SPECIAL REPAIR TO BLDG NO P-2/2 GROUND AND FIRST FLOOR IN OTM ACCN OF 173 MD REGT AND PROVN OF CONCEALED INTERNAL WIRING IN LIEU OF SURFACE WIRING IN BLDG NO P-437 TO P-452 AT ABDUL HAMID ENCLAVE AND AT AMRITSAR CANTT

Amount

Taking down shutter and removing from site of any description size but exc 1 sqm and n.exc 2 sqm ; Complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frame without taking of shutter and removing from site exc 1.5sqm but not exceeding 4 sqm each ; Complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frame (w/o taking off shutters) and removing from site n.exc 1.5sqm each ; Complete all as specified and as directed by Engineer-in-Charge.

Taking down shutters of any description exc 1.00 sqm & nexc 2sqm each. and refixing in the same opening ; Complete all as specified and as directed by Engineer-in-Charge.

Taking down cement plaster from wall's/ceiling including raking out joints hacking for key scrubbing down with water and dispose off debries upto distance n exc 500 metre where directed ; Complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (un-reinforced)in ground floor and paving n. exc 15 cm thick below or above ground level & dispose off debris upto a distance n. exc. 50 mtrs where directed ; Complete all as specified and as directed by Engineer-in-Charge.

Demolation of RCC in any position not otherwise specifically provided ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in hold fast block, roof kerbs or mud stop, coping, rounded or chamfered on edges and like including weathering, slightly rounded or chamfered angles and throating etc incuding necessary form work ; Complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work built in cement mortar, seperation, cleaning and stacking of serviceable bricks for reuse and removal of debris,rubbish to a distance exc 400 m but not exc 500m ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for brick work with sub Class 'B' old size bricks, straight or curved on plan exceeding 6 Metre mean radius, built in cement mortar 1:6 ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for brick work but except brick (serviceable brick obtained from demolition shall be reused), built in cement mortar 1:6 ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces and finishing the surface even and smooth (without using extra cement) etc ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 10mm thick cement plaster in CM (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth (without using extra cement) etc ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 15mm thick cement plaster in CM 1:4 on fair faces of brick work and finishing the surface even and smooth (without using extra cement) etc. ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for preparation of new plastered surfaces and applying two coats of oil bound distemper on walls ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for preparation of old decorated plastered surfaces, filling nail holes or patches with wall care putty to make surface smooth and applying two coats of oil bound distemper on walls ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for preparation of new plastered surfaces and applying three coats of white wash on ceiling ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for preparation of old surfaces and filling hole and patches with wall care putty to make surfaces smooth and applying one coat of white wash on ceiling ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for preparation of new plastered surfaces and applying two coats of cement base paint on wall ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for complete removal of existing treament including preparation of surfaces and applying two coats of cement base paint on walls ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repairs for solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube including taking down old frame any type ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be convered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20 mm width stuck inside with solvant cement for stiles and plain colour PVC sheet top rail, lock rail and bottom rail on either side and as gap insert of top rail and bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and raials with suitabale PVC sheet beading, and jointed together with solvant cement, fixing in the frame at side as per specification and drawing ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for Steel window 1.25mm thick box type ERW hollow P section of each frame size 60mmx25mm double rebated comprises of glazed & gaused Skelton shutter ERW section 50mmx20mm & 1mm thick with one openable leaf consisting of two number sash bars of T-Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1.25mm thick with following fittings welded to the frame shutter :- Ref Drg No CE JZ/TD-06/07 i) Hold fast 150mm long mild steel flat iron 12x3 mm made to shape- 04 Nos per window ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt 150mm long 2 No per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 Nos per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 Nos per leaf vi) pintol hinges 12 x 75 mm - 2 Nos each leaf vii) 10mm square Guard bar @ 10 cm c/c. (viii) 25 x 3 mm flat iron for joint of both frame wiremesh & Glazed welded inner side and outer side of frame (ix) (x) 0.36mm nominal dia of stainless steel wire mesh and average width of aperture of 1.40mm fixed in glazed / gazed skelton shutter of window (xi) 3mm thick sheet glass, ordinary quality and with oil putty in Square n. exc 0.5 sqm in each pane fixed in glaxed / gazed skelton shutter of window. (xii) Fabrication and fixing arrangements as per Drg No CE JZ/TD-06-07 including taking down, cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repairs for mild steel box type ventilator fixed type with glazing bar with mesh & glass as per drg No. CEJZ/TD-06/07 dt 07.06.07 primer coated ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for 30 mm thick flush shutter, soild core construction with block board core and plywood face panels commercial type on both side ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for 35 mm thick 2nd class hard wood glazed and skeleton shutter’s open rebated prepare to receive glass gauge etc edges of framing plain chamfered or rounded fitted with Cut and mitered bead’s for securing glass gauge etc size of member of shutters as per SSR Part-I Section-8 clause 8.2 (a) ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for 18mm thick PVC board in cup board shelve as in kitchen ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for 20 mm thick pvc shutter, printed one side with one coting of ultra violet chemical, glossymat finish inc 100% termite/water proof, fireretrandenteco friendly. Weight not less than 12 kg per sqm incl Steel piano hinges, steel catcher,aluminium handle100 mm long ,aluminium hasp & stapple in repairs ; Complete all as specified and as directed by Engineer-in-Charge.

Hacking out old broken glass any thickness, size, quality or description from steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for 3mm thick ordinary sheet glass and glazing with oil putty or fixed on steel frame, in squares not exc 0.50 Sqm in each panes ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repairs for stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for 300 mm size, aluminium alloy,anodized sliding door bolt, clip type, and fixing clips of sheets or extruded section and fixing of bolts and sliding bolts of extruded section fixed with stainless steel screw ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for butt hinges 100mm size medium weight cold rolled mild steel fixed with stainless steel screw ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repairs for 150 mm size aluminium anodized barrel tower bolt of extruded section fixed with stainless steel screw ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repairs for 300mm mild steel ordinary rat tail rod pattern spring including roller plate including fixing with nailsd/ bolts or welded ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repairs for 125mm size extruded aluminium anodized handle cast type fixed with stainless steel screw ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for mild steel powder coated curtain rods 22mm dia ( as per sample kept in GE's office) including knobs, brackets to hold the rod & a set of ABS finials ( as per sample kept in GE's office) of approved quality & appropriate qty of ABS plastic rings ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for Preparation of new wooden surface over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old painted wooden surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for applying two coat of synthetic enamel paint over a coat of red oxide, zinc chrome primer on steel surfaces exceeding 10cm width or girth including preparation of new surfaces ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old painted steel surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint ; Complete all as specified and as directed by Engineer-in-Charge.

Taking up or down steel water tubing and connections including cleaning serviceable pipe for refixing and removal of unserviceable pipe, bore of pipe 15mm complete all as specified. Note :- The quoted rates shall be include for necessary excavation and earth work, cutting/ chasing in wall/ floor and making good in CM1:3 ; Complete all as specified and as directed by Engineer-in-Charge.

Taking up or down steel water tubing and connections including cleaning serviceable pipe for refixing and removal of unserviceable pipe, bore of pipe 20mm complete all as specified. Note :- The quoted rates shall be include for necessary excavation and earth work, cutting/ chasing in wall/ floor and making good in CM1:3 ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for galvanized iron steel tubing medium grade 15mm bore with all fittings and fixed to walls, ceiling or laid in floor ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for galvanized iron steel tubing medium grade 20 mm bore with all fittings and fixed to walls, ceiling or laid in floor ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for Grating round 140mm size of PTMT ( minimum weight 50gms) ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repairs for PVC connection 450mm long of 15mm size with PTMT nuts on both sides ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for bib tap standard 15mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 15mm-90gms) ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for Pillar taps 15mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 15mm-110gms) ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repairs for stop valve 15mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 15mm-90gms) ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repairs for stop valve 20mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 15mm-90gms) ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repair for angle valve 15mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 15mm-90gms) ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repair for 15mm bore stop valves, cast copper alloy, concealed type, chromium plated with long shank and cup ,screwed down,handles, screwed both ends for iron pipe or for unions and fixed ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for vitreous china squatting pan ( Orissa Pattern) size 580 x 440 mm (white), with PVC P or S trap, integral foot rest including water connection to trap and flushing pipe, flushing cistern etc complete and bedding in PCC 1:7:12 type F-2 including taking down/dismantling old unserviceable WC ; Complete all as specified and as directed by Engineer-in-Charge. Note :- Flush pipe and flushing cistern to be measured and paid separately.

Supply and Fixing for white PVC valve less syphonic action type low level flushing cistern of 10 ltrs capacity with inlet ball valve, float valve, push button type handle including pipe 32mm dia of PVC(Heavy duty) flush pipe including brackets and taking down/dismantling old unserviceable cistern ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repairs viterous chinaware wash hand basin light colour/white of size 550x 400cm flat back or angle stay, brass chromium plated waste coupling, chain, plug, porcelain rubber stopper, brackets,32mm bore PVC waste pipe of appropriate length ilcluding taking out of old WHB & making necessary connections ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for rotational moulded polythelene water storage tanks(multi layer) capacity 500 litres(cylindrical vertical with closed top), with and including 20mm dia PTMT ball valve with epoxy coated aluminium rod ( minium weight 210gms ) hoisted, fixed in position and making connection including dismantling of existing unserviceable tank Exc 250 Ltr & not Exc 500 Ltr ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for swivel shower rose of PTMT for fixing with 15mm pipe ( minimum weight 40gms) ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for Towel Rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats (Minium weight 190 gms) ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for PVC shelf 12cm wide and 42 cm long fixed with screws ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour 25 mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in sub base and finishing the surface even & rough to receive floor finish ; Complete all as specified and as directed by Engineer-in-Charge.

Roughening of surface of old concrete floor, sweeping, clean and washing with water to remove dust ; Complete all as specified and as directed by Engineer-in-Charge.

Dismantaling floor hearth or wall tiling incl cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for Coloured/printed glazed creamic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.16 sqm, thick invertical surfaces(skirting/dado) including 10mm thick cement plaster in CM 1:4 ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for Coloured/printed non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over 15 mm thick screed bed or bedding layers in CM 1:6. ; Complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete in ground floors and paving not exceeding 15 cm thickness ( below or above ground level) and disposing the rubbish to a distance exceeding 50 Mtr but not exceeding 100 Mtr away to low lying areas ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for 50mm thick Cement concrete type D-2 , 1:4:8 (40 mm graded aggregate) as in sub base of floor ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete to achieve mirror finish laid over & including 20 mm thic screed bed in CM 1:6 ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for Machine cut kota stone slab flooring 20-25mm thick in riser of steps skirting dado and pillar laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete to achieve mirror finish laid over & including 10 mm thic screed bed in CM 1:6 ; Complete all as specified and as directed by Engineer-in-Charge.

Dismantling of PVC/CI pipe of 75/100mm dia fixed with cement joint ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for PVC (SWR) pipes 110mm dia bend any radius ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing for 110mm bore PVC (SWR) branch piece , single, equal fitted with oval access doors ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for PCC type D 2 (1:4:8) 40mm graded aggregate ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for machine pressed coloured chequered cement concrete tile ISI Marked of size 30cm x30cmx22-25mm thick over and including 15mm thick cement screed in CM 1:6 set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the colour of tiles complete all as specified.

Material and labour for repairing of RCC projection, chajjas, facia,bands, shelves, beams, RCC railing, balcony and similar works by dismantling of loose/ disintegrated portion RCC at any height and in any sitution floor (including provn of support, formwork and welding of reinforcement if required with wire mesh of eight 1.5 kg/ sqm and dubbing/ filling with PCC (1:2:4), type B-0, using 12.5 mm graded aggregate,15 to 25 mm thick after applying cement slurry @ 3 kg/sqm, finished even and smooth to desired shape and applying two coats of wheater proof emulsion paint to match with existing surfaces ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for cement concrete 1:5:10 (40 mm graded aggregate ) in lean concrete ; Complete all as specified and as directed by Engineer-in-Charge.

Dismantling of brick tiles single layers on roof, jointed and grouted / pointed in cement mortar including cleaning serviceable tiles and stacking properly for re-use, disposal of unserviceable tiles and debris /rubbish from site ; Complete all as specified and as directed by Engineer-in-Charge.

Demoliton of mud in roof any thickness including mud plastering and removing to distance exc 250m but n exc 500m ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in roof kerbs, sloping padding and finishing the surface even and smooth (without using extra cement) ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm includingcleaning surfaces etc ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( Wt not less than 150 gms /sqm ) laid on bituminous surfaces by forced application over entire roof area, sunken portion with overlapping 100mm to eiher side ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 40 mm thick brick tiles laid over and including 15mm thick bedding layer in cement mortar 1:6 and jointed, grouted and flush pointing as work proceed in CM 1:3 mixed with 5% of crude oil by weight of cement ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 40 mm thick brick tiles but except tiles (Serviceable brick tiles obtained from demolition shall be reused) laid over and including 15mm thick bedding layer in cement mortar 1:6 and jointed, grouted and flush pointing as work proceed in CM 1:3 mixed with 5% of crude oil by weight of cement ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for udaipur green marble 16-18mm thick confirming to sample kept in GE 's office ( table rubbed and polished inslab, stair case, step and like jointed with grey cement slurry mixed with pigment to match with shade of marble over and including 15mm thick cement screed bed in CM (1:6) ; Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for steel framed work as in chowkhat, doors of angle or other section complete drilled for fixing sheeting with all fitting and fixture ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing in repair for CI floor trap( long nose) 75mm bore with grating including Jointing to waste pipe fixed in PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) ; Complete all as specified and as directed by Engineer-in-Charge.

Taking down carefully copper / aluminium point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, sockets, lamp holders, brackets, bulk head fittings, tube light fittings etc. and making good disturbed surfaces of walls etc. as per existing finishes by plastering, repairs and white / colour wash etc ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for point wiring complete with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit incl accessories totally concealed in wall, ceiling/roof etc., with pressed steel terminal boxes of suitable size & modules, concealed in walls incl plastic laminated sheet cover 3mm thick as top cover fixed with cadmium plated screws for housing switches/sockets/regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly ; Complete all as specified and as directed by Engineer-in-Charge. (a) One light point/Fan point controlled by one switch NOTE: Pressed steel terminal boxes with a coat of synthetic enamel paint over a coat of red oxide to steel surface to avoid rust incl suitable thick laminated sheet cover plate for mounting switch/sockets/regulator/bell push etc, concealed in wall and Cost of cutting chases & making good to distrubed surface with cement mortar, if required any shall be deemed to be included in the quoted rate

Material and Labour for point wiring complete with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit incl accessories totally concealed in wall, ceiling/roof etc., with pressed steel terminal boxes of suitable size & modules, concealed in walls incl plastic laminated sheet cover 3mm thick as top cover fixed with cadmium plated screws for housing switches/sockets/regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly ; Complete all as specified and as directed by Engineer-in-Charge. (a) One socket outet point 5 amps on the same board. NOTE: Pressed steel terminal boxes with a coat of synthetic enamel paint over a coat of red oxide to steel surface to avoid rust incl suitable thick laminated sheet cover plate for mounting switch/sockets/regulator/bell push etc, concealed in wall and Cost of cutting chases & making good to distrubed surface with cement mortar, if required any shall be deemed to be included in the quoted rate

Material and Labour for point wiring complete with 1.5 sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit incl accessories totally concealed in wall, ceiling/roof etc., with pressed steel terminal boxes of suitable size & modules, concealed in walls incl plastic laminated sheet cover 3mm thick as top cover fixed with cadmium plated screws for housing switches/sockets/regulators etc, including provn of 1.5 sqmm nominal cross sectional area, PVC insulated, FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly ; Complete all as specified and as directed by Engineer-in-Charge. (a)One 3 pin 5 Amps socket outlet on independent board. NOTE: Pressed steel terminal boxes with a coat of synthetic enamel paint over a coat of red oxide to steel surface to avoid rust incl suitable thick laminated sheet cover plate for mounting switch/sockets/regulator/bell push etc, concealed in wall and Cost of cutting chases & making good to distrubed surface with cement mortar, if required any shall be deemed to be included in the quoted rate

Material and Labour for point wiring complete with 4.0 sqmm FRLS cable 1100 volts grade with multi stranded, copper conductor in and including non-metalic PVC conduit incl accessories totally concealed in wall, ceiling/roof etc., with pressed steel terminal boxes of suitable size & modules, concealed in walls incl plastic laminated sheet cover 3mm thick as top cover fixed with cadmium plated screws for housing switches/sockets/regulators etc, including provn of 4.0 sqmm FRLS, unsheathed, 1100 volt grade, multistranded single core green colour copper conductor for earth continuity connected to earth dolly ; Complete all as specified and as directed by Engineer-in-Charge. (a) one 3 pin socket outlet,15 Amps on independent board. NOTE: Pressed steel terminal boxes with a coat of synthetic enamel paint over a coat of red oxide to steel surface to avoid rust incl suitable thick laminated sheet cover plate for mounting switch/sockets/regulator/bell push etc, concealed in wall and Cost of cutting chases & making good to distrubed surface with cement mortar, if required any shall be deemed to be included in the quoted rate

Supply and Fixing switch piano, flush type, single pole, one way 5 Amp, 240 volt, white or ivory ISI marked ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing switch piano, flush type, single pole, one way 15 Amp, 240 volt, white or ivory ISI marked ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing bell push flush type single pole one way 5 Amps 240 volts ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for stepped type electronic fan regulator suitable watts, flush type 240 volts ,50 Hz suitable fopr ceiling fan 1200 mm sweep ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing switch socket outlet 5 pin, 2 in 1, 5 Amps, 240 volts ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing switch socket outlet 5 pin, 2 in 1, 5 and 15 Amps, 240 volts ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing buzzer Ding dong AC 240 Volts single po;e fixed over and including pressed steel sunk box of size 175x100 mm duly covered with 3 mm thick bakelite sheet ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing ceiling rose surface PVC/Polycarbonate, isolated body with face Bakelite 65x50 mm three terminal ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing Lamp holder angular type, PVC/Polycarbonate type with back plate suitable for batten fittings ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing LED blub 9 watt 230 volts ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, TPN 4 way, 240 volts grade with 200 Amps insulated rated bus bar, earth bar IP- 43 & IK-09, door earthing flush to wall, including testing suitable for fixing MCB SPN, SP etc, including taking down existing unsv one and removing from site ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for distribution board made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, SPN 8 way, 240 volts grade with 200 Amps insulated rated bus bar, earth bar IP- 43 & IK-09, door earthing flush to wall, including testing suitable for fixing MCB SPN, SP etc, including taking down existing unsv one and removing from site ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing MCB of SP 5 to 32 Amps current carrying capacity, 240V, 10KA 'C' curve fixed in the MCB DB complete with connection testing and commissioning including taking down old unsv one from the site ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing MCB SPN 32 Amps current carrying capacity, 240V, 10KA 'C' curve fixed in the MCB DB complete with connection testing and commissioning including taking down old unsv one from the site ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and FixingMCB TPN 63 Amps current carrying capacity, 240V, 10KA 'C' curve fixed in the MCB DB complete with connection testing and commissioning including taking down old unsv one from the site ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for sub main wiring with 1100 volt grade two single core FR Wire PVC insulated and unsheathed cable with stranded copper conductor 6 sqmm drawn into and including electrical grade PVC conduit not less than 25 mm dia with IS 9537 (Part-III) 1983 mark, or relevant ISI mark with all accessories fixed concealed including chase cutting in brick/ stone masonry for fixing conduit and making good the disturb surfaces of wall as per existing including 6 sqmm multi - stranded copper conductor as earth wire in green colour including taking down old unserviceable sub main wiring ; Complete all as specified and as directed by Engineer-in-Charge. NOTE: 3 single core 6 sqmm and PVC conduit shall be measured as one RM

Supply and Fixing LED light fitting 1x20 W, 220 V AC decorative boc type with driver double shided connection holder includin g LED Tube light connecting up with 3 core flexible copper conductor cable of suitable size from ceiling rose including taking down existing unserviceable one and removing from site ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing LED light fitting mirror type with high out out diffuser 2 feet , 10 watt 220 V AC decorative type with driver holder and LED lamp hoder and LED lamp including connecting up with rhree core flexible copper condutor cable of suitable size ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing LED roadway luminaries 35 Watt, 230 V AC outdoor type with epoxy black powder coated sheet, high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket of suitable size with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete incl connecting wire with flexible PVC insulated copper cables from ceiling rose to fitting complete and testing, including taking down existing unserviceable one and removing from site ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing ceiling fan 1200 sweep with down rod 240 volts white colour , ISI marked BEE 5 star rating with latest BLDC technology complete including fan capacitor, PVC canopy, rubber bush split pin handing clamp holdfasteners etc ; Complete all as specified and as directed by Engineer-in-Charge.

Supply, install & testing exhaust fan, Metal body 300mm sweep heavy duty, 240 volts, single phase, 900 RPM complete fixed to wall with suitable MS bolts, grouted to wall and connecting up including provision of MS louver, cable from connector to fan with 3 core flexible cable of size 24/0.2mm with copper conductor from ceiling rose to to exhaust fan including writing MES No. with synthetic enamel black paint including cutting hole suitable for fixing exhaust fan ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing storage electric heater (Geyser), flexible mounting of capacity 25 ltrs, single phase, 240 volts, AC, white colour, ISI marked BEE 5 star rated complete with high precision & externally adustable capillary thermostat for temp regulation, backup safety overheating capillary therrmal cut out at 95ºC, temperature display, etc., including provn of new suitable holding clamp, MS bolts, grouted to wall and connecting up including 3 core sheathed multi-stranded flexible copper conductor cable connected with 15/16 Amp plug top and provn of water connections with new PVC steel braided inlet/outlet connection pipe 15mm dia, 450mm long with two numbers brass union, NRV of suitable size, check/end nuts with washers, 15mm dia 100mm long nipples (02 Nos) for hot water and cold water connections including writing MES No. and making good to the disturbed surface in cement morter as required and testing ; Complete all as specified and as directed by Engineer-in-Charge. NOTE: Cost of flexible copper cable of 3 core, PVC steel braided inlet/outlet pipe of 15mm dia, 450mm long with brass union, NRV, check/end nuts, nipples, MS bolts, etc., and minor parts, if any, other than those are not specified in the schedule and required for smooth functioning of geyser will be deemed to be included in the quoted rate

Supply and Fixing galvanised steel water tubes medium grade with screwed socket joint together with and including all GI fittings such as bends, elbows, short piece connectionns, backnuts, caps plugs and unions etc laid in tranches/fixed on walls/laid on floors of 20mm dia including testing ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing brass CP mixer for mixing hot & cold water with crutch or butterfly handle screwed down for inron/PP-R/UPVC pipe conforming to IS:781 of 1984 pf 15 mm bore ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing Plug type bib taps, cast iron, screwed for iron pipe of 15mm bore and fixed ; Complete all as specified and as directed by Engineer-in-Charge.

Supply & laying in trenches/drawn through pipes or in road crossing/paths/drains/ducts/floors/along poles/equipments etc., of XLPE insulated, armoured with multistranded aluminium conductor cable conforming to IS-7098 Part-I (1998), heavy duty (LT UG cable) conforming to IS-1554, 1100 Volts grade of size 3.5 core 35 sqmm nominal cross sectional area including connecting up using suitable size double compression copper gland, testing and commissioning ; Complete all as specified and as directed by Engineer-in-Charge. NOTE: Excavation, earthwork, sand cushioning, brick protection & cable protection etc. will be measured and paid separately under relevant items of this schedule.

Supply and laying GI steel tubing light grade 40 mm dia for protection of cable on poles with clamps nuts bolts and washer under road crossing etc ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for Earthing complete in replacement with galvanised iron mild steel earth plate electrode 60 cm x 60 cm x 6.3mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with top edge of earth plate at a depth of not less than 1.5 m below normal ground level, connected to glavanised earth lead of GI wire of size 4mm dia by means of GI Bolts, Nuts, check nuts & washers and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 25mm dia from earth plate to Panel/DBs and water pipe 20mm dia GI medium grade from top of the earth electrode raised upto a level of 50cm above ground level, MS funnel with wire mesh embeded in earthing pit of size 30x30x30cm in PCC (1:3:6) type C-1 incl exposed surfaces smoth finished with 15mm thick cement mortar (1:6), RCC pre-cast (1:2:4 type B-1) cover slab of 40mm thick with 2 Nos. MS handles of 12mm dia suitable for carrying of pit cover, Angle iron frame made out of 40x40x4mm angle iron for 30x30mm PCC pit for holding the pit cover including providing charcoal or coke and salt in alternative layers of 15 cm including necessary earth work in soft/loose soil, returning, refilling and removing of surplus soil to a distance n. exc. 50 mtr testing complete all as shown in electrical plate No-3 of MES Schedule Part-I of SSR-2009 ; Complete all as specified and as directed by Engineer-in-Charge. NOTE: (a) Cost of excavation, earth work, watering pipe, test point, MS Funnel with wire mesh and PCC pit with cover will be deemed to be included in the quoted rate. No extra cost shall be paid to the contractor against these items. (b) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor & no extra cost will be given to the contractor.

Supply and Fixing fan rod not less than 4' long including clamps, hooks, holdfasteners etc. ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing sub main wiring with 2 runs of 4.0 sqmm single core, multi-stranded PVC insulated, FRLS unsheathed cable 1100 Volts grade with copper conductor drawn through and including concealed non metalic PVC conduit, medium grade, ISI marked, suitable size with conduit fittings and accessories concealed in wall/ceiling/floor including 1 run of 4.0 Sqmm multistranded PVC insulated FRLS, copper conductor cable as earth continuity conductor and connecting to common earth dolly incl taking down old unsv one from site ; Complete all as specified and as directed by Engineer-in-Charge. NOTE: Two runs of 4.0 sqmm copper cable and one run of 4.0 sqmm copper cable alongwith non metallic PVC conduit/conduit accessories will be measured as one unit length

Taking down carefully existing serviceable Ceiling fan/Wall mounted fan, ceiling cable end, etc., removing the fan for keeping in safe custody, hanging the ceiling fan with down rod after rewiring including clamps, hooks, holdfasteners etc and connecting up, including making electric connection from ceiling rose or connector to fan ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and laying in trenches/drawn through pipes or in road crossing/floors/along poles/equipments etc., of XLPE insulated, armoured with multistranded aluminium conductor cable conforming to IS-7098 Part-I (1998), heavy duty, 1100 Volts grade of size 70 sqmm 3½ core nominal cross sectional area including necessary double compression copper gland and connecting up using suitable size aluminium lugs testing ; Complete all as specified and as directed by Engineer-in-Charge. NOTE: Excavation, earthwork, brick protection & cable protection etc. will be measured and paid separately under relevant items of this schedule.

Supply and laying GI pipe light grade with all fittings complete fixed to walls/poles/ laid in trenches for protection of UG cable 80mm dia ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and laying GI pipe light grade with all fittings complete fixed to walls/poles/ laid in trenches for protection of UG cable 50mm dia ; Complete all as specified and as directed by Engineer-in-Charge.

Excavating in trenches not exc 1.5 meter wide and not exc 1.5 meter in depth for laying cables and getting out in soft/loose soil and in road cutting ; Complete all as specified and as directed by Engineer-in-Charge.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil ; Complete all as specified and as directed by Engineer-in-Charge. NOTE: Reddled earth upto 20cm depth around cable for protection to be filled including spreading, levelling etc & punned down

Removing excavated material/surplus soil not exc 50 meters and depositing where directed at a level not exceeding 1.5 meter above starting point

Supply and laying in trenches burnt clay bricks, sub class (Designation 75) 'B' of old size for cable protection over the cables ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for distribution board, vertical, made out of sheet metal enclosure (CRCA sheet) dust and vermin proof, double door, VTPN 4 way, 415 volts grade with insulated rated bus bar with nickel plated, isolated neutral bar and door earthing flush to wall, earth bar IP- 43 protection with poly urithene (PU) gasketing, IK-09 Mechanical impact resistance, including testing suitable for fixing MCCB, MCB TP/SPN/SP etc, including taking down existing unserviceable one and removing from site ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing MCCB triple pole and neutral (four pole) 160 Amp, 415 volts, 50 Hz, having thermal setting range 70% to 100% and adjustable magnetic setting and breaking capacity 36 kA including making incoming and outgoing connections ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for Earthing complete in replacement with galvanised iron mild steel earth plate electrode 60 cm x 60 cm x 6.3mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with top edge of earth plate at a depth of not less than 1.5 m below normal ground level, connected to glavanised earth lead of GI strip earth lead of size 25 x 4mm dia by means of GI Bolts, Nuts, check nuts & washers and other end of the earth wire connected to earthing test point and protected by galvanised iron pipe light grade 25mm dia from earth plate to Panel/DBs and water pipe 20mm dia GI medium grade from top of the earth electrode raised upto a level of 50cm above ground level, MS funnel with wire mesh embeded in earthing pit of size 30x30x30cm in PCC (1:3:6) type C-1 incl exposed surfaces smoth finished with 15mm thick cement mortar (1:6), RCC pre-cast (1:2:4 type B-1) cover slab of 40mm thick with 2 Nos. MS handles of 12mm dia suitable for carrying of pit cover, Angle iron frame made out of 40x40x4mm angle iron for 30x30mm PCC pit for holding the pit cover including providing charcoal or coke and salt in alternative layers of 15 cm including necessary earth work in soft/loose soil, returning, refilling and removing of surplus soil to a distance n. exc. 50 mtr testing complete all as shown in electrical plate No-3 of MES Schedule Part-I of SSR-2009 ; Complete all as specified and as directed by Engineer-in-Charge. NOTE: (a) Cost of excavation, earth work, watering pipe, test point, MS Funnel with wire mesh and PCC pit with cover will be deemed to be included in the quoted rate. No extra cost shall be paid to the contractor against these items. (b) On testing after completion of job, if desired earth resistance is not obtained, the earthing shall be redone by the contractor & no extra cost will be given to the contractor.