Running Works Contract for effecting various works for a period of six months in Thulukkapatti sub division of Virudhunagar Division

Amount

Running Works Contract for effecting various works for a period of six months in Thulukkapatti section of Virudhunagar Division

Loading&Unloading of 7.32m, 7.5m, 8m, 8.23m RCC poles

Loading&Unloading of 9m, 9.14m RCC poles

Loading&Unloading of RS Joists, tubular & rail poles (above 9.14m)

Transporting of poles from road side to Work spot7.32m, 7.5m, 8m, 8.23m RCC poles/km

Transporting of poles from road side to Work spot9m, 9.14m RCC poles, RS Joists, tubular & rail pole/km

Excavation of pole pit (1.25m * 0.5m*1.5m)in Normal Ground

Erection

Excavation of pole pit (1.25m * 0.5m*1.5m) in Rocky Ground

Erection

Excavation of pole pit (1.25m * 0.6m*1.83m) in Normal Ground

Erection

Excavation of pole pit (1.25m * 0.6m*2.19m) in Normal Ground

Erection

Concreting of poles as per Board Standards (2'*2'*5'). The material such as sand, jelly, etc., have to be supplied by the contractor except Cement supplied by contractor (Cement concrete mix 1:4:8 using 40mm hard broken stone including cost of labour charges.for placing Transporting of sant,jally,from box and water curing for 14 days etc,.complete.

Coping of poles

Coil earthing per pole & pole earthing

Excavation of stay pit (1.00m * 0.5m*1.5m)

Erection

V cross arm, Channel cross Arm4 1/2'

V cross arm, Channel cross Arm3 1/2'

LT Three phase cross arm

LT single phase cross arm

HT / LT TI fitting

Tapping channel cross arm

Erection of HT Side arm with stud

Erection of LT Side arm with stud

g.Guarding Cross Arm

For 7/4.09 ACSR (per span/wire)

For 7/3.35 ACSR or 7/3.15 AAAC

For 7/2.59 ACSR or 7/2.50 AAAC

Resagging of LT & HT. line of all sizes

Spilt Neutral Guarding

Flat Guarding (2 wires)

Flat Guarding (4 wires)

Fixing of one earthing device

Upto 150 KVA

Erection of centre support for 250 KVA DT (Including concrete)

Erection of feeder cable with open type fuse unit per feeder and for each addl feeder

Bus bar arrangement with open type

Loading and Unloading of distribution transformer Below 250 KVA

Loading and Unloading of distribution transformer 250 KVA

Loading & Unloading of all sizes of DT using private Crane vehicle

i)Loading /Un loading of Metering Set

ii)Erection / dismantling of Metering Set

LT Changing of pin point to cut point

HT Changing of pin point to cut point

Single Phase service connection

Three Phase service connection

Dismantling of deteriorated poles with concrete in damaged condition including grill separation etc.,

Dismantling of poles without concrete in damaged condition including grill separation etc.,

7.5Mtr /8Mtr PSC & Pole

9.14Mtr RCC Pole and above

Dismantling of stay with guy shackle complete

Replacement of detoriated stay rod

Dismantling of 3.5' V cross arm and channel cross arm

Dismantling of 4.5' and 5' V cross arm

Dismantling of TI Fitting

Dismantling of Single phase/ 3 phase cross arm

complete replacement of worn out earth wire per structure

For ordinary trees and thorn bushes and trees

For coconut and Palm trees

Pole (Colour washing with emulsion on Labour only) (Double coat)

Transformer structure (Double coat)

For transformer only (Double coat)

Set right of leaning of HT pole / LT pole including X arms, TI fittings

Excavation of structure pole pits 2Nos

Erection of structure poles 2Nos

Transformer structure pole mass concrete (All materials including cement (Ratio 1:2:4) and coping

Top channel

Transformer seating channel and belting angle

AB switch (complete)

HG Fuse (complete)

Jumpering

HT LAS

LT LAS

Fixing of capacitor bank in Distribution Transformer with wiring irrespective of capacitor

Excavation of 3 Nos. earth pits

Excavation of earth wire trenches and paving of earth wire, Erection of 3 Nos. earth pipe and giving earth connection, Earthing of all metal parts, Las etc., including central connection

Mason works for earth pits including material

Spreading yard jelly and cut stone and bricks including materials

9 mtr long RCC Pole (Square Section) complete

Maintenance of A/B switch

Maintenance of Single Pole Distribution Transformer and Structure complete

Replacement of GI wire in LT cut points replaced with Lt metal parts

Replacement of worn out AB Switch knife, checking of alignment and lubrication

a)Attending H.T jumper cut

b)Attending L.T jumper cut

a)Replacement of H.T Disc

b)Replacement of HT Pin insulator

a) Replacement of L.T shackle with metal parts

b) Replacement of L.T pin insulator

Maintenance of DP Structure complete

ப jumper provision ( including of service wire disconnection & reconnection)

Set right of Tilted X arm