SR of damage culvet parapet in Km- 1, 2, 3 at Bara Link Road and Km-1, 3 at Nawabad Link Road

Brick work with common burnt clay (non modular) bricks of class-150 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

12 mm cement plaster of mix : 1:4 (1 cement : 4 fine sand)

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Repeated / Tranvers bar) Providing amd laying of hot applied thermoplastic compound 5 mm thick including reflectorising glass beads @ 500 gms per sqm area, thickness of 5 mm is exclusive of surface applied glass beads as per IRC:35-2015. The finished surface to be level, uniform and free from streaks and holes. (MoRTH-803, Si No.-3)

Reflective Raised Pavement Markers (Cat Eye/ Road Stud) Supply and fixing of raised pavement marker with Made of Plastic body of RPM/ Road Stud shall be moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (High-imoact Polystyrene) or Acrylonitrite Butadien Styrene (ABS) or Any other suitable material approved by the Engineer. The Marker shall support a load of 13,635 kg tested in accordance with ASTM D4280. The Reflective panels shall consist of number of lenses containing single or dual prismatic cubes capable of providing total internal reflection of the light entring the lens face. Lenses shall be mouled of methyl methecrylate conforming to ASTM D788 of equivalent. The stop or retro-reclecting surface shall preferably be 35+/-5 degree to base and the area of each retro-reflecting surface shall not be less than 13.00 sq.cm. the marker height shall not be less than 10 mm and shall not exceed 20 mm & Width shall not exceed 130mm. The base of the marker shall be flat within 1.3 mm all road studs shall be legibly marded with the name, trade or other means of identification of the manufacture, epoxy installations, excess adhesive around the edge of the marker, excess adhesive on the pavement and adhesive on the eposed surfaces of the markers shall be immediately removed. The contractor shall submit a two year warranty for satisfactory field performance includingstipulated retro-reflectance of the reffecting panel to the Engineer. In addition a two year warranty for satisfactory infield performance of the finished road marker shall also be given by the contractor who carries out the work of fixing of reflective road markers. In case the markers are displaced, damaged, get wom out or lose their reflectivity compared to stipulated standards the contractor would be required to replace all such markers within 15 days of the intimation from the Engineer, at his own cost. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-charge. (MoRTH-804 RPM without Shunk)

Retro-reflectorised Traffic sign as per IRC-67-2020 providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC: 67-2012 made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of property designed foundation with M-15 grade cement concrete 45 cm x 45 cm 60 cm, 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, Object Hazards sign at Culverts (30x90 cm (Left/Right) Object Hazard) (MoRTH-801, Si. No.-18)