Installation, testing and commissioning of Corded remote

Supply, Installation, testing and commissioning of Centralised Remote Controller which can control maximum 64 groups of indoor units, malfunction code display in the screen, .N.S

SITC of PVC (Minimum 15 Kg/Sqcm pressure rated) Drain Water Piping complete with fittings (elbows, tees, reducers, sockets etc.), supports, jointing and any other item required to make the system complete. Nominal Diameters of Pipes in mm as indicated below:N.S

25 mm ( with 9 mm Class- O XLPE)

32 mm ( with 9 mm Class- O XLPE)

40 mm ( with 9 mm Class- O XLPE)

50 mm ( with 9 mm Class- O XLPE)

SITC of Copper Refrigerant piping for VRV / VRF System complete with fittings, supports, jointing, insulation with class O -XLPE , gas charging & commissioning as per specifications, all accessories as per specifications and any other item required to make the system complete. Nominal Dia in mm OD as indicated below : N.S

34.9 ( with 19 mm insulation )

28.6 ( with 19 mm insulation )

25.4 (with 19 mm insulation)

22.2 ( with 19 mm insulation )

19.1 ( with 13 mm insulation )

15.9 (with 13 mm insulation)

12.7 ( with 13 mm insulation )

9.5 ( with 13 mm insulation )

6.4 (with 13 mm insulation)

Providing & fixing control cum transmission wiring of 2 core x 1.5 sqmm copper in suitable conduits between indoor units and outdoor units and indoor units and remote controllers.N.S

Supply, installation, balancing and commissioning of fabricated at site GSS Sheet Metal Rectangular/Round Ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as requiredN.S

Thickness 0.63 mm sheet

Thickness 0.86 mm sheet

Supply & installation of Acoustic Insulation complete with XLPE / Rubber as per approved drawings and specifications of following sheet thickness complete as requiredN.S Thickness 25 mm

Flexible Duct with Spigot 100 mm Dia.N.S

Flexible Duct with Spigot 75 mm Dia.N.S

Disc Valves 100 mm Dia.N.S

Disc Valves 75 mm Dia.N.S

FIRE FIGHTING WORKS

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :DSR 2022 18.7

25 mm diaDSR 2022 18.7.1

40 mm diaDSR 2022 18.7.3

50 mm diaDSR 2022 18.7.4

65 mm diaDSR 2022 18.7.5

80 mm diaDSR 2022 18.7.6

100 mm diaDSR 2022 18.7.7

150 mm diaDSR 2022 18.7.8

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :DSR 20229 Single headed GunmetalDSR 2022 18.9.1

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :DSR 2022 18.10 Single headed GunmetalDSR 2022 18.10.1

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :DSR 2022 18.11

150 mm diaDSR 2022 18.11.6

80 mm diaDSR 2022 18.11.4

100 mm diaDSR 2022 18.11.5

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.DSR 2022 18.13

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :DSR 2022 18.16 Gun MetalDSR 2022 18.16.1

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.DSR 2022 18.17 30m DSR 2022 18.17.1

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :DSR 2022 18.19 2 way-100 mm dia M.S. PipeDSR 2022 18.19.1

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.DSR 2022 18.20

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :DSR 2022 18.21

Upright SprinklerDSR 20222 18.21.2

Pendent SprinklerDSR 2022 18.21.1

Horizontal side wall sprinklerDSR 2022 18.21.3

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.DSR 2022 18.22

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.DSR 2022 18.23 100 mm dia.DSR 2022 18.23.1

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hy

draulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :DSR 2022 18.24 100mm diaDSR 2022 18.24.2

Testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :DSR 2022 18.21 Pendent SprinklerDSR 2022 18.21.1

Installation, testing and commissioning of electric driven terrace pump (available at site) suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for peration on 415 volts, 3 phase, 50 Hz, ACsupply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation,conforming to IS-325.(c) M.S.fabricated common base plate, coupling, coupling guard, founation bolts etc.as required.(d) Suitable cement concrete foundation duly plastered and with anti vibration pads.DSR 202 18.24 450 lpm at 35 m HeadDSR 2022 18.4.2

Providing, installation, testing and commissioning of stainless steel Y-strainer 65 mm fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.DSR 2022 18.15.3

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :DSR 2022 18.8 Gun metalDSR 2022 18.18.1

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.DSR 2022

3.5 C x 50mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.DSR 2022 9.1.22

4.0 C x 16mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.9.1.33

1000mmDSR 2022 18.25.2

Providing and fixing Weather proof hose cabinets for yard hydrant fabricated from 16 g MS sheet with full glass door and locking arrangement, suitable to accommodate one hydrant valve, 2 nos.15m long hose, 1 No branch pipe and one fireman's axe. The cabinet shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required. (Approx 0.75mx0.6 mx 0.25 m).N.S

Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete.N.S

Providing and fixing fully glazed MS fully welded construction double leaf door shutter for fire hydrant station fabricated from MS 50x50x6 mm angle iron frame, fixed to wall and hinged MS 40x40x5 mm angle iron door shutter with required MS sash bars for glazing complete with locking arrangements, stove enamelled fire red finish with 'FIRE HYDRANT' written in front.N.S

BALANCE WORKS FOR ELEVATOR

Testing and commisioning of 13 Passenger Lift with the following Specifications CAPACITY (kgs) :884 Kg, 13 persons SPEED (mps): 1.5 mps RISE (m ) :8 m(Appx) STOPS: 2 Stops With (all opening on the same side) DRIVE :VF Regenerative (Closed Loop) MACHINE :PM Gearless (Located in shaft on top of guide rails) "CAR FINISH• : Rear Mid Panel = SS HAIRLINE Rear Corner Panels = SS HAIRLINE Side Mid Panels = SS HAIRLINE Side Corner Panels = SS HAIRLINE Front Panels = SS HAIRLINE type " FALSE CEILING FINISH: SS HAIRLINE HAND RAILS :Stainless Steel Mirror Finish Handrails on rear car panels VENTILLATION:Cross flow fan FLOORING:Vinyl Tiles DOOR OPERATOR:DC Door Operator "STANDARD FEATURES:Anti-nuisance Car Call Protection Independent Service (for Duplex only) Overload Device Nudging Emergency Firemen’s Service Emergency Car Light Unit Infrared Curtain Door Protection Door Time Protection Emergency Alarm Button Extra Door Time of Lobby & Parking Door Open/Close Button Manual Rescue Operation Belt Inspection DriveAuto Fan Cut Off (TYKAN MAKE)"

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.DSR 2022 4.6

50mm (W) x 50 mm (H) x 1.6mm wide cable tray perforated typeN.S

900 mm width X 62.5 mm depth X 2.0 mm thicknessDSR 2022 4.6.13

AUDIO VIDEO CONFERENCING

Supply installation testing & commissioning The System 2-Way wall mount Speaker System with 6 inch lf & 1 inch hf compressor driver unit only with 100 watt rms power continious and max spl of minimum 121 db ; with paint finish .N.S

Supply installation testing & commissioning of class h or d power amplifier with 2 x 450 watt rms power at 4 ohms per channel for speakers .N.S

Control Unit:- Powers up to 50 discussion units, Cascade capability to handle up to 300 discussion units, Conference mode: Free talk, request to talk and full remote,2 Mic/Line In + 1 Aux In + 2 Return In, Built-in feedback suppressor and digital audio processing (DSP), Gain sharing algorithm substantially reduces the risk of feedback while maintaining a natural sound. N.S

Delegate Units:- Crystal-clear, 24-bit digital audio processing with 12-band feedback suppressor, Easy plug-and-play operation,discussion units, integration units, and interpretation units (max of six INTs) can be connected

, in either daisy chain or ring topology, to each control unit with long gooseneck microphone 320 MM Length. N.S

Chairman Unit:- Crystal-clear, 24-bit digital audio processing with 12-band feedback suppressor, Easy plug-and-play operation, A total of 100 ATUC-50DU discussion units, ATUC-50IU integration units, and ATUC-50INT interpretation units (max of six INTs) can be connected, in either daisy chain or ring topology, to each ATUC-50CU control unit With long gooseneck Microphone 430MM Length.N.S

Supply Installation testing & Commissioning of Gooseneck cardioid Microphone with minimum gooseneck length of 16.46 INCH MM, polar pattern Cardioid, Frequency Range 70-16000 Hz, Sensitivity18mV/Pa, Impedance >2000 ohms ; with on/off base along .N.S

Supply installation testing & commissioning of Cordless Handheld Microphone with UHF frequency .N.S

SITC of Multipoint video conferencing system with 3 + 1 Location library Supports with Full HD resoliution , Supports multiple HD pan-tilt-zoom cameras .N.S

SITC of Professional display panels with 60 inch size with full Hd resolution of 1920 x 1080 ; with view angle of 178 degree x 178 degree .N.S

SITC of Professional display panels with 86 inch size ; with 4 k resolution with view angle of 178 degree x 178 degree.N.S

Wireless presentation system with 2 dongle along processor for wireless presentation in conference room Display Port, Single link DVI-I , VGA (via included convertor, highest resolutions only with reduced blanking) ,In "Dual screen" mode, connection can occur either through DVI and Display Port, or through VGA and Display Port..N.S

Mini Size Extender set consists of a Transmitter and a receiver. Hdbase T technology is used to transmit high - resolution 1080p/4k signal to the receiver up to 70/40m via a cat5e/cat6A cable . N.S

Supplying, filling, spreading and leveling stone boulders of size range 5 cm to 20 cm, in recharge pit in the required thickness for all leads and lifts all complete as per direction of Engineer-in-charge.

Providing Retro-reflective regulatory sign board of size 900mm diameter made out of 2mm thick aluminum sheet, face to be fully covered with high intensity encapsulated lens type retro-reflective sheeting as approved by Engineer-in-charge. Letter, symbols, borders, etc. will be as per IRC:67 with required colour scheme on the boards and with the high intensity grade A. the aluminum sheet to be riveted to M.S. frame of angle iron of size 40x40x4mm. The boards will be fixed to 1 No. 50x50mm square post made of M.S. angle 50x50x4mm, 4m long welded to the frame with adequate anti-theft arrangement. Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminum sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per directions of Engineer-in-charge.

Supply Installation testing & Commissioning of main SYSTEM RACK - M.S. Rack with Power indicator, power sockets and isolator fitted duly prewired to accommodate Control Room equipments for in house equipments with cooling fn at back gate e.g. Amplifiers, Controller, Equalizer etc as required.N.S

Supply Installation testing & Commissioning of PATCH CORDS ( for SYSTEM INTERCONNECT ) - High grade professional low-noise bable, 2-Core High conductivity PVC insulated in PVC jacket,shielded Copper Cable with di-electric insulator to prevent RF interference with necessary XLR male/female connectors EP Jacks / RCA Jacks etc as required.N.S

Supply, laying & Fixing of Microphone Lines High grade, profeional, Low-noise, 2-Core High conductivity PVC insulated in PVC Jacket, Shielded, Copper Cable with di-electric insulator both end with XLR m/f connector as required .N.S

Supply, laying & Fixing of Speaker Lines: 2-Core, High definition Speaker Cable, PVC insulated in PVC jacket laid in existing conduits as required.N.S

Cable Cubby /Patch Panel, surface access enclosue, openable with press down on the top the enclosure with one data input on HD 15 connector , one video input on RCA connector , two cat 6 RJ 45 connector for LAN .N.S

Supply laying & fixing of Cat 6 Shielded cables for the Video wall and pannel .N.S

Supply & laying of HDMI cable with 20 meter length .N.S

Supply & laying of HDMI cable with 1.5 meter length .N.S

Per Mtr.

EXTERNAL ELECTRIC WORKS

Supplying and Installing Following Size of Perforated G.I Cable Tray with Perforation not more than 17.5% in convenient Sections, joined with connectors ,suspended from the Ceiling including bolts and Nuts ,etc as required. 900 mm (W) x 50 mm (H) wide cable tray Ladder Type

Design, manufacture, supply, loading & unloading, erection, testing and commissioning of 415V, 320 KVA DG Set with alternator complete with acoustic enclosure, all fittings and accessories as required/ as specified in the technical specification Make: Sudhir, Kirloskar or Equivalent. .N.S D.G SET 320 KVA ) >> Radiator Residential type silencer >> Anti-vibration mounts Battery and charger Dynamo Engine instrumentation Panel Other accessories as Required

Supply, laying, testing & commissioning of 1.1 kV grade, armoured, PVC insulated multi core Cu conductor LT control Cable including necessary cleats, clamps end connection with gland & termination etc. for DG set

4C x2.5 sq.mm (YWY)

3C x 2.5 sq.mm (YWY)

4C x4sq.mm (YWY)

12 C x 2.5 sq.mm

Supply and connect fuel pipe of M.S medium class pipe with flange between 990 ltrs. Fuel tank and engine. Of suitable dia

Supply, receive at site, store, unpack, assemble and connect Exhaust pipe with Class-B MS pipe with flanges. Vendor has to confirm Pipe sizes.

8" for horizontal pipe

14" for vertical pipe

8" cladding

14" cladding

Silencer cladding

Supply & Fabrication with steel sections and erection of MS base frames , MS angle channels , flat etc for supporting various items of equipment Panel , Bus ducts , adaptor boxes addition support for proper cable termination, cable trays, etc. Including welding, bolting, chipping , grouting etc, including applying one antirust coat of approved primer and two finished coats of approved paint , breaking and finishing of walls, floors etc. The scope is inclusive of minor civil work as required, supply & installation of GI hardware materials, consumables, anchor fasteners, tools & tackles and necessary labour with supervision but not limited to, and complete as per approved drawings, specification and directions of Engineer-In-Charge. Scope also includes contractor's own lifting and transporting arrangement.

izer in case of any fault "

Supply,Installation of 3 Mtr 80 mm G.I Pole with Foundation in conceret mix of 1:2:4 along with muffler upto a height of 450mm and PVC Junction Box having the faility to house 4 way Bekellite strip and 6 A MCBN.S

SITC of Integral Pole Mounted Decorative LED Post Top with Spherical Shade polycarbonate Diffuser and IP:65 Protection Model No. Wipro(LP-07-431-xxx-57-CL) 35 WattsN.S

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.N.S

Supplying and Laying of 1 No. DWC High Density Poly ethylene Pipe having Corrugation on Outer wall and Plain surface inner wall Conforming to IS: 14930 Part-1 and 2 Complete with accessories for Protection of 1.1 KV Grade under Ground cable Directly in Ground at a Depth of 50 CM including excavation and Refelling the Trench Etc.as Required .N.S

Size 63/50mm

Supplying,Installation and Testing of 50 mm Cu. Pipe Filled with Crystalline conductive Mixture with Copper Strip of Size 32 mm x 5 mm of Length 2 mtr with Ecofriendly Backfill Compound 50 Kg.Makes:- nus/Ashlok/GMAXX

Flexible Duct with Spigot 75 mm Dia.N.S

Disc Valves 75 mm Dia.N.S

Providing and Fixing 50 mm x 6 mm Copper Strip in 80 mm dia. G.I Pipe FRL Earth Electrode including connection with Brass nut ,bolt,spring,washer,excavation and refilling etc. as required.

Supplying, Installation and Testing of 50 mm G.I. Pipe Filled with Crystalline conductive Mixture with G.I Strip of Size 40 mm x 6 mm of Length 2 mtr with Ecofriendly Backfill Compound 50 KgMakes:- Genus/Ashlok/GMAXX

Providing and Fixing 75 mm x 10 mm G.I Strip in Earth Electrode including connection with G.I nut ,bolt,spring,washer,excavation and refilling etc. as required.

25 mm diaDSR 2022 18.7.1

50 mm diaDSR 2022 18.7.4

Supply, fixing, tetsting and commissioning of early steamer Emission type lightening protection compelete with capturing head, adapter to fix, testedas per NFC 17-102 for anitcipating emission time 30 Micro Seconds to be installed at top of the building with the protection radius of 60 Mtr (Level 2 Protectionas. The job includes SITC of Master (AI/GI of suitable Height) for mounting the terminal and adaptor to mount the lightining rod with FRP Coupler.

40 mm diaDSR 2022 18.7.3

SITC of advanced maintenance free enivironment friendly earthing consisting of 1 no. of 3 Mtr length , 17.2mm dai UL certified earth electrode made of high tensile low carbon steel circular rods,moleculary bounded copper on outer surface ( minimum copper bonding thickness 250Microns) with copper terminal to connect incoming strips ( Environment friendly backfill compound duly certified as per ANSI / NSF Standard 60 / Toxic content certificate as safe for use near portable ground water resources. The job includes; a)SITC of earth pit Chamber (300mm x 300mm) with CI cover for above b)SITC of Lightining strike recorder ( minimum four digit display) of not resetable type in an IP 55 enclosure. c)SITC of Down Conductor of 70sq mm single core insulated copper cable d)SITC of test link joint kit in a IP 66 weather proof enclosure of suitable dimension e)SITC of accessories to run the down conductor of Quantity.

100 mm diaDSR 2022 18.7.7

EXTERNAL FIRE FIGHTING RELATED WORKS

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads.DSR 20221 2850 lpm at 88 m Head DSR 2022 18.1.1

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft,mechanical seal conforming to IS 1520.Suitable HP, 1500 RPM water cooled with radiator,diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric tarting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office redcolour etc. as required.M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required.Suitable cement concrete foundation duly plastered and with nti vibration pads.DSR 20222 18.2 2850 lpm at 88 m HeadDSR 2022 18.2.1

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.DSR 2022 18.3 180 lpm at 88 m Heada 18.3.1

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets wleding , excavation & Providing Cement Concrerte blocks as supports etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade comple